2911 router licenses

Similar Questions

• Cannot connect Cisco Network Assistant to 2911 router

  I'm trying to connect my Cisco 2911 router to my community at the NAC.  I can see the routers in terms of topology, but when I try to add to the community I get an error message indicating that the router is inaccessible (cannot connect).  I can ping client device of soul. I can view the properties of the device to the card (device type: CISCO2911/K9). Telenet attempt connection, but we have only use SSH for connectivity (the same as all my switches that are connected to the community).  2911 is listed as a taken router supported on the Cisco site.

  Any quesses what I am doing wrong?

  Thanks in advance.

  J

  Hello
  You must enable http for can work.

  http://kirkpbm.WordPress.com/2008/07/13/Cisco-network-assistant-enabling...
  Pls link for other instructions above check.

  Rgds/DP
  Sent by Cisco Support technique iPad App

• Ports 10/100/1000 on the cisco 2911 router does support etherchannel

  Hello

  I need like below

  -Ethernet point to point leased - Line1

  --------Trunk-------- 2911 Router                                                                                          2911 Router-------Trunk-------------

  -Ethernet point to point leased - Line2

  I intend to use existing 3 onboard 10/100/1000 ports router 2911 for a configuration of trunk and etherchannel. Trunk connects to local lan conncts and etherchannel for remote sites. My doubt is can I configure 2911 as trunk ports on board and implement etherchannel? From now on, there will be no routing configuration in 2911.

  Concerning

  Siva K

  Hi Siva,

  > As of now, there is no routing configuration in 2911.

  use a LAN switch for this or an etherswitch module installed in routers C2911

  routed ports can be used only routed or bridiging (IRB) ports, you cannot configure the as trunks of L2, you can use them as a L3 port channel but not as a port-channel trunk L2.

  Hope to help

  Giuseppe

• 2911 w/security - VPN with DHCP Relay to Win2K8, routing fail

  Hello

  I have a 2911 router and tries to terminate a VPN inside.

  I want to do this is before the DHCP request to a Server 2008 inside.

  I actually received this part to work.  But it seems to be, 2911 router is not set the VPN clients on a VLAN internal associated with the range of network, the DHCP server is to give.  Or all least, does not have a flow of information between the IP address of the VPN Client and the router itself.

  (washed config below)

  Example: VPN Client obtains the IP address of 10.101.55.10.  The router has a loop (or subinterface in my last iteration of the config) address of 10.101.55.1.

  And yet, when my VPN client connects, I am not able to ping to an IP that my router has.  I can ping myself (10.101.55.10), but I only ping the router in any way which.

  Does anyone have any ideas?

  -----

  Paste config

  -----

  !
  ! Last configuration change at 04:48:18 UTC Friday 25 March 2011 by x
  !
  version 15.0
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  encryption password service
  !
  host name x
  !
  boot-start-marker
  boot-end-marker
  !
  logging buffered 51200 warnings
  enable secret 5 x
  !
  AAA new-model
  !
  !
  AAA authentication login default local radius group
  AAA authentication login userauthen local
  AAA authorization groupauthor LAN
  !
  !
  !
  !
  !
  AAA - the id of the joint session
  !
  !
  !
  !
  No ipv6 cef
  IP source-route
  IP cef
  !
  !
  !
  !
  property intellectual name x
  !
  Authenticated MultiLink bundle-name Panel
  !
  !
  !
  Crypto pki trustpoint TP-self-signed-3088527431
  enrollment selfsigned
  name of the object cn = IOS - Self - signed - certificate - 3088527431
  revocation checking no
  rsakeypair TP-self-signed-3088527431
  !
  !
  TP-self-signed-3088527431 crypto pki certificate chain
  certificate self-signed 01
  3082024B 308201B 4 A0030201 02020101 300 D 0609 2A 864886 F70D0101 04050030
  2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30
  69666963 33303838 35323734 6174652D 3331301E 31393532 OF 30323236 170 3131
  31375A 17 0D 323030 31303130 30303030 305A 3031 06035504 03132649 312F302D
  4F532D53 5369676E 656C662D 43 65727469 66696361 74652 33 30383835 65642D
  32373433 3130819F 300 D 0609 2A 864886 01050003, 818, 0030, 81890281 F70D0101
  8100BB8B DCF74C9C 5068AF8B 17458225 C2C3702C 416CE391 6EA8991B D3CFFA1A
  62FCA661 566A30C5 2ADE1CBF 558335F9 E9811663 819FA2E9 BEEC77CD 768A 5829
  437E90FA 17F50DDE 94B52B67 96E1E8FC E4E7A12C 07E67582 342774 5 DF956CC8
  FAB6BA34 AB2D79B0 771D8D88 40FDDC34 9F5A0145 4A18B252 037DCDE1 8A114B84
  010001A 3 73307130 1 130101 FF040530 030101FF 301E0603 0F060355 0F190203
  551 1104 17301582 1341434 C 50475231 74657374 2E636F6D 301F0603 2E61636C
  551 2304 18301680 14929613 69D7A350 EA595EC1 C1520246 C00CAB37 A2301D06
  04160414 92961369 D7A350EA 595EC1C1 520246C 03551D0E 0 0CAB37A2 300 D 0609
  2A 864886 04050003 81810077 CBE5CA04 9D75B036 CF639BEC EFD03A3C F70D0101
  FB1390E6 5DC1DBF9 7311123D 9A 018140 2509EADC 9F03747E 3D12F993 BB69D424
  AEA4E0A6 75AF5209 4BD15BE0 92BDA0F1 C74245AF C41DB154 E443F8AD 3605EBE3
  F293D601 10 C 07520 FCB38B3E 6AC9AE74 AE9CB2A2 A80CED34 1FE185CF 24B1A689
  A9E1CF15 F3041A8E CE12C914 C53EEA
  quit smoking
  udi pid CISCO2911/K9 sn x license
  !
  !
  VTP version 2
  user name x
  !
  redundancy
  !
  !
  property intellectual ssh time 60
  property intellectual ssh version 2
  !
  !
  crypto ISAKMP policy 3
  BA 3des
  preshared authentication
  Group 2
  !
  crypto ISAKMP policy 5
  preshared authentication
  Group 2
  ISAKMP crypto key address 0.0.0.0 dmvpnkey 0.0.0.0
  ISAKMP crypto nat keepalive 20
  !
  the group x crypto isakmp client configuration
  x key
  DNS 10.0.0.6 10.0.0.3
  area x
  10.3.0.3 DHCP server
  GIADDR DHCP 10.101.55.1
  netmask 255.255.255.0
  !
  !
  Crypto ipsec transform-set esp-3des esp-sha-hmac VPNSET
  Crypto ipsec transform-set esp-3des esp-sha-hmac dmvpnset
  !
  Crypto ipsec profile dmvpnprof
  Set transform-set dmvpnset
  !
  !
  dynamic-map crypto vpn-dynmap 10
  game of transformation-VPNSET
  !
  !
  customer vpnclientmap of authentication crypto map list vpnusers
  card crypto isakmp authorization list groupauthor vpnclientmap
  client configuration address card crypto vpnclientmap answer
  vpnclientmap 10 card crypto-isakmp ipsec vpn Dynamics-dynmap
  !
  !
  !
  !
  !

  !
  !
  interface GigabitEthernet0/0
  Telus MPLS description
  IP 10.101.2.1 255.255.255.252
  IP virtual-reassembly
  Shutdown
  automatic duplex
  automatic speed
  !
  !
  interface GigabitEthernet0/1
  AllNorth hand VPN description
  DHCP IP address
  NAT outside IP
  IP virtual-reassembly
  automatic duplex
  automatic speed
  vpnclientmap card crypto
  !
  !
  interface GigabitEthernet0/2
  Description main trunk to LAN internal
  no ip address
  automatic duplex
  automatic speed
  !
  !
  interface GigabitEthernet0/2.4
  encapsulation dot1Q 4
  IP 10.101.4.1 255.255.255.0
  IP helper 10.3.0.3
  IP nat inside
  IP virtual-reassembly
  !
  interface GigabitEthernet0/2.10
  encapsulation dot1Q 10
  IP 10.101.10.1 255.255.255.0
  !
  interface GigabitEthernet0/2.50
  encapsulation dot1Q 50
  IP 10.101.50.1 255.255.255.0
  !
  interface GigabitEthernet0/2.55
  encapsulation dot1Q 55
  IP 10.101.55.1 255.255.255.0
  !
  interface GigabitEthernet0/2.99
  encapsulation dot1Q 99
  IP 10.101.99.1 255.255.255.0
  !
  interface FastEthernet0/0/0
  switchport access vlan 4
  !
  !
  interface FastEthernet0/0/1
  !
  !
  interface FastEthernet0/0/2
  switchport access vlan 10
  !
  !
  interface FastEthernet0/0/3
  switchport mode trunk
  !
  !
  interface Vlan1
  no ip address
  !
  !
  !
  Router eigrp 1
  Network 10.250.1.2 0.0.0.0
  !
  router ospf 100
  Log-adjacency-changes
  0.0.0.0 network 10.101.2.2 area 0
  !
  VPN IP local pool 10.151.56.1 10.151.56.20
  IP forward-Protocol ND
  !
  no ip address of the http server
  no ip http secure server
  !
  IP nat inside source nat route map - this interface GigabitEthernet0/1 overload
  IP route 10.3.0.0 255.255.255.0 10.101.4.2
  !
  allowed to access-list 23 x
  access-list 23 allow 10.0.0.0 0.255.255.255
  access-list 100 permit udp any host x eq isakmp
  access-list 100 permit esp any host x
  access-list 100 permit gre any x host
  access-list 100 permit tcp any host x eq telnet
  access-list 104. allow ip 10.101.4.0 0.0.0.255 any
  access-list 104. allow ip 10.101.55.0 0.0.0.255 any
  access-list 130 allow ip 10.0.0.0 0.255.255.255 10.101.55.0 0.0.0.255
  !
  !
  !
  !
  nat permit - this route map 10
  corresponds to the IP 104
  !
  !
  x SNMP-server community
  !
  control plan
  !
  !
  !
  Line con 0
  line to 0
  line vty 0 4
  access-class 23 in
  Synchronous recording
  transport input telnet ssh
  line vty 5 15
  access-class 23 in
  transport input telnet ssh
  !
  Scheduler allocate 20000 1000
  end

  Yes, it looks like you might have as a subnet of more large covered in your routing protocols internal hence set up 'reverse-road '.

  Good to hear it works now. Kindly, please mark this post as responded while others can learn from this post. Thank you.

• Add ISDN BRI service on the 2911 voice router

  Dear all,

  There is a Cisco 2911 and ISDN BRI service in the test lab, and we would like to integrate the Cisco 2911 router ISDN service.

  Should purchse the wan 1 port bri ISDN interface card or interface card 1-port analog modem?

  Please let us know of any experience or advice.

  Thank you very much.

  Best regards

  Ben Lai

  It is very good. Then go on a BRI card

• IPS on the version of cisco 2911 (15.0 (1) M3)

  Hello

  Could someone guide me please? I'm under cisco 2911:

  ********************

  Cisco IOS, C2900 software software (C2900-UNIVERSALK9-M), Version 15.0 M3 (1), REL

  EASY SOFTWARE (fc2)

  IPS license status: not installed

  Current date: October 8, 2011

  Expiry date: not available

  Date of extension: not available

  Loading signatures: not available S0.0

  Signature package: not available S0.0

  Cisco IOS, C2900 software software (C2900-UNIVERSALK9-M), Version 15.0 M3 (1), REL

  EASY SOFTWARE (fc2)

  ******************

  When I run the show ip ips:

  IPS license status: not installed
  Current date: October 8, 2011
  Expiry date: not available
  Date of extension: not available
  Loading signatures: not available S0.0
  Signature package: not available S0.0

  Do I have to buy a license for software only, or should I buy a saparate for IPS module work?  How would the license be about?

  Help

  You can run IOS IPS on the 2911 router, however, you must purchase the license IOS IPS to be able to run the IOS IPS feature. Not sure how the license, it is best if you ask Cisco reseller/partner and they would be able to help others with a price.

• VPN Cisco 2911

  Hello

  I am thinking purchase 2911-SEC/K9 Cisco router.

  IM wondering witch VPN types can I use to participate in the network? I think that I read that IPsec site-to-site is not a problem but im wondering PPTP or something like that. What type of VPN solution customer, I can use. IM thinking on the use of the premium Anyconnect if this is possible with the 2911 router. I also wonder how much the cost for this will be user and connection.

  Best regards Tommy Svensson

  Hi Tommy,.

  With a 2911 and the licensing of security for the IOS, you can use IPsec VPN or SSL VPN (AnyConnect).

  Traditionally IPsec VPNS allow remote clients to connect by using a client software and also helps the Site-to-Site connections other peers (ASAs, IOS devices, third party, etc.).

  SSL VPN now offers over HTTPS, which you don't need to worry about encryption at the network layer (as in IPsec).

  It will be useful.

  Federico.

• Cannot install VPN license

  I bought a 2911 router and a pack of 25 VPN licenses (PID: L-FL-SSLVPN25-K9 =).

  I registered the license and provided the serial number of my router when asked. I received a license .lic file.

  When I try to install the license on the device, I get an error:

  % Error: installation failed. UDI L-FL-SSLVPN25-K9 =: FTX1542AKJ3 on the license is not m

  watch any device

  0/1 licenses have been installed correctly

  0/1 licenses were existing licenses

  1/1 licences have been impossible to install

  However, the following text sets out that the serial number is correct:

  Inventory SFGallery #show

  NAME: ' CISCO2911/K9 chassis', DESCR: "CISCO2911/K9 chassis.

  PID: CISCO2911/K9, VID: V04, SN: FTX1542AKJ3

  NAME: 'C2911 AC Power Supply', DESCR: "C2911 AC power.

  PID: PWR-2911-AC, VID: V03, SN: AZS153303LY

  Any ideas?

  Question a TAC case would be my first step.

  HTH >

• Cisco 2911 and ASA 5512 remove double NAT

  Greetings,

  I have 2 subnets on Cisco 2911 router

  192.168.3.0/24 and 192.168.1.0/24

  3rd network 192.168.4.0/24 is natting internal interface to the modem for internet access. creating 2 NAT (NAT in router) and NAT in Modem

  I just bought Cisco ASA 5512, no chance I could remove the Cisco 2911 router NAT and set the default gateway for Cisco ASA?

  Yes you are right...

  You must ensure that you get the routed LAN traffioc to hit inside the interface ASA in ASA, you can do PAT/NAT to access...

  Concerning

  Knockaert

• IPSec with Cisco 819 G (license)

  Hello

  I'm trying to configure IPSec on a Cisco 819 G. According to this document ( http://www.cisco.com/c/en/us/products/collateral/routers/800-series-rout... ), the SL-810-AIS (IP services) licenses and SL-810-ADVSEC (Adv security) are included by default.

  However, Adv security is not enabled:

  Kit-7132 #show function of licenses
  Name of the function application assessment active subscription RightToUse
  advipservices_npe Yes No Yes No Yes
  advsecurity_npe no no no yes no
  IPS-updated iOS Yes Yes Yes No Yes
  WAAS_Express Yes No Yes No Yes

  Do you know how is it possible to get activated in order to be able to configure IPSec?

  Thank you

  No payload encryption.

  The router (license) can not handle the crypto stuff.

• Protect internet router to ddos attack

  Hello

  I have small 2911 router connected the main internet router GSR this GSR a links of peering with Internet service providers, is route by default on 2911 send to EGS and all the user connect on 2911 2911 to GSR, the attack on 2911 ddos attack got my question how can protect against this kind of attack 2911 I have a few questions if you can help me:

  1. What is the need to access list set up to protect the example of router ICMP, HTTP 2911.for...

  2. What is the configuration of COOP to allow us to be able to access this router when attack and CPU high.

  3. I heard ASR and 7200 has some function to protect these router against ddos attack, is useful for all sorts of attack dedos

  Thanks in advance.

  Hi Steven,

  Take a look at the below mentioned link:

  DDOS protection

  DDOS protection 2

  Kind regards

  Anim Saxena

  Community Manager

  * make the rate of useful messages *.

• L2l VPN between ASA with the IP address public and CISCO2911 behind the ISP router with port forwarding

  Hi all

  My apologies if this is a trivial question, but I spent considerable time trying to search and had no luck.

  I encountered a problem trying to set up a temporary L2L VPN from a Subscriber with CISCO2911 sitting behind the router of the ISP of an ASA. ISP has informed that I can't ignore their device and complete the circuit Internet on the Cisco for a reason, so I'm stuck with it. The Setup is:

  company 10.1.17.1 - y.y.y.y - router Internet - z.z.z.z - ISP - LAN - 10.x.x.2 - XXX1 - ASA - 10.1.17.2 - CISCO2911 - 10.1.15.1 LAN

  where 10.x.x.x is a corporate LAN Beach private network, y.y.y.y is a public ip address assigned to the external interface of the ASA and the z.z.z.z is the public IP address of the ISP router.

  I have forwarded ports 500, 4500 and ESP on the ISP router for 10.1.17.2. The 2911 config attached below, what I can't understand is what peer IP address to configure on the SAA, because if I use z.z.z.z it will be a cause of incompatibility of identity 2911 identifies himself as 10.1.17.2...

  ! ^ ^ ^ ISAKMP (Phase 1) ^ ^ ^!
  crypto ISAKMP policy 5
  BA 3des
  md5 hash
  preshared authentication
  Group 2
  lifetime 28800
  isakmp encryption key * address no.-xauth y.y.y.y

  ! ^ ^ ^ IPSEC (Phase 2) ^ ^ ^!
  crymap extended IP access list
  IP 10.1.15.0 allow 0.0.0.255 10.0.0.0 0.255.255.255
  Crypto ipsec transform-set ESP-3DES-SHA 3rd-esp esp-sha-hmac
  card crypto 1 TUNNEL VPN ipsec-isakmp
  defined peer y.y.y.y
  game of transformation-ESP-3DES-SHA
  match the address crymap

  Gi0/2 interface
  card crypto VPN TUNNEL

  Hello

  debug output, it seems he's going on IPSEC States at the tunnel of final bud QM_IDLE's.

  What I noticed in your configuration of ASA box, it's that you're usig PFS but not on 2911 router.

  So I suggest:

  no card crypto OUTSIDE_map 4 don't set pfs <-- this="" will="" disable="" pfs="" on="" asa="">

  Then try tunnel initiate.

  Kind regards

  Jan

• Client certificate and router WebVPN

  Hello!

  In my test harness I can not to run my webvpn configuration =.

  I have several components: AD MS, MS CS (but without NDE), 2911 router and client computer. Client and router have a certificate of MS CS. In my setup I use certificate or aaa (LDAP) authentication and authentication work aaa good. But the client certificate authentication does not work. And my internal https services do not work too--"no certificate or invalid", but this strange because I imported the CA certificate for that.

  Can you help me it work?

  My version of 2911:

  Cisco IOS software, software C2900 (C2900-UNIVERSALK9-M), Version 15.1 (3) T, RELEASE SOFTWARE (fc1)

  My Config:

  AAA authentication login webvpn group local ldap

  IP local pool webvpn 192.168.200.1 192.168.200.254

  bind authenticates root-dn cn = webvpn, OU = team, dc = domain, dc = com password [email protected]/ * /.

  WebVPN vpn gateway

  IP address port 4443

  SSL root-ca trustpoint

  development

  !

  WebVPN install svc flash0:/webvpn/anyconnect-dart-win-2.5.3055-k9.pkg sequence 1

  !

  employee framework WebVPN

  SSL authentication check all

  !

  connection message 'Portal VPN'

  !

  the policy group peche1

  List of URLS "on the inside".

  functions compatible svc

  filter VPN SPLIT tunnel

  SVC-pool of addresses "webvpn" netmask 255.255.255.0

  SVC by default-domain "domain.com".

  SVC Dungeon-client-installed

  SVC split dns "domain.com".

  SVC split include 192.168.0.0 255.255.0.0

  SVC-Server primary dns 192.168.1.1

  SVC-Server secondary dns 192.168.1.2

  Citrix enabled

  virtual-model 1

  strategy-group-by default peche1

  AAA authentication list webvpn

  vpn gateway

  authentication certificate

  user name - sign up

  root CA trustpoint-AC

  User location flash0 profile: / userprof

  development

  !

  Crypto pki trustpoint root-ca

  Terminal registration

  revocation checking no

  rsakeypair root-ca

  !

  I imported with CA pkcs12 certificate.

  My debug (it happened so I am trying to access my webvpn portal and I choose my certificate of MS CS for access)

  5 Jun 11:22:39: WV: validated_tp: cert_username: matched_ctx:

  5 Jun 11:22:39: WV: could not get opssl appinfo sslvpn

  5 Jun 11:22:39: WV: could not get opssl appinfo sslvpn

  5 Jun 11:22:39: WV: error: no certificate validated for the customer

  Can someone explain to me why it does not work?

  Resolved by the update IOS - version 15.2 (4) M2.

  Concerning

• Problem with SHDSL at 2911

  Hello guys,.

  I'm testing the Cisco 2911 router with 1 pair SHDSL HWIC to connect my ADSL connection to the service provider ip static.

  The router contains adsl_alc_20190.bin firmware. But no idea where to start please help configuration ADSL about SHDSL WIC.

  Concerning

  Sudan

  SHDSL HWIC is not supported ADSL.

  Post "display inventory" to confirm the correct hardware you have installed.

• Network home defender MESS!

  under Vista, bought router WRT310N... Home trial advocate for the network set in place.  Gave email and pwd HND... went back to HND did not recognize my pwd... .reset and Pwd used sent to me

  - then using the DDT sent to me... HND says it's "..." the terms registered to another user account... " !! Help! I have

  Serial number of 20 letters and numbers with trial version

  * Contact Linksys... they have accessed remotely in and uninstalled LELA and reinstalled and same result cannot change the "young teen" on any one of the connected computers.

  HND said "..". the terms registered to another user account... "Continuous HND if I'm the right user, then reset the router.  Prefer not to reset... Help

  Can you private message me your SN and HND router license.  I'll look it up to see what email address is associated with it.