15 - f039wm has no power after upgrade memory (or disk).

Similar Questions

• Satellite L100 113 starts slowly after upgrade memory

  Hello

  Toshiba Satellite L100 113 PSLA3E-02401JRU starts slowly after upgrade memory with Kingston KTT533D2-512 (512 MB) of memory.
  When I press the 'power' button, it flashes, starts the fans and HARD drive several times. Then it shows BIOS start messages by memory full 768 MB and starts Windows XP without a problem.
  This behavior is noticed only after "shut down."
  It does not happen with "restart".
  What can I do to eliminate this long "attempts" to start my laptop computer?

  Thank you
  Novomir Kovalenko

  Hello

  This problem appears before upgrade memory?
  Have you used exactly the same memory modules?
  If this isn't the case, then perhaps there are a few compatibility issues.

  Usually, after the insertion of the modules you must enter the BIOS and then save the settings. Please it and eventually the laptop will start without any problems.

• Satellite L50 - A - 1 5 PSKK6E does not start after upgrading memory

  Upgrade memory L50 - A - 1 5 pskk6e

  I have a memory ddr3 4 gb 1rx8 pc3 - 12800 S-11-12-b2 hynix and I tried to add another memory
  memory DDR3 4 gb 1rx8 hynix pc3 - 12800 S-11-11-b2, but it does not boot up the laptop.

  I tried to mount only the new but it won't start.

  Some ideas?

  I think that it s you already know that this Satellite L50 - has - 1 5 would support max 16 GB of RAM (2 x 8 GB)

  But why, box for computer laptop doesn t is very simple: the new modules are not compatible.

  I found modules recommended by Toshiba.
  These are:
  8GB DDR3L - 1600 PA5104U-1M8G
  4 GB DDR3L - 1600 PA5104U-1M4G

  Both are made of Kingston and the specifications are:

  Memory speed: 1600 Mhz PC3-12800
  Capacity: 8 GB (1x8GB module)
  Pins: 204 SODIMM
  Type of RAM: DDR3 SODIMM
  Verifying the integrity of data: non ECC
  Specifications:
  Latency (CL) CASES: 11
  Voltage: 1.35v

• Firefox 4 beta too slow / crashing after upgrade memory?

  Hello

  my beta firefox started crashing my whole system yesterday and only noticeable change I did was upgrade memory of 3 to 4 GB of RAM...

  I tested my system widely and it works very well until firefox is started, after that, the system started crashing and takes forever to be reactive. I uninstalled and reinstalled firefox, tried running without addons, I tried to close all the tabs and all Eske I remembered... still no luck.

  I am desperate because I really wanted to keep this beta on my computer, and cuz is a new facility, I can not install firefox 3.6 on side by side, I only have an option 'upgrade' on the installation wizard...

  What can I do to fix this?

  Thanks in advance!

  The steps to troubleshoot and diagnose problems of Firefox would say you always try in questions to troubleshoot Firefox in Safe Mode of course some additional software may conflict, it is even more likely if you are using a beta version of firefox and probably the beta or alpha some of the addons or plugins.

• Cannot get any sound on my speakers after upgrading memory

  just updated my computer by adding more memory but I can't get any sound on my speakers

  Hi RawleHouston,

  Thanks for posting your question in the Microsoft Community.

  I understand that you can not get any sound of your speaker after upgrading your memory. Correct me if I'm wrong.

  I imagine the inconvenience that you are experiencing. I will try to help you in the matter of fixing.

  To help you suggest several steps to solve the problem, I would appreciate if you could answer the following questions:

  1. What is the brand and model of the computer?

  2. you receive an error code or message?

  Please follow the methods and mark the question below:

  Method 1:

  Step 1:

  Run the Microsoft Fix It from the link below.

  Diagnose and automatically fix the audio problems and audio playback:

  http://support.Microsoft.com/mats/AudioPlayback/

  Step 2:

  Follow the steps in the link below.

  No sound in Windows:

  http://Windows.Microsoft.com/en-us/Windows/no-sound-help#no-sound=Windows-Vista&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Method 2:

  Follow the steps in the link below.

  Tips for solving common audio problems:

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-sound-problems

  I hope that the information above helps you, and if you encounter any problems on Windows, please do not hesitate to post your request here on Microsoft Community, we will be more than happy to help you.

• A6745f crashes on startup after upgrade memory.

  Try to improve this machine with 16 GB of memory. A row of 2 x 4 GB sticks work great, but when I try to put in the last 8 gb, it freezes just after the display of the memory on the opening screen. It records all the 16 GB is there, said then "press F10 for bios' and hard locks. I have to pull the plug.

  I swapped the sticks around without problem. The MB watch news that he supports this quantity of memory in a 64-bit environment.

  BIOS Rev - Phoenix 5.13

  MB - MSI - MS-7548

  Running Windows 7 Professional 64 bit.

  Kilroy14 wrote: I guess that the MB does not have the 16 GB literature although not? I guess this is no longer supported. If anyone has experience with this, please let me know. Thank you all!

  Hello Kilroy14, I checked the specifications of your system, which can be found here , and it does not show the system supports up to 16 GB of memory system.

  I also found the Crucial or Kingston memory did not 4 GB memeory modules listed for your system.

  Another provider of memory has indicated that some Kingston memory would be only recognized as a total of 8 GB even though there were 4 x 4 GB modules installed.

  It is not, as you suggest, this model can not supported 4 GB modules when installed in all memory slots.

• Boot Camp has stopped working after upgrade to Yosemite

  Hi all

  I also lost Boot Camp after upgrade to Yosemite. I tried to recover by following the instructions on this forum but did not.

  Issues related to the:

  1. can I get it back? See some of the data below.

  2. otherwise, I can create a new training camp after the recovery of wasted space?

  3 is it better to first upgrade to El Capitan?

  Thank you in advance!

  ➜ ~ diskutil list

  / dev/disk0

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * 1.0 TB disk0

  1: disk0s1 EFI EFI 209.7 MB

  2: Apple_CoreStorage GB 950,5 disk0s2

  3: disk0s3 Apple_Boot Recovery HD 784.2 MB

  4: Microsoft database 32.0 GB disk0s4

  / dev/disk1

  #: NAME SIZE TYPE IDENTIFIER

  0: Apple_HFS BrontoSSD * GB 950,1 disk1

  Logical volume on disk0s2

  90BC997C-0C7C-40FB-896D-973BC192A123

  Unencrypted

  ➜ ~ list cs diskutil

  CoreStorage groups of logical volumes (1 found)

  |

  + Logical Volume - Group 46320040-2E97-49D9-A652-87CBA72E637D

  =========================================================

  Name: BrontoSSD

  Status: online

  Dimensions: 950509715456 B (950,5 GB)

  Free space: 18956288 B (19.0 MB)

  |

  +-< physical="" volume="">

  |   ----------------------------------------------------

  |   Index: 0

  |   Disc: disk0s2

  |   Status: online

  |   Dimensions: 950509715456 B (950,5 GB)

  |

  + -> 14BD334A-53BE-4C89-949D-2E8E5EF30A59 family of Logical Volume

  ----------------------------------------------------------

  Encryption status: unlocked

  Encryption type: no

  The conversion status: NoConversion

  Direction of conversion: - none -.

  At encrypted extensions: No.

  Fully secure: No.

  Password required: No.

  |

  +--> Logical Volume 90BC997C-0C7C-40FB-896D-973BC192A123

  ---------------------------------------------------

  Disc: disk1

  Status: online

  Size (Total): 950138437632 B (950,1 GB)

  Conversion progress: - none -.

  Reversible: Yes (no required decryption)

  Name: BrontoSSD

  Volume name: BrontoSSD

  Content indicator: Apple_HFS

  ➜ ~ sudo TPG - vv - r show/dev/disk0

  Password:

  See the TPG: / dev/disk0: mediasize = 1000204886016; SectorSize = 512; blocks = 1953525168

  See the TPG: / dev/disk0: MBR suspicious to sector 0

  See the TPG: / dev/disk0: Pri GPT to sector 1

  See the TPG: / dev/disk0: GPT Sec at sector 1953525167

  start index size summary

  0           1         MBR

  1 1 Pri GPT header

  2 32 table GPT Pri

  34 6

  40 409600 1 part TPG - C12A7328-F81F-11D2-BA4B-00A0C93EC93B

  409640 1856464288 2 part TPG - 53746F72-6167-11AA-AA11-00306543ECAC

  1856873928 1531680 3 part TPG - 426F6F74-0000-11AA-AA11-00306543ECAC

  1858405608 32621336

  1891026944 62496768 4 part TPG - EBD0A0A2-B9E5-4433-87C0-68B6B72699C7

  1423 1953523712

  1953525135 32 table dry GPT

  1953525167 1 dry GPT header

  ➜ ~ sudo fdisk/dev/disk0

  Disk: geometry / dev/disk0: 121601/255/63 [1953525168 sectors]

  Signature: 0xAA55

  From end

  #: cyl hd s - cyl hd s id [Start - size]

  ------------------------------------------------------------------------

  1: EA 1023 254 63 - 1023 254 63 [1-409639]

  2: AC 1023 254 63 - 1023 254 63 [409640-1856464288]

  3: AB 1023 254 63 - 1023 254 63 Boot Darwin [1856873928-1531680]

  * 4:87 1023 254 63 - 1023 254 63 [1891026944-62496768] VS NTFS

  You must run Testdisk. Have what you tried so far?

• Why a sql statement has become slow after upgrade to 11g database

  Hello
  
  My previous version of the database is 9I and any sql statement are well-developed.
  but after upgrading to 11g database, a sql statement become slowly.
  
  My senior dba friend told me there are a few different calculating methods from 9i to 11g.
  is any body can explain this different methods from 9i to 11g, and what should be attention to calculate at what level 9i to 11g. I thank.
  
  Sean

  The administrator of yours is correct. What he meant, 9i, the works of the optimizer with different formulas and 11 g, there are different formulas. PS this sometimes causes when you upgrade from 9i (or even 10g too), analyze the queries that worked with RBO in 9i perfectly and used indexes, all of a sudden they stop using it because the CBO think not that this is a good choice. It would be too difficult to put formulas here by anyone, but what I can say is that to buy a book.
  http://www.Amazon.com/cost-based-Oracle-fundamentals-experts-voice/DP/1590596366

  And practice on 9i, 10g and 11g. It would say a lot of formulas used by oracle.

  HTH
  Aman...

• Satellite P50 - B - internal error power after upgrade to Windows 10

  After the upgrade to Windows 10 and after reboot, I got Internal_Power_Error and laptop restarts automatically.
  After signing, get the same error of internal power and the repetitions of the process.

  I contacted Toshiba Support and they did NOT have a fix for this problem.

  The power driver should be updated but no ETA on when the fix will be available.

  Be wary.

  This does not resemble Toshiba problem. The issue (error message) appears due to AMD graphics card driver compatibility issue.
  This seems to be a problem with all computers with a particular AMD GPU.

  Probably the 10 Windows take the old driver (catalyst process) is not fully compatible and the solution could be:
  -graphics card ATI catalyst unisntall
  -updated the driver... (try to download the drivers Win10 for AMD driver AMD site)

  You should be able to update the drivers for the GPU in right click Device Manager the GPU.

  In case the 10 Windows will not find an AMD update, it must simply wait and use the internal Intel GPU that is part of the CPU. This occurs after the AMD/ATI driver has been uninstalled.

• Satellite M30X-122 does not start after upgrading memory

  Hello

  I want to upgrade the RAM in my Satellite M30X 122. Correctly my NB contains 2x256MB.
  I bought a GB 1 333 MHz. Cl2.5 module PC2700 (corresponds to the former, but more grand ;-)))
  Now I build in the module, but after the build-in system is dead.
  It doesn't show anything on the screen (after pressing the button one)).

  Does Anyboby have some tips?

  Thank you very much
  Peter

  Hello

  Toshiba has recommended the use of these memory modules:
  PC2700 256 MB (PA3311U - 1 M 25)
  PC2700 512 MB (PA3312U - 1 M 51)
  1024MO PC2700 (PA3313U-1M1G)

  Well, the size of 1024MB should be compatible. In this case, it s not a module size.
  Have you tried to get into the BIOS? BIOS recognizes the memory module?
  Maybe the module is broken?

  In my opinion, you should check if the module memory works on a different unit. If this module works correctly on another unit if your M30X doesn t support this module of memory and you need one another.

• R50E does not start after upgrading memory

  I tried to upgrade this laptop from the factory of 512 MB to 1.5 GB. I got a Kingston 1 GB DDR - 333 SO-DIMM, but after I installed it, the laptop does not turn. Only the power led is lit.

  I don't know why this happened, because all tests indicate that it should work.

  1. the new stick is ok. I tested it in another laptop and it worked. I also cleaned the contacts with isopropyl alcohol.

  2. the memory locations are ok. The old memory works in each slot.

  3. I tried to install the new one stick in a slot and it did not work.

  4. This update is officially supported by record of IBM and BIOS is up to date (v2.1, December 2006).

  Unless I'm missing something there is a confusing question. Unfortunately, I don't have an another 1 GB DIMM to test with.

  yehuda1 wrote:

  TBut I don't think it's a matter of density. something fundamentally wrong with this system. I just discovered that I can not upgrade the memory somehow, even not with a stick of 256 MB. The system starts only with the current key.

  OK... This is not good, but I have to tell you that...

  I guess it's time to throw the boy part of retirement and move to a new machine...

  Good luck.

• Performance degrades in Probook s 4540 after upgrade memory

  Hello. I installed recently in my memory modules two Kingston Probook4540 (2x8gb ddr3 1600 CL10 240 pins). Since I did this, Windows 8 is much longer to start and performance dropped considerably. But, if I put only one of the two modules, or the original 4 GB module, Windows runs at normal speed.

  I think it's a BIOS problem, as I see this error even on laptops the other brand, for example here
  http://superuser.com/questions/379970/laptop-is-incredibly-slow-after-RAM-upgrade
  
  I have the latest BIOS version available (F31 26-SEP-2012).
  
  Thank you.

  In case anyone is still interested in this topic:

  It is a solution that worked for me.

  It is not an official solution or supported.

  I used the laptop intensively in the described configuration and had no problems that I can relate to the configuration of the memory.

  Deduct from a 256 MB RAM memory available for OS could eliminate the problem for some processors.

  The solution runs on:
  -HP 4540S

  -i5 - 2450M

  -AMD/Intel switchable graphics card

  -16 GB OF RAM

  -Bios F.42

  It might work for other processors.

  Under Windows, you should deduct 256 MB of RAM, using EasyBCD or a similar tool.

  Instructions for EasyBCD:

  Under Advanced settings/developer set 256 under "MiB deducted from physical memory", save the settings and reboot.

  In Linux, the "mem = 17G" value in the boot of the kernel settings (actually deducted 256 MB).

  Edit:

  On Windows 7 and later versions, you can also use the following instead of EasyBCD:

  bcdedit/set {current} removememory 256

  (Run the command at the prompt with administrator privileges and restart).

• Satellite C660 - black screen after upgrade memory

  Can Hi anyone please help

  try to upgrade the ram on my C660 account currently 3GB - talk to Toshiba and they told me the type to get and said im running 64-bit windows, I could go up to 8 GB - then bought the following

  DDR3 1066 MHz sodimm - x 2@4GB---de MyMemory.com (£64)

  When I mounted it and turned on the screen is all black.
  Anyone has any ideas please im in the middle of my assignments aaaaaahhhhhhhh!

  And any help would be really appreciated

  John

  Hello

  Looks like not compatible or faulty module.
  You can start the laptop properly using the old modules?
  If Yes, then the new memory should be replaced by another.

  I recommend modules Kingston I think they make good quality

• NB305 - does not start after upgrading memory

  Have just bought 2GB memory update for Toshiba NB305-106, and it does not work. Machine unbootable - started 1 GB module.

  Just read a post on memory upgrade problems - different users having problems and they used Crucial memory without any problems. -Is it true?
  Anyone got an advisor?

  Hi ian123,

  If the boot netbook doesn't, additional memory module which means this module is not compatible and you need another.

  It would be interesting to know which module you are buying exactly and what specs it has.
  Can you post this information?

  In General, I have good experience with the modules of Kingston

• Satellite L100 113 does not start after upgrading memory

  Hello.

  Our Integrator bring to our company KVR800D2S5, but laptop memory modules does not start :(

  I read manual - this laptop supports 533 PC4200 memory modules.

  But SO-DIMM 533 MHz will be delivered in one month...

  The memory modules, we can install to Toshiba L100-113?

  Thank you.

  Hello

  I think that the laptop does not power upward because of a barrette memory faulty or not fully compatible.

  Please visit this memory 3rd party:

  [Memory for Toshiba Satellite L100 113 | http://www.orcalogic.co.uk/asp/prodtype.asp?prodtype=22360&ft=m&st=3]

  As you can see Satellite L100 113 memory can be upgraded up to 2 GB (2 x 1 GB) and you must use the DDR2 533 MHz (PC2-4200) 200 - PIN SODIMM

  Concerning