5508 & 4400

Similar Questions

• 4400 and 5508

  I have a 4402 and 5508 times code v7 running, are compatible if used as primary and secondary controllers?

  Thank you

  Jason

  Yes, running the same code they are compatible according to the features you use.

  For example OEAP is supported only on the 5508, so any OEAP would not connect to a x 440

  See you soon,.
  Steve

  --

  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

• How to connect wlc 5508 on 2 switches for redundancy

  Hi, I'm planning implementation of WLC5508, but in the documentation is not clear how to connect WLC5508 to two chassis for redundancy. I do it with WLC4404, where I have the opportunity to choose the primary and secondary port for the management interface. I understand that in 5508 management interface is not mapped to any port.

  You can always set the primary/secondary ports as long as you have not enabled lag. If you try to use two different switches so you should not LAG have enabled anyway (unless it is a battery 3750 or vss)

  You can always set several AP-managers as well.  By default, the management interface is an ap - manager, but he will not be an ap-Manager on the port of relief if you have a defined ap-Manager for the port...   Make sense?

  Just think of the 5508 ports defined as a 4400, except that you don't have to have a Manager AP for each port, unless you want a...

• 3500th and 4400 WLC

  I find contradictory documentation; the 3500th is supported on the WLC 4400 w / version 7.x code?

  Docs, I found say 3500 is CAPWAP only so that only the 5508 CAPWAP.

  Thank you.

  Anything over version 5.2 software WLC > CAPWAP

  Anything below version 5.2 software WLC > LWAPP

  Now go back to 3500th... version minimum necessary to get the 3500 AP with WLC is 7.0 and 7.0 is compatible with the 4400... That is why 3500 is supported on 4400 running the WLC version 7.0 and later...

  This has answered your qiestion?

  Concerning
  Surendra

• Cisco 5508 wlc mesh SSID broadcast?

  Hello

  I feel a strange phenomenon in my environment. Users on computers laptops Windows seem to be trying to connect to the SSID, they see the arrival of an access point which is mode bridge (and not broadcasting an SSID). I confirmed that nothing weird happens where the bridge would be broadcast SSID (standing right next to the newly imaged bridge on a laptop and when I connect I continue straight to a properly configured flexconnect AP).

  There is no output from the path of the box in Windows to tell the operating system that an access point is not valid once he thinks he is, so I'm reaching out to the community to see if someone else has seen this before. My next troubleshooting step is to bridges in stand-alone mode, if I can't find an answer.

  The environment consists of a WLC HA pair, standard 5508 flexconnect environment internal wireless, and we have a pair of bridge linking the two buildings. The affected computers are Windows 7 and Windows 8

  Hello

  Are you sure the mesh, access point is not configured to announce the WLAN of concern?

  Unless it is in a group of AP with no WLAN, WLAN 1-16 will be announced via its interface 2.4 ghz (and 5 GHz so "mesh access customer backhaul" is enabled).

  Here's a controller cli command to confirm (1550 is the AP name) ("site name" is the ap group)

  (jk-4400-111) > show ap WiFi 802. 11 b 1550

  Site Name........................................ 1550
  Site description...

  WLAN ID BSSID Interface
  -------         -----------        --------------------------
  18 management 88:f0:77:b7:b2:20
  management 88:F0:77:B7:B2:21 19

• Toshiba 4400 KE - download does not work - the page does not exist

  I bought a blu - ray Toshiba 4400 ke, which is smart TV. I have connected to the internet as youtube see preinstalled applications. But when I try to download, it tells me that the page does not exist and cannot enter cloud tv.

  I hope you can help me.
  Thank you

  Do you use the internet via LAN cable connection?
  Are you sure that you have configured the network settings correctly (network password)?

  I have a device similar to the House. It is not a Toshiba but the principle remains the same and network configuration is easy and I didn t notice any problem.

• 4400 Workstation XW - cannot find the graphics driver

  Paul Tikkanen advised me to ask here for help about this problem.

  The pc is a Workstation XW 4400 (PW375ET), with Windows XP SP3 and the .net framework 4.0 installed (I don't know if it's relevant). There are some old looking for graphics card plugged into the motherboard with the name written on it of MATROX (Paul says it's a Matrox G200 according to the ID of the hardware) but this ("this Setup program does not detect a supported by this software Matrox graphics card') or all the other drivers that I found do not work.

  Is the hardware id

  PCI\VEN_102B & DEV_2538 & SUBSYS_0947102B & REV_02

  Maybe someone here can help.

  with sincere friendships.

  Naim Saari

  Helsinki, Finland

  Googling "PCI\VEN_102B & DEV_2538 & SUBSYS_0947102B & REV_02" gave a few sites and after a minutes to read (but not to download anything I have concerns on part 3 pilot sites), I found that the card is a Matrox Parheila AVPe.

  Googling "Matrox Parheila AVP" is the Matrox product to this map page. After a few minutes navagating on this site, you can find the XP driver for this card. There are 3 of them, but the last driver HF dated May 8, 2007 is probably the right to choose, it is the 1.13.00.158 HF version and supports XP and VISTA.

  To obtain the driver, start http://www.matrox.com/graphics/en/products/legacy/parhelia/parheliaapve/ , and then click Driver and software in the left pane. Click on Parhelia Series then check Parhelia APVe and press Next. Click Next and drivers of Windows XP (or the required operating system), and then click Next. This should give you the necessary driver selection page and it should be obvious what to do next...

  But note the message on the download page of the driver on the removal of the old driver before you install the new driver...

• HP Pavilion G6-2146sl: white screen after upgrading an AMD A6 - 4400 m for an AMD A10 - 5750 m

  Hi all, I upgraded my HP Pavilion G6-2146sl of the A6 - 4400 m for the A10 - 5750 m, but when I turn on the PC, the screen stays black and nothing happens. What can I do? Thanks in advance.

  Everyone here said it that this processor work? It is not listed in the manual and is incompatible just pure and simple. It will never work on this motherboard. Here is the Manual:

  Manual

  Top of page compatible processor is

  CPU AMD® A10 - 4600M (3.2 GHz/2.3 GHz, 1 600 MHz/4.0 MB L2 cache, DDR3, quad core, 35W)

  I hope that you can exchange it for one that will work. Post back with more questions.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Series of HP Pavillion 4400 running windows xp home edition

  I have just perchased a 4400 of Laptop HP Pavillion running windows xp home edition online ongoing series. I have not yet received. The person says he has a problem with him saying: "the operating system not found '. What can I do to solve this problem.

  It probably means that you need to replace the hard drive. For a full explanation of possible causes and resolution of this error, see This Microsoft Support article.

• A capacitive stylus will work on a HP tc 4400

  I have a HP tc 4400 tablet labtop and I want to know if a capacitive stylus will work to place a digital pen?

  Hello

  Given that the problem is related to the capacitive stylus HP TC 4400, I suggest that get you in touch with HP support for assistance.

  It will be useful.

• Need help to update the graphics drivers for my Intel HD 4400

  Hello. I have an Aspire V5-561-6607 Windows 8.1 running with a chart Intel HD Graphics 4400 card.

  I have the latest drivers OEM of the Acer Web site. However, they are NOT the latest Intel drivers for the 4400 HD.

  I can't upgrade any more than the Acer drivers, despite the Acer drivers being obsolete.

  Is there something I can do? I know HOW to update the drivers, I can't just - when I try to manually update the drivers through the utility Intel it seems to think that Acer drivers are the absolute latest. Period.

  It raises questions for the games should not be a problem with, and I want to solve this problem.

  check if all entries is on/features of the program, if there is no evidence of installation, go to Device Manager, right-click on the Intel VGA adapter and select uninstall, if he asks me to remove the software drivers, check out the options and uninstall.

• HP Pavilion 4400 series

  I have a HP Pavilion 4400 series laptop and when I turn it on it shows a black screen and the lights flash and there is a noise of rattling coming from him. What should I do to fix this?

  This could be your drive hard giving you the question. A bad hard drive sometimes results in a black screen. First, try these steps.

  Try testing the hard drive.  http://support.HP.com/us-en/document/c00439024

  If this does not remove the hard drive.

  https://www.YouTube.com/watch?v=y6agiCGktwA

  Then test it again.  http://support.HP.com/us-en/document/c00439024

  Let me know if she lets you in the BIOS.

  If this isn't the case, it could be the motherboard that gives you the question.

• which chipset driver do I need for a dell dimension 4400 pentium 4

  which chipset driver do I need for a dell dimension 4400 pentium 4

  Go to Dell support and enter your Number of Dell Service.

  That's probably the one--> http://tinyurl.com/3o8v73b

• 4400-110 a error code

  My Dell Inspiron crashes when you enter the logon password.

  After you run the Dell dignostics, I get the following error message:

  4400-011 a error code

  MSG: SCSI_0 - 000_DISK_0_:_MULTI - CARD - only target not ready

  I have rtied the Dell and Microsoft, sites but could not find a reason or a response.

  Can anyone help?

  Hi amadouwone,

  I suggest you follow the method and check if it helps.

  Do a check disk and check if it helps.

  How to perform a disk check?

  Note: When running chkdsk on the drive hard if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.

  If the problem persists, contact the manufacturer of your computer and check if that helps.

  http://support.Dell.com/support/DPP/index.aspx?c=us&l=en&s=DHS

• Can upgrade you Dell Dimension 4400 to Vista/WIN7

  Can upgrade you Dell Dimension 4400 in Vista/WIN7?

  Meet the system requirements? If Yes, you can purchase Windows 7. If not, stick with XP.

  Windows 7 system requirements

  If you want to run Windows 7 on your PC, here's what it takes:

  • 1 gigahertz (GHz) or faster 32-bit (x 86) or (x 64) 64-bit processor

  • 1 gigabyte (GB) of RAM (32-bit) or 2 GB RAM (64-bit)

  • 16 GB of disk space available (32-bit) or 20 GB (64-bit)

  • Graphical device DirectX 9 with WDDM 1.0 or higher driver

  "A programmer is just a tool that converts the caffeine in code" Deputy CLIP - http://www.winvistaside.de/