Linksys Products

I have set up with linksys E4200, but it does not connect to my computer, the blue light showing but the link light will market

I want to use WAG54G2 as a simple router. I happen to have 2 of them. If I can make one of these work as a wired router via ethernet cable or even wireless I can save money on the router. Is this possible?

Hello I would like to know how to properly set up my old wag354g as a wireless access point. should I choose in the basic as 'bridge only' menu or 'rfc bridge "? WAG354G will be linked by wire and wireless on laptops with b/g of food. TIA.

How storage works with a WAG320N device via USB if I use a Ubuntu 10.04/10.10 and al? Makes it look like an FTP site or can I just use it as a shared folder accessible if the normal folder directory structure from any machine on the network. Does any

I bought a camera (ver. 3 - en) WRE54G refurbished. Just before the installation, I was able to connect to my wireless network, internet access, etc. So I ran the installer for the WRE54G to my laptop, which failed because the installation program co

Hi, I just bought this router today and I am faced with this strange problem. The telephone line when connected to my modem works fine but when I connect to the router and set it up so I don't see the comin DSL light. Nothing happens. I tried to CONN

Hi, what it is. I am installing a WAG160N to my Win 7 32 bit Pro system and I have a red internet light and im not getting on the internet. I know that my internet is ok, because I reinstalled my BT home hub to get on this forum. Anyone know what is

When they will move a cable modem and the router which can be reset or restarted or rebooted since my computer?  Even if exercise can be good for me, I'm tired of having to take the time to unplug my modem and router to get my interntet work, have yo

G ' Day, I bought a modem router WAG160n one a WUSB600n. I have set up my internet protocol for my local ip settings, but the parameters keep returning to "obtain an ip address automatically" it never happened with any of my cable modems. Can someone

Im trying to put in place the WAG325N I have DSL connection but no internet connection whenever I try to connect to the internet internet light only flashes red for a few seconds then turns off. all ideas

Hi all, ok before I completely remove all of my hair, I thought stop by here and ask the volume for you all with the hope that someone can track down the problem. In short I am configuring a 'Gateway to gateway' vpn tunnel between two sites, I don't

I have a new WG54G2 to replace a netgear DG834G wireless defective. I did the necessary configuration changes to my ISP as follows: Encapsulation: PPPoAMultiplexing: VCType of QoS: UBRPCR: noRCS: noneAutodetect: activateVPI: 0VCI: 38DSL Modulation: A

I bought this model and use it to connect 2 office units and a playstation 3 through the ether, but also a laptop via the wireless link. using only the ps3 works fine, using only offices very well works. problem using laptop computer while sharing th

I am currently struggling with a MRC WCG200. Wireless-G is not quite cut it anymore in terms of scope and power of the signal. I was contemplating daisy chaining a Linksys WRT310N to it and turning off the G in the modem. Someone had a bit of luck wi

I just bought a WAG160N, no problem of implementation and it seems to work fine. I tried to reach it from the internet ('Block anonymous requests' is not selected) when I type the address using the port 8080, I get a right page returns with three cha

I have a netgear wireless router which is dead. However, I've never had any problems with the media file sharing with WMP 11. After this router my media sharing file does not work. No devices appear at all. I use an Archos 605 PMP I have the latest f

Hello.   With about 4 off all 5 IPS that my ISP dynamically assigns to the WAG325N, I find that I can't get ftp access to a web server provided by another company.  All the problematic addresses begin with the same number, and get round it I have to

Hallo, I have a Lexmark X 3330 MFP and a PSUS4 print server. Driver installation works very well and I followed the instructions exactly. BiAdmin diagnostic tool can find the printer as well as the Web interface. But if I want to print a testpage "no

After installing linksys printserver wpsm54g with my printer dell aio 944 on vista, vista said it still need the installation driver for wireless printserver even if I finished the whole plant without problem.

Why can't I save a router with Linksys WAG160N? Is it because these devices are not sold in the United States?