WRT54G ver.2 Firmware Version: v4.21.1 - cannot connect wireless
Hello
These days I could not connect to my wireless network. I have 1 office, cable that connects no problem. 2 laptops (win xp) that can both see the network at full power, but I am unable to connect. I just get the dialog box "until the network... "and then it expires later on two laptops. I have reset the router, updated firmware, disabled the secutiry everything tried but nothing works. I am able to connect to other networks in my apt complex, so I guess my laptops aren't the issue and that its my router. again, it was something just all of a sudden, after no change in one of my installation.
Any suggestions are greatly appreciated.
Thank you
Jason
After an update of the firmware did you reset your router and reconfigure all the settings on it again? If this isn't the case, then press in and hold the reset for 30 seconds button... Release the reset button... Unplug the power cable from your router, wait 30 seconds and reconnect the power cable... Now re - configure your router...
Here is the wireless settings that you can configure your router, and I think that should solve your problem.
When you connect to the router configuration page, click on the Wireless tab
-Wireless network mode must be mixed...
-Provide a unique name in the name box of the wireless network (SSID) in order to differentiate your network from your network of neighbors...
-Set the channel 11-2 wireless, 462 GHz... Wireless SSID broadcast should be enabled and then click on save settings...
Please take note of the name of the wireless network (SSID) because it's the network identifier...
For wireless security: -.
Click the sub-tab under wireless > Wireless Security...
Change the mode of WPA wireless security, encryption, select TKIP. Password input your desired WPA key. For example, MySecretKey, this will serve as your network key whenever you connect to your wireless network. Do NOT give this key to anyone and do not forget the key.
NOTE: The password must be more than 8 characters...
Click the settings advanced wireless
Change the tag to 75 interval, change the Fragmentation threshold to 2304, change the RTS threshold to 2304 and click on save settings...
Now let's see if you can locate your wireless network and try to connect...
Tags: Linksys Routers
Similar Questions
-
WRT54G Firmware Version: update v7.00.7 Beta?
Hello
I have a router wireless EMEA WRT54G v7 with Firmware Version: v7.00.7 Beta. I can't find an update of the firmware on the site.
Can you please help?
Thank you
Firmware update is available. Version 7.00.8 is available on the EMEA website. Click here!
It is enough to click on "Downloads" and select the correct hardware version.
-
Site WEB BLOCKED on WRT54G V6 (Firmware Version: v1.02.8)
Hello friends,
In short: why block some Web pages and others do not use this feature in my router? As mentioned above, I run a small office and uses one: WRT54G V6 (Firmware Version: v1.02.8): router.
For example, I managed to block sites like 'sex.com' and others. Also, blocking sites by keywords such as: News, music, vid, naked, etc. BUT, when I try to block FACEBOOK or TWITTER or by URL or keyword, guess what: IT DOES NOT WORK...!
No idea why this is happening and how can I be successful in the configuration of this feature? I'd appreciate that! Blessings...
Just to let you know two things:
1. I contacted Linksys live chat and they confirmed Web sites I want blocked using the protocol https, thye can not be blocked because the router features
2. as mentioned before, I warned an account with DynDNS as you suggest, followed their instructions, and after 24 hours or more, the protection is active...! Now no one in my little office is losing work time to monitor their FB status or send tweets! In addition, because my office is on the first floor of my house, I have peace of mind because I can block different sites using their "protection plans" categories: sport, games, porn, social media, blogs, videos, etc. I love...! I would recommend this service to anyone
Thank you
-
How do I know the hardware version WRT54G to only the firmware version and date
Hi - on a Linksys WRT54G, serial numbers and the version number have
been worn except in the case of the unit, so I don't know what version it is. He has since been released in it's 'safe place' to which I don't have physical access (and yet they want me to admin it). Don't think that I even get cable connect, wireless only. Gee. In any case... of the configuration screens I see:The current version of the firmware is 1.00.6 January 20, 2006.
I could, I guess that to get the MAC addressThe default login and password are what is active.
Can you tell what version of the material is, so that I can download the
good firmware flash update?
Thank youThe best way is to check the hardware, but as you mentioned, it is not an option. I suggest that you check each firmware release notes, check the previous firmware versions and dates on each version of the output material. However, it may be tedious.
-
WRT54G (version 2) Firmware Version Question
Hello
Beautiful room here. I'm glad that this facility exists.
I have the router WRT54G version 2. Finally, I upgraded the version of firmware years before Cisco Linksys bought.
A recent announcement by the people of Black Hat (treaties in this article of TechSpot) about their intention to publish a validation tool to exploit a vulnerability of DNS rebinding on a great many routers SOHO forced me to check for the latest update of firmware for my router.
The interesting thing is that my router's Web interface lists the current version of the firmware as 4.30.12, but the latest version of the downloadable firmware that I see listed on the support site is 4.21.1. I'm not very surprised by this apparent anomaly. If I remember correctly, that firmware version 4.30.12 download is a beta that was supposed to fix a problem connecting WiFi to a certain type. If this version of the firmware was still considered a beta at the time of the acquisition of Linksys by Cisco - or a 'stable' later firmware version incorporating the same or better fixes for the issues addressed by 4.30.12 that had been produced at that time-so maybe 4.30.12 was ruled out.
If you read the article of TechSpot and the associated table of preliminary vulnerability, test reports, you'll see that router WRT54G version 2 is not specifically listed. Version 3 of the router is listed as vulnerable, and version 5 of the router is not.
So, my questions are:
Everyone here is aware of information indicating whether or not the problem of DNS Rebinding vulnerability affects the WRT54G version 2 with the last registered (4.21.1) router firmware version?
If so, does anyone know if yes or no Cisco plans to release an update for this old router?
If the router is vulnerable and will not be solved with a firmware update I'll probably have myself a new LInksys router which is not listed as vulnerable. (Believe me, I'm not leaving this thread to bash Linksys. This router ran like a train of 24 hours a day for years without a single hiccup that was not directly attributable to the problems of the ISP. For the price, it's one of the best purchases of equipment I've ever done calculation. And I have done this since the beginning of the 80s when I was using a CP/M system and an Apple / / e.)
If the 4.21.1 version firmware for WRT54G version 2 is not affected, I wonder if anyone knows if yes or no 'downgrading' of 4.30.12 to 4.21.1 is likely to lead to a failure of the router. (I'll probably try it anyway. If it brick the router I'll just go ahead and get a new one.)
BTW, I use this router with the ease of remote administration and UPnP off and strong admin password that is changed each week. (When I always used wireless I used WPA2 AES with strong password, but I am all wired now with the systems running Debian testing).
Forgive me for talking to myself. I decided to just go ahead and "downgrade" of the 4.30.12 firmware 4.21.1 version - just because I prefer to use a version of firmware known and supported for this material. The downgrade has gone well, so no worries about this.
I'll look for news on whether or not this version of the firmware on this particular router is vulnerable to the flaw in DNS rebinding and acts accordingly.
Sorry for the noise.
-
WRT54GS with Speedbooster, what version number?
Hi all
I was going to update my firmware for routers (w/speedbooster WRT54GS), so I check the bottom of the router... find model number... BUT there is no number of "worm" after her. Which firmware version to use?
Thank you for comments or ideas,
Brian
Go to Wikipedia.org and search for WRT54GS.
Then, using the serial number of your router, you can determine the version.
-
Calculator chart 50g. How can I find my firmware version? Thank you, johnnaben
How can I find my firmware version?
Thank you
johnnaben
I thank very much - the two methods have worked
johnnaben
-
R7000 - change of firmware version
I already had firmware version: V1.0.6.28_1.1.83 installed, but now find the newest website is Firmware Version V1.0.4.30_1.1.67. Why the most recent version is down? I would like to re - download version V1.0.6.28_1.1.83
Thank you
-
I just upgarded my R7000 for the latest firmware of the device itself. Now, I have an additional network that matches my real network called NETGEAR41-arlo_246912. I tried to switch my camera on another channel, and he followed. He got the exact same force that my wifi. The net effect is that I have 2 signals on channel and my coverage and bandwidth has suffered.
Anyone know what it is and how to turn off?
OK, found a similar bug by someone else with a solution:
Basically, they have added a feature and it enabled by default. It is in the STANDARD settings and no ADVANCED setting. Disable the arlo. Ugh.
-
Hello!
I am a new user of router dual-band WRT1900AC . The installation has been updated instantly to
Firmware version: 1.1.10.167514
Release date: June 30, 2015My WRT1900AC is configured as a wireless gateway.
https://community.Linksys.com/T5/wireless-routers/WRT1900AC-as-wireless-access-point/TD-p/847286
Also, I have disabled firewall and uPnP.
A tutorial here:http://www.Linksys.com/us/support-article?articleNum=140371
Everything works except that without access to the router config page.
The problem is, I can't access my page to config WRT1900AC Wireless Access Point and the only solution is to connect temporary exit HAND ROUTER LAN to WAN WRT1900AC, can I access my AP
(after restart of course). Change after I return the cable to the LAN again and restart WRT1900AC. This works.
Yesterday, I spoke with live chat. I received recommendations:
"Once the router is configured to bridge fashion, page configuration accessible only using its new IP address. The new IP address can be found on the main router DHCP table. It is because only in LAN - LAN, theWRT1900AC will be his disabled DHCP. »
I also saw Table of customer routers main DHCP but I have not found the IP address of my wireless WRT1900AC Access Point there. I think it is a bug in the version of the Firmware: 1.1.10.167514
Page config in the case of WRT1900AC Wireless Access Point is isolated or possible only thanks to the WAN WRT1900AC. It would be nice if someone confirms that and maybe in the next version offix. :-) I have a beautiful smartphone App "Smart Wi - Fi" and I can not comfortably use it due to this error/bug.
Otherwise everything works well and stably.inspire wrote:
Hi chadster766!
Thanks for your suggestion and a quick response. I have a feeling it would work then as you described. But how to set Internet settings in mode Bridge? I've already put a static IP address router IP address WRT1900AC. I see it with IP scanner.
If I leave the cables as you suggest (hand router LAN to WAN WRT1900AC), the Internet does not work. In this case go to the config page, but Internet with other devices will not work. Also good Wifi, it works but can not access. How to set the Bridge Mode? (I think this is my problem in this scenario)IP address of the router (LAN):
Connectivity-online-online details router LAN => Edit
* If your main router IP subnet example is 192.168.0.x, then set the address of the WRT1900AC IP to an IP outside the range of the main router DHCP. Ex: 192.168.0.2
Bridge mode:
Connectivity-online Internet-online IPv4 settings => Edit-online Bridge Mode -
How to install the WPA2-aes security on old router Wrt54G ver 6
I need help mode WPA2 on my router, I got this router WRT54G ver 6 for several years and it works perfect only thing is that I have no security my nwireless can help them a whole? would be ppreciate it. Thank you
Your router has the option for WPA2 Personal. You need to access the router interface so that you can select this type of security.
Please click the link below and it will give you steps how to configure security wireless with your router:
Title: setting up wireless security WEP, WPA or WPA2 on a Linksys ID of Article wireless router: 19073
http://www6.nohold.NET/Cisco2/UKP.aspx?pid=80&VW=1&articleid=19073
-
I try to use the multipath regular linux (device-map-multipath) with my PS6100 and it doesn't quite work. It gives me "readsector0 Auditor reports path is down," "pdu (op 0 x 50000370 itt 0x1) rejected.» Code 0 x 4 reason"errors and my iSCSI connections are reset every few seconds. My OS is Oracle Linux 5.10 (fully updated) and my PS6100 is running with the latest firmware version 7.0.5.
The latest kit from Dell STRUCK for Linux, 1.3.0-2, works fine on this machine, but the reason why I'm putting multipathd is to compare the performance between the two solution. If we look at the other system we have that run the ordinary multipathd, paths of Dell could give us performance. We doubt it, but we want to do the tests and a comparison of its performance stats.
We have another server which has almost the same configuration (same OS connected to an another PS6100) and multipathd works well on this one. And one of the difference between this system and no work is that the PS6100 is running on firmware 5.2.5 instead of 7.0.5. I'd be willing to downgrade firmware (this unit is not yet in production, and I don't mind losing the data on it) but I'm not find anything on the internet that show how other that of the "call from Dell and it'll do it for you. If the only thing you need to do is a special command in the CLI then why there is no documentation on this subject?
So I wonder if anyone here runs a firmware equallogic 7.0.5 with the multipathd of linux and a RedHat 5 of operating system (Oracle Linux, Redhat, CentOS, etc.)?
Hello
It is documented in the release notes for the firmware 7.0.x. There is a bug in Multipathd, which is exposed with 7.0.x. firmware. Replace readsector0 TUR or ARM and restart multipathd. Protocol errors will stop and Linux MPIO works perfectly.
Kind regards
-
RAID Controller degraded by the Firmware version
Hi all
My security system is sending me alert because my RAID controllers being day. RAID controllers are fine, but the State is deteriorating because of the "latest Firmware Version available" which means I can't properly control if something really bad happens.
Is it possible to disable the alert or lower the minimum version expected? I just can't reboot all my servers just for an update of the RAID firmware.
My security system expects a status: Ok
Thank you very much in advance!
Greg
Below the output omreport:
omreport storage controller $
Controller PERC H700 integrated (Embedded)Controllers of
ID : 0
Status: No reviews
Name: PERC H700 integrated
Location ID: shipped
State: degraded
Firmware version: 12.10.1 - 0001
Latest Version of the Firmware available: 12.10.4 - 0001
Driver version: 00.00.06.14 - kh1
The minimum required driver version: not Applicable
The Storport driver version: not Applicable
Minimum required: Version of the Storport driver: not Applicable
Number of connectors: 2
Regeneration rate: 30%
BGI Rate : 30%
Consistency check rate: 30%
Rebuild rate: 30%
Alarm status: not applicable
Cluster mode: not Applicable
SCSI initiator ID: not Applicable
Cache memory size: 512 MB
Patrol read mode: manual
Patrol read status: stopped
Patrol read rate: 30%
Read the iterations of patrol: 2
Give up control of consistency error: disabled
Enable reversible hot spare and replace the: enabled
Load Balancing: not Applicable
Auto Member Replace on Predictive Failure: disabled
Redundant path view: not Applicable
Able CacheCade: Non Applicable
Persistent backup: disabled
Encryption Capable: Yes
Currently key encryption: No.
Encryption mode: no
Preserved cache: No.
Spin down drives unconfigured: disabled
Turn down hot spares: disabled
Centrifuge the configured drives: not Applicable
Automatic disk Power Saving (idle C): not ApplicableThanks again!
gcharotIs it possible to update the firmware without system reboot? I am running CentOS 5 and 6No, you can update the firmware without a reboot, but the update will be based in the controller cache until a reset is performed. So yes, you can perform the update without reboot, but it will not take effect until you perform a reboot.
Thank you
-
How to get the driver network card and on the use of the PowerCLI firmware version?
Hi all
I would like to know if anyone can help me in sharing the PowerCLI script to list the server NETWORK card driver and the firmware version?
Note: I use the HP Blade Server and it's manual ESX - CLI command output:
HP BL 465c G8 ~ # ethtool-i vmnic0 pilot: be2net version: 10.5.65.4 firmware version: 10.2.340.19 bus-info: 0000:04:00.0 HP BL 465c G7 ~ # ethtool-i vmnic0 pilot: be2net version: 10.2.293.0 firmware version: 4.9.416.7 bus-info: 0000:04:00.0 Any kind of help would be greatly appreciated.
Thank you.
PowerCLI Version
----------------
VMware vSphere PowerCLI 6.0 Release 2 build 3056836
---------------
Component versions
---------------
VMWare AutoDeploy PowerCLI component 6.0 build 2358282
VMWare ImageBuilder PowerCLI component 6.0 build 2358282
VMware vSphere PowerCLI component 6.0 build 3052101
It works for you?
$esxName = "MyEsx".
$esxcli = get-EsxCli - VMHost $esxName
$esxcli.network.nic.list () | %{
$esxcli.network.nic.get ($_.) Name) |
Select Name,
@{N = "Driver"; E={$_. DriverInfo.Driver}},
@{N = 'Version'; E={$_. DriverInfo.Version}},
@{N = 'Firmware Version'; E={$_. DriverInfo.FirmwareVersion}}
}
-
Hi all
mattboren created the script below for a list of BIOS hardware version and firmware version:
## Script function: quickly get BIOS date, Smart Array FW version, and iLO FW version for HP hosts in a given location (folder, cluster, datacenter, etc.) ## Author: vNugglets.com -- Sep 2011 ## folder in which hosts in which we are interested reside #$strHostsFolderName = "myFolder" #Get-View -ViewType HostSystem -Property Name, Runtime.HealthSystemRuntime.SystemHealthInfo.NumericSensorInfo -SearchRoot (Get-View -ViewType Folder -Property Name -Filter @{"Name" = "^$([RegEx]::escape($strHostsFolderName))$"}).MoRef | %{ ## cluster in which hosts in which we are interested reside $strHostsClusterName = "Production" Get-View -ViewType HostSystem -Property Name, Runtime.HealthSystemRuntime.SystemHealthInfo.NumericSensorInfo -SearchRoot (Get-View -ViewType ClusterComputeResource -Property Name -Filter @{"Name" = "^$([RegEx]::escape($strHostsClusterName))$"}).MoRef | %{ $arrNumericSensorInfo = @($_.Runtime.HealthSystemRuntime.SystemHealthInfo.NumericSensorInfo) # HostNumericSensorInfo for BIOS, iLO, array controller $nsiBIOS = $arrNumericSensorInfo | ? {$_.Name -like "*System BIOS*"} $nsiArrayCtrlr = $arrNumericSensorInfo | ? {$_.Name -like "HP Smart Array Controller*"} $nsiILO = $arrNumericSensorInfo | ? {$_.Name -like "Hewlett-Packard BMC Firmware*"} $nsiNXdev = $arrNumericSensorInfo | ? {$_.Name -like "nx_nic device*"} $nsiNXdrv = $arrNumericSensorInfo | ? {$_.Name -like "nx_nic driver*"} if ( $nsiNXdev.Count -gt 0 ) { $nsiNXdevice = $nsiNXdev[0].Name } else { $nsiNXdevice = "n/a" } if ( $nsiNXdrv.Count -gt 0 ) { $nsiNXdriver = $nsiNXdrv[0].Name } else { $nsiNXdriver = "n/a" } New-Object PSObject -Property @{ VMHost = $_.Name "SystemBIOS" = $nsiBIOS.name "HPSmartArray" = $nsiArrayCtrlr.Name "iLOFirmware" = $nsiILO.Name "nx_nic device" = $nsiNXdevice "nx_nic driver" = $nsiNXdriver } ## end new-object } | Export-Csv C:\temp\Production-BLadeG7.csv ## end Foreach-Object
However, I would like to change the driver for the CARD and the version of the firmware but still appear.
Any kind of help and suggestions would be greatly appreciated.
Thank you.
Try like this
$strHostsClusterName = 'production '.
Get-view ViewType - HostSystem-Property Name, Runtime.HealthSystemRuntime.SystemHealthInfo.NumericSensorInfo - SearchRoot (Get-View - Name ClusterComputeResource-property - ViewType filter @{'Name' = ' ^ $([RegEx]: escape ($strHostsClusterName)) $"" "}). MoRef | %{
$arrNumericSensorInfo = @($_.) Runtime.HealthSystemRuntime.SystemHealthInfo.NumericSensorInfo)
# HostNumericSensorInfo for controller table of BIOS, ILO,
$nsiBIOS = $arrNumericSensorInfo |? {$_. {Name: like "* system BIOS *"}
$nsiArrayCtrlr = $arrNumericSensorInfo |? {$_. {Name - like "HP Smart Array Controller *"}
$nsiILO = $arrNumericSensorInfo |? {$_. {Name - like "Hewlett-Packard BMC Firmware *"}
$esxName = $_. Name
$esxcli = get-EsxCli - VMHost $_. Name
$esxcli.network.nic.list () | %{
$esxcli.network.nic.get ($_.) Name) | %{
$props [ordered] = @ {}
VMHost = $esxName
"SystemBIOS" = $nsiBIOS.name
"HPSmartArray" = $nsiArrayCtrlr.Name
"iLOFirmware" = $nsiILO.Name
"nx_nic device" = $_. Name
'nx_nic pilot' = $_. DriverInfo.Driver
"nx_nic driver version" = $_. DriverInfo.Version
"nx_nic firmware version" = $_. DriverInfo.FirmwareVersion
} # end new object
New-object PSObject-property $props
}
}
} | Export-Csv C:\temp\Production-BLadeG7.csv # end Foreach-Object
Maybe you are looking for
-
Entry door two s in El capitan
Anyone got two bridges working in El Capitan? Is it still possible? With two gateway is average, each interface has a bridge and both work.
-
Upgrade to El Capitan Mountain Lion
Can I move to El Capitan of Cougar or do I go to Yosemite first?
-
C309a get HP-CUE-scanning flow component has encountered a problem and needs to close
I am running Windows xp sp3. I meet it when scanning, other functions of the printer are working fine. It also worked fine 2 weeks ago. Does anyone have any suggestions. I downloaded the latest version of the HP Solution Center already.
-
which cluster service and how we use them in server 2003 sp 2 and 2008
Hello I want to know about cluster service, which is to use a Server 2003 sp - 2 and Server 2008 why we use Thank youKind regardsPatrice Hiren
-
Old computer BSOD when installing XP and randomly after installation
I'm repairing an old computer (5-6 years old) who has problems. Originally, it was full of viruses and was completely sunk, so I did a cleanup of the HD and reinstalled windows... However, increasingly, the owner complained to get BSOD once in a whi