5548 standalone PE & PE 5548 battery Raccordementvia SPF 10 G +.

Similar Questions

• STP and PowerConnect 5548 battery

  HELO,

  I have 2 switches in the stack with HDMI mode. I use these two switches in the access layer.

  To connect to the distribution layer, connect to a switch to a distribution layer and unit 2 to another different switch of the distribution layer.

  Configure ports in the trunk, but I can not activate PLEASE.
  Everything is configured with the same VLAN and the connection works. But the two ports (unit 1 and unit 2) are forwarding.

  I have no other battery that switches PowerConnect and working properly.

  The HDMI connection is in the tree covering weight? or is it just for internal use, the two switches?

  Thank you

  concerning

  The HDMI ports for stacking are not involved PLEASE. When the switches are stacked, they are managed as a single unit.

  I wanted to clarify, when you say that you cannot enable STP, does that mean you don't want STP is enabled? Or, when you try to activate PLEASE, it gives an error / will not?

  You mentioned that ports 1 and 2 remain in a State of shipping, it's the desired status? What status you are waiting for and why?

  Thank you.

• 5548 stack and LACP

  Hi all

  First post here; so I'm sorry if I'm in the wrong thread...

  I inherited a bunch of 5548.

  I have two "stacks"; a stack of three (3) devices and another battery of two (2) devices.

  The stack of three is a cluster VM and the stack of the two is the network/IDF.

  On the side of the IDF, I have this:

  !
  interface gigabitethernet1/0/43
  Description 'link to 5548 vmstk.
  Auto mode channel-group 6
  !
  interface gigabitethernet1/0/44
  Description 'link to 5548 vmstk.
  Auto mode channel-group 6
  !
  interface gigabitethernet1/0/45
  Description 'link to 5548 vmstk.
  Auto mode channel-group 6
  !
  interface gigabitethernet1/0/46
  Description 'link to 5548 vmstk.
  Auto mode channel-group 6
  !
  interface gigabitethernet1/0/47
  Description 'link to 5548 vmstk.
  Auto mode channel-group 6
  !
  interface gigabitethernet1/0/48
  Description 'link to 5548 vmstk.
  Auto mode channel-group 6
  !

  and in the vmstack I have this:

  dl5548-vmstk # sh running-config interface gigabitethernet 0/1/47-48
  interface gigabitethernet1/0/47
  Description 'link to 5548-stk.
  Auto mode channel-group 6
  !
  interface gigabitethernet1/0/48
  Description 'link to 5548-stk.
  Auto mode channel-group 6
  !
  dl5548-vmstk # sh running-config interface gigabitethernet 0/2/47-48
  interface gigabitethernet2/0/47
  Description 'link to 5548-stk.
  Auto mode channel-group 6
  !
  interface gigabitethernet2/0/48
  Description 'link to 5548-stk.
  Auto mode channel-group 6
  !
  dl5548-vmstk # sh running-config interface gigabitethernet 0/3/47-48
  interface gigabitethernet3/0/47
  Description 'link to 5548-stk.
  Auto mode channel-group 6
  !
  interface gigabitethernet3/0/48
  Description 'link to 5548-stk.
  Auto mode channel-group 6
  !

  I'm looking for validation that this is a valid config...

  vmstk item in gi1/0/47-48 goes to idfstk item in gi1/0/43-44

  vmstk gi2/0/47-48 goes to idfstk item in gi1/0/45-46

  vmstk IG3/0/47-48 goes to idfstk item in gi1/0/47-48

  vmstk [1,2,3] are connected via hdmi cables stackable...

  Should I have a separate for each switch port-channels?

  Is the same port on each switch of vmstk channel a problem?

  Is this a SMLT/STI problem? (http://en.wikipedia.org/wiki/Link_aggregation and http://en.wikipedia.org/wiki/IEEE_802.3ad)

  SH interface counters port-channel 6

  on both devices shows no error...

  Thanks in advance.

  All these counters seem to be good. What config looks like the Group 6 of the chain?

  Have we not different cables, that we can try with the channel group? See if that makes a difference on ports going up and down.

  Configuration changes made during the timestamps in the newspapers?

  Thank you

• Creation of the VLAN between Powerconnect 5548 and F10 s4810...

  In the coming months we will replace our network equipment.  I was able to get their hands on the new gear at the beginning, and if I'm not traditionally a guy from the network, the project has been given to me and I started playing.  The first thing that I wanted to work on was implemented VLANs.  I have configured the switches like the picture below:

  

  When I have IP every PC connected to the same subnet and apply VLAN10 to their respective ports, they aren't to pings within the same stack or between cells.  My basic understanding is that they are, do they not?  Did I miss something in my understanding of VLANS or is there a problem with my configs?  I posted the configs below.

  RTTMOACCESS01 config:

  database of VLAN
  VLAN 10,20,30,40,50
  output
  Add a voice vlan Yes-table Nortel___ 000181
  Add a voice vlan Yes-table 0001e3 Siemens_AG_phone___
  Add a voice vlan Yes-table 00036 b Cisco_phone___
  Add a voice vlan Yes-table 00096e Avaya___
  Add a voice vlan Yes-table 000fe2 H3C_Aolynk___
  Add a voice vlan Yes-table Shoretel___ 001049
  Add a voice vlan Yes-table 0060 b 9 Philips_and_NEC_AG_phone
  VLAN voice Yes-table add 00907 Polycom/Veritel_phone___
  Add a voice vlan Yes-table 00e0bb 3Com_phone___
  860 port address 0.0.0.0 iSCSI target
  port 3260 address 0.0.0.0 iSCSI target
  port 9876 address 0.0.0.0 iSCSI target
  port 20002 address 0.0.0.0 iSCSI target
  20003 port address 0.0.0.0 iSCSI target
  port 25555 address 0.0.0.0 iSCSI target
  hostname rttmoaccess01
  no console logging
  privilege 15
  !
  interface vlan 10
  Name IT
  !
  interface vlan 20
  name UserPCs
  !
  interface vlan 30
  name UserTCs
  !
  interface vlan 40
  the voice name
  !
  interface vlan 50
  Name printers
  !
  gigabitethernet1/0/1 interface
  switchport access vlan 10
  !
  tengigabitethernet1/0/1 interface
  switchport mode general
  switchport general allowed vlan add 10 tag
  switchport general allowed vlan add 20 tag
  switchport general allowed vlan add 30 tag
  switchport general allowed vlan add 40 tag
  switchport general allowed vlan add 50 tag
  !
  gigabitethernet2/0/1 interface
  switchport access vlan 10
  !
  tengigabitethernet2/0/1 interface
  switchport mode general
  switchport general allowed vlan add 10 tag
  switchport general allowed vlan add 20 tag
  switchport general allowed vlan add 30 tag
  switchport general allowed vlan add 40 tag
  switchport general allowed vlan add 50 tag

  !
  Default settings:
  Service etiquette: 76BYTS1
   
  SW version 4.1.0.8 (28 August 2012 time 11:17:36)
   
  Gigabit Ethernet ports
  =============================
  Speed 1000
  full duplex
  negotiation
  flow control
  Auto MDIX
  no back pressure
   
  interface vlan 1
  interface port-channel 1-32
   
  spanning tree
  spanning tree mode RSTP
   
  basis of QoS
  QoS trust cos
  Enable IAS

  RTTMOACCESS02 config:

  database of VLAN
  VLAN 10,20,30,40,50
  output
  Add a voice vlan Yes-table Nortel___ 000181
  Add a voice vlan Yes-table 0001e3 Siemens_AG_phone___
  Add a voice vlan Yes-table 00036 b Cisco_phone___
  Add a voice vlan Yes-table 00096e Avaya___
  Add a voice vlan Yes-table 000fe2 H3C_Aolynk___
  Add a voice vlan Yes-table Shoretel___ 001049
  Add a voice vlan Yes-table 0060 b 9 Philips_and_NEC_AG_phone
  VLAN voice Yes-table add 00907 Polycom/Veritel_phone___
  Add a voice vlan Yes-table 00e0bb 3Com_phone___
  860 port address 0.0.0.0 iSCSI target
  port 3260 address 0.0.0.0 iSCSI target
  port 9876 address 0.0.0.0 iSCSI target
  port 20002 address 0.0.0.0 iSCSI target
  20003 port address 0.0.0.0 iSCSI target
  port 25555 address 0.0.0.0 iSCSI target
  hostname rttmoaccess01
  no console logging
  privilege 15
  !
  interface vlan 10
  Name IT
  !
  interface vlan 20
  name UserPCs
  !
  interface vlan 30
  name UserTCs
  !
  interface vlan 40
  the voice name
  !
  interface vlan 50
  Name printers
  !
  gigabitethernet1/0/1 interface
  switchport access vlan 10
  !
  tengigabitethernet1/0/1 interface
  switchport mode general
  switchport general allowed vlan add 10 tag
  switchport general allowed vlan add 20 tag
  switchport general allowed vlan add 30 tag
  switchport general allowed vlan add 40 tag
  switchport general allowed vlan add 50 tag
  !
  gigabitethernet2/0/1 interface
  switchport access vlan 10
  !
  tengigabitethernet2/0/1 interface
  switchport mode general
  switchport general allowed vlan add 10 tag
  switchport general allowed vlan add 20 tag
  switchport general allowed vlan add 30 tag
  switchport general allowed vlan add 40 tag
  switchport general allowed vlan add 50 tag
  !
  Default settings:
  Service etiquette: 76BYTS1
   
  SW version 4.1.0.8 (28 August 2012 time 11:17:36)
   
  Gigabit Ethernet ports
  =============================
  Speed 1000
  full duplex
  negotiation
  flow control
  Auto MDIX
  no back pressure
   
  interface vlan 1
  interface port-channel 1-32
   
  spanning tree
  spanning tree mode RSTP
   
  basis of QoS
  QoS trust cos
  Enable IAS

  Config RTTMOCORE

  ! Version 8.3.12.0
  ! Last modification of the configuration to Fri Jun 14 13:31:58 2013 default
  ! Startup-config updated Fri Jun 14 13:32:40 2013 default
  !
  start the primary system battery-unit 0: A:
  start a system secondary battery-unit 0: B:
  start the system stack-unit 0 default: A:
  start the primary system battery-unit 1: A:
  start a system secondary battery-unit 1: B:
  start the system default stack-unit 1: A:
  !
  redundancy full automatic synchronization
  !
  Hardware watchdog
  !
  no console logging
  !
  hostname rttmocore
  !
  disposal of battery-unit 0 S4810
  !
  stack-unit 0 battery-group 14
  !
  stack-unit 0 battery-group 15
  !
  interface TenGigabitEthernet 0/46
  no ip address
  switchport
  FlowControl rx tx off
  no downtime
  !
  interface TenGigabitEthernet 0/47
  no ip address
  switchport
  FlowControl rx tx off
  no downtime

  disposal of battery-unit 1 S4810
  !
  stack stack-unit 1-group 14
  !
  stack stack-unit 1-group 15
  !
  interface TenGigabitEthernet 1/46
  no ip address
  switchport
  FlowControl rx tx off
  no downtime
  !
  interface TenGigabitEthernet 1/47
  no ip address
  switchport
  FlowControl rx tx off
  no downtime
  !
  !
  interface Vlan 1
  !
  interface Vlan 10
  Description IT
  Name IT
  no ip address
  Tagged TenGigabitEthernet 0/46-47
  Tagged TenGigabitEthernet 1/46-47
  Shutdown
  !
  interface Vlan 20
  Description UserPCs
  name UserPCs
  no ip address
  Shutdown
  !
  interface Vlan 30
  Description UserTCs
  name UserTCs
  no ip address
  Shutdown
  !
  interface Vlan 40
  Speech description
  the voice name
  no ip address
  Shutdown
  !
  interface Vlan 50
  Printers description
  Name printers
  no ip address
  Shutdown
  !
  Lldp Protocol
  !
  0 line console
  line vty 0
  line vty 1
  line vty 2
  line vty 3
  line vty 4
  line vty 5
  line vty 6
  line vty 7
  line vty 8
  line vty 9
  !
  end

  I would say lets start with one side and obtain communication of work between the two computers on the same stack at RTTMOACCESS01. The port settings for the 1/01 and 2/01 look great both in access mode for VLAN 10. Which IP addresses and subnets you assign to computers?

  5548 to battery power battery connection 10 also appear to not be in a LAG, then we run two connections like that and they aren't in a SHIFT, we create a loop and a single connection will enter a blocking state.

  For the connections between the 5548 and force 10, I suggest to turn them into a GAP. The command should look like this.

  Console > activate

  Console # configure

  Console (config) # (config) # interface tengigabitethernet 1/0/1

  Console (config) # port - 1 automatic mode group

  output console #.

  Console (config) #.

  Do the same for Te2/0/1

  Then we set up this OFFSET to set it up, and I would try to use the trunk instead of general mode mode.

  Console (config) # interface port-channel 1

  console switchport mode trunk #.

  console # permit trunk switchport vlan add 10,20,30,40,50 tag

  The same should be done for the Force switch 10.

  Te0/46.1/46 in a SHIFT

  Te0/47.1/47 in another SHIFT

  Put in the trunk and let the VLANS on the trunk.

  Allows to study these settings and see if we can make any progress.

  Thank you

• Need help to buy PowerConnect 5548 or 6248

  I currently Powerconnect 6248 and 6224 switches via my network.  On a floor 48 port switch is full and I need to add another, my thought is to add an another 6248 and stack them, but told me that I should get the 5548 and use sfp + 10 gig connection to connect to my 6248.  When I talked to my rep at Dell, he said he would not recommend it, but it might be possible.  Can someone tell me what would make the most sense?  Currently, we have data on the site servers and applications but will move them to a data center in the near future.

  The first thing that comes to mind would be to run as two stacked 6200 switches. When stacked it management makes it a little easier since the stacked switches act as one. It also less time spent on configuration with the addition of a member of the battery compared to a separate switch. Once 6200 switches are stacked you would also have the ability to Setup redundant connections by implementing a SHIFT that uses a port to each of the switches.

  On the other side of things, I'm not familiar with the topology of your network. So there may be a specific situation that is the reasoning behind this recommendation of people. They gave no explanation of why they would recommend the 5548 with connection sfp + on the stack?

  Thank you

• Details of graphics card (5548) Dell Inspiron 15

  I recently bought a dell inspiron 15 (5548) and now im faced with somewhat misleading of the problem with the graphics card. Is - this m265 R7 or R7 m260?

  Latest drivers Dell show as m265, but the games stuck and completely non playable after the A06 bios update. Latest drivers from AMD say good race his m260 and games (ex: CS: go to 45-55 fps).

  Also when buying the guy from the dell store said m260 / m265 is a dedicated graphics card and this message says that it is not, rather, it is just a rendering engine. Thus, evrything goes through processor again and so on...

  Could someone sort this point for me coz its nowhere mentioned on the page of the product it's a converter card. Also when you guys will fix that issue drivers? It is 260 or 265 or just a problem of labelling? IM currently with AMD drivers and it just works.

  Idk it I can post my service here tag. Answer me if its ok.

  I need answers guys...

  The system uses the hybrid video controlled by software.  Only the Intel GPU has a connection to display - all passes video through it on its way to the screen, even if it was made by the AMD GPU.

  Virtually all systems of low - medium range now work this way.  If you need true GPU support, discreet, it is the province of high-end Alienware and Precision mobile workstations.   That's all as many competing systems from other manufacturers.

• Is the spanning tree bpdu filtering on the 5548 "bpdufilter default spanning-tree portfast'

  It seems to me as "the protocols spanning-tree bpdu filtering" on the 5548 the same "spanning-tree portfast default bpdufilter" on the switches of the series N - is that correct?  If this is not the case, what is the equivalent command to 'spanning-tree portfast default bpdufilter?

  Ken

  They lead to the same result, just with a little different method. N-series bpdufilter search all ports configured for portfast and disables the transmission and reception of BPDUS on these interfaces. With the looks of 5548 bpdufiltering for ports with covering weight tree disabled. There is not a command on the 5548 that will search interfaces in portfast mode and filter the BPDU.

• 7048 routing/DHCP relay with 5548

  Hello

  I have a problem with the 5548 do not relay the query DHCP for PXE (SCCM), 5548 is connected to 7048 (trunk). We shop Cisco, this is the first time that I am using DELL. Any help is appreciated.

  --------7048--------
  
  !Current Configuration:!System Description "PowerConnect 7048, 4.2.2.3, VxWorks 6.6"!System Software Version 4.2.2.3!System Operational Mode "Normal"!configuregvrp enablevlan databasevlan 2,10-11,21,50-52,156vlan routing 1 1vlan routing 10 2vlan routing 21 3vlan routing 50 4vlan routing 51 5vlan routing 52 6vlan routing 156 7vlan routing 2 8vlan routing 11 9vlan association subnet 10.112.0.0 255.255.252.0 10vlan association subnet 10.112.4.0 255.255.255.0 11vlan association subnet 10.116.4.0 255.255.252.0 21slot 1/0 5    ! PowerConnect 7048slot 1/1 11   ! SFP+ Cardslot 1/2 9    ! CX4 Cardslot 2/0 6    ! PowerConnect 7048Pslot 2/1 11   ! SFP+ Cardslot 2/2 9    ! CX4 Cardstackmember 1 5    ! PCT7048member 2 6    ! PCT7048Pip routingip route 0.0.0.0 0.0.0.0 192.168.1.58ip route 10.0.0.0 255.0.0.0 192.168.1.58interface vlan 1exitinterface vlan 2ip address 192.168.1.57 255.255.255.252ip local-proxy-arpno ip redirectsexitinterface vlan 10ip address 10.112.0.1 255.255.252.0no ip redirectsexitinterface vlan 11ip address 10.112.4.1 255.255.255.0ip helper-address 10.112.1.50ip local-proxy-arpno ip redirectsexitinterface vlan 21ip address 10.116.4.1 255.255.252.0ip helper-address 10.112.1.50ip helper-address 10.112.1.51exitinterface Te1/1/2description 'F2_NTR_4'gvrp enablespanning-tree portfastswitchport mode trunkdot1x port-control force-authorizedexit
  
  ------5548------
  
  vlan databasevlan 10-11,21exit
  
  gvrp enable
  
  ip dhcp relay enable
  
  stack master unit 1!interface vlan 1 ip address dhcp!interface vlan 10 ip address 10.112.0.4 255.255.252.0 ip dhcp relay enable ip proxy-arp
  
  interface gigabitethernet1/0/18 spanning-tree portfast switchport access vlan 21
  
  ip route 0.0.0.0 0.0.0.0 10.112.0.1
  
  interface tengigabitethernet1/0/1 description F2_NTM gvrp enable spanning-tree portfast auto switchport mode trunkSW version 4.1.0.1 (date  05-Apr-2012 time  15:03:04)
  
  Gigabit Ethernet Ports=============================no shutdownspeed 1000duplex fullnegotiationflow-control onmdix autono back-pressurespanning-treespanning-tree mode RSTP
  
  qos basicqos trust coseee enable
  

  SCCM PXE server is fine, tested on Cisco gear.
  

  It's weird, PXE starts working when I hard code the fiber connecting switches to full-duplex, even if they show the full duplex in automatic. Thanks for your help.

• Connection RPS720 redundant external power supply for DELL 5548

  Hello
  We have two DELL 5548 network switches.
  According to the manual of the switch, we can buy the RPS720 external redundant power supply connection to DELL 5548 current to reach the power supply redundant network switches.

  My question is how to connect this external RPS720 of redundant power to the existing DELL going on?

  I only buy the external RPS720 of redundant power, including the power cable connect to switch existing or I need to buy any item to achieve?

  I try to search on the internet but it is altogether less information regarding on this.

  According to the QuickStart guide, all cables are included. Page 4 ftp.dell.com/.../powerconnect-5524_Setup%20Guide2_en-us.pdf

• Stacking question: can I combine a stack of 5548 with a stack of 5524?

  Can I combine a set of four switches PowerConnect 5548 with a stack of two switches PowerConnect 5524? I don't know to ensure they are running the same firmware, but I didn't not see the documentation on the size of maximum stack or between models stacking limits.

  Thank you.

  Yes, you can stack 6 switches together, any 5500 stack with any other, to a maximum of 8

• HDMI piling on PowerConnect 5548

  We have 8 switches PowerConnect 5548 and are interested in using the stacking of HDMI for 10GbE.

  We currently have all 8 switches under tension and production running on them traffic.  Each switch is currently either back 'a home run' to a Cisco switch, or connected to another switch PowerConnect 5548.

  • Is mature enough stacking HDMI technology for a production environment?
  • It would be important if each switch have been 'home run'd ' to the Cisco switch and each 5548 PowerConnect was connected in a loop HDMI?
  • Stacking HDMI technology would require restart us our switches to implement?  A failure would be necessary?
  • All the special items of note regarding the type of HDMI cable?  (i.e. owner or any which best buy HDMI cable work?)

  Thank you
  Jon

  Is HDMI sufficiently stable stacking of the PowerConnect 5548 for production?

  • Yes (100%)
    
  • None (0%)
    
  • A little, but you better pay attention to the comments I post... (0 %)
    

  • Total votes: 5

  Jon,

  Technology HDMI wroks ideal for stacking the PowerConnect 55xx series. You can use the HDMI ports on the 55xx for stacking well and not for uplink to a Cisco or other device.  Also, you can stack only as 55xx switches with other 55xx and running the same version of the firmware.

  On the 55xx, you don't need to reboot the switches, but just plug the cables to create the stack.  An algorithm is used to determine which members becomes master and members who become slaves.  In my view, that the master is determined by which switch has been powered as long.  Don't forget that if you have the switches on different subnets or VLANs, they are configurations will be now changed all switches will become like a big switch.

  The type of HDMI cable is important, you will need to consult the documentation that came with the switch, or you can download the Guide of the user to http://support.dell.com.  You need cables that provide a flow rate of 10.2 Gbps (maximum allowed by the HDMI specification).  Usually the cheapest cables don't provide this.

  -Victor

• 5548, 7048 - PowerConnect backup SNMP configuration

  Hello

  I Powerconnect 5548 and 7480 switches and I would like to know if it is possible to backup with TFTP and SNMP commands configuration files, like I do with my cisco switches?

  Thank you.

  You should be able to use rlcopy which is OID.1.3.6.1.4.1.89.87

  Location of the source Rlcopy.1.3.6.1.4.1.89.87.2.1.3

  Rlcopy the ip address of destination.1.3.6.1.4.1.89.87.2.1.9

  Updates of the firmware also contain the mib files, so you can find the OID http://www.dell.com/support/home/us/en/04/Drivers/DriversDetails?driverId=JRCF6&fileId=3365034200&osCode=NAA&productCode=powerconnect-5524&languageCode=EN&categoryId=NI

• Phone number 5548 LLDP connect

  Hi all and thanks for the responses to come.

  I have 3 power connect 5548 works very well. All of a sudden 5 ip phones just stopped working. They are not able to connect more. I made no change, no change, so I don't understand why it has stopped working. The local network is fine.
  In LLDP neighbors information, I have 35 devices, for most ip phones and only 5 phones not working is not on the same switch number 2.

  The only difference I see is on the "capabilities" of LLDP-MED

  I see that on a phone 'PoE - PD, the inventory of network strategy, capabilities'

  and on a phone not connected "LLDP-MED political network capabilities"

  Phones are ok because if I turn them to a working phone everything is ok again, so the problem is with the switch of dell.

  Perhaps you can help, I can not me to restart it offers...

  I have no green ethernet enabled.

  the stop order #, # no shutdown didn't work :/

  Edit:
  is it possible to see more balls as you can do it with tcpdump?

  Edit:

  Finally restarted the defective switch and it works! at least until now

• Reference DELL 5548 syslog problem

  Hello

  I think 5548 switches syslog bug.

  command "show logging" indicates:

  May 16, 2014 09:25:38: % LINK-w-Up: item in gi1/0/25
  May 16, 2014 09:25:35: % LINK-W-Down: item in gi1/0/25

  Syslog receives:

  May 16 09:25:35 192.168.0.1 LINK Hostname: <192.168.0.7>, article gi1/0/25 #015
  May 16 09:25:38 192.168.0.1 LINK Hostname: <192.168.0.7>, article gi1/0/25 #015

  In syslog can't see when the link was and when backed to :(

  SW version: 4.1.0.16

  Best regards

  Tomas

  Hello

  Handyman work Dell 5548 syslog with rsyslog 5.8.xx linux?

  Best regards

  Tomas

• DELL INSPIRON 5548: PROBLEMS OF DRIVER WEBCAM

  Hello

  I recently bought a 5th generation Dell portable computer 5548 with recognition software preinstalled facial quick access. After a month of using the facial recognition software, it took a license purchase. Because I wasn't ready to continue with the service, the software application has been removed (Uninstalled). Earlier this week, I wanted to make a Skype video call only to find out that my webcam was not working with my Skype. I also discovered that I didn't have any webcam software on my PC. I looked through the available software and drivers for my PC on my drivers and software page but didn't see any software on webcam services there. Please advise on the software suitable for use and a link to the download page.

  Thank you.

  Inés

  Hi Iman,

  Thanks for writing on the Dell Community Forum.

  May I know if you are able to see other devices or devices with yellow/red symbol in the Device Manager?

  Please try to install the chipset driver and the Dell Webcam Central software from the link below:

  Chipset Driver - http://dell.to/1YEJR1g (Please select your Windows operating system from the drop-down)

  Webcam Central software - http://dell.to/1MruR2J

  Also ask you to go through the following link for troubleshooting steps related to the Webcam:

  http://Dell.to/1G6eAsD