Linksys Products

Just bought this camera today and very disappointed, as I've been with several of my recent purchases of Linksys. In any case, try to make the best of it... after hours of messing around to configure and test, I found that the RE-1000 is in 802. 11 b

I have a circa 2011 Linksys RE1000 running fw 1.0 I upgraded to Linksys RE1000 fw 1.5 (v1.0.02 build 1 14 February 2012) and that seems to work without any additional problems. I note that there is a fw v2.0 If I try to use fw v2.0 to upgrade, I get

Hello I have a router g 2Wire in my basement and a bad signal to the 2nd floor of my house. I bought and implemented my RE1000 and now it's fantastic, I have an excellent signal on the 2nd floor of the House. Problem: in my basement, if I want to con

I had problems with this range extender for several days now, and it's very frustrating. I have a router Sagemcom F@st 2864 (connection Hub) with Bell Canada. The diffuse Router 2.4 GHz with Auto B/G/N, channel 11, 20 Mhz bandwidth, be able to pass 1

Hello! I got the router WAG160N for almost 1 month now and I never had to work more than an hour without problem. It seems like it to reinitialize all 10-15 minutes. I tried this medicine: update firmware, factory reset, reconfigure the router, EVERY

Hello I'll try to find how to connect to the stream mpeg4 WV2300 using the VLAN, Mediaplayer or similar. Also, how do I connect via RTSP. This old thread Control of WVC2300 covers a few orders, but still lack a lot of commands to remotely control the

Hello 1 - my modem is WAG54G2, I updated the firmware to the latest Firmware Version version: V1.00.19 on the web site (Because I read a lot of things that Linksys modem can create problem on the L2tp traffic, they were advice updated firmware) 2. wh

I have a WAG54GS and I also have a Linksys firewall device, separate units. My PC are behind the Linksys firewall that has a port WAN1 allowing plug a router device. Currently the WAG54GS is factory with NAT and active firewall settings. I want to us

Not very irritable with it - I will try to explain the existing facility and the requirements in the simplest possible current configuration: each wall jack in my (dorm) room has an ethernet jack that I connect to my laptop and wait the connection to

My ISP technician could not configure IPTV on Cisco WAG310. -Internet is OK but IPTV in bridge mode did not work. I contacted the Support technique Linksys at 2010-08-14 19:35 (Incident: #) don't-> any suggesstion The second time at 14/08/2010-21:50

We set begin to use a new supplier of internet services by cable. This provider requires you to use their modem. My question is, 'We already have a LinksSys WCG200 cable gateway', will be able to simply use the router function of cable without the bu

Using XP Home Edition SP3 + all IE8 Inc. updates...   A couple of weeks at least, I discovered that WG354G does not, restart have you tried all sorts, repugnant a few to list everything I tried--would put everyone to sleep, (I'm good at that)! When I

Hello! Where can I see the status line in WAG-320N? States such as Type of latency, SNR Margin WE / DS, mitigation of the U.S. line / DS, eat / DS etc. I found just downstream and upstream of the situation/access DSL rates. Sorry for my English.

Hi, I tried to record my modem/router, since I bought it but my S/N keep rejected as incorrect. I also tried through one of the Linksys online support and they do not have too. What is the problem please? Gambas

I bought a Monday wag320NNot that impressed with the signal strength wireless - whereas it is better than my 2003 D-Link, but it wasn't. Also, the wireless signal varies a lot... I tried different channels and currently set to CH1 Also, the USB hard

Hi, I have wvc54g v1.1. It has worked well. It does not work after download 1.21 firmware. I plug in the router, but I can't. I have reset over and over again. I can't reach the camera that I can't work on it. How can I solve this problem. Thenks...

I bougth one annex-B WAG54G2, because I use ADSL on ISDN (residing in the Luxembourg) and my internet provider pointed out, I'd need to buy a modem ISDN. I plugged the gray cable to the modem of the ISDN splitter Jack like I did with my old modem (a

Hello my client has a WAG54GS router and I just bought a WRE54G range extension to help its wireless network coverage. But I have since views information here and there on the possibility that these two devices are incompatible with each other. Could

Hello I am trying to update my firmware using the files provided on the linksys site. I have entered my serial number of the router correctly and chose the model of the good version (v.1.1) and downloaded the firmware file. I have connected my router

Hello After AC power interruption, I tried to turn on my router Linksys WAG300N, but he won't start properly. I will describe what it looks like and what I've tried: I push the power button / stop, all 4 Ethernet LED simultaneous light for about a se