Ports 10/100/1000 on the cisco 2911 router does support etherchannel

Similar Questions

• The e2000 wireless router does support jumbo frames?

  I can't find (unless I missed it) and in the e2000 on how documentation set sizes of frame of reference.  Is that supported?  If so, what are the steps?

  A fact important is jumbo frames are not compatible at a speed lower than 1000 Mbps

  I think that Linksys E2000 already has Gigabit Ethernet ports.

  And I think that you can change the size of the image on the properties of the Ethernet adapter if the card is a Gigabit Ethernet card.

• How to use Layer 2 Ports on the Cisco 1841 router switch

  Hello

  I use the Cisco 1841 router with a single port layer 3 Fe0 and 8 Ports switched.

  I gave the IP on the Fe0 port which is connected to another router.

  Now I don't know how to use Layer 2 of the router switch ports.

  I tried to make one of the port as a Port of access by switchport mode access and connected my laptop and the same subnet given IP, but I can't ping my Fe0 IP port and vice versa, as I am also unable to ping my laptop router.

  Can someone explain to me how to use these ports on layer 2?

  Hi Muhammadatifmasood, take a look at the link below, I'm sure that you will find it useful.

  https://supportforums.Cisco.com/discussion/10919631/how-enable-routing-b...

  BenSamayoa

• The model Interface Toolkit does support the cRIO-9068 again based on Linux?

  Hello, I have a cRIO-9068 and need to integrate a Simulink model in my controller. The model Interface Toolkit does support the cRIO-9068 again based on Linux? Besides, don't Veristand? This page assumes that it is not:

  http://digital.NI.com/public.nsf/allkb/2AE33E926BF2CDF2862579880079D751

  Thank you

  Hi Southern_Cross,

  Based on the readme:

  http://digital.NI.com/public.nsf/allkb/D3F40C101B66128186257D020049D679

  It seems that it is now supported! These resources should provide a few more details:

  http://zone.NI.com/reference/en-XX/help/374160B-01/vsmithelp/mit_model_support/

  http://digital.NI.com/public.nsf/allkb/E552B0CD4E48215586257DF7005BE055

  Please note that NI VeriStand 2014 can't stand it targets NOR Linux in real time.

  Kind regards

• The Compaq Presario CQ41 does support 64 bit OS?

  I went in a chain retailer and I noticed the Compaq Presario CQ41 was running Windows 7 Home Premium 32 bit, but had 4 GB of RAM installed (which he could not fully use). The stafff I asked why and they said HP/Compaq laptops cannot run 64-bit.

  The Compaq Presario CQ41 does support 64-bit so it can used the entire 4 GB of ram?

  The Compaq Presario CQ41 will also support a 64-bit Windows 7 operating system.

• LAN does not work when the Cisco E1000 router hangs

  Original title: Download sp3

  Remember - this is a public forum so never post private information such as numbers of mail or telephone! I bought recently a new Cisco E1000 router. My computer is a laptop model Lenovo 0769.

  I am running windows XP with sp2. The cisco software requires sp3. I called support of cisco and even they couldn't get to download sp3. My network is wireless on the router and I had to install from another laptop computer on the system. My LAN does not work when hooked. What do you suggest to me.

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Hi mdenrique,

  1. what exactly do you mean by LAN (Local Area Network) does not work? You get the error message?

  If you have not installed Service Pack 3, try the following steps:
  Step 1: Download Service Pack 3
  see How to obtain the latest Windows XP service pack .
  b. scroll the window and click on "Download now the Windows XP Service Pack 3 package" to download the service pack.
  c. save the file on the desktop.

  Step 2: Install Service Pack 3
  a. open the file downloaded and follow the instructions in the wizard to complete the installation.
  b. restart the computer once the installation is complete.

  For more information, see steps to take before you install Windows XP Service Pack 3

  Note: Once you have installed service pack 3, install the router and check if the problem persists.

  Step 3: To troubleshoot LAN, run home and small Office Networking Troubleshooter
  a. Click Start and then click Help and Support.
  b. under Pick a help topic, click Network and Internet.
  c. under network and the Web, click on resolution of networking or Web problems and then click on home and small Office Networking convenience store.
  d. answer the questions in the troubleshooter to try to find a solution.

  For more information, see the following articles:
  1 see How to troubleshoot a network in Windows XP
  2 see two resources to solve the problems of connection network in Windows XP

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Problem starting the Cisco 2821 router

  Hello world

  I have cisco 2821 router. I am facing problem starting.

  someone suggest me what is the problem.

  Thanks in advance...

  VERSION of the SOFTWARE system Bootstrap, Version 12.4 (13r) T, (fc1)
  Technical support: http://www.cisco.com/techsupport
  Copyright (c) 2006 by cisco Systems, Inc.

  The ECC memory initialization
  .
  C2821 platform of 262144 KB of main memory
  Main memory is configured for 64-bit with ECC active

  ReadOnly initialized ROMMON
  load complete, point of entry to the program: 0x8000f000, size: 0xcb80
  load complete, point of entry to the program: 0x8000f000, size: 0xcb80

  load complete, point of entry to the program: 0x8000f000, size: 0x26bc2cc
  Decompression of self-image: #.
  ################################################################################
  ################################################################################
  ################################################################################
  ################################################################################
  ################################################################# [OK]

  Smart init is enabled
  Smart init is sizing iomem
  MEMORY_REQ TYPE ID
  0003E8 0X003DA000 C2821 Mainboard
  1A 0X0025178C E3 0001AB
  0X00263F50 VPN on board
  0X000021B8 embedded USB
  Swimming pools public buffer 0X002C29F0
  Swimming pools public particle 0 X 00211000
  TOTAL: 0X00D65284

  If all memory conditions above are
  "UNKNOWN", you could use a non supported
  configuration or there is a software problem and
  the system may be compromised.
  Rounded IOMEM to: 14 MB.
  Using iomem of 5 percent. [14 mb / 256Mb]

  Legend restricted rights

  Use, duplication, or disclosure by the Government is
  subject to such restrictions as set out in paragraph
  (c) Commercial - limited computer software
  The rights to FAR clause 52.227 - 19 and subparagraph s
  (c) (1) (ii) rights to technical and computer data
  Clause of DFARS 252.227 - 7013 section software.

  Cisco Systems, Inc.
  170 West Tasman Drive
  San Jose, California 95134-1706

  Cisco IOS software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4 T7 (9)
  Version of the SOFTWARE (fc3)
  Technical support: http://www.cisco.com/techsupport
  Copyright (c) 1986-2008 by Cisco Systems, Inc.
  Last updated Friday, January 10 08 16:35 by prod_rel_team
  Image text-base: 0x400B1E74 database: 0x434A9AC0

  ERROR detected on Bus PCI1
  Try REINSTALLING all the modules in the system
  pci1_int_cause 0 x 00000240,
  pci1_err_addr 0 x 00091009, pci0_err_cmd 0x0000000A
  PCI Master Read parity error
  Abort target PCI

  R0 = r1 = r2 FFFFFFFF FFFFFFFF = 0 r3 = 45 80000 r4 = 0
  R5 = 303 r6 = 0 A7 = 1 = 0 = 100000 r9 r8
  R10 = 0 r11 = 465E4369 r12 = 0 r13 = 465E436A r14 = 0
  R15 = r16 r17 8 = 0 = C100 r18 = 0 r19 3400 101 =
  R20 = r21 0 = 40096828 r22 = FFFFFFFF r23 = r24 FFFF00FF = 0
  R25 = 469AAC64 r26 = 0 = 469AAC60 r28 = 0 = 469AAC5C r29, r27
  R30 = 0 r31 = 469AAC58 r32 = r33 FFFFFFFF = r34 = FFFFFFFF FFFFFFFF
  R35 = r36 = r37 = r38 = r39 FFFFFFFF FFFFFFFF FFFFFFFF FFFFFFFF = FFFFFFFF
  R40 = FFFFFFFF = FFFFFFFF = FFFFFFFF = FFFFFFFF r44 r43 r42 r41 = FFFFFFFF
  R45 = r46 = r47 = r48 FFFFFFFF FFFFFFFF FFFFFFFF = r49 0 = 469AACD0
  R50 = 0 0 = 0 r53 r51 = r52 = 3040A 801 r54 = FFFFFFFF
  R55, r56 = FFFFFFFF = FFFFFFFF r58 r57 A000F000 = = 0 = 465E4358 r59
  R60 = r61 = r62 FFFFFFFF FFFFFFFF = r63 = 0 402E4B10
  GENS = 3400 103 mdlo_hi = my 0 = 251 00
  mdhi_hi = 0 = 0 badvaddr_hi = FFFFFFFF mdhi
  BadVAddr = cause = epc_hi 0 = FFFFFFFF FFFFFFFF
  EPC = 402E4B08 err_epc_hi = err_epc FFFFFFFF = FFFFFFFF

  ERR-1-FATAL %: interruption of the fatal error, reload
  err_stat = 0 x 0

  = Posts from Flushing (02: 37:51 UTC Wednesday, may 18, 2016) =.

  Messages in queue:

  02:37:51 UTC Wednesday, may 18, 2016: interrupt exception, signal CPU 22, PC = 0 x 0

  --------------------------------------------------------------------
  Software fault possible. On reccurence, you perceive
  crashinfo, 'show tech' and contact Cisco Technical Support.
  --------------------------------------------------------------------

  -Trace =
  $0: 00000000, AT: 00000000, v0: 00000000, v1: 00000000
  A0: 00000000, a1: 00000000, a2: 00000000, a3: 00000000
  T0: 00000000, t1: 00000000, t2: 00000000, t3: 00000000
  T4: 00000000, t5: 00000000, t6: 00000000, t7: 00000000
  s0: 00000000, s1: 00000000, s2: 00000000, s3: 00000000
  S4: 00000000, s5: 00000000, s6: 00000000, s7: 00000000
  T8: 00000000, t9: 00000000, k0: 00000000, k1: 00000000
  GP: 00000000, sp: 00000000, s8: 00000000, ra: 00000000
  EPC: 00000000, ErrorEPC: 00000000, GENS: 00000000
  MY: 00000000, MDHI: 00000000, BadVaddr: 00000000
  CacheErr: 00000000, DErrAddr0: 00000000, DErrAddr1: 00000000
  DATA_START: 0X434A9AC0
  Cause 00000000 (Code 0 x 0): Exception of interruption

  Writing crashinfo in flash: crashinfo_20160518-023752
  No reboot to warm storage
  System received a system error *.
  signal = 0 x 16, code = 0x0, context = 0 x 46905718
  PC = 0x40096d7c, Cause = 0 x 20, State Reg = 0 x 34008002

  Software Cisco IOS, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4 (9)T7
  Version of the SOFTWARE (fc3)

  OK, the router is running on a train of "T".

  ERROR detected on Bus PCI1
  Try REINSTALLING all the modules in the system
  pci1_int_cause 0 x 00000240,
  pci1_err_addr 0 x 00091009, pci0_err_cmd 0x0000000A
  PCI Master Read parity error
  Abort target PCI

  Remove any all NM/NME or WIC/HWIC cards and restart again.  If the router is able to start properly, upgrade the router to a higher version.  DO NOT use another "T" train if it is needed.  Use instead a train of "M".

• Possibility of SD2008 (8 ports 10/100/1000 gigabit Switch) dismantling Corp. Network

  As long as I log the LAN port will the company network is there any reason to believe that this model of switch or something like that could cause havoc with a corporate network?

  Also, is it possible to connect Http in this switch (is there something in there for settings etc...)?

  Thank you.

  Take two unmanaged switches. Connect two ports of a switch with two ports of the other switch. You have a loop.

  All ports on the SD2008 are the same. There is no difference between them. The SD2008 probably consists of modules of two 4-way internally, which explains why you see these markings on port 1 and 5. You can connect any port you want your ADSL router (you have a router, I hope). There is no segment. All ports can talk to all other ports.

• Supported on the Cisco RV042 router settings

  Hello

  Anyone know if these settings are supported on router CiscoRV042

  shared secret - authentication-

  -AES-256 / SHA1 encryption

  -IKE: Diffie-Hellman (Group 2)

  -Phase 1 IKE every 1440 minutes.

  -The phase 2 (IPsec) all 3600 sec (every hour) of IKE

  Thank you.

  These are all very standard parts of IPSEC.

  See page 45 of the

  http://www.Cisco.com/en/us/docs/routers/CSBR/RV042/Admin/Guide/RV042_V10_UG_C-Web.PDF

  Copied here

  IPSec configuration

  So that any encryption occur, both ends of a

  VPN tunnel must agree on the encryption methods,

  decryption and authentication. This is done by sharing

  a key for the encryption code. Key management, the

  default mode is IKE with pre-shared key.

  Overlay Mode Select IKE with pre-shared key or manual.

  Both ends of a VPN tunnel must use the same mode of

  key management. After selecting the mode, the

  settings available on this screen may change depending

  on the selection you have made. Follow the instructions

  for the mode you want to use. (Manual mode is available

  for VPN tunnels only, no VPN group.)

  IKE with preshared key

  IKE is used to negotiate Internet Key Exchange Protocol

  for Security Association (SA) key material. IKE use it

  Pre-shared key for authentication to the remote peer of IKE.

  The phase 1 DH group Phase 1 is used to create the SA. DH

  (Diffie-Hellman) is a key exchange protocol used for

  Phase 1 of the authentication before establishing process

  pre-shared keys. There are three groups of different premium

  length of the key. Group 1 is 768 bits, and group 2 is 1024 bits.

  Group 5 is 1 536 bits. If the network speed is preferred, select

  Group 1. If it is better to network security, select group 5.

  The phase 1 encryption select an encryption method: SOME

  (56-bit), 3DES (168-bit), AES-128 (128-bit), AES-192 (192-

  ILO) or AES-256 (256-bit). The method determines the

  length of the key used to encrypt or decrypt ESP packets

  AES - 256 is recommended because it is the safest.

  Make sure that both ends of the VPN tunnel using the same

  encryption method.

  The phase 1 authentication select a method of

  authentication, MD5 or SHA. The authentication method

  determines how the ESP packets are validated. MD5 is

  a one-way hash algorithm that produces a 128-bit

  Digest. SHA is a one-way hashing algorithm which produces

  a 160-bit digest. SHA is recommended because it is more

  Fix. Make sure that both ends of the VPN tunnels using the

  same authentication method.

  Phase 1 life time sets the duration of a VPN

  tunnel is active in Phase 1. The default is 28800

  seconds.

  Perfect Forward Secrecy if the perfect forward secrecy

  (PFS) is enabled, the IKE Phase 2 negotiation will be

  generate new key material for encryption of IP traffic and

  authentication, then pirates using brute force to break

  encryption keys will not be able to obtain future IPSec

  keys.

  Phase 2 DH group if the functionality of perfect forward secrecy

  is disabled, then no new key will be generated, so you don't have

  no need to adjust the Phase 2 DH group (the key for Phase 2

  will be the key in Phase 1).

  There are three groups of different main key lengths.

  Group 1 is 768 bits, and group 2 is 1024 bits. Group 5 is

  1 536 bits. If the network speed is preferred, select group 1.

  If it is better to network security, select group 5. You do

  no need to use the same group of DH that you used for

  Phase 1.

  Encryption of the phase 2 Phase 2 is used to create an or

  several IPSec security associations, which are then used to key IPSec sessions.

  Select an encryption method: NULL, (56-bit), 3DES

  (168 bit), AES-128 (128-bit), AES-192 (192-bit) or AES-

  256 (256-bit). It determines the length of the key used to

  encrypt or decrypt packets ESP. AES-256 is recommended

  because it is the safest. Both ends of the VPN tunnel

  must use the same encryption of Phase 2 setting.

  The phase 2 authentication select a method of

  authentication, NULL, MD5 or SHA. Authentication

  method determines how the ESP packets are validated.

  MD5 is a one-way hash algorithm that produces a

  Digest of 128 bits. SHA is a one-way hashing algorithm that

  produces a 160-bit "Digest". SHA is recommended because

  It's safer. Both ends of the VPN tunnel must use

  the same Phase 2 authentication setting.

  Phase 2 HIS life time sets the duration of a VPN

  tunnel is active in Phase 2. The default value is 3600 seconds.

  Pre-shared key that specifies the pre-shared key used

  to authenticate the remote peer of IKE. Enter a key of

  keyboard and hexadecimal characters, for example, [email protected]/ * /.

  or 4d795f40313233. This field allows a maximum of 30

  characters and hexadecimal values. The two ends of the

  the VPN tunnel must use the same pre-shared key. It's

  We recommend that you change the pre-shared

  Key periodically in order to maximize the VPN security.

• Windows 8 don't ask the WEP password when I try to connect to the CISCO WRT120N router

  I am trying to connect to a friends WRT120N router. I click SSID wireless routers, but never, he asks me a WEP password.

  Any help would be appreciated.

  the press right click signal bars network wanted to choose forget this network then reconnect to the network.

• The series Qosmio G20 does support PC2-5300?

  Hello all,.

  For some time now, I've thought about the possibility of an upgrade of RAM for my Qosmio G20 - 126 and all looking for a more economical way than that which is available via the Toshiba site (~ £100 for a 1 GB RAM Module!) I met articles suggesting that the Qosmio G20-126 is compatible with RAM PC2-5300 (333 MHz). To my knowledge the Qosmio G20-126 comes with 2x512MB PC2-4200 (266 MHz) modules installed, in addition to the direct available from Toshiba RAM upgrades are also PC2-4200. So my question for you, former scholars of the Toshiba support forum is simple; my laptop is REALLY compatible with PC2-5300? and if so there will be problems worthy of consideration (i.e. insufficient power supply etc...)?

  Also, I wonder if there are intrinsic advantages regarding the marked Toshiba RAM upgrades available via the site of Toshiba UK. I found the modules of RAM of the similar (at least as far as I can see) specifications for a third of the price. It would be also interesting to note that the model of module of RAM available here on Toshibas website is (according to Google products alias Froogle) same price when buying from third party suppliers (so it's not simply a question of margins exorbitant of Toshiba, unless of course the sellers are also defined on by the aforementioned increases.)

  Sincere greetings,
  Lee Hyde.
  ([email protected])

  Hello

  The Qosmio G20-126 supports a FSB 533 and, therefore, the PC2-4200 DDR2 266 MHz modules are! (DDR2 266 Mhz-> 533 MHz)
  It is absurd to use the RAM PC2-5300 DDR2 333 MHz due to the FSB. You won't see improvements in speed or performance.

  I wonder why you are surprised that Toshiba recommends the use of own products (memory sticks). I think that each manufacture recommend clean products!
  In addition, it is important to mention that brand memory modules are much faster and the performance is much better than the performance and quality of the nameless memory module.

  Of course, you can use all modules that supports hardware specifications, but the don t wonder about laptop performance and memory problems after the use of modules without a name!

  I use the modules of Kingston and I also recommend using these modules, because quality is really nice

• The last version, 23, does support the Roboform toolbar?

  I use my ROBOFORM toolbar every day. If I switch to Firefox 23 going to work again?

  I use the Version of RoboForm 7.9.0.0 and works very well with FireFox 23.0.1

  No problem

• The HP OfficeJet 6700 does support fax through a line of digital phone to StarHub in Singapore?

  I get my phone line at home to Singapore's StarHub over a digital phone network. My HP OfficeJet 6700 will be able to send and receive faxes on this network?

  Hello rabbers,

  Welcome to the HP Forums.

  I see that you do not want to be able to send / receive faxes via Starhub digital voice line.

  Actually, I should say no. This would work sporadically on a digital line, but no guarantee that it will work all the time.  Faxing is intended for older analogue lines and aimed at all ever for digital.

  Here is a link that will give you instructions for setting up the device HP all-in-one to send and receive faxes.

  Thanks for your time.

  See you soon,.

• The UCS B200 M3 does support Windows 2003?

  For compatibility with older existing software, I would know what (assuming that Microsoft extended until 2015 Support contract)

  Kind regards

  Geert

  Hi Geert,

  No, it is not supported.

  http://www.Cisco.com/en/us/products/ps10477/prod_technical_reference_list.html

  Padma

• The extension framework CC does support WebGL?

  Hi all, last time I created extensions for Photoshop was for the beta version of CS4 so much has changed!

  At the time I created a few using Pixelbender effects to create a shader, and then applied to a movieclip and everything was fine.  Even if this was a hack because I wanted to make a glowing sphere, but had to settle for a normal of a sphere of shading map.  I wanted to start where I left off and you just created a quick test Panel, trying to draw a triangle on a canvas with the help of WebGL, but nothing draws in the HTML canvas and me can not see errors in the debug console.

  Any official word on that?  It would bust open a whole bunch of crazy tools if WebGL has been activated.

  On a side note, what is also rendering HTML/javascript engine used in CC?

  TNKS!

  G

  Hello

  You are right. To be precise, we use money chrome embedded framework (CEF) version 1, and later versions will be CEF3.

  V8 powers JavaScript.

  Best regards

  Hallgrimur