15K067NZ HP Envy: taken 3 USB of my laptop HP Envy 15K067NZ / HP Laserjet P1005 Printer requires 2 USB

Similar Questions

• my HP envy 5330 takes forever to print, or not at all

  Hello

  I have a HP Envy 5530, which do not print most of the time. Sometimes it will print but often it will say: it is printing then leave after 10 minutes. Sometimes it will print a half page.

  I set up to connect to the router but have also tried a usb cable, but there is no difference

  Any ideas?

  Thank you

  Jono2

  Please provide the following information if anyone can help including:

  The printer model - done

  Complete and detailed problem description-

  Operating system on the computer (including the revision of the service pack)-

  Connection method - Direct wireless, wireless, wired LAN, USB? -

  Brand and model of router and modem? -

  Error messages - on the screen of the printer or computer, no matter what flashing light patterns? -

  Do you think the printer is going to sleep and can't wake up? -

  If wireless, in the event of problem, what is the status of the blue wireless light on the printer, active, disabled or flashing? –

  Say, download and run printing HP and Scan doctor, what - what?

  http://support.HP.com/us-en/document/c03286146

• HP Envy 4500 All in one Printer

  Hello, I have a HP Envy 4500 all in one printer that is only a year and have had many problems with.  Recently, when I turn it on, it displays an error code; 0XB3F4F4F8. I have not found what means this error code. ? I tried to unplug and then turn on to get the Welcome screen, then it said error code and does NOT stop automatically. I have to unplug it to stop it. Any help would be greatly appreciated!

  Hi!, jenwad87:

  Refer to the HP printer... http://support.HP.com/us-en/product/HP-envy-4500-e-all-in-one-printer-series/5304875/document/c00489814

  Please, contact with the help of HP, of... http://support.HP.com/us-en/product/HP-envy-4500-e-all-in-one-printer-series/5304875/model/5304876/troubleshooting

• ENVY 5530: 5530 WANT wireless printer stop halfway through the page. Memory problem?

  Good afternoon:

  I m encouraged to print from an HP laptop pavilion15-N228SS wireless (WIFI) connection. Printer ENVY 5530 beggins to print but stop abruptly in the middle of the page, or just the printing of the page if there is an image.

  I think I have to give some more memory to the printer but if I Don t know how to do.

  Thank you very much.

  Take a look at this HP doc .

  You should also consider upgrading to 8.1

• HP ENVY 4507: HP ENVY 4507 can this label printing

  HP ENVY 4507

  Take this printer by printing labels please, if someone can help me please

  Thank you

  A quick response would be apprieciated as only bought last week, and the seller said he should do as most printers have this option. Have tried and can't see any reference to print labels, will resume and get a refund.

  It's OK now found how do labels that I need, but doesn't show do not how to make on this printer and came back to a Web site that provides labels and they showed me how to do it using Word.

  Thanks anyway

• OfficeJet 4500 G510n-z, HP Envy, Windows 8.1, cannot print full page color or b photo

  OfficeJet 4500 G510n-z, HP Envy, Windows 8.1, cannot print full page photo color or b & w, prints the text of the entire page.  Tried several programs with the same result.  A run all diagnostic tests, Test the printer prints full page, but HPdr test does not completely print page.  Pilots to consult.  Where should I go now?

  Hi there @DFK43 , welcome to the Forums!

  I saw your post and I would like to offer my suggestion for the problem you are having with printing photos in color or black and white.

  First of all, to perform all the updates of Windows, select those optional too:

  Windows Update - ' do I need to check the updates?

  Try printing now, if the problem persists, try:

  1. uninstalling the printer software

  2. restart your PC

  3. Reinstall in 2 ways:

  (a) HP printer install wizard for Windows

  (b) HP Officejet Full Feature software and driver

  Best wishes

• Windows 7 think no driver USB there is for the HP LaserJet 1200 printer

  When I plug my HP LaserJet 1200 printer in my Windows 7 laptop via a USB cable, the correct driver should install automatically, but it does not work.  The message error is "HP LaserJet 1200 printer doesn't have a driver', which is not true.

  This driver used to work properly on Windows 7.  It is suspected that HP could inadvertently, recently broken the driver.  Do you have someone at HP, or at Microsoft, typo or mistranscribe the string 'HP LaserJet 1200' in a version of the driver, or in a catalog that refers to a newer version of the driver?

  To be clear: I is not a smart solution that puts my system in a strange state, I do not understand, or want to try different things that might work, but (as far as I know) could corrupt vaguely a few hidden files or reference system.  My system is now in a clean and orderly condition.  I wish him stay that way.

  I'm looking for the standard driver auto installation correctly according to the standard method, as it should.

  Since the first meeting of the problem, I erased from my hard drive and reinstalled fresh (not just recovered, rescued or updated, but wiped and freshly reinstalled) my operating system to Windows 7.  It made no difference.  Therefore, the problem seems not to be a problem with my installation.  It seems rather to be a problem with the driver, a catalog that refers to the driver or something of the sort.

  We realize that the HP LaserJet 1200 is a pretty old printer, for which we could expect little support.  Despite this, would be the person at Microsoft, who knows printer drivers, check that the "HP LaserJet 1200" string not inadvertently has been misspelled or mistranscribed in a recent version of the driver, or in a catalog that made reference to a recent version of the driver?  As I said, this driver used to work.

  If the driver is listed, then you don't have to go through the company if in the update catalog. That's the good news.  The bad news is that I do not understand why it has not installed.

  Go to devices and printers.  If there is anything listed in the category 'printers and faxes', select it.  Once you select an item in this category, you will see a 'Print server properties' button at the top of the printers and devices window.  Click on this button.

  If there is nothing in the category 'Printers and faxes', you will not be able to get the print server properties button, so instead, open a command prompt window (click on the start ORB, type cmd.exe and press enter), type the following in the black command prompt window and press ENTER:

  printui/s/T2

  Whatever it is, you will end up the "Print server properties" window, like this:

  

  I guess that you will NOT see a list for the Laserjet 1200.  Before you add it, however, click the "Ports" tab  You have a Port which is presented as "DOT4_001" (the number may be different at the end)?

  Unplug the printer if it is connected.

  Back to the tab drivers, click "Add" and you can start the Add Printer Driver Wizard, which is very similar to add an assistant of the printer that you saw earlier.

  Click on 'Next' and check the box next to your system - x 64 for 64-bit and x 86 for 32-bit.

  Click "Next", select "HP" and "Laserjet 1200 Series PCL 5" and click "Next"

  Click 'Finish' to close the wizard

  You must return to the Ports of the print server properties tab and now the driver for the "Laserjet 1200 Series PCL 5" should be included in the list

  Close the print server properties window

  Restart the computer

  Connect the printer.

  It installs correctly now?

• HP Envy 7640: Wizard of the printer does not - HP Envy 7640 UDCString_UDCName error

  I am able to print, scan, copy and fax on my HP Envy 7640 printer very well.  However, when I click the icon HP Envy 7640 for the Printer Wizard just to check my ink level, for example, I get a script error.

  An error has occurred in the script on this page

  Online: 42

  Tank: 17

  Error: Unable to get the "UDCString_UDCName" reference to undefined property or null

  Code: 0

  URL: file:///C:/Program%20Files/hp/HP%20ENVY%207640%20series/Bin/HPSPProgress.hta

  Do you want to continue running scripts on this page?  YES NO

  Before I can even click on YES or NO, the screen changes to show the following. There is a yellow triangle with an exclamation mark next to this error:

  HP Printer Wizard

  Series\Bin\UDC_files/UDC_Main.JSON HP HP ENVY 7640 C:\Program

  Series\Bin\UDC_files/tasks.JSON HP HP ENVY 7640 C:\Program

  Series\Bin\UDC_files/URL.JSON HP HP ENVY 7640 C:\Program

  Series\Bin\UDC_files/localize_1033.JSON HP HP ENVY 7640 C:\Program

  When I click OK, I get:

  HP Printer Wizard

  Stop running this script?

  A script on this page slows down your web browser to run slowly. If it continues to run, your computer may become unresponsive.

  I connect to Internet through LAN.  My printer is connected to my pc through USB.  I do not use of wireless.

  I did not any changes to software or driver.

  I read through many solutions in this forum and tried several.  I disabled my firewall and antivirus first.  None of them have worked. I tried the SCLiteFix_299026.exe, the missing persons files difficult.  Did not work.  When I try to uninstall the printer and reinstall, I can't do that either.  I get error 2503 and 2502.

  I want to just my printer wizard to work and have been unable to find a solution.

  Maybe not all of these steps were necessary, but here's what I did and it worked! :

  (1) open HP Support Assistant icon on desktop.  It is a white question mark in a blue circle.

  (2) HP Support Assistant should show all HP devices.  Find your printer and click on UPDATES.  (Mine had no updates pending, but I clicked on UPDATE anyway)

  3) click on Diagnostics and tools

  4) click on HP print and Scan doctor.  Select your printer and click NEXT

  (5) you will get DIFFICULTY PRINTING and SCANNING of DIFFICULTY.  I chose the DIFFICULTY of ANALYSIS

  (6) when he finished, a screen opens and says "If you still have problems with your product, here are a few options for additional support.   Physically, I removed the printer cable to the USB port and choose "UNINSTALL AND REINSTALL with the latest version of the software".  I wasn't expecting to work, but he did.

  (7) I rebooted.  When my pc came, I began to other programs or applications.  I have disabled the firewall software and anti-virus temporarily.

  (8) I have re-inserted cable printer to a USB port

  (9) I open the HP Envy 7640 installation disc and click with the right button on the file: E7640x64.msi.  I clicked on install

  (10) software installed without error.  I then went to my office, clicks on the icon HP ENVY 7640 series... and VOILA!  My Printer Wizard now works!

  (11) I turned on my firewall and anti-virus back and I'm IN business

  Hope these instructions can help someone else.

• HP Envy 5530: HP ENVY 5530 "cannot find the printer"... impossible to see where I am going wrong!

  Hello

  We just put a HP Envy 5530, set up was fine, I tried installing but get the message "cannot find printer" over and over again.

  I tried to download printing HP and Scan doctor but also, it does not find the printer.

  I ran two reports of diagnoses on the printer, everything looks ok, I have an IP address with an IP address that suggest that it has connected wirelessely, the network report said no problems were discovered.

  I tried disabling my firewall, all made once again, still nothing.

  I put the IP address in the address bar, but it does not open!

  I don't seem to have a printer/USB cable witht the printer so I can't tey wireless - I one of them, it was a new purchase?

  I don't really have an idea what to do next, it seems I have a printer connected to the network, your laptop to talk to the network but nothing to talk with each other. I also tried to find the printer with my IPad, but he also could not find a printer.

  Any ideas, im really frustrated

  Thanks in advance

  Hello

  They are on the same Beach, they should be. Now please reset it and try again

  1 reset the printer

  b press settings (wrench),

  (b) press tools then use the arrorw down to access page 2/3,

  (c) touch Restore Factory Defaults - wait a few minutes

  2 reinstall the printer

  (a) you can use the CD, but it will download the file and may take ages to download. Please download the software and the following drivers

  http://ftp.HP.com/pub/softlib/software12/COL47810/MP-115828-6/EN5530_198.exe

  (b) turn on the printer,

  (c) right click on the downloaded file and select run as administrator.

  d select Wireless and then follow the instructions on the screen.

  Kind regards.

• HP Envy 5660: HP Envy 5660 will not be printed on cardstock

  I just spent over an hour on the phone with tech support trying to 1 million different options to allow me to print. A week ago, I bought this printer to print on cards for the baptism of my son (in 2 days) and he refuses to print on thick paper. Technical support tried different drivers, printing through the viewer of PDF, Word printing, printing of a multitude of different parameters, since the photo tray, since the main tray, wireless, USB, etc. Nothing WORKS! I need to get there as soon as POSSIBLE. I find it very difficult to believe that this 'thing' print on photo paper but impossible to print on card stock of all things. Help, please! If HP someone sees my case number is 3028801369. Thank you.

  Hi @mirurzun,

  Thanks for joining the Forums of HP Support for a solution to your printing problem.

  I understand that you use a HP ENVY 5660 e-all-in-one printer with a Mac OS X 10.11 El Capitan computer and you cannot print on thick paper with success. I would like to help with that.

  I went and checked the case created by the agent who you work with. He noted that the end of the document appeared at the top of the card stock, but when you use plain paper it printed fine.

  I called HP ENVY 5660 e-all-in-one printer (F8B04A) specifications and found that cardboard did not appear as a type supported media which is probably why you are not able to make it work.

  If this helps you find a solution please click the 'accept as Solution' and the 'thumbs up' buttons down below in this message.

  Thank you!

• HP Envy 110 - cannot scan from printer (using Mac Maverick)

  I have a MAC with OSX 10.9.4 operating system and a printer HP Envy 110 with the newest driver printer HP Maverick.  I can scan Mac.  However, I can not run a scan directly from the printer control panel.  The sign says "make sure that the HP printing software is installed.  For MAC and USB connections, "Enable Scan to Computer" is automatically activated".  Everyone else has had a similar problem?

  Hi Melnee,

  Thank you for your answer! Please, try the following solutions:

  • Reset the printing system. OS X Mavericks: reset the printing system.
  • Verify and repair disk permissions. 12.x disk utility: repair disk permissions.
  • Look at this post, Re: iMac OS X 10.9.3 scan driver for HP OfficeJet Pro 8500 a A910a to iMac doesn't seem to be, by my colleague @Sunshyn2005.

  Hope this information is useful and have a great day!

• HP Envy 5530 (5534) is not printing special products

  I'm unable to print documents from an Office such as Microsoft Word or LibreOffice Writer product.
  If I print from Adobe Acrobat reader, a browser, or notepad it works fine.

  Scenario:
  -J' use the print dialog box in Word or Writer and select the correct printer (and have a default limit) and click on 'print '.
  -Action is correctly managed (seems treatment and the printer icon appears in the windows taskbar)
  - Is the thing: no print job is added to the queue of the printer (East remains empty) jobs are in the queue, but are removed directly without being print

  When I print from 'all' another application is the same, but a real print job is then added to the queue of the printer.

  Info:
  -J' have the latest printer drivers installed
  -J' tried to disable the firewall and virus scanner
  -printer is HP Envy 5534 (material is the same as 5530)

  What I tried:

  -When I use 'HP print and scan doctor' and follow the steps are all "fine" and the "test print" button leads to a successful impression.

  -reinstalled / printer driver

  -J' tried both local WiFi and via USB printing

  -When I try to manually add a printer by selecting the port 'HP discovery Port Monitor' I get the error 0x0000007b. Is this related?

  Does anyone have a solution?

  I contacted HP Support and they put a lot of effort to resolve this problem. Together, we spend about three of us and we finally found the cause: my computer has been infected by a virus (led).

  Viruses seem to Nestle between you and your printer even collect printed...

  This virus was not found by Microsoft Security Essentials.

  Because I was running as a user administrator, the faster (and better) way to get rid of the virus was to reinstall my PC.

  You can also try a decent anti-virus.

  After that everything works well again.

  I hope this helps others with the same printing problem.

• HP ENVY 4500: Wired DESIRE 4500 printing

  Should what kind of cable I connect my laptop to the HP ENVY 4500 printer.  I'm tempoarily without Wifi.

  Hey @mimijack,

  Welcome to the Forum from HP Support.

  I see that you're looking to print without WiFi using your HP ENVY 4500 e-all-in-one printer. I would like to help.

  What you need is a usb cable:

  

  In particular, you need as pictured above, with the square with split ends. These usually come with the purchase of an external hard drive. They are available in all office supplies stores. When you make the physical connection, click here to install the printer.

  Let me know if you have any questions apart from that - I'm always happy to help you. If I helped you to solve the problem, feel free to give me a virtual h.o.t. by clicking the "Thumbs Up" icon below and by clicking to accept this solution.

  Thanks for posting in the Forum from HP Support. Have a great day!

• ENVY 5540 All - In - One Printer: how to change the password want TO 5540 WIFI Direct from HP default to a different password?

  I try the functions on my new 5540 ENVY. Everything is set up and working correctly so far. I just printed a document from my iPad using the WIFI Direct function on the printer successfully. However, the default password on the printer for the WIFI Direct is simply "12345678". Surely, it should be replaced by a more secure password. My friend something printed its iPad - so obviously, this password is not exclusive to me, anyone can print stuff on my printer just for fun and I have a lot of students around me, the problem could become expensive for me and very boring. WIFI Direct signal covers a distance. I contacted HP telephone support, but the process is time consuming and I had to hang up because I had to work. Maybe someone here could give me instructions, and I can change the password when I have free time. I use wifi for internet (cable ethernet only) and the printer connected via USB to the computer. Also, when I turn on my computer (BUT NOT THE ROUTER) on the wireless function, the printer is and what I need to do is enter "12345678" and start printing. There is no guarantee either. Can someone tell me how to change the password for WIFI Direct 5540 envy? Thank you.

  I'm sure that you can change the EWS web page for your printer.

• HP Envy 4500: Cannot print Photos and large documents on my HP Envy 4500 all-in-one printer

  Hello

  I bought my Hp Envy 4500 all in November last one. It worked like a charm for the first 2 months. I tried to print photo 4 x 6 a day. 2 first impressions were good, and the third image has begun to fade from the half. Documents not threatened by more than a few pages. I tried to uninstall/re-install, printing via USB, set static IP address on the print and followed by other solutions on this forum. I was lazy to lift a question myself on this forum. Now, I'm totally frustrated and disappointed by this product, I wanted to just try my luck.

  Help, please!

  Thank you

  Fox

  Hey @Kvelrajan,

  Welcome to the Forum from HP Support.

  I understand your ENVY 4500 HP e-all-in-one printer is not printing documents to the end and there is a print quality problem when you print photos.  I would like to help.

  I have some suggestions that can solve these problems.

  First, I recommend that you only perform a "hard reset":

  1. press the Power button to turn off the printer.
  2. unplug the power cord at the back of the printer.
  3. wait 60 seconds.
  4 reconnect the power cord to the back of the printer.
  5. press the power button to turn on the printer.

  Click on the title of the following article:

  HP printers - HP wireless built before 2010 printer print a partial Page or fails to print all Pages in Windows 8

  Try Solution two.

  If this clarify two questions, great!  If this solves the problem of document but still the problem of print quality with photos, click on the title of the following article:

  Printer prints a blank Page or does not print black ink color for the HP ENVY 4500 and Deskjet Ink Advantage 3540 e-all-in-One Printer Series

  Work your way through the Solution one and go until you are satisfied with the print quality.  Test photo print - does clarify the issue of the photo?

  Please let me know the result of your troubleshooting by responding to this post.  Feel free to click on the "Thumbs Up" icon below, if I solved your problems.

  Have a great day!