WRT54G ver 8.2 & LELA

Similar Questions

• How to install the WPA2-aes security on old router Wrt54G ver 6

  I need help mode WPA2 on my router, I got this router WRT54G ver 6 for several years and it works perfect only thing is that I have no security my nwireless can help them a whole? would be ppreciate it. Thank you

  Your router has the option for WPA2 Personal. You need to access the router interface so that you can select this type of security.

  Please click the link below and it will give you steps how to configure security wireless with your router:

  Title: setting up wireless security WEP, WPA or WPA2 on a Linksys ID of Article wireless router: 19073

  http://www6.nohold.NET/Cisco2/UKP.aspx?pid=80&VW=1&articleid=19073

• WRT54G Ver.2 communicates is not with my router

  I have a WRT54G version 2 and it does not communicate with my cable modem.  When I go into the Setup menu I have an IP from my modem and I have the default gateway with DNS servers.  When I try to access internet, I can't.  I have ping all addresses and when I get to the front door my application has been exceeded.  I have not changed the settings and I tried power cycling, but it still does not work.  The funny things is when I hard plugged the laptop to the modem cable I can access the internet fine, but not through the router.

  Anyone have any ideas on what is happening with the solutions?

  What "Internet Connection Type" that you use in the router?  You should probably use "obtain automatically an address IP (DHCP)".

  If you would like more information, please indicate your ISP and the brand and exact model of your modem number.

• I don't know what I'm doing... just trying to connect Router WRT54G ver 6 wireless...

  I have a new laptop and connect to comcast very well.  Now, I'm trying to connect to the linksys wrt54g wireless router.  I know I SHOULD KNOW this... but initially connected by Motorola SB5120 modem via ethernet cable.  What should I do next?  Would appreciate any help to help... Thank you very much.

  If your Internet service provider is cable follow this link to configure the router.

  If your DSL Internet service provider follow this link to configure the router.

• Connecting A Linksys WRT54G Ver 2 to an AT & T DSL 2Wire gateway Modem

  
  

  This link will give you instructions step by step how the router to another router or modem/router linksys cascade: cascade or connect a router to another Linksys router. If this link does not work for you, then you can follow the steps on this link on how to configure the router with a dsl connection, as long as you have an internet provider ADSL connection: setting up a router Linksys for DSL Internet connection.

• WRT54G Ver 6

  I have wss trying to set the security on my router. I enter the IP address with the password "admin" but the page need me has too many erros on this and I can't do anything on the page.  I was told that I have to upgrade the software for this version.  Any help would be appreciated.

  First you will want to download the latest firmware.

  You can try a hard reset, press reset for 30 seconds while the router is plugged in, while holding down the reset button unplug the router for 30 seconds, then (while keeping the reset button) connect back and hold the button for another 30 seconds. Give it some time to start then go to 192.168.1.1 and it will ask you for a firmware, apply the downloaded previously.

  Good luck

• WRT54G ver.2 Firmware Version: v4.21.1 - cannot connect wireless

  Hello

  These days I could not connect to my wireless network.  I have 1 office, cable that connects no problem.  2 laptops (win xp) that can both see the network at full power, but I am unable to connect.  I just get the dialog box "until the network... "and then it expires later on two laptops. I have reset the router, updated firmware, disabled the secutiry everything tried but nothing works.  I am able to connect to other networks in my apt complex, so I guess my laptops aren't the issue and that its my router.  again, it was something just all of a sudden, after no change in one of my installation.

  Any suggestions are greatly appreciated.

  Thank you

  Jason

  After an update of the firmware did you reset your router and reconfigure all the settings on it again? If this isn't the case, then press in and hold the reset for 30 seconds button... Release the reset button... Unplug the power cable from your router, wait 30 seconds and reconnect the power cable... Now re - configure your router...

  Here is the wireless settings that you can configure your router, and I think that should solve your problem.

  When you connect to the router configuration page, click on the Wireless tab

  -Wireless network mode must be mixed...
  -Provide a unique name in the name box of the wireless network (SSID) in order to differentiate your network from your network of neighbors...
  -Set the channel 11-2 wireless, 462 GHz... Wireless SSID broadcast should be enabled and then click on save settings...
  Please take note of the name of the wireless network (SSID) because it's the network identifier...

  For wireless security: -.
  Click the sub-tab under wireless > Wireless Security...

  Change the mode of WPA wireless security, encryption, select TKIP. Password input your desired WPA key. For example, MySecretKey, this will serve as your network key whenever you connect to your wireless network. Do NOT give this key to anyone and do not forget the key.

  NOTE: The password must be more than 8 characters...

  Click the settings advanced wireless

  Change the tag to 75 interval, change the Fragmentation threshold to 2304, change the RTS threshold to 2304 and click on save settings...

  Now let's see if you can locate your wireless network and try to connect...

• I need to replace my WRT54G?

  I have a WRT54G ver 3 I installed the firmware to verersion 4.21.1 as I am trying to add a new Windows 7 laptop with a Wireless N adapter to my home wireless network.  I can still connect my old XP SP3 computer to the Internet, but the new laptop still does not connect (I use DSL).  It detects the SSID and displays 'limited connectivity' to the WRT54G and no Internet connection.  The limited connection knows the router has WEP encryption and returns the correct encryption key, but it the IPv4 and IPv6 protocols show no network access.  Aside from obvious speed gains, if I need to replace my wireless router and it must therefore be a double tape drive to work with my 54 Mbps G-adapter on my old laptop and the laptop card Intel(r) Centrino Advanced-N 6200 AGN on the new computer?

  Connect the computer to the router with the Ethernet cable.

  Open the router configuration page.

  Go to the Wireless tab and change the name of the wireless network SSID (create a new wireless network). Change the channel to 11. Save the settings.

  Click the wireless security sub tab and change the security to WPA Personal mode. Enter the password for your wireless network. Save the settings.

  Go to the sub-tab to Wireless MAC filter and make sure that it is disabled.

  Go wireless advanced settings. Change the tag to 75 interval, RTS threshold and fragmentation to 2306. Save the settings.

  Now try to connect to the new network wireless on the old XP computer.

  Then try to connect to the network wirelessly on the computer windows 7.

• WRT54G can't internet

  My 'network' looks like this:

  CABLE MODEM ===> WRT54G

  WRT54G Port1 ===> PC

  PC running Windows/XP sp3 with all updates installed. However, there is no wireless network card.

  Label to the WRT54G ver.2 Watch model number. I don't think that the firmware has been upgraded.

  It's used to work. What has changed? The laptop which allows you to connect wireless is dead. I now have a 2nd PC located on the same table as the old PC. There is no wireless card with at this stage, but ultimately it is the old computer, will receive his internet connection without wire - ly, as computers will physically be in separate rooms. I don't see how these changes would affect the operation of the router.

  I have no idea how to solve this.

  TIA,

  Phil

  Hi cellist.p and welcome to the forums!

  Have you tried power cycling? If not, try turning off the computer > router > modem and set up the modem > router > computer to see if it works. If not, access the router page to see if it has an Internet IP address. Open the browser and then type 192.168.1.1, do not fill in the username and type admin for the password (unless you have changed it before), go to the status tab and check the WAN/Internet IP address.

• Security WRT54G problems

  I see a lot of posts here that address of wireless security, but I have a few questions that I can't find answers to. I apologize if I missed something.

  I'm running a wrt54g ver.2. I don't think that the firmware has already been upgraded (how do you know for sure?). Two PC will access the internet through the router, either wireless or wired connection at different points in time.  A PC running XP, the other runs Windows7. There will eventually be a laptop running Windows7.

  QUESTIONS

  1. I changed the router access password. The first time I connected wireless, I had to provide the password. Since then, I have not been invited for the password when connecting. I don't know that I deliberately did something to cause the router to allow this specific computer to connect without providing a password again: I may very well have done something I don't remember not or that I have not to the achieve of time was to "Save" the password. Is there a way to verify that other computers, which have not already provided the password, it will prohibit to connect? Like, is there a place I can display using 192.168.1.1 which will definitively confirm course status?
  2. Is the password to connect the same as the password for the management of the router put in place through 192.168.1.1? The reason I am wondering is that I am still able to get to 192.168.1.1 with the admin password. I have not tried using admin from a computer that is already connected to the internet via the router. -What makes the difference?
  3. In the same sense that question #2, https in 192.168.1.1 option affect only computers that are not connected to the internet through the router? I haven't specified the https option. My concern is that once I have specify the https option, I won't be able to get to 192.168.1.1, because my computer is not a valid certificate.
  4. Y at - it a display by 192.168.1.1 which will show you which computers are connected?
  5. The firmware update will bring extra security?

  TIA,

  Phil

  <3. this="" ones="" a="" good="">lu>

  Yes. This is one I had read entirely and returned through more than once. I was pretty well convinced of the position of the expert called (9000 + posts was?), until I read this:

  <10 locks="" are="" more="" secure="" than="" 2.="" why="" don't="" you="" use="" 10?="">

  I'm always a bit wary when someone tries to make a point with this kind of rhetoric, instead of the straighforward more ' well 10 locks may be safer than the 2, I'd use more than 2 because...» ». This is the part 'because' who is absent. So I left not being not sure what position is more convincing.

  4. maybe you can try Network Magic.

  OK, I just downloaded the free trial version. I'll reportbravohelen:

  Thanks for your help, p4p.

  Phil

• WRT54G keeps restarting with Windows 7

  Hi guys, I really need help here, I use a laptop with Win 7 Home Premium + WRT54G ver 7. Whenever I connect my laptop via LAN or wireless network, the NVA WRT54G 7 keeps restarting that it self. I try to use another laptop with win xp and it works perfectly well,

  How can I fix? can someone help me?

  Sorry for my bad English, because this isn't my mother tongue,

  Follow this link to download the firmware for WRT54G ver.7.

• WRT54G Router will not connect on my iPhone automatecally

  Router: Linksys WRT54G ver. 2

  Firmware: 4.21.1 (last)

  Security: WPA2 Personal

  iPhone: 3GS

  Can I connect my iPhone to my wireless network, if I broadcast the SSID of the router, but if I turn off the show and then the iPhone can not connect automatically. So, I get the name and the network security code whenever I turn on my iPhone? And I do not broadcast the SSID.

  In fact, Disabling SSID broadcast is a bad thing that lowers your security.  The reason of this, it is related to the problem you are having with your iPhone.  SSID was intended to be broadcast - go ahead and rebroadcast.

  When a Windows-based computer connects to a "hidden" network, should be a note that the SSID is not broadcast.  From that moment, every time that Windows computer does not have a network connection, it will constantly send the connection requests that you guessed, clearly understood the SSID.  If not, how the Windows computer would be able to connect?  He doesn't know that its in your home and close enough to your router.

  The problem is of course that the Windows computer, typically a laptop, will do it everywhere wherever you are.  These packages are easily detectable with the simpler network analysis tools - and striker will be able to detect both your SSID and your MAC without being anywhere near your network address domestic.

  Computers (and the iPhone) which are only connected to the "visible" networks don't need to do.  They used scan, looking for those broadcast of the SSID, and then are alive when they find one they know.

  The iPhone is a phone, and he needs to save on battery life, so he cannot have the luxury of these packages to search daily for each hidden network, you connect to, so the problem of broadcasting.

  Take a look at this article From Microsoft TechNet for more information.

• Rebound strength of signal after Firmware update

  Have two of WRT54G wireless routers.

  A WRT54G version 6, Version of the Firmware v1.028

  A WRT54G version 6, Firmware Version v2.x

  With the WRT54G ver. 6, v1.028 Firmware version

  When I ran the android WiFi Analyzer app, I get mixed results.

  On my Samsung Galaxy S3, I saw my signal on channel 2 and others around me (two on Channel 6) and two on channel 11.

  On my first processor ASUS TFT201, I see the same signals, but my router signal bounces between the base line (-100dBm?) and on - 35dBm.

  Plugged the WRT54G version 2, Firmware Version v2.x channel 8

  Hung and got good strength constant signal. He had "WPA - Shared Key" but had not only not "WPA - Personal" that was on version 6. So, I had to go and live things. I upgraded this Firmware Version: v4.21.5 and guess what?

  I now "WPA - Personal". I have also a signal bounces on BOTH units. Here's the thing still more strange...

  On my ASUS, I can see both routers. Version 2 AND version 6 bounce between base and - 35dBm, in unison. Apprently dislikes something in the ASUS Firmwares later.

  On my Samsung I can see the two signals - version 2 on channel 8 is steady as a rock and version 6 on channel 2 is also bouncing back, but at a much slower pace!

  Speedtest.net running a PC connected to the worm. 2. I get 5.34 MB/s in Download and 0.47 MB/s in upload (Yes, my sucks Internet!)

  Speedtest.NET running through the ASUS WLAN to the worm. 2. I get 2.43 Mbps Down and 0.65 Mb/s Up.

  Speedtest.NET running through the Samsung wireless to the worm. 2. I get 5.07 Mbps Down and 1.07 Mbps Up.

  Any ideas on what's going on? I can get the old firmware and back, or is there another, better steps to take?

  Thank you!

  John

  First, I want to know how are the routers are connected as physically and what type of configuration that you put on them? Also, since you had put routers to level to recent versions, make sure that they had been manually reset and reconfigured to have the new firmware loaded correctly.

• WRT1900AC cannot see Wireless Bridge

  Hi all...

  I have a WRT1900AC (FW 1.1.8.161917) the router and wish to connect a wireless bridge that is connected to my DirecTv box.  I have an old WRT54G ver 3.1 running DD - WRT which I did in a wireless bridge.  I have good connectivity to and from the DirecTv box, but no connectivity to my gw wireless which is my WRT1900AC.  The WRT1900AC can't see the wireless gateway that is.  I have triple checked that I have the identifier SSID is correct and the security in the WRT54G wireless setting and even tried to use an old bridge G from Linksys to connect wireless and the exact same problem occurs when.  No device can see other wireless.  I suspect the WRT1900AC as the source of the problem.  Wireless gateways both try to connect 2.4 Ghz radio.

  Any ideas?  Thanks in advance.

  -Andy

  Reset the DirecTV box and we're ready now.

• Reset default

  I have a WRT54G Ver 3 with Firmware 4.21.1

  Whenever there is an electric spark (temporary failure) the unit stops working.

  I have to press the button Reset, then new all data from the user until the device is usable.

  I would thing there would be some kind of back-up or a memory that would avoid this, but can't find any mention of it.

  Is this a normal reaction to an electrical spark and if not, is there something I can do about it. ???

  Plug in the router on the UPS as well as your computer is turned on. Who will manage the power problems.