3rd interface VLAN does not add properly
Hello
I have some difficulty with a switch 300 series running in mode of L3. I created two VLANS each with an interface IP that work well without any problems. The problem I have is when adding a third interface VLAN and IP - for some reason the switch seems not add the subnet in its routing as a directly connected route table.
The first and second VLAN add correctly. It seems to be the third. I have factory default, the switch and still the same. Version is 1.1.2.0.
The Setup is as follows:
VLAN1 - 10.20.2.253/24
VLAN2 - 192.168.2.253/24
VLAN3 - 192.168.3.253/24
Ping results are:
switch27b42e #ping 10.20.2.253
Ping 10.20.2.253 with 18 bytes of data:
18 bytes from 10.20.2.253: icmp_seq = 1. time = 0 ms
18 bytes from 10.20.2.253: icmp_seq = 2. time = 0 ms
18 bytes from 10.20.2.253: icmp_seq = 3. time = 0 ms
18 bytes from 10.20.2.253: icmp_seq = 4. time = 0 ms
-10.20.2.253 PING Statistics-
4 packets transmitted, 4 packets received, 0% packet loss
round-trip (ms) min/avg/max = 0/0/0
switch27b42e #ping 192.168.2.253
Ping 192.168.2.253 with 18 bytes of data:
18 bytes to 192.168.2.253: icmp_seq = 1. time = 0 ms
18 bytes to 192.168.2.253: icmp_seq = 2. time = 0 ms
18 bytes to 192.168.2.253: icmp_seq = 3. time = 0 ms
18 bytes to 192.168.2.253: icmp_seq = 4. time = 0 ms
-192.168.2.253 PING Statistics-
4 packets transmitted, 4 packets received, 0% packet loss
round-trip (ms) min/avg/max = 0/0/0
switch27b42e #ping 192.168.3.253
Ping 192.168.3.253 with 18 bytes of data:
PING: net-unreachable
PING: net-unreachable
PING: net-unreachable
PING: net-unreachable
-192.168.3.253 PING Statistics-
4 packets transmitted, 0 packets received, 100% packet loss
Additional output which can be interesting:
switch27b42e #show ip int vlan 1
Type of priority status done IP address
Broadcast
------------------- ----------- ---------- ---------- -----------
static 10.20.2.253/24 disable invalid
switch27b42e #show ip int vlan 2
Type of priority status done IP address
Broadcast
------------------- ----------- ---------- ---------- -----------
static 192.168.2.253/24 disable invalid
switch27b42e #show ip int vlan 3
Type of priority status done IP address
Broadcast
------------------- ----------- ---------- ---------- -----------
static 192.168.3.253/24 disable invalid
switch27b42e #show ip route
Maximum parallel paths: 1 (1 after reset)
IP routing: enabled
Code: C - connected, S - static, D - DHCP
C 10.20.2.0/24 is directly connected vlan 1
C 192.168.2.0/24 is directly connected vlan 2
What I am doing wrong?
Thank you in advance.
Craig
Hi Craig,.
I don't think you're doing anything wrong.
The command line shows that this IP for VLAN3 interface is not connected, or at least nothing is connected physically VLAN3.
Connect a PC VLAN3 and see if the interface road happens.
I guess just that nothing is plugged physically vlan3.
regards Dave.
Tags: Cisco Support
Similar Questions
-
My Apple TV remote 3rd generation A1294 aluminium does not work properly, battery is good, and I tried all the resets including factory reset. the battery compartment is clean.
You don't say what you mean by not working not properly, however...
Your Apple TV can become affiliated with another remote control. Hold the remote control close to and pointed on the Apple TV, press and hold the menu and rewind buttons together for 6 seconds or until you see an icon of the chain broken on screen.
-
TEREDO TUNNELING PSEUDO-INTERFACE DEVICE DOES NOT WORK CORRECTLY - ACCORDING TO AVG PC TUNE UP
My laptop is a HP G7030EA - MS Windows Vista Home Basic 32-bit SP2 Intel Pentium Dual CPU T2330 @ 1.60 GHz, 1.0 GB RAM, Mobile Intel 965 Express Chipset Family, bought new in February 2008. I have not changed any hardware, software, etc. I do not use it for games, only for things such as e-mails and visit websites
Until last month when my desktop computer broke, I used the laptop only occasionally as a backup of the computer. It never quite worked and seems to be unable to handle several tasks at once, often taking minutes for Google to load. When I get impatient and click the mouse too much I heard a horrible noise and the screen mouse cursor freeze for a minute or two.
As the laptop has become my main computer at the moment, I downloaded AVG PC Tune Up to see if it would improve it performance has not helped. I was surprised to see how much memory the AVG2013 anti virus program uses, but wonder if the speed of connection and freezing problems I experience result (AVG Tune Up conclusions on) the Teredo Tunneling pseudo-interface unit does not properly.
I follow AVG on screen re boards: looking for a software driver update but none was found, and I got the message "the best driver for your device software is already installed. Windows has determined that the driver software for your device is up-to-date, Tun Miniport, Microsoft Map.
This left me confused. If there is a problem with this device, no solution seems to exist.
Any help that will allow my laptop to function normally is welcome.
I understand that you want to know if the teredo adapter can cause performance problems.
The teredo adapter should not cause performance problems. It is really just used to allow devices work IPv4 with IPv6 Internet service provider. If the ISP was using IPv6 and your system did not have the adapter teredo, so it wouldn't work properly with the service provider. For now, IPv6 is a significant minority that the world continues to work on IPv4 as not all networks, Internet service providers, and businesses are not entirely passed to IPv6.
This thread on the Microsoft forums goes into a little more detail about the adapter teredo including how to disable it so that you only see it in Device Manager. Unless you are using IPv6, this shouldn't really be a problem.
If you start in safe mode, the performance problem persists? Turn on the computer and press F8 once per second for the Mode option, safe mode with networking. This will help you to further isolate the performance problem.
Furthermore, does this happen that the adapter is connected or not?
-
ATI Graphics Driver does not work properly
All of a sudden when I play my games on Facebook my computer completely freezes. Reports error saying that the ATI Graphics Driver does not work properly.
I have checked all the updates of Windows, said that I installed all available updates. Help, please!Hello
First manually check the updated drivers with ATI and ask their support and Forums on all known
questions. Use the methods to update the following drivers.Download the Catalyst Drivers here
http://game.AMD.com/us-en/drivers_catalyst.aspxATI - Forums
http://forums.AMD.com/game/categories.cfm?CATID=260&forumid=11ATI - Support and drivers
http://support.AMD.com/us/pages/AMDSupportHub.aspx============================================================================
Other troubleshooting methods would include the boot minimum and others who might help determine
the cause and eliminate problems.What antivirus/antispyware/security products do you have on the machine? Be one you have NEVER
on this machine, including those you have uninstalled (they leave leftovers behind which can cause
strange problems).----------------------------------------------------
Follow these steps:
Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html==========================================
After the foregoing:
How to troubleshoot a problem by performing a clean boot in Windows Vista
http://support.Microsoft.com/kb/929135
How to troubleshoot performance issues in Windows Vista
http://support.Microsoft.com/kb/950685Optimize the performance of Microsoft Windows Vista
http://support.Microsoft.com/kb/959062
To see everything that is in charge of startup - wait a few minutes with nothing to do - then right-click
Taskbar - the Task Manager process - take a look at stored by - Services - this is a quick way
reference (if you have a small box at the bottom left - show for all users, then check that).How to check and change Vista startup programs
http://www.Vistax64.com/tutorials/79612-startup-programs-enable-disable.htmlA quick check to see that load method 2 is - using MSCONFIG then put a list of
those here.
--------------------------------------------------------------------Tools that should help you:
Process Explorer - free - find out which files, key of registry and other objects processes have opened.
What DLLs they have loaded and more. This exceptionally effective utility will show you even who has
each process.
http://TechNet.Microsoft.com/en-us/Sysinternals/bb896653.aspxAutoruns - free - see what programs are configured to start automatically when you start your system
and you log in. Autoruns also shows you the full list of registry and file locations where applications can
Configure auto-start settings.
http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
Process Monitor - Free - monitor the system files, registry, process, thread and DLL real-time activity.
http://TechNet.Microsoft.com/en-us/Sysinternals/bb896645.aspxThere are many excellent free tools from Sysinternals
http://TechNet.Microsoft.com/en-us/Sysinternals/default.aspx-Free - WhatsInStartUP this utility displays the list of all applications that are loaded automatically
When Windows starts. For each request, the following information is displayed: Type of startup (registry/Startup folder), Command - Line String, the product name, Version of the file, the name of the company;
Location in the registry or the file system and more. It allows you to easily disable or remove unwanted
a program that runs in your Windows startup.
http://www.NirSoft.NET/utils/what_run_in_startup.htmlThere are many excellent free tools to NirSoft
http://www.NirSoft.NET/utils/index.htmlWindow Watcher - free - do you know what is running on your computer? Maybe not. The window
Watcher says it all, reporting of any window created by running programs, if the window
is visible or not.
http://www.KarenWare.com/PowerTools/ptwinwatch.aspMany excellent free tools and an excellent newsletter at Karenware
http://www.KarenWare.com/===========================================
Vista and Windows 7 updated drivers love then here's how update the most important.
This is my generic how updates of appropriate driver:
This utility, it is easy see which versions are loaded:
-Free - DriverView utility displays the list of all device drivers currently loaded on your system.
For each driver in the list, additional useful information is displayed: load address of the driver,
Description, version, product name, company that created the driver and more.
http://www.NirSoft.NET/utils/DriverView.htmlFor drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
Control Panel - device - Graphics Manager - note the brand and complete model
your video card - double - tab of the driver - write version information. Now, click on update
Driver (this can do nothing as MS is far behind the certification of drivers) - then right-click.
Uninstall - REBOOT it will refresh the driver stack.Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party
with their own software and drivers and all other main drivers that you have.Now in the system manufacturer (Dell, HP, Toshiba as examples) site (in a restaurant), peripheral
Site of the manufacturer (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for
BIOS, Chipset and software updates on the site of the manufacturer of the system here.)Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after
each installation.Always check in the Device Manager - drivers tab to be sure the version you actually install
presents itself. This is because some restore drivers before the most recent is installed (sound card drivers
in particular that) so to install a driver - reboot - check that it is installed and repeat as
necessary.Repeat to the manufacturers - BTW in the DO NOT RUN THEIR SCANNER device - check
manually by model.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlIf you update the drivers manually, then it's a good idea to disable the facilities of driver under Windows
Updates, that leaves about Windows updates but it will not install the drivers that will be generally
older and cause problems. If updates offers a new driver and then HIDE it (right click on it), then
get new manually if you wish.How to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx===========================================
Refer to these discussions because many more excellent advice however don't forget to check your antivirus
programs, the main drivers and BIOS update and also solve the problems with the cleanboot method
first.Problems with the overall speed of the system and performance
http://support.Microsoft.com/GP/slow_windows_performance/en-usPerformance and Maintenance Tips
http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/19e5d6c3-BF07-49ac-a2fa-6718c988f125Explorer Windows stopped working
http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/6ab02526-5071-4DCC-895F-d90202bad8b3Hope these helps.
-
Button hardware on Samsung slate Windows 7 does not work properly in Windows 8
After you install the official update of Windows 8, the hardware button windows does not work properly. button lock display as well.
Whenever I restart the system, everything works fine, until you put the sreen of. If you re-enable the slate (just energy), the buttons Don t work.Thus, windows hardware button offers just a double click to change the windows, but doesn´t take you of the subway home and the screen lock work doesn´t button at all.Someone at - it a solution for this problem? Would be nice, because I think that all the samsung slate 7 users have this problem.Hello. I don't know if you have this problem, but as long as no one have answered your question.
I had exactly the same problem and after following the advice of the official windows samsung 8 upgrade support the Tablet worked perfectly.Just follow this link (http://www.samsung.com/us/support/win8upgrade/) and download the software to the 3rd market. It will install a lot of software and hardware upgrade for your Tablet and if it doesn't work as well for me it will solve all your problems. -
I downloaded Multi Access Tool from Mcafee with Firefox Mozilla, how do I reinstall if it does not work properly?
My sincere apologies, my Mcafee came via the Optimum/Cablevision, not Mozilla. I now managed to solve my problem and appreciate the 2 above responses. Thank you.
-
Firefox does not close properly
Hello
A new problem with Firefox occurs today. After turning on my machine, I can open firefox. When I close it, it does not close properly and leaves a firefox.exe running process. I so can not re - open firefox without going into the Task Manager and deleting process. A reboot of my machine did not help
https://support.Mozilla.com/en-us/KB/Firefox%20hangs
See hang-to-output -
Satellite P200 accidents + message: graphic card driver does not work properly
Hello
hope that this issue has not been covered before, but I've owned a Satellite P200 for 3 years now, and this week, it crashes all the time.
When it started going down he gave me a few messages in the sense of "your graphics card/driver does not work properly and windows will be arrested to avoid damage.
It has progressed to the point where now when I turn it on, I have vertical lines running down the screen and the screen flashes on and outside. Within 20 seconds, it restores the BSOD - 'there was a problem and windows will be arrested. Error Page_Fault_In_Non_Paged_Area"then stops.
I ran a system restore but the problem remains.
I have a feeling that my graphics card is toast. Is this good? Are there any other options to try? Thanks in advance for any answers.
Matt
Hello
Sounds like the GPU problem.
But try the graphics card driver update.
Use the most recent driver for your graphics card.In addition, clean the fans of portable computers.
Dust and debris could prevent the cooling fans to turn with the best speed and this could lead to a higher temperature which would lead to overheating.
Use a jet of compressed air. I also use it and it helps to get rid of dust and debris.If this is not enough, then a problem of graphics chip would be possible.
-
Satellite L775 - mouse pad does not work properly
I have a laptop Toshiba Satellite L775. I run Win 7 Home Premium. My mouse pad does not work properly. I also have a Logitech Anywhere MX wireless mouse. I tried the mouse pad to work properly with the key FN and F9, but it does not work. And you really have no idea if that turns or out of the mousepad anyway, subj for another time I guess.
What does not work, but I have to do is to go to Control Panel then mouse option load that and just scroll the tabs without changing what each time and then close and the touch pad works. But only for this session. If I have my laptop nearby, or turn it off, I have to start throughout the whole process.
What's past and how to fix this?
Thank you very much.
> What's past and how to fix this?
After reading your ad, I still don t know what is your problem.
> My mouse pad is not working properly
How to understand this? What does not work properly? What happen exactly when you start your laptop? -
Satellite Pro M10 - infrared does not work properly
Hello
I have a Satellite Pro M10 and my infrared does not work. I downloaded the zip file with the drivers from this site. Then, I uninstalled and reinstalled, but it always happens in the Device Manager under "unknown - SMC IrCC - Fast Port infrared (IR Module: HP). (with an exclamation point). When I look at the properties it says under device status:
This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)
Click Troubleshoot to start the troubleshooter for this device.
However, under Driver Details is said:
C:\windows\system32\DRIVERS\smcirda.sysI extracted the zip file in my home directory of c:\downloads\infrared.
whatever I do, it does not now. It worked when I bought it, but I have too many things on the system for a new installation. Which brings me to another question. Is it possible to re - install windows without losing all your data, etc.? I did it with other systems (95,98) Windows. But it seems that the Toshiba recovery disc means any wiping.Thanks in advance for any help.
ChrisHello
If your HARD disk contains two partitions and you have saved the data on a second you can reinstall the operating system on the first partition using recovery DVDs.
-
Mat * one years (uj-840) DVD player does not work properly
The Mat * one years (uj-840) DVD player does not work properly.
A symptom of the problem is that the icon does not appear in 'my computer '.
more and she does not recognize the CD.I went to the properties of the drive through Device Manager and saw the following message is displayed:
"Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39)
Click Troubleshoot to start the troubleshooter for this device. »Following the instruction of the troubleshooter, I tried to update my driver through
Device Manager, but it tells me that the current driver is the more up-to-date version.
In the properties of the drive, I found that my driver version is: 5.1.2535.0What is a simple problem that has a solution?
I don't see other actions to find the root of the problem.Thank you
I hope this article can help you - http://aps2.toshiba-tro.de/kb0/FAQ8101LA0000R01.htm
Check it out! -
Satellite C - DVD tray does not open properly
My Satellite C DVD tray does not open properly. It opens only after several times.
Can someone help to solve the problem?
Thank you very much
Dalug22Please check this thread:
https://Forum.Toshiba.EU/showthread.php?82344The ODD (optical disc) contains a small ejection hole. You can insert an object like a paper clip to open the ODD plateau
-
Toshiba common modules does not work properly
Whenever I connect to the laptop, I get a message: Tfncky: Toshiba common modules does not work properly.
Anyone know what this means?
I wonder if that has something to do with my windows media player does not properly. If I open the application, it is not to maximize the screen shows the taskbar
Finally, it simply says "not responding" and I have to close the application. Tried to remove and reload that a new copy of WMP but it does not help.I don't know what laptop mode you but the first thing to do is to reinstall the Toshiba common modules.
Please visit Toshiba support and download page under http://eu.computers.toshiba-europe.com go to the download section, choose your phone model and download common modules.Please let us know if everything works well again.
-
Skype does not load properly and leaves no connection either.
Hello.
I recently installed Skype 6.21, however it does not load properly. And it won't let me log in either. I tried to uninstall and reintsalling but still the same. No idea what is the problem? Here's a screenshot of it
Your image is not yet visible. It may take a while before this image is approved by one of the moderators of the community.
You see something similar to this?
-
Keyboard does not work properly
Hello
I had trouble getting my laptop satellite to initialize. Recovery disks & pressing F keys weren't working so I decided to open the laptop to see if there are any loose connections. To my surprise, the laptop seems to work again once I had the USB keys and put back them in! Unfortunately, before that I did, I opened the keyboard and peeked inside.
When I booted up and tried to use the keyboard keys half of their work and the other half seem to think that they represent two other keys for example if I type the letter 'E' I get '3' and '-' as a whole. After 5-10 minutes the entire keyboard will become totally unresponsive until I restart again. Of course, I think I've done something here because this problem since I opened the bottom of the keyboard. This could be a hardware failure I have caused or is anyway that this issue can be resolved without replacing anything?
Thank you very much
Tom
Hi Tom
Theoretically, it might be just a connection lost between the keyboard and the motherboard, but I'm afraid, it can be a serious problem of m.
Maybe you have damaged the connector of the keyboard cable or something similar, and not the keyboard does not work properly.I think the keyboard needs to be replaced to check if only this part is affected
Maybe you are looking for
-
It's something that started recently... tell a month ago. I sent 2 less than 600 KB images which were divided into 3 groups, I guess by firefox. When the email arrived, they were not photos but the numbers. Previously, I had sent pictures of several
-
Can Tecra S10 - I use DVI on a docking station?
I have a Tecra S10 and I would like to know if the DVI port, to a station host (or Port Replicator) can be used, because the Tecra S10 has only a VGA port.
-
delete or reset a password restriction.
Hi my name is Shannon Bird and I recently bought an iphone 4 32 g iphone and there is a restriction functions blocking code passwoed as active WiFi ect. . Is there a way to reset or remove this restriction password.
-
Version of ScriptDefault specific folder location
Hi all. Just a quick question on the scriptdefault.vbs file. In what version the file move in ProgramDrv & AddInfo file in the folder ProgramDrv & Libr\Documents? I work with a base of users spanning several versions so I would like to know. Thank
-
How to change the print in grayscale settings
Any ideawhy my printer is now set to gray scale cannot find a B & W setting. Thank you. Original title: printers