2 minute delay in the RESTART system after Windows 8 upgrade to 8.1

Similar Questions

• I continued to have this message flashing on the screen "ERROR of LOADING of THE OPERATING SYSTEM" after the restart when loading the software Window XP.

  Original title: someone help please?

  Working on my old computer, a pentium 4, card mother GA81PE1000, I continued to have this message flashing on the screen "ERROR of LOADING of THE OPERATING SYSTEM" after the restart when loading the software Window XP. After so many years, working on the construction of computer & repair, it's new to me.

  So I checked the Microsoft Website for answers from people with the same problem in the past and apply their suggestions, nothing works... hard drive replaced, the changed value in the bios, did everything possible, still nothing works, phenomenal for me, please help me find an answer, thank you?

  Hello

  1. have you made changes on the computer before this problem?
  2 - what you want to say that you receive this error message during the installation of Windows XP?

  Check to see if the following is useful.

  Method 1: Disconnect all devices non-essential connected to the computer and restart. Check to see if it boots normally.

  Method 2: You may need to check the settings of the BIOS (Basic Input\Output System). Check if the hard drive is detected. If this is not the case, check the physical connections. Refer to the manual to check the same.

  Warning of the BIOS:

  BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  The following article might be useful: "Error loading operating system" Error Message When you restart your computer during installation

• Install the operating system after replacing the corrupted hard drive Asus q500a

  The hard drive on my Asus Q500a is bad (he had checked the repairman). They told me that I could replace it (it will just keep failing until at last it dies just) but I have to re - install the operating system. The laptop comes with Windows 7 and I upgraded to 8 when it came out (I think). I don't have a recovery disk.

  How can I replace the corrupted hard drive and re-install the operating system?

  If I need to buy Windows 8, where can I find?

  Would it not easier that I left the repair shop handle it?

  Thank you in advance.

  Hi Kristi,

  Thank you for visiting Microsoft Community and we provide a detailed description of the issue.

  According to the description, I understand that the problem with you want to reinstall the operating system after replacing the hard drive corrupted on the system.

  Certainly, I understand your concern and will try my best to help you.

  I suggest you check the suggestions contained in the Microsoft link below and check if this is useful.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-windows_install/replacing-hard-drive-and-re-installing-Windows-8/e8dbfc81-5294-4c94-9276-0f36e0a66e59

  In addition, you can see the suggestions in the link given below.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-windows_install/reinstall-Windows-8-after-the-operating-sytem-has/30d47e63-296b-4466-ae9d-4628084541dc

  I hope this information is useful.

  Please let us know if you need more help, we will be happy to help you.

  Thank you.

  Jayant

• I have a laptop asus F5R model. I use the operating system to windows xp service pack 2, I can't install the audio driver on my knees, please help me

  I have a laptop asus F5R model. I use the operating system to windows xp service pack 2, I can't install the audio driver on my knees, please help me

  Download and install the last set of drivers (starting with the chipset / driver motherboard) to the ASUS support site: http://support.asus.com/download/options.aspx?SLanguage=en&type=1

  J W Stuart: http://www.pagestart.com

• I'll be able to restore the backup taken before improving the operating system of Windows Vista Edition home premium for Windows-8

  I'll be able to restore the backup taken before improving the operating system of Windows Vista Edition home premium for Windows-8

  Hi GOURGOPALGHOSH,

  Welcome to the Microsoft community. Yes, you will be able to restore the backup before the upgrade to Windows 8. Follow these steps:

  (a) press the Windows key + W.

  (b) type of recovering files of Windows 7 , and then press enter.

  (c) restore files.

  I hope this helps. Let us know if you need more assistance.

• This application is not compatible with the operating system installed. Please upgrade to Windows 98SE, Windows 2000 or more.

  Hi all

  I recently installed a mod for S.T.A.L.K.E.R SoC V1.004. The game won't start not even, instead, it gives me the following message:

  This application is not compatible with the operating system installed.
  Please upgrade to Windows 98SE, Windows 2000 or more.

  I'm under Win 8 64 bit. I have uninstalled and rebooted twice (both game and mod) does not.

  I have to downgrade to XP to be able to play this awesome mod, he ran on this platform with the same configuration before, why he now rejects it know not only the people at Ms.

  Please help if possible

  Thank you very much

  Pierre Viljoen

  Probably, all in all probably is a 16-bit program, and as such does not work on Windows 8.0/8.1 64 bit. In addition, the game seems to have 20 years or more. You can try running in compatibility mode, but I think that the game is dead. Hope this helps and if you need help please post and we will be happy to help you.

  The above opinion is mine and casually and does not necessarily reflect that of Microsoft, they are employees. or any other Member of this forum.

  "When we try to take anything by itself, we find it hitched to everything else in the universe"-John Muir

• PSE improve and change the operating system from Windows to Mac

  Hi all

  In 2005 I bought initially PSE 3 and PSP 3 for Windows.

  In 2009, I upgraded to Version 8 for Windows PSE

  Now, I've changed the operating system for MAC and upgraded to PSE & PSP 14.

  When you go to the store, I can select and upgrade package - but only for Windows (I guess because of my previous purchases for Windows).

  How can I change for MAC now?

  Anyone any idea or had the same challenge?

  Thank you very much in advance for any advice or insight.

  
  Michael BR

  Hi Michael BR,

  Please use the following link to upgrade to Photoshop elements 14. See, photo editor software & tools | Adobe Photoshop Elements 14

  There is a drop down next to the platform: Windows click on in order to change for Mac, see the screen capture below.

  

  Photoshop is no longer available as a stand-alone product, and it is only available as a cloud creative/subscription for more information see, pricing and membership creative cloud plans | Adobe Creative Cloud

  Let us know if that helps.

• Why can't I enter my upgrade key after Windows Anytime Upgrade on Vista?

  I bought the software update Window 7 Ultimate. I followed the instructions on the box:

  Click the Start button

  In the search box, type Windows Anytime Upgrade

  Click Windows Anytime Upgrade and clide enter an upgrade key.

  Yet, there is no link that says enter an upgrade key. There is only a link to the site Web microsoft talks Windows 7.

  I downloaded the Windows Upgrade Advisor. I did everyting that he told me to do. He checked that the computer was eligible for an upgrade (Toshiba Satellite running Vista).  I tried again with the Windows Anytime Upgrade again. There is still no link to enter the upgrade key.

  What should I do to get to the place to enter the upgrad key?

  Please note that there are no Windows Anytime Upgrade (WAU) for Windows Vista to Windows 7. There is only Windows Upgrade (WU) in which you need to buy a Windows 7 disc and upgrade of the key. You can refer to the link below for more information about upgrading Windows Vista to Windows 7.

  http://Windows.Microsoft.com/en-us/Windows7/help/upgrading-from-Windows-Vista-to-Windows-7

• I want to know if I need to install Vista on it for the purchase of a Windows 7 upgrade edition?

  Editions of Windows upgrade

  Hey guys, I have a Windows Vista free disk and I'm building a new pc. I plan Windows 7 Pro, but I want to know if I need to install Vista on it for the purchase of a Windows 7 upgrade edition, or can I use the product key that came with Vista, when you install the updated version?

  In order to use the versions of Windows 7 upgrade, you must have a previous qualification license installed (Vista or XP), Windows 7 upgrade must be a compliance check. There is no need to activate it if.

• 11 - k000na: problem of restart of the operating system after disk erasing

  Hi there are members of the HP support forum!

  I bought my product, the HP Pavillion 11-k000na, in October of last year and around in time to March this year, I found the speed of the computer to be really bad, so I decided that I do a disk cleanup and restore the computer to factory settings I've done. Restart the computer, I discovered that something has gone wrong and after many failed attempts I could not restart the operating system.

  Time and time again, the laptop gives me the same error - message

  Error code 0 xC0000001

  When I bought the computer it came installed with windows 8 and I've quickly updated to windows 10, would be the problem that when I restored it to factory settings, it does not know how to restart now?

  Any help would be really useful thanks!

  Oliver

  Hello

  On the upgrade of Windows 8 to 10, built in recovery partition got corrupted and will stop running more.

  How do you reset phone?

  Only I know is to order for your model of HP USB recovery. Or pure 8.1 Windows update install using Windows Media creation tool. Both methods retrieve product key of activation of the Board BIOS chip, automatically and be activated.

  Concerning

  Visruth

• Impossible to download and reinstall the operating system after erasing HD

  Yesterday morning, my iMac won't start.  It was fine the night before.

  The progress bar reaches about two thirds to three quarters of the way to the end when the bar of progress disappears and I find myself with a gray screen. It does this by starting too.

  I followed the advice of Linc Davis at https://discussions.apple.com/message/21333265 (hash) 21333265 (Note - I can't find the symbol of hash on my keyboard key so if you if know where he is, please replace by in the link - oh (hash) and tell me where it's too please ;-)).

  I started the Revovery volume (now here actually).  Run Disk Utility/First aid finds no problem with MacIntosh HD (my boot drive). I can't find how to repair permissions.  The option no longer seems to be there. Reset NVRAM has nothing else that makes the iMac wonder my preferred language.

  I used download and reinstall OS option.  The first time I tried to re-download El Capitan, it took 15 minutes and 45 minutes to install.  Installation failed leaving me to the grey screen again.  I think that the Setup program itself was trying to restart the iMac when he got stuck in the same place I'm stuck.  I left it there for about six hours before I tried to restart manually.

  Tried to download the operating system again. This time, it was after using the recovery volume, select MacIntosh HD, by using erasing, then the option reinstall in THE.

  I did two times now.  The first time I tried 'Erase and re - install' the download bar has got to a point about a third of the way across, and then he stopped. Time of download bar gradually got more and more long, up to what I canceled it (when the display estimated download time is six and a half).  The internet connection was problematic, or the Mac had stopped download (similar to the earier progress bar).  The second attempt to delete and download, the download bar has not yet started to progress.

  My HARD drive has several volumes.

  1. The most important. My MacIntosh HD with OS 10.11.4 - El Capitan.
  2. The second, MacIntosh HD 2, is about 50 GB, a Mavericks installed on it.
  3. The third is 10.11.4 recovery volume.
  4. The fourth is another volume of recovery for the Mavericks.
  5. There is another called eDrive bulkhead.

  Apart from MacIntosh HD, with none of these volumes I problems in starting up (with the possible exception of the Mavericks resumed, that I have not tried to access all since the update to El Capitan).

  I used first aid utility disk several times, and no problems have been reported. I used the version of El Capitan permanently.

  I can't understand why, after erasing the MacIntosh HD to do it again, I can't get the iMac to download the MacOS and reinstall.

  A couple of clues-

  • After his clear utility drive always reports what is MacIntosh HD. (When I restart, the dialog "Select Start Drive" only shows the volume of the Mavericks and eDrive)
  • Disk utility also shows "Apple Disk Image/OS X Base System."  OF THE said that it is ejection. But this button does not work.  I suspect it's what might stop download me the installer and start again.

  I used e-drive to check the iMac and, in particular, the drive HARD; even performed a surface scan.  No problems have been reported.

  Your 2007 iMac is too old to download OS X, you need to install OS X since the recovery partition directly. If this does not work then Yes, something is wrong with your HD run Apple Hardware Test Mode Extended 2 - 3 times back to back, if errors appear which confirms what I said. You will need the original DVD that came with the computer in order to run it.

• Satellite L500 - system hung on the splash screen after Windows update

  Hello

  I hope that someone can help you. My Satellite L500 is suspended on the blue startup screen after it restarted after a windows update, the mouse arrow moves and it seems to be a hard disk with a twinkle activity in the system lights. Except that nothing? Any ideas?

  Thank you
  Denise

  Hello

  > hung on the blue startup screen after it has restarted after a windows update
  This means that you get a blue screen after Windows update and more, you can start Windows t?

  You can start Windows in safe mode?

• myRIO time restores default of the ignition system after reboot

  Hello guys,.

  I have the following problem.
  I measure the tension on each analogue input. The measurement starts after starting the appliance myRIO, while time system of myRIO device resets the time default system. But the measures are useless without a good timestomp, containing real time (day, month, yearh, hour, minutes, seconds).
  Is there a possibility for the device myRIO start with real time, or that unit myRIO has time while turned off. (perhaps someone knows the external devices which can be connected to the USB myRIO to get real time)

  Greetings from the Germany

  Dimasaur

  The myRIO has not shipped for the real time clock battery, so the time will be reset with each power on.

  You can set the date and time on the myRIO using screws on the target System Configuration, so all you need to do is to find somewhere that timestamp and assign once myRIO Boote.

  Here are a few options:

  -If you have a HOST VI connected, send the timestamp for the myRIO from your PC

  -External battery series/I2C/SPI supported RTC chip/module that you can connect to the myRIO. There is an example here.

  -A GPS module provides a very accurate timestamp as part of its NMEA data - could you one until the myRIO e.g. via Serial hook

  -The information of the network timestamp (for example a time server SNTP or by making an HTTP request - the timestamp is usually returned in the header information by the server or you might find a web service that provides information 'current time')

• When you click "Restart now" after Windows Update, the computer stops, does not restart

  When you click "Restart now" to a windows update... the computer cycle throughout the judgment... and not restart.

  * original title - problems with computer restart (ing) after the updates *.

  Hello

  1st thing to try is a restoration of the system in safe mode

  http://www.windowsvistauserguide.com/system_restore.htm

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode option with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  If that does not read this information

  the link below is how to download and get a vista disk startup repair, which you can start from the

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

  It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

  Change boot order it do dvd drive 1st in the boot order

  http://helpdeskgeek.com/how-to/change-boot-order-XP-Vista/

• I had to reinstall the operating system after that Itried to restore my files for the backup that I had already taken in an external drive, the problem is tha files are empty?

  When I am trying to restore my file that I can't reach them, in some cases I can read the name of the file such as the name of a singer, but when I tried to open the file is empty, he said. This happens with my contact and all my media. I lose my stuff.

  [Moved from comments]

  Hi Hector.

  1. what version of Windows operating system is installed on your computer?

  2. you use software to perform the system backup and restore?

  3 is the issue limited to any particular file?

  First of all, I suggest you click with the right button on the backup files and check the size of the file in the Properties window.

  Try to copy and paste the files to the computer and check if you are able to access the files.

  You can also check if the folders are hidden. If the folders are hidden, so you can view folders and check if you are able to access the data.

  1. press the ALT key on the keyboard in any Windows Explorer window to display the toolbar.
  2. click on tools, then Options of folders, and then on the view tab.
  3. then choose "show files and folders". After clicking OK, they appear with the other files.

  Hope that the information provided is useful.