XY graph in time real conspiracy

Hello

I'm creating a program of measurement of C-V-T using HP4284A RLC and Lakeshore 330 temperature via gpib controller. I'm of the temperature and voltage scanning. I need to have a simultaneous ground CV and I use an XY graph to display. My problem is when the loop set in the iteration next steps back without erasing the graph for the scan again. Can someone please help me find how to clear the grap of old values each scan

Thank you

Jean-Marie

Hi odimuthu,

My problem is when the loop set in the iteration next steps back without erasing the graph for the scan again.

Usually, you would create another plot in the same graph for the next scan!

When you really want to plot the data in the current sweep you must delete the data stored in the passage records (aka feedback nodes) when you start a new scan!

Tags: NI Software

Similar Questions

  • analyze serial port hex data and graph time real conspiracy

    Hello guys,.

    am a newbie to labview and am currently working on my final project of the student, but I met a problem extracting the values of currents and voltage of hexadecimal string read to read the VISA stamp. I also want to throw the string header every time so that I can only process only the voltage and current hexadecimal string. My rope of the read data is attached. 0023-0034 0045 0132 AA55 AA55 AA55... Where AA55 is header I want to throw. The following 2 after the header bytes represent the tension, while the 2 bytes represent the current. After 6-byte header (AA55) appears again.

    So far, I read the data read as attached VI visa, and I would be recognizing all assistance to extract successfully, only the voltage and current values every time the (AA55) header is read to raw data. I have read several forums observation about the covers this topic but none seem still a click. Thank you once more!

    The VI am working on is attached and some failures in the print screens.

    A framing error means that something is wrong with your string of bits 1 and 0 s, coming from your equipment.  The start and stop bits are not where they are supposed to be.  Check all your configuration settings set to ensure that they match the device.  Baud rate (230 400 seems quite high), stop bits, data bits, parity.  Something is probably wrong in there.  That or if you have bad cables or electrical noise interfere with transmission.

    Why is it you are emptying the receive buffer?  Which is almost never necessary and could actually cause you to lose data or start the synchronization of your data once you've established.

    I don't know what you're trying to do in this while loop inside.  That looks nothing like what I was describing.

    See the attached VI.  I have not fully tested (after all, I do not have material sending me data).  But it should give you the idea.

  • How to create a graph in time real LabVIEW 6.1?

    I am new to programming in LabVIEW (6.1). I wonder to create a LabVIEW interface that can operate the multimeter Keithley 6487, allowing us to apply a voltage and nth measures. With the measures that we have create a chart (V curve i) I find the XY graph, but it only allows to send all the measures at the same time (indexing) to generate the graph and not whenever we take the action so the graph build inn in real-time. I need to know how to create a chart or change the XY graph, so I can generate the i - V curve with each step we take in real time. Whenever we take the action and not once the program ends. Thanks in advance.

    You must place the graphic inside the loop and the use of shift registers to accumulate the X and Y in the form of tables. I do not have 6.1 right now in the process of execution, but it would basically look like this:

    Note that the above is for demonstration (the code is in fact a greedy loop). You can consider putting Scripture on file inside the loop. In this way, if the program crashes, you will not lose your data.

    WARNING: Using table build as indicated above will result in continued growth of memory. If your program is running for a long time, this can become a problem. One thing you may need to watch must have a limit on the size of the array. I know there is an example of "Table of XY" comes with LabVIEW, and I'm sure that this is with 6.1. You should take a look at this example, which implements a fixed buffer for the data in the chart size. You should be able to use the VI "graphic buffer XY"directly in your code. "

  • Create a subfolder of bookmark in time real bookmarking a page in a folder that I created for a registered earlier does not work

    Create a subfolder of bookmark in time real bookmarking a page in a folder of bookmarks, I created a saved bookmark previously does not work.

    Previously on a Windows XP computer, I could choose the "select" option and create a new folder under the folder I chose to put my new bookmark. "." On this computer, the 'new folder' option is not clickable.

    I thought about it. Thanks anyway.

  • Get information about the physical location (serial) Visa (slot) in PXI time real (Pharlab)

    Hello

    I PXI system with controller time real (OS Pharlab) and many maps series (about 6 cards).

    The maps in the series are two different models, which each contain several (8431/8 and 8421/8) serial ports.

    And the COM Port enumeration mix and I would like to know the link between COM numbering where it is linked.

    I have already dealt with a few methods:

    1. I've tried using the node property of Visa but he cannot know which card port COM belong

    2. I tried to use the Configuration Library system and don't manage to get general information of the card and not what ports have this card.

    3 try to fill you with the VisaConf.ini, but discovers that ASRL and COM Auto-enumeration is the same.

    4. I tried to look in NISerial.ini, NISerial.dbs and NOR - RT.ini and did not find any help here.

    Application engineer or support suggest to look in the registry of the operating system Pharlab because it is windows based and material information must be stored in the registry

    Further explanation on the problem of PXI enumeration:

    PXI produce enumeration auto for the ports series (COM3, COM4, COM5...) according to the card slot, but when there is a mix of the two models of the system would then list a model (8431) from 3 to 50 (6 cards and 8 ports) and the other model (8421) 51 to 98. so if I have 8421 in 2 and 8431 slot number in the slot number 3 it would list 2nd slot COM59 to COM68 and 3rd slot COM11 to COM19.

    Why not just use NOR-MAX to manually configure the ports?

    The system is essential and can not be stopped for a long time and he operated by people who are not very technical, so the customer who wishes to be able to exchange business cards without futher configuration.

    Thank you

    Or Hirschfeld

    Application engineer

    SK-Electronika, Israel

    www.LinkedIn.com/in/orhirshfeld

    Solved and download the example of solution of community

    Get the location COM (Serial Port) and Port physical location in the chassis

  • QUESTION: SE 2012 data display returns to the time graph each time

    Hello

    I have SigExp 2012.

    If I try to add a data view and make a pledge of graphic style, thermometer, etc., as soon as I have the right up until it clicks, add my TC chain, the data view returns immediately to a graph time.

    In addition, even if I use the graph of time, once I added the signal, it only let me see the string in a table, a chart of time or a waveform graph.  Those are the only choices.

    If I use a graph of time or a band of waveform graph, it does not read the signal correctly, but I can not configure the data view, the way I want it.

    Is this a bug or I do something wrong?

    Thank you!

    This occurs when you try to change the display of a signal in its raw format "waveform".
    You must convert your signals in scalar format. To do this simply add an amplitude and levels step (under: analysis > measures Time-Domain). Drag this DC signal newly converted to a new chart and right click on the graph to change the display.

    Honestly, I'm not sure why raw waveform signals are inherently limiting viewing functionality, but in such cases, it is.

    You can also; According to the devices on which you use and the order in which you add to your DAQmx Acquire, some default signals step to scalar signals without having to convert.

    See the attached screenshot and you'll see how the icons are different between the waveforms and scalar signals.

    Hope that helps

  • using the module time real Labview in RTAI

    Hi all

    I want to use the module time Labview in RTAI real for real time due to its open source applications and very good performance. is it possible to make this work?

    If this is the case, can anyone introduce a single study of case or something similar to this?

    Cecile says:

    Hi all

    I want to use the module time Labview in RTAI real for real time due to its open source applications and very good performance. is it possible to make this work?

    If this is the case, can anyone introduce a single study of case or something similar to this?

    I don't think it's possible for anyone outside of OR. LabVIEW Real-time supports this time only Windows as host and as a target only material of National Instruments with specifically targeted OSes or the Pharlap ETS system on x 86 systems with hardware specific enough. Using RTAI as target OS for LabVIEW Real-time applications requires first a few changes on the time plugin real LabVIEW to support this new platform.

    None of the files in time real LabVIEW also created for either platforms OR running VxWorks or OS Pharlap, Pharlap ETS system woud be able to be deployed to a system RTAI, because they are not compatible. In the first place, you'd have to port the bunch of shared libraries that make up the time target real system running LabVIEW on one of these goals to your RTAI system which is in fact a whole new platform of LabVIEW you can create with a little effort from the LabVIEW source code. It's not really impossible for OR as most of the code LabVIEW is written platform completely independently, but it would be a combination of the parameters compilation for course LabVIEW Real-time, with the settings to produce time targets real LabVIEW VxWorks with some additional settings of Linux. Yet, it would be by far not trivial and some parts are actually hardware specific drivers that must be worn too and limit the possibilities of what RTAI material could serve even further. In short not something that would make any commercial sense NC because they invest a lot of resources with no opportunity to sell additional hardware.

    And hell freezes over up front release of NI LabVIEW source code in any form which gives access not - OR used to it!

  • Time real ADC/DAC for SMPS by using Labview and USB

    Hi all

    I asked the Sales Department of this same question, so here's a two-pronged approach:

    I am reserching a control algorithm for power switching, and so far, its performance simulations seem to be good.  Now, the goal is to implement the circuit from the experimental data.

    I've seen several NI USB DAQ boxes that seem to have the performance, I'm looking for (for example, the box USB-6211 a sampling rate and resolution I need).

    The control algorithm uses the following mathematical functions: add/sub/mult/div/exhibitor and derivative/integral.

    My question is this: is "strong enough" Labview take four-channel data 250Ksps, crunches the numbers in an equation and spits out the answer to an analogue on the channel, while time REAL?  I'm looking for a rate of analog output of ~ 100 kHz.

    Thank you for any suggestions you have!

    -Rick

    Hey,.

    So if you were trying just to perform an input or output, then the box USB-6211 would certainly be able to treat it as the machine clock could manage the inputs/outputs, no software. However, what you are wanting to do, basically a feedback system, he will have to avoid (at least to a USB device) because you need to be able to specify Active which is the output. So, for this reason alone and the fact that you want out of 100 kHz, this device and the USB devices in general will be not an option any what software you use, LabVIEW or otherwise. On another note, you want to make sounds more like live update, not in real time, which is more on the jitter. Bottom line, for these kinds of requirements, you might need to move to an FPGA card, something like the NI PCIe-7841R would work. It's more expensive, but for your needs, FPGA will be the only option and it comes down to the latency of the bus, but also the response time of software. With FPGA, as shown in the first scheme of the following document, you basically close your software through hardware loop.

    Basics of FPGA

    http://www.NI.com/white-paper/6983/en

    -Ryan S.

  • Lack of time real plug-in

    I have a project in real time using a 9074 cRIO chassis. The project opens fine on my desktop but when I try to open it on my laptop, a yellow triangle with an exclamation mark inside appears at the level of the chassis and don't see anything below the level of the chassis. If I right click on it, it just says: "the plug-in for the selected item is not installed on your system or the plug-in has a license has expired. I have installed all these elements on this machine:

    NIRIO1310f1

    LV 2013 SP1

    SP1 FPGA development

    SP1 of development in real time

    NIDAQ1400f1

    Don't know what else I could possibly be missing, don't remember installing something more on my desk? No matter what project I try to open, any project won't let me in time real access below the chassis level. If anyone knows what I could miss I would appreciate the help. Or if you need more information.

    Thank you.

    I installed NIRIO14f1 and my phone seems to work again.

  • Average displacement Subvi does not refresh the data in time real host VI

    Hello!

    I time real host VI that has evaluate the NI 9215 cRIO block data 9073. He takes analog data and calculates the phase shift. It works well with the connected equipment and displays the results. I need to get the moving average value of phase shift, so I add moving average Subvi, where main VI entries - new value (phase shift measured) and ms and output - average value of travel time. When I run real time host VI it gives me a single data and stop get new data from Subvi. It refreshes not even values measured in real time. So the problem somewhere in the accommodation, with sub - VI. How it can be solved? How can I get real host VI with the moving average value of Subvi update running time?

    Thank you.

    Your problem is that you have a loop that runs until you press the Stop button inside your Subvi.  If you try to use a Global Variable that is functional, you have a few things wrong.

    1. the loop should run only once.  A TRUE to the conditional stay Terminal wire.

    2. the shift register cannot be initialized.  That is how he can keep the old elements in a story.  Use a first call? with a case structure so that you only initialize the table of history inside the loop on the first time the VI is called.

    But if you really want to make your life easier, just use the PtByPt.vi mean.  NOR did all the work for you.

  • In time real CRIO - writing a file on a PC hard drive

    Hi all

    I am developing and application with the following hardware features:

    Time real cRIO 9004 target device

    HAVE cRIO 9205

    AO cRIO-9263

    and the following programming features:

    I run an FPGA VI to establish PID control where the reference signal generated in the FPGA and the real is an acquired signal through the cRIO 9205.  I also find target FPGA FIFOs host in order to pass the data from the FPGA to the application of the RT.  The time real VI will run in the 9004 cRIO processor.  Now, with the data from the FIFO I would write a file (regardless of the extension), in order to do more tests.  I did it but I don't want to use the local memory of the RT, instead, there will be a PC (hard drive) where I can place the file in order to write it (with data).  I'm not able to do so, as 1) I don't know how to call the PC hard drive and 2) I don't know what communication protocol fits better I want to develop a device to Windows Welcome.

    Nobody helps me?

    Thank you very much

    Enrique

    The cRIO-9004 unfortunately has USB, so you can not write on a USB Flash drive (which would be my first suggestion).  If you want to store the data on the host PC, you will need to write a simple TCP/IP client/server to send data to the host through TCP so that the host can receive and save to disk.  Façade of the VI may seem as it is running on the PC, but it's actually just show you data be listened to the target (you are not allowed to piggy-back on this same Creek).

    There are several examples of TCP/IP client/server integrated into LabVIEW.

    -Danny

  • Time real 8.6 and PDM

    Hi all

    Using a CRIO-9012 with time real Labview 8.6 and labview 8.6 and now that TDMS is supported and I am wanting to use it on my cRIO. Be a problem if... in addition to open or close tdms files still do not work on my CRIO even if time real 8.6 is installed. Attached is a simple vi which works on my PC but not on my cRIO, tried still more simple screw with on the CRIO tdms and it does not work. When I try to run the program on the cRIO I just lose the connection to the controller and have it reboot. It is likely to what I may have missed?

    Thank you

    Jevon

    I came across a question like this and found that the path of the file to open it TDMS must have a tiny 'c' as in "c:\". "instead of"C:\ ". »

    You will always get an error on the end, but the IO files works.

    Kurt

  • remove the pop up message "Waiting for in time real (target CompactRIO RT) to answer.

    Is there a way to remove the pop-up message "Waiting for in time real (target CompactRIO RT) to answer" what power is removed the cRIO or when the network cable is disconnected?

    Hey Danny,

    How did send you the commands to the Windows PC the cRIO? You use the remote FPGA host Interface?

    I've seen the pop-up dialog box when the LabVIEW project is not present.

    If you create a Windows VI that sends orders via shared variables or other network mechanism to a VI RT, which in turn controls your FPGA VI, then you should not ever see the popup you speak.

    This tutorial walks through creating an example of monitoring on cRIO with three screws as indicated:

    http://zone.NI.com/DevZone/CDA/tut/p/ID/11199#toc4

    This tutorial is an example of the use of a shared variable to implement a heartbeat, to determine if the cRIO is connected:

    http://decibel.NI.com/content/docs/doc-11046

    I hope this helps.

  • Execution of several executables in time real (.rtexe)...

    For PXI (or any embedded controller OR) several executables in time real developed in LabVIEW (.rtexe files) can work simultaneously?

    I'm almost certain that the answer is 'No', because the whole point of a RTOS is the code to be "as deterministic as possible", with the Jig and schedule reduced by removing items (such as "interference of the BONE") out of control or understanding of the developer.

    Pouvez, however, write a single RT executable that loads into two routines that work "in parallel".  If you have a multi core processor, you could book separate processors for two routines that should improve their independence from each other.

    We met a slightly different variant of this issue during the migration of code LabVIEW 7 to a LabVIEW Project "oriented" development (introduced in LabVIEW 8.x).  We used to have several different programs of LabVIEW RT who has used a code different on the PXI - when we ran the host executable, it loaded and run the appropriate code of RT (recorded in a .llb).  This works well with executable RT.

    What we developed was a system where we have recorded each RT executable as a routine named separately ( not Startup.rtexe) and set them (initially) to run as a startup.  When the host code runs, it queries the PXI for the name of the startup routine, and if it is not 'just', change us it on the PXI and make the PXI to restart.

    [In fact, don't really do us this way, that 99% of the time, we always run the same executable RT.  What we did do was to write a separate "define RT Startup" routine that we almost never executed, unless we "know" we run an earlier version or something like that.  This, in turn, tells us that the PXI is configured to run and what executable RT can be defined as startup, then makes the changes, restarts the PXI and exit.  The 'rule' is that if you change the executable RT, don't forget to change the back when you're done.]

    Bob Schor

  • That is to see in time real 4K in after, nvidia qaudro k5000 Titan Z or something else?

    That is to see in time real 4K in after, nvidia qaudro k5000 Titan Z or something else?

    My PC is X - 99, i7 - 5820 k, 64 GB, raid0, SSD...

    best,

    In it's current state given after effects is mostly from the CPU then graphics cards make little difference in performance. Adobe usually (but there is no guarantee) announcement of updates at NAB tends in a few weeks, so I would hold off buying new hardware, including expensive equipment, until you see the new requirements and dates for new versions of output.

Maybe you are looking for

  • Information / photo upload control

    I have a large photo collection (I use iCloud library and have used so far nearly 600 GB).  I keep the originals on my iMac and we have two laptops (MBA & MBP) and different phones and iPad all share the collection of photos. The photo sharing/synchr

  • HP all-in-One: alarming of the boos and screams

    For the last two days, when I boot upwards, pressing the switch on the top of the screen, the computer emits a series of boos, then screams, then more boos and shouts. It sounds very alarming. It is start properly, but must it be of these noises? I f

  • HP pavilion 23 touchscreen smart all in a single pc23 h050 upgrade RAM

    Should I buy a desktop or laptop computer RAM? Is it still important?

  • When my Colby MP3 music downloading, I get error or unknown format...

    When I sync music to my Colby MP3, it appears a black circle with a cross in the Center.On my device, the message appears an unknown Format. I checked to make sure that I download in wma or mp3. What is going on? Melissa

  • Netflix BDP-bx59 has stopped working

    If I look at you tube or cracking before netflix, netflix is trying to load, and then the screen goes black. I go back to the House or turn it off, and it's the same thing. The next day netflix will work if this is the first application that watch yo