16GB SSD in Lenovo Y500 has stopped working

Similar Questions

• Bluetooth Lenovo S10e has stopped working - device not found / not recognized USB device.

  Hello

  For no reason that I know, installing bluetooth on my small S10e has stopped working.

  I noticed a few times when stop I had a "BTstackserver" does not message.

  I use the laptop to download regularly from a device compatible bluetooth.

  Today, when I go to connect, it says "bluetooth device not found".

  "Verify that your device bluetooth is properly connected and turned on".

  Hardware manual displays the config of LED and is correct, that if I press the "Fn" keys and "F5", I get the menu to turn on and off both the wireless and Bluetooth. I can turn on and off Bluetooth and wireless both with this menu option, BUT when I activate the bluetooth, I get the message 'one of the USB devices attached to the system is faulty or is not recognized.

  I deleted the Bluetooth installed and re-installed software by using the two bluetooth install files published on the list of drivers on lenovo S10e. Neither one works. I know that you need to install dir C:\DRIVERS once Setup has finished unpacking.

  I tried several other obvious things but without success. I also enabled "Bluetooth coopération" in the wireless LAN settings.

  All I can do now is get to the Bluetooth device under the keyboard cover and take a look at that? Anyone who has any suggestions until I get out the screwdriver? (The unit is out of warranty).

  

  I received my replacement bluetooth module and installing it, bluetooth is working again.

  I keep getting "BTW stack server" stopped responding when stopped down, but this does not seem to cause any problems.

  Too bad that original bluetooth module did not survive barely a month after the end of warranty date...

  I'm used to a greater reliability of Lenovo.

• Y500 Lenovo webcam has stopped working.

  Hello, recently I bought a Y500.
  After installing Windows 7 X 64 and start a conversation on Skype fot the first time
  Webcam worked without problem. After two days, I tried to make a video call, but the unit does not start
  Circle turns the camera LED lights but the screen is black.
  I tried the site. Testmycam.com has picture but fuzzy.

  Reinstall the drivers, I installed an older version of Skype 4.2 version but problem not solved... Help me please.

  Hello.

  I had the same problem.
  Just go to the Lenovo website and download and install the driver for Windows 8. Then everything works fine again.

  Greetings from Christian to the Denmark

• Cannot run Lenovo System Update error tvsu.exe has stopped working

  Original title: tvsu.exe has stopped working

  When I run it on my WIn7 64 bit notebook Lenovo System Update v4, I get the following:

  TVSU Application has stopped working

  A problem caused the blocking of the program works correctly. Windows will close the program and notify you if a solution is available.

  I called Lenovo and they say it's a Windows problem. This message looks like a standard message for a particular type of problem. Ideas for a solution?
  Thank you

  Thanks, Eddie!

  I've been reluctant to use these registry cleaners too but had no choice. They well with basic cleaning after uninstall. It is heartbreaking how reckless SSII is during the cleaning of the registry during the uninstallation of their software. And some of the best cleansers will warn you if a fix is dangerous or not you can not run it. But what sometimes happens is that vacuuming can cause two problems for everyone that it fixes if you aren't careful.

  I'll try to post on the site you posted. I'll post here if it helps.

• Windows live photos has stopped working on my LENOVO windows 7 PC.

  When I try to open "Windows live photo gallery", the site becomes blurred, and I get a pop up saying "Windows live photo gallery has stopped working".

  I clicked on "find an online solution & close program", and I get nothing. Under 'View problem details,' he said 'The problem event name' - APPCRASH: name of the Application - WLXphotogallery.EXE and a ton of stuff after that.
  I downloaded all the latest security news, and that did not help.
  Someone has any idea how to solve this problem?

  I came across a somewhat acceptable 3-step solution to the problem of the photo library to break with the message, "Photo Gallery stopped working" shortly after the start. This workaround and the problem it addresses only apply to computers with AMD or ATI graphics cards.

  1. Use Windows Explorer to navigate to the following folder (Win + E).
     • %ProgramFiles%\Common Technologies\Multimedia ATI
  2. Rename the following files in a temporary thing. For example, add "-off" at the end of each name. Note: these files may appear without ".dll" at the end, depending on your system settings.
     • AMF-wic-jpeg - decoder32.dll
     • AMF-wic-jpeg - decoder64.dll
  3. Restart Windows.

  AMD is rumored to have a fix on the way to a bug in the driver files. But, this work around 3 steps will be likely welcomed by fans of photos, until that day comes.

  Note: After you apply this workaround solution your computer may encounter minor performance problems. And, if you update or reinstall video drivers AMD/ATI, the roar of the Gallery of photos can reproduce until you reapply this workaround solution.

  I want to give credit to the one who first developed this work around. But I got used with no citation provided.

• P50 win 10 Pro - footprints digital has stopped working

  Hi all

  I just got my P50 (20EQS00600, M1000M, i7-6700HQ, 16 GB of RAM, 512 GB SSD) about a week ago and I quite like it. However, there is one thing that drives me crazy: after that I upgraded to Win 7 Pro 64 bit for win 10 Pro, the fingerprint feature has stopped working. This issue seems to be related to those reported in these two threads for the P70, but at the same time appears sufficiently different to warrant a new post:

  https://forums.Lenovo.com/T5/ThinkPad-P-and-W-series-mobile/P70-fingerprint-software-issue/m-p/22517...

  https://forums.Lenovo.com/T5/ThinkPad-P-and-W-series-mobile/fingerprint-and-sound-problems-P70/TD-p/...

  So, here is what I did:

  (1) I correctly installed Win 10 w/o retaining data/settings from the previous installation of Windows 7; I even reformatted the SSD drive.

  (2) for the initial installation, was asked by Windows Hello register prints I've done.

  (3) fingerprint worked during the first connection, but then disappeared as if by magic. Hello Windows is no longer appears as a connection option in the control panel of Win.

  (4) I found in Device Manager the Synaptics WBDI reported the following problem: "this device cannot start. (Code 10) ".

  (5) repeated uninstall and reinstall drivers are without success. I tried both have Win a driver and manual to install the drivers I downloaded from Lenovo page.

  (6) when I uninstalled the drivers and then wiped the fingerprints stored in the BIOS, I was again able to register fingerprints with Windows Hello. However, this time the fingerprints were not yet registered in Windows, and I had to cancel the procedure. Immediately after, the Synaptics driver stopped working, cf. 4).

  I am at a loss what to do. Strange thing is that I ran Win 7 for about a week, and the fingerprint reader worked fine all the time. (Due to the scaling of the questions on my 4 k screen, I bit the bullet and went to win 10, in case you're wondering.)

  So everyone out there has the same problem, does anyone have a solution?

  Thank you in advance and the best,

  A

  
  

• iTunes has stopped working / Win10 64

  Hello

  I have a problem running iTunes on 64-bit Windows 10. (Lenovo Thinkpad Yoga 12)

  As soon as I click on the iTunes Store tab, the program crashes and I get the message "iTunes has stopped working, Windows is checking for a solution to the problem..." and after a few seconds he said "a problem caused blocking the program works correctly. Windows will close the program and notify you if a solution is available. »

  I have already tried:

  Complete uninstallation of all programs Apple, including the deletion of all files, and then reinstall it.

  If I do this, the installation fails. He tells me that the bonjour service cannot be started.

  That's why I opened archive installation with 7-zip and has just installed iTunes and support the application. That worked well, but I still get crashes.

  I don't know what else I could try and you'd be grateful for any help!

  Thank you and best what is the Switzerland

  Jonas

  The 12.3.3.17 version seems to cause problems for some people. It may be best to roll back to the last version of iTunes that has worked for you. then wait for the following. See the programs installation of iTunes to download links. If you're back from 12.3.3.17 to 12.3.2.35, then you must also restore the database of the library in the manner described in the empty/corrupted after upgrade/crash iTunes library.

  TT2

• iMessage, FaceTime has stopped working

  iPhone 5 16GB, iOS 9.2.1 (13D 15)

  MacBook Pro 13 end 2011, OS X El Capitan (10.11.3)

  Hello guys,.

  just need some advice. I am (was) using iMessage and FaceTime on my iPhone and MacBook. Last week I went on a business trip to London and got notification that I can't use the iMessage and FaceTime (which was OK, because I got the same message on my business trip to the Ukraine and everything worked fine after) but when I got back to the Czech Republic, iMessage and FaceTime has stopped working. I tried to sign and sign back on MacBook and nothing. I got notifications in iMessage and FaceTime on my MacBook which now using my phone with number correct everything and it still does not work. Does anyone know what what could be?

  Thank you.

  What happens when you try to send a message or launch a FaceTime?

• Button ThinkPad 8 Windows has stopped working

  All of a sudden the Windows button has stopped working (no haptic feedback). The Tablet works otherwise, I can always power on it by the power button / stop. Unfortunately, the button power seems to be fragile and probably collapses when it is used on a daily basis.

  Someone has an idea if possible otherwise remedy that is rented for a month in the repair? A loose connector, or something like that? I don't think that it may be a software issue.

  Thank you.

  First Windows button has stopped working, but now, after several weeks, the touchscreen so. I got replacement touch screen cable AP HM 00, 124 of the Lenovo service replacing the cable has solved.

  I guess that's a design flaw , because the cable is longer than it supposed to be (see photo) so it becomes distorted and there caused by a variable pressure on the bottom when cover stand by the fingers on the lower part of 3 mm approximately. Fixation by band does not help, because it always "bubbles" somewhere I hope that this will happen again sooner or later these other two cables (audio connector and display) is not the issue.

  

• RTFTrack has stopped working message followed computer crash

  I have a Lenovo Edge 15 (got 11/03/15). Recently, when using SKYPE, making a video call, a box has developed indicating that RTFTrack has stopped working. The screen becomes white, then the computer crashes. So my call is disconnected, my computer restart and I have to log in again, open SKYPE, etc. What happened 5 times in the last three weeks. What can I do to fix this?

  Apparently RTFTrack is from Realtek Semiconductor and RTFTrack appears in my Start Menu and begin to start my computer.

  I appreciate your help with this. Thank you.

  I updated my driver of the camera from the 20/03/15 update driver on Lenovo's Support page for my 15 Edge and the problem has not yet appeared. I'm keeping my fingers crossed.

• Lenovo easy camera stopped working (Lenovo Z470)

  Hello, we recently bought a lenovo z470 laptop. the webcam works fine for 3 weeks or more. We were able to use the webcam with Skype and easy capture. I don't really know when the machine has stopped working, but it seems that all software that uses a camera can't detect the camera driver. I am absolutely sure that the FN + ESC hotkey works very well since I can turn off and turn on the camera. I've read many threads with the same problem. I uninstalled and reinstalled the drivers and easy capture but this does not solve my problem. I hope someone can help me. Thank you

  I have already corrected the problem. I have reformat the computer laptop and instead, I installed youcam. now here is the bad part, I think the issue started when I updated my gt 520 m NVIDIA geforce because I need to update to be able to play heroes of Newerth.

• Windows host process (Rundll32) has stopped working

  Is a general Vista problem and also a general problem of Thinkpad, but it has what I feel to be a frequency among the W500s so I thought to post it here.

  In recent weeks, I got this error (Windows host process (Rundll32) has stopped working) several times. A lot of googleing will tell you that it can be caused by a number of things, for example other video programs, Nero burning software, video codecs and burning software and the ATI catalyst control center.

  For me, uninstalling the ATI catalyst control center and the rest of the correction of the error of video card drivers. Resettlement has reduced. Uninstall them and then only by reinstalling the driver first, then check catalytic Center later after another reboot all reinstalled successfully and also got rid of the error.

  However, two days ago I updated my lenovo Power Manager and after the next restart, I started getting this error again. I tried the trick with video drivers, but this time I was not so lucky. Uninstall them completely is not even get rid of the error. I think only it is the new power manager I uninstalled everything and somehow got rid of the error.

  I'm about to reinstall the power manager and I hope he's not bring error.

  Another thing, I found that can cause this error:

  I'd just do a fresh install of vista and lenovo apps + Manager supply and everything worked. Since I never use the optical drive, I went to the Device Manager and disabled, which gave me the error Rundll32.exe about 60 seconds later, and this caused again Manager power to stop working, even after that it recharges.

  I finally understand that disabling my optical drive Springs somehow this error on me which then also stops Power Manager. The optical drive from the reactivation got rid of the error immediately.

• "Repair of system application has stopped working".

  Hi, I'm hoping to get help with an error message that suddenly started appearing on a regular basis. In recent days, the following message if poster every time that I turn on my computer, before that I even click on anything whatsoever.

  Repair of system application has stopped working

  
  

  Signature of the problem:

  Problem event name: APPCRASH

  Application name: UpdateMonitor.exe

  Application version: 4.20.729.0

  Application timestamp: 488e9107

  Fault Module name: StackHash_e52f

  Fault Module Version: 0.0.0.0

  Fault Module Timestamp: 00000000

  Exception code: c0000005

  Exception offset: 00000000

  The system version: 6.0.6002.2.2.0.768.3

  Locale ID: 1033

  Additional information 1: e52f

  More information 2: e98dfca8bcf81bc1740adb135579ad53

  Additional information 3: 860f

  Additional information 4: 6eabdd9e0dc94904be3b39a1c0583635

  No matter what I click 'close' or 'check online for a solution (recommended)', the dialog box WILL NOT GO AWAY. I was going to do a system restore, but I have only two restore points and both are from today, so that obviously is not going to help.

  It drives me crazy and I don't know that this is not a good sign for my computer either. Help, please!

  Thanks in advance!

  -Renata

  
  

  Hello

  You use a Lenovo computer?

  updatemonitor.exe is an application of Lenovo.

  I suggest that get you in touch with the manufacturer for a better support.

  Aziz Nadeem - Microsoft Support

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• Sony Self Extracting package has stopped working?

  So, I got an Acer Aspire 5253, and I try to install Sony Vegas Pro 9.0 trial, since it is the cleaner version, produced. I tried Pro 10 and 11, and they run painfully slow. Anyway, every time I try to install it (9 Pro), I get the same error

  "Sony self-extracting package has stopped working".
  I tried to download the trial of countless sites, including the Archives of download of Sony, but nothing works! I have the feeling that it is a driver problem but I tried to modernize, start in safe mode, etc.; But still the same error.
  That's what happens with:
  Signature of the problem:

  Problem event name: APPCRASH

  Application name: vegaspro90_32bit.exe

  Application version: 1.0.0.1

  Application timestamp: 49d55ff5

  Fault Module name: vegaspro90_32bit.exe

  Fault Module Version: 1.0.0.1

  Timestamp of Module error: 49d55ff5

  Exception code: c0000094

  Exception Offset: 0008018d

  The system version: 6.1.7600.2.0.0.256.1

  Locale ID: 1033

  Additional information 1: 0a9e

  More information 2: 0a9e372d3b4ad19135b953a78882e789

  Additional information 3: 0a9e

  Additional information 4: 0a9e372d3b4ad19135b953a78882e789
  The 64-bit version does the same thing, so I don't think that is the question. Another thing is weird, I tried downloading versions Pro 7 and 8, and they say the same thing...
  Help, please! I tried the Sony site, responses from Yahoo and other sites, but I don't think it's a problem with the software, but windows.

  The machine material is perhaps too fast for the software runs correctly?  Do you use SSDS as primary drive?  If so, can you install the program on a slower hard drive?

  This is the type of error, I think, this is only a guide to prove the error and not a solution as such.

  Division by zero
  http://www.Tek-Tips.com/viewthread.cfm?QID=1254517

• Even with safe mode Windows 7 error "Windows Explorer has stopped working". Screen is blank with only the specified cursor.

  Using Win 7 Home 64 bit:
  After the connection, I get "Windows Explorer has stopped working" its InPageError says in details
  Auto check solution online does not come to the top with a solution
  the screen is black nothing happens.

  I opened in safe mode, same problem.

  the only thing I can do is ctrl/alt/del and open Task Manager. When I tried to open the new task... Task Manager stopped working

  Request of guid, how to solve this problem. The problem started last night.

  The laptop is Lenovo G550
  Operating system: Win 7 64-bit service pack 1 - home edition

  I can email a screenshot is necessary for the InPageError
  Error state code: c0000185
  Type of media loopholes: 00000003
  OS Version:6.1.7601.2.1.0.768.3
  Locale ID: 1033
  More information 1:c785
  More information 2:c785ae48d9bd3e84e80fe64557c132ac
  Information additional 03:58 d 5
  More information 4:58d5c6fbf156506f476a5bd1fc86cfbf

  Hello

  This problem may be due to one of the following problems:

  • You are using an outdated or corrupted video driver
  • System files on your PC can be damaged or do not correspond with other files
  • You may have an infection of viruses or malware on your PC
  • Some applications or services that are running on your computer may be responsible for Windows Explorer to stop working

  Try the following steps:

  Method 1:

  Try the steps of error: Windows Explorer has stopped working

  Note: the data files that are infected must be cleaned only by removing the file completely, which means there is a risk of data loss.

  Important: the data available on bad sectors may be lost when chkdsk attempts to repair your hard drive.

  Note:

  Ignore them perform a upgrade in Place the link above.

  Also ignore the safe mode and clean boot.

  Method 2:

  We will try to start the computer in mode low resolution and check the status of the issue.

  Low resolution starts Windows using your current video driver, and using the parameters of frequency low resolution and refresh. You can use this mode to reset your display settings.

  Refer to the section:

  Turn on the video resolution (640 × 480)

  You can also check: why is my screen black when I start Windows 7?

  Registry warning: the following steps include changing the system registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article:

  Backup and restore

  http://Windows.Microsoft.com/en-us/Windows7/products/features/backup-and-restore

  It will be useful.