6.0 U1b - hosts cannot communicate

Similar Questions

• Host cannot communicate with all other nodes in the cluster virtual SAN allowed

  I get this error after you apply the latest patch:- http://kb.vmware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & externalId = 2135115

  So all the hosts are now review: VMware ESXi, 6.0.0 3380124

  After the reboot, I get the error message on the host cannot communicate with all other nodes in the cluster active virtual san...

  However, the VSAN health check is green, 'get esxcli vsan cluster' shows all 6 members of the cluster ok... and if I reboot a crowd happens ok without the error... so if I reboot another host, it will come without the error... but then the host on which I rebooted before it displayed the error...?  So I can't ever get more than 1 host without the error after a reboot.

  I checked multicast that removes ok, in fact all of the checks in contradiction with the fact that why I get this error...

  Someone at - it ideas? Could this be the latest patch...

  Paul...

  Hello, this has been repeated here: 6.0 U1b - hosts cannot communicate thanks, Zach.

• Error "host cannot communicate with all other nodes in the cluster of enabeld VSAN.

  Hello community,

  We have a problem (?).

  We have a cluster VSAN enabled with four hosts. Everything seems perfect,

  -the configuration is good,

  -Displays the page state VSAN "network status: (green arrow) Normal."

  -Displays the disk management page "status: healthy" for all of our groups of disks.

  -Same 'esxcli vsan cluster get"on each host returns a 'HEALTHY '.

  But we have a yellow exclamation littly on each host 'host cannot communicate with all other nodes in the cluster of enabeld VSAN.

  Anyone with the same problem? Anyone with an idea or a hint?

  Thank you!

  Update vcenter to the latest version and the error disappears. Problem solved! The 'old' version of vcenter performed since September 2014, strange.

  Thank you very much for your help!

• Cannot add host ESXi 5.5 to vCenter for a routed network - cannot communicate with the specified host

  I was wondering if anyone has come across this problem before, who could give advice how to fix them:

  Host of pre-production UCS ESXi migration of a Production vCenter on another network (routing in place)

  Can ping both directions successfully - from vCenter Prod to the host of the pre-production

  no firewall between the two.

  902 port is open on the host

  Host connects to the pre-production vCenter on the subnet even fine

  VCenter production can add different hosts on the same network end

  Even with the various guests of ESXi UCS.

  ESXi host was completely disconnected and removed from vCenter inherited before attempting to add. No dvswitch physical or virtual.

  Then try and add, enter the user name and password and get cannot communicate with the specified host.

  Thank you

  The solution to this. Used ESX host 5.5 3B (3248547) update that disables SSLv3. (Ref: VMware ESXi 5.5 updated Notes version 3B) one of the consequences of this is that older versions of vCenter (such as trying to move the host) can not add/connect host.

  Enable SSLv3 to spend (port 443) on the resolved host (virtuallyPeculiar: connection A ESXi 5.5 U3b host to vCenter with a lower Version A.)

  Note: should not enable SSLv3 to Port 902.

  Ref:

  The SSLv3 Protocol on vSphere 5.x configuration (2139396) | VMware KB

  Many thanks to Suhas Savkoor of virtuallyPeculiar for resolution for this on his website display

• VCloud in virtual machines cannot communicate if they are in another ESX host

  Hi all

  Currently I do a simulation for VCD in my laboratory of the company. I just discovered a few question in this simulation. Hope anyone can advice on that. Thank you.

  Senario:

  1. create an external network with 400 VLANS in vsphere Distribution Switch in two ESX server.

  2. create a VCD organization.

  3 create a pool of network supported by network isolation VLAN 300

  4 create an external organization routed network connection-NAT and select Network (VLAN 400) external and network pool (VCDNI vlan 300)

  5. create two virtual machines and assign the same network of the external organization that was created in step 4.

  6. If two virtual machines on the same host, they can communication or ping to each other.

  7. If two virtual machines in different hosts, they cannot communicate.

  Why step 6 and step 7 will happen? What I have set up wrong? Please advice on this.

  Much appreciated for your help.

  Thank you.

  Concerning

  Ho

  the physical switch must be configured for vlan 400 and 300,

  vcni network tries to encapsulate the traffic on the 300 VLAN, if it is not configured on the physical switch virtual machines will be able to talk if they are on the same host.

  correct its help is not a network back pvlan Isolation needs its own vlan you set to 300, which she in turn can then run 1000 + mac in the mac encapsulated networks in vlan 300,

  Configure the ports on the switch to accept any vlan 300 institutions and it will be sweet

• cannot communicate with primary DNS (68.105.28.11) Server

  I don't have any wireless internet access. When I hit the button diagnosis: "Cannot communicate with primary DNS (68.105.28.11) server." appears

  My IP config:
  Microsoft Windows [Version 6.0.6002]

  Copyright (c) 2006 Microsoft Corporation.  All rights reserved.

  C:\Users\carmen>ipconfig/all

  Windows IP configuration

  Name of the host...: carmen-PC

  Primary Dns suffix...:

  Type of node...: peer-to-peer

  Active... IP routing: No.

  Active... proxy WINS: No.

  ... DNS suffix search list: dc.dc.cox.net

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. : dc.dc.cox.net

  ... Description: Atheros AR5007 802. 11 b / g WiFi adapt

  Physical address.... : 00-1F-E1-79-03-4C

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Address IPv6 local link...: fe80::34b7:70ad:e7c0:14f6% 11 (Preferred)

  IPv4 address...: 192.168.1.116 (Preferred)

  ... Subnet mask: 255.255.255.0.

  Lease obtained...: Sunday, July 17, 2011 10:02:20

  End of the lease...: Monday, July 18, 2011 10:02:20

  ... Default gateway. : 192.168.1.1.

  DHCP server...: 192.168.1.1.

  DHCPv6 IOOKING...: 352329697

  DHCPv6 DUID customer...: 00-01-00-01-0F-E5-04-EE-00-1E-EC-75-99-F2

  DNS servers...: 68.105.28.11

  68.105.29.11

  68.105.28.12

  NetBIOS over TCP/IP...: enabled

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. : dc.dc.cox.net

  Description...: Realtek RTL8139/810 x Family Fast Ethernet

  NIC

  Physical address.... : 00-1E-EC-75-99-F2

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Address IPv6 local link...: fe80::59a7:b3b:4c00:4663% 10 (Preferred)

  IPv4 address...: 192.168.1.119 (Preferred)

  ... Subnet mask: 255.255.255.0.

  Lease obtained...: Saturday, July 16, 2011 13:46:25

  End of the lease...: Monday, July 18, 2011 10:03:15

  ... Default gateway. : fe80::34b7:70ad:e7c0:14f6 10%

  192.168.1.1

  DHCP server...: 192.168.1.1.

  DHCPv6 IOOKING...: 251665208

  DHCPv6 DUID customer...: 00-01-00-01-0F-E5-04-EE-00-1E-EC-75-99-F2

  DNS servers...: 68.105.28.11

  68.105.29.11

  68.105.28.12

  NetBIOS over TCP/IP...: enabled

  Card tunnel Local Area Connection * 7:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Card 6TO4

  Physical address.... : 00-00-00-00-00-00-00-E0

  Active DHCP...
  . : No.
  Autoconfiguration enabled...: Yes
  Card tunnel Local Area Connection * 17:
  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Card 6TO4
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  Card tunnel Local Area Connection * 13:
  State of the media...: Media disconnected
  The connection-specific DNS suffix. : dc.dc.cox.net
  Description...: isatap.dc.dc.cox.net
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  Card tunnel Local Area Connection * 14:
  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  Description...: isatap.residents.gmu.edu
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...
  . : Yes
  Card tunnel Local Area Connection * 15:
  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. NAT - wireless.gmu.edu
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  Card tunnel Local Area Connection * 16:
  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. NAT - wireless.gmu.edu
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  Card tunnel Local Area Connection * 18:
  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 02-00-54-55-4E-01
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  Card tunnel Local Area Connection * 20:
  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Card 6TO4
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  C:\Users\carmen >
  Help, please.  I've been using an Ethernet cable, but it is so EMBARRASSING!

  Hi CarmenZL,

  1. did you last changes made on your computer before the show?

  Follow the following troubleshooting methods:

  Method: 1

  I suggest you to rest TCP/IP and check its operation.

  To reset TCP/IP stack to go to this article and follow the instructions.

  How to reset the Protocol Internet (TCP/IP)

  Method: 2

  Also, follow these steps.

  Step: 1

  a. connect to your router (by typing 192.168.0.1 or 192.168.1.1 in the address bar) and connect. Check your user manual or documentation if you don't know the references of logon.

  b. make sure you are in Setup-> basic configuration category.

  c. scroll down until you see "DHCP Server" - if it is disabled, select 'enable '.

  d. enable DHCP if you want, you can change the number that starts the DHCP IP assigning. (This is optional)

  e. use the DNS servers provided by your ISP. There are many DNS servers out there. It is preferable to use your ISP if possible.

  f. scroll down and click 'Save Settings'.

  Step: 2

  a. click on start and then Control Panel.

  b. go to the networking and sharing Center and then click on change adapter settings.

  c. right-click on connection to the Local network and select Properties.

  d. Select Internet Protocol Version 6, and then click Properties.

  e. Select obtain DNS server automatically an address and press Ok.

  f. Select obtain IP address automatically.

  g. Repeat steps for Internet Protocol version 4 as well.

  Method: 3

  Also perform the following troubleshooting steps.

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers

  On a Windows Vista client computer, you can get an IP address or options from the DHCP server

• Cannot communicate with DNS sever

  Hello

  IM sharing one House with 3 others, we recently had the internet but I can't connect to it while everyone can. When I connect just says local connection, when I diagnose the connection an error message appears saying "cannot communicate with the DNS server. I've never had this problem before and are still able to use also wireless devices and connect to the internet, it just seems to be this router im having a problem with. Ive tried several suggestions found on the internet and none have succeeded, so I was wondering if someone could help me.

  I'm not sure what information you need to know to help so im just stuck it:

  C:\Users\Kayleigh>ipconfig/all

  Windows IP configuration

  Name of the host...: Kayleigh-PC
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :
  ... Description: Intel(r) PRO/Wireless 3945ABG Network Con
  connection
  Physical address.... : 00-19-D2-86-0F-71
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::283b:e88b:bf85:ab79% 10 (Preferred)
  IPv4 address: 192.168.0.2 (Preferred)
  ... Subnet mask: 255.255.255.0.
  Lease obtained...: November 16, 2009 18:09:40
  Expiry of the lease...: November 17, 2009 18:27:23
  ... Default gateway. : 192.168.0.1.
  DHCP server...: 192.168.0.1.
  DHCPv6 IOOKING...: 251664850
  DHCPv6 DUID customer...: 00-01-00-01-0E-7B-45-98-00-A0-D1-6D-87-63

  DNS servers...: 192.168.0.1.
  NetBIOS over TCP/IP...: enabled

  Ethernet connection to the Local network card:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Intel(r) PRO/100 VE Network Connection
  Physical address.... : 00-A0-D1-6D-87-63
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 6:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 02-00-54-55-4E-01
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 7:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {A66451AD - 40 C 4-4DFD-8693-2AB69727F
  E39}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 16:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {5291AF49-A5C9-4154-90AC-597BAF10F
  533}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 14:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Card 6TO4
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 18:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {ECA18F57-EF5B-4DA4-8331-B99497389
  06TH}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 19:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {ECA18F57-EF5B-4DA4-8331-B99497389
  06TH}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 21:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {ECA18F57-EF5B-4DA4-8331-B99497389
  06TH}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 22:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {ECA18F57-EF5B-4DA4-8331-B99497389
  06TH}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 24:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Card 6TO4
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 25:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {ECA18F57-EF5B-4DA4-8331-B99497389
  06TH}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Thank you Kayleigh

  Hi, I just contacted my IPS they helped

• Cannot communicate with primary DNS server

  Here are the results of my ipconfig/all... I had to type this, since I can't access the Internet on my computer...

  Windows IP configuration

  Name of the host... Jeremiah-PC

  Primary Dns suffix...

  Node type... Broadcast

  The active IP routing... NO.

  Active proxy WINS... NO.

  Search list of DNS suffixes... mshome .net

  Wireless network connection Wireless LAN adapter:

  Suffix the connection-specific DNS: wi.rr.com

  Description: Broadcom 4321AG 802.11a/b/g/draft-n Wi - Fi adapter

  Physical address: 00-21-00-35-87-9D

  DHCP enabled: Yes

  Autoconfiguration enabled: Yes

  Link-local IPv6 address: fe80::h496:a7ac:7393:6101% 11 (Preferred)

  IPv4 address: 192.168.0.100 (Preferred)

  Subnet mask: 255.255.255.0

  Lease obtained: Wednesday, June 30, 2010 11:18:20

  End of the lease: Wednesday, June 30, 2010 14:21:35

  Default gateway: 192.168.0.1

  DHCP server: 192.168.0.1

  DHCPv6 IOOKING: 184557824

  DHCPv6: 00-01-00-01-0F-F7-B2-51-00-1E-68-95-9F-3B

  DNS servers: fe80::8cdd:413f:4008:98 c 5% 11

  192.168.0.1

  NetBIOS over TCP/IP: enabled

  Search list suffix the connection-specific DNS: mshome.net

  Ethernet connection to the Local network card:

  State of the media: Media disconnected

  The connection-specific DNS suffix:

  Description: Realtek RTL8168C (P) / 8111C (P) family PCI-ELISE NIC

  Physical address: 00-1E-68-95-9F-3B

  DHCP enabled: Yes

  Autoconfiguration enabled: Yes

  Card tunnel Local Area Connection * 6:

  State of the media: Media disconnected

  The connection-specific DNS suffix:

  Description: isatap. {363BDFFE-FD5C-4926-B273-605FF6EFEE705}

  Physical address: 00-00-00-00-00-00-00-e0

  DHCP enabled: no

  Autoconfiguration enabled: Yes

  Card tunnel Local Area Connection * 7:

  State of the media: Media disconnected

  Suffix the connection-specific DNS: wi.rr.com

  Description: Microsoft ISATAP #2 adapter

  Physical address: 00-00-00-00-00-00-00-E0

  DHCP enabled: no

  Autoconfiguration enabled: Yes

  Card tunnel Local Area Connection * 11:

  State of the media: Media disconnected

  The connection-specific DNS suffix:

  Description: Teredo Tunneling Pseudo-Interface

  Physical address: 02-00-54-55-4e-01

  DHCP enabled: no

  Autoconfiguration enabled: Yes

  You cannot communicate because you do not have a recognized or primary DNS server configuration.  The configuration of the DNS service is incorrect.  It seems that your DNS server is configured to be your router - but it's hard to say.  You actually don't have even one of those enrolled in the internet connection (if it is not to be found in mshone.net).  I don't know what it should be - that depends on your ISP.  Contact your ISP technical support group and help you set up your system correctly - more precisely settings DNS, but the rest as well as you have on the line and do not let up until you made a good connection.

  I'm sorry, we can not help more, but we need their configuration data to set it up properly.

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• AnyConnect Clients cannot communicate with each other

  I have a problem that I've been pulling my hair out... my teleworkers connect to our network of Corp. via a connection AnyConnect VPN (version 3.1) to a Cisco ASA5520. I have not split tunneling enabled for this profile, so that all traffic should pass through the tunnel and all guests are in the same subnet L3... as far as their IP VPN address goes. The problem is the teleworker PCs cannot communicate with each other (pings/RDP/etc.). When I look at the newspaper I see traffic from one to another, have denied anything, but they do not communicate. My Network Corp., I can communicate with the two PCs Anyconnect very well. When I go to monitoring. ASDM itineraries I see each host that is connected to the ASA via Anyconnect, and the gateway for each is the default gateway of the SAA.

  Am I missing some setting in the VPN profile that prevents the access between these hosts? I think that something come in the newspaper...

  Have you enabled crossed and also a free NAT between AnyConnect users?

  permit same-security-traffic intra-interface

  network of the AnyConnect_users object

  subnet

  public static AnyConnect_users AnyConnect_users destination NAT (outside, outside) static source AnyConnect_users AnyConnect_users

  If this does not resolve your problem, please post a sanitized complete configuration of your ASA.

• Guests cannot communicate on newly defined network

  We have an environment to build 381591 VMware ESXi mature 4.1.0 with 8 HP hosts Blade 2 boxes.  We have about 150 guests.

  I added a new network on each host for the vSwitch on which communicate all guests.  It was just a new subnet with a different ID to VLAN.

  At this point, my Server 2008 comments cannot communicate when it is connected to this new network.  My network admin them VLANS are configured on the switches of the enclosure, but I can't check myself again.

  When trying to PING my gateway by default, I get "Destination Host Unreachable".  I checked the IP address, gateway, etc., several times.  The virtual machine can communicate on other networks without problem.

  Any ideas?  The ONLY thing I can think is that it is the first network that I added since the migration from 4.0 and perhaps something is wonky.

  Kind regards

  Justin

  My network admin said that them VLANS are configured on the switches of the speaker...

  If you are not yet able to ping to the gateway address, I would recommend that you have the network admin check the configuration. Maybe the VLANS allowed on the ports are limited! Also, make sure that the subnet mask and the gateway address is correct in the case of a segmented network.

  André

• Disconnected ESXi host cannot reconnect to VCenter

  ESXi 4.0.0 Releasebuild-261974

  VCenter 4.0.0 build 162856

  VSphere 4.0.0 build 162856

  I have a host on the 16 who became disconnected from VCenter recently. I spent some time online means to join new host in VCenter, but each has failed so far. I'm not avoiding perform a reboot of the host due to production VMS are residing thereon. Also, I can't access the Web page for the host, which works very well for the other guests, we have running: https://

  I am able to ping both the IP address and the name of FQDN of the host successfully.

  I did the following things in the hope of resolving, who all have failed:

  1 restart the Management Agents on ESXi host from the windows of the customization of the system.

  2. test the management successfully and rebooted network management network

  3A tried to reconnect to the host via VSphere

  4 registered and the Mode of Support Tech executed the following command: /sbin/services.sh restart when I run this command, I notice that the vmware-aam service does not start.

  Error messages:

  1. (in an attempt restore the link) cannot communicate with the specified host. The host may not be available on the network, may have a network configuration problem, or that the management on this host services may not respond.

  2 (of the newspaper of the Management Agent) panic HttpNfcSvc another process is listning IDE oucederomsurlesecondport 12001; Please ensure that another instantiation of pass run; Cannot initialize the service of httpnfc.

  3. (journal of the VirtualCenter Agent) 0x1499bb90 error 'App' could not discover the ofr is authenticating with host agent version. ; could not resolve version ofr is authenticating with host agent. ; Temporary creation connect spec: localhost:443.

  4. (of the newspaper of the VirtualCenter Agent) 0x1499bb90 error 'App' SSLStreamImp::BIORead (0x2e408bb0) has expired; SSL connection failed with error BIO

  [5 (journal of the VirtualCenter Agent) HttpUtil::ExecuteRequest] error in sending request - SSL Exception: transfer the SSL expired local: 127.0.01:63355 peer: 127.0.0.1:443

  Any suggestions would be greatly appreciated! Let me know if you need to work as well with more information.

  Thank you!

  BOE

  It is an ugly one. At least a restart if not re-install. To minimize downtime, you can close out of virtual machines to the inventory and put them on another host/cluster.

  ___________________

  A +, EASD, MCP, MCSA, MCSE, MCTS, MCITP, MCDBA, NCDA, VCP4

  If you find this or any other answer useful please consider giving points by checking the correct or helpful answer.

• Tecra P11 cannot communicate with scanner

  6 months ago, I replaced my old Tecra A3 with a P11. For almost all of this time, it was a lottery if the P11 would communicate with the scanner function (fine print) of my Canon MP170 printer/scanner. The only reliable method that I had was back system restore at the date of purchase--> do the scanning-> undo system restore. What a pain!

  This printer was showing it's age so I bought a new Epson. Same problem, the computer can talk with her to print but cannot communicate to scan. I changed the USB cables and ports, made what Epson has suggested, but to no avail. Tips last Epson a me summer "it must be a computer problem.

  Anyone else had a similar experience? More important still, you haven't solved the problem? I have no desire to return to the merrygoround of system restore.

  Hello

  It is really strange, and the whole is illogical for me.
  How it can work with the settings but not later? What happens during this time?

  Last month I bought the large HP device with printing, scanning and the adjustment function. I use it with my Tecra A11. The entire configuration was completed in 10 minutes. I ve tested with USB cable and also with wireless LAN functionality. No problem at all.

  In my opinion the most important is the pre-installed software that you get from the manufacturer.
  If Epson believe it must be computer you asked what that would be. I mean they should have sufficient experience with own products and they have tested the software they offer.

  Unfortunately I can't help you with this, but I will follow this thread to see what the problem was.

  If you will be able to find a solution please let us know.
  Good luck.

• FP2000 state witness remains on red cannot communicate

  I just tried to update the software on a ps2000 not the indicator light remains reading and cannot communicate. any ideas.

  I have reset with in safe mode and reset the switch dip on a moment, I communiate with her. I tried yesterday with no luck, but today it worked I think I should get going now.

  Thank you

  Tim

• computer cannot communicate with over 8600

  My 8600 Officejet Plus works fine on a wireless network for about a year, but after restarting the computer yesterday morning, I get the message "...". cannot communicate with the printer.  I tried all the suggestions below without result.  I can access page ews from the printer to the computer and I get my apps on the internet every night. I have Ran the network to the printer and all past test.  The Network Setup page shows the printer is connected and ready for the correct ip address.  I ran the HP print and scan doctor and you can see that everything works.  I also ran the troubleshooter in Windows and it showed no problem with 'the printer is ready.  I unplugged the router, printer and restarted Windows.  I removed the printer via the "devices and printers" window, as well as the HP software.  I reinstalled the software, connected the printer and run the wireless configuration.  I've updated the ip address on windows.  All to nothing does not.  Any help would be appreciated.

  Running Windows 7 Home Premium

  Belkin N router is

  In fact, I found the problem.  It seems to run a malicious program to the startup disable Norton anti-virus and changed several keys in the registry that prohibits the computer to communicate as well as Outlook unauthorized access to my POP3 account and who knows what.  I managed to uninstall Norton, then re - install a newer version.  This enabled Norton run a quick scan before restarting.  After re-booting, Norton has been disabled again.  I used Norton Erase to analyze and repair the registry that solved the problem.  Immediately after re-boot after the last scan and fix the network Windows Test Page that announces the printer has been installed on persistent organic pollutants.

  Thanks for you quick response, however.  I suspect a virus when I tried, without success, to open Norton in order to disable the firewall and couldn't.

• SE error message saying the printer cannot communicate with the computer cause of blocked files.

  Original title: DRIVER of PRINTER BLOCKED

  A COMMS. ERROR MESSAGE ME SAYING THAT MY PRINTER CANNOT COMMUNICATE WITH MY PC. AFTER COMPLETING THE USUAL HARDWARE CHECKS THAT I USED THE SERVICE CENTER OF DELL ONLINE THAT REMOVAL OF TWO STATES ' DLEACOMS. EXE' AND ' DLEAWBGW. EXE ' MUST BE RELEASED TO ALLOW MY PRINTER TO WORK.

  I SEE NO REFERENCE TO THESE FILES IN THE WINDOWS FIREWALL AND TO THIS DAY THE ONLY WAY AROUND THIS PROBLEM IS TO REMOVE THE PRINTER AND REINSTALL, BUT IT WORKS FOR A SHORT PERIOD. I USED (BY REMOTE CONTROL) THE STATION OF SOLUTION DELL THREE TIMES BUT EVEN THEY EVENTUALLY REMOVE ALL AND REINSTALL THE PRINTER.

  SOMEONE HAS AN IDEA HOW THESE FILES CAN BE UNLOCKED?

  I suggest to disable CAPS LOCK key since your message is all in the capital and difficult to read. Have you tried to add to the exception in the Windows Firewall? Try also to change your network connection for work or at home instead of public. Also make sure you installed the latest version of the driver and are compatible. Also try to run the tool:

  http://support.Microsoft.com/mats/printing_problems/

  If the problem is not resolved, contact Dell customer service.