6746c Pavilion: my Hp Pavilion will not start

Similar Questions

• HP Pavilion will not start? help please.

  A few weeks ago, I had a pavilion dv6700 out of my brother, when I turn it on hp invent comes on the screen and shortly after it turns off then try to start over, he repeats this process again and again, sometimes after that it says "not found opperating system".

  Ive tried a system restore and also led a diagnosis whose results were, for the primary hard drive no self-test "no IDE device".

  and 'transmitted result' memory test any help would be great thanks in advance.

  http://h10032.www1.HP.com/CTG/manual/c01295877.PDF

  {+} Removeal and replacement procedures

  [+] component replacement procedures

  Click on HARD drive

• HP Pavilion will not start

  I have a Pavilion P6774Y desktop computer.  A few days ago, he would not wake up.  I turn it off and be restarted using the power switch and the blue HP screen appeared, followed by a black screen with a cursor blinking in the upper left corner who disappered after a few seconds.   After repeating this a couple of times, I swapped the monitors and HRT has not set.  Then I unplugged it, let it sit for a few minutes, plugeed it it and restarted and it started normally.    Since then, the same question has occurred several times.   Sometimes it reboots normally, other times, I get the black screen.  Sometimes it takes to unplug and reboot several times for it to start.  Does anyone have any suggestions where to look for a solution?

  TF1965, welcome to the forum.

  There are two possibilities: 1) a lack of power supply unit (PSU) or 2) a hard drive failed.

  Here's a guide to troubleshooting of the PSU.  You can test the hard drive by using the Test SMART in BIOS.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• HP Pavilion will not start past blue hp invent screen

  My computer does not boot past the blue hp
  Invent the screen. I took the sides off the computer. I started and I realized what was the noise that I heard and whence he came. It's the hard drive makes a noise like a fan starting then a rattling noise. Then it stop trying to load and is repeated several times, then closes. I unplugged the power supply for the drive hard drive now it
  take care when I unplug it but I can't do anything without hard drive.

  Your hard drive has failed. If you are still in warranty, contact HP to send a new hard drive. If you are out of warranty, it will be much cheaper to buy a retail hard drive to replace the original. Hope you have a value recovery disk?

• HP Pavilion will not start the power upward

  I have a HP Pavilion (prod. # GG753AV #ABA) running under Windows 7.

  Power on, the switch lights up blue, fans are taking place but not boot upward and no display

  I tried unpluggin keyboard etc but no luck

  Thanks for any help

  Thanks for getting back to me!

  Make sure that the monitor is on the correct input/source. On the monitor, you should have a Menu button or a button input/Source. The Source of entry/must be set to VGA. If the monitor is set to a different port like DVI or HDMI type, it might be initially to go to sleep because it does not detect plugged into ports. Check and double check the input source.

  Also try reinstalling the RAM, which is just out the RAM and put it back in. If you have 2 sticks of RAM, you can also try to just put one in at a time in each slot to see if the screen lights up.

  I hope this helps. Let me know what you get results.

• HP Pavilion will not start, has horizontal lines on monitor - HP Pavilion Elite M9280a

  I tried to start my computer yesterday and I had a brief message 'Error in Vista' then - my computer would not respond.

  The monitor has just shown the colored horizonal lines.  Then, I rebooted the computer.

  Since then, I can't reboot my computer at all however, I can get into safe mode to connect but remain - lines horizinal who won't go away.  The icons are much larger in safe mode too.

  When I try to log in normally, the system will repair mode and finally displays the following message:

  ' Start can't fix computer automatically "I went to see the details of the problem and this will display:

  Signature of the problem

  The Startup Repair V2 problem event name

  Problem signature 01 Auto failover

  02 6.6.6000.16396.6.0.5001.18000

  6 03

  04 131074

  05 no cause root

  06 no cause root

  07 0

  2 08

  WRP 09 repair

  2 of 10

  6.06.000.0.00.256.1 OS version

  Locale 1033 ID

  I did start diagnostic tests and everything seems ok, but the computer doesn't not recogise my graphics video card.  The system, it shows the video card - VGA video controller - PCI Bus 2 - device 0, function 0.

  Can someone help me please!  Products listed below

  http://h20565.www2.HP.com/portal/site/hpsc/template.page/public/KB/docDisplay?javax.portlet.begCache...

  Hello

  Technical page in your PC Watch: the Nvidia GeForce 8600 GT, or integrated graphics. You can check which graphic solution you have?

  You can see the desktop when it is in safe mode?

  Try the safe mode with networking enabled.

  A position that interests you, your Version of the OS (6.06.000.0.00.256.1) indicates you are running the original version of Vista. You must also upgrade Vista to Service Pack 2 (6.0.6002).

  If you can not download the drivers in safe mode with network, can you download the driver on another PC and save to disk?

  While in safe mode try to remove the possible corrupt driver using Control Panel, restart and see if Vista will load a generic graphics driver. Then, you should be able to download and install the appropriate driver.

  Jaco

• HP Pavilion will not start. Password Startup requirements.

  I have a ho27c model 23 H P Pavilion all-in-one number.  After an altercation with a crook of phishing, I can't get starts the request a password at startup.  After several tries, I get nothing, but demand repeated password.  I never opened a session as an administrator and has never seen it before.  Can anyone help?

  Product number is: F3D92AA #ABA and the model is: 23 h 027 c

  Thank you...

  ... LWMc

  It is always helpful if you specify the operating system installed.

  You have two options.

  Download a stand-alone antivirus\malware\adware scanner of a real antivirus company.

  Search for your game of recovery disks and perform a factory image recovery.  You can also do this from the power on with a F11 key. You is probably the best option.

  Once you got make sure that your PC and install a highly rated internet protection suite. Freebie antivirus programs are no help when it comes to rogue virus and malware such as you seem to have picked up. I prefer ESET Smart Suite and Norton Internet protection.

• Pavilion ID46 g6 will not start

  Product: Pavillion g6 ID46

  [Edited by Moderator] Serial No.

  Product # A6Z74UA #ABA

  OP sys: Windows 7 Home Prem OA

  Pavillion G6 my husband will not start. What happened: returned to the computer after being away for a while, shook the wake up the mouse and the screen «has exploded in many colors and motion pixels» Screen went black, then a screen "do you want to start in safe mode" popped up. He tried a start-up without danger, but he failed and gave him a Bios Application error 501. He tried to restart the computer, but it crashes on the 'Starting Windows' screen with 4 color icon.

  I have:

  Removed the battery and tried to restart. Not good.

  Has taken the hard disk and and reinstalled it. Ditto.

  Tried to boot mode safe, before and after the following below. "Loading files" still stuck on Windows\System32\drivers\CLASSPNP. SYS

  Burned and ran a repair disc. Took 4 hours and the program ran at the end when I was asked to reboot. Computer hooked on "Starting Windows" screen. (I left this screen function for more than 5 hours without this change.)

  Ran the program System Repair twice, same results.

  Start of Tests ran. After self-test of the main hard drive, hard drive SMART and verification Test of memory system (passed 100%)

  Tried to restore the BIOS using Windows + B and power with several attempts. Button Power LED stays on, about 20 seconds later a small LED on the "caps lock" key flashes white twice. Black screen and nothing happens after 5 minutes. He raised his eyes and 2 flashes is supposed to be the corruption of the BIOS.

  Error log lists these: quick 03F0 303, 501 error and error of hard disk 1.

  I have a lot of intelligence of the computer, so appreciate any help you can give, especially if assistance is simple and easy to follow terms.

  Mahalo in advance!

  Well, nothing worked and I did not attempt to remove the HD and turn it on again. Husband returned to a comp sci student who managed to get some info on the HD, but said that the HD was shot.

  Good thing is that I got a new Asus laptop and put my old computer to my dear husband. So, I guess that the problem is solved!  Thanks for your help.

• Pavilion a6327uk will not start. Light output at the rear is enabled, all the work of 3 fans, but does not start.

  I have a Pavillion equipped a6327uk for vista 32 bit. I had similar problems before and remove all cables, hold the button to boot without the power connected, reconnect the and then turn on solves the problem. I suffered a blue screen, where I was told the computer was stop and spills of memory. Then I rebooted the computer froze and since then it will not start. I led on the power supply/process button cable about 30 times more than three days without success. The computer does not go to the HP logo screen, it just stops. Can anyone help with further action please.

  It could be almost anything that prevents your computer from starting to start to eliminate things.  If the computer under warranty?  If this is not the case, unplug everything including the power cord from your computer. Unplug the keyboard, monitor, mouse, readers flash and all other connected outside of the machine. Open the unit and unplug all the devices connected to the power supply except the motherboard.  Disconnect the hard drive cable and power supply data connection, disconnect the connection cable and power supply of the CD/DVD data, disconnect any drive card reader or floppy drive.  Therefore remains connected to the power supply should be taking 20/24 pin to the motherboard and 4 or 8 pin 12V for the cpu power cable.  Remove all cards that may be in the slots, as the video card, modem, network card (if they are not built in to edge of devices.) Just the cards that can be inserted into the slots.  Make sure all items are away from the computer and cannot cause a short circuit when you use power. Look at the motherboard and see if the capacitors were bulged or rounded top and maybe even a brown substance leaking from the top.  Check the video card as well for the same and a blocked fan who may have been not turn.  Test the power supply with a volt/ohm meter if you have one. If this is not the case, turn on the power and see if the fans are running and you get beeps.  If this isn't the case, hold the power button for about 5 seconds until the machine turns off.  Try only a chunk of memory at a time and in each of the slots.  If it starts to act normally, it is probably food.  If the sounds seem normal, unplug the power cable and install one at a time from the video card and connect the monitor to it. Plug the power cable from back in and start the machine.  If you have a video, keep disconnect power, adding another device such as the keyboard and the mouse until you arrive finally to your hard drive.  Do your last hard drive because there all your important data on it and you do not want to expose to all this test.

• Laptop will not start without the battery attached

  Hello

  I have a Hp pavilion dv6700 series (dv6840el) and just, it will not start without the battery attached.

  If I plug in the AC adapter, I get some computer activity (fan, noise of the dvd player and HD drive spins) for about 5 seconds, then shuts down.

  Once I plug the battery (which is dying, who need a replacement), the laptop starts fine.

  So my question is: what is a motherboard or a problem with the AC adapter?

  The AC adapter looks ok, however. But if I am considering buying a spare battery, I assure you that I have a new adapter as well.

  Thanks in advance.

  Hello

  Visit this link

  http://h10025.www1.HP.com/ewfrf/WC/documentSubCategory?tmp_rule=61317&tmp_task=solveCategory&CC=US&DLC=en&lang=en&LC=en&Product=5081068&Query=dv7-6052ea&Tool=

  Good Luk

• I can't download Windows updates or updates of Windows Defender, and my BITS will not start.

  Hi, I have a HP Pavilion dv4 Notebook PC, and I can't get my updates of windows to download anything. My BITS will not start.

  -Processor: Intel (r) Core (TM) 2 Duo CPU
  At 2.10 GHz, 2.10 GHz T6500
  -Memory (RAM): 4.00 GB
  -System type: 64-bit operating system
  -Windows Vista Home Premium Edition
  -Service Pack 2

  I have Webroot AntiVirus with Spy Sweeper and I recently downloaded the Malewarebytes Malware Anti.

  Whenever I try to download an update for anything, be it Itunes, Windows Defender, Windows updates, updates to HP or Microsoft Updates, they do not always arrive.

  When I go into the service menu & try to start BITS it comes up with this message:

  Windows cannot start the Service on the Local computer's Background Intelligent Transfer
  Error 126: The specified module is not found.

  When the updates of Windows fails to download updates, it comes up with the error Code: 80246008.

  I tried to download on microsoft.com BITS Repair tool, but it is said that the tool is not necessary.

  I really need someone to help me and to understand this point for me, it's happened now for about 3 months. When I bought the laptop I had Webroot AntiVirus with Spy Sweeper installed, and I just installed Malwarebytes' Anti Malware, a week ago.

  Anyway, do the following:

  1. download the Norton Removal Tool, save it to your desktop: ftp://ftp.symantec.com/public/english_us_canada/removal_tools/Norton_Removal_Tool.exe

  1B. download the tool McAfee Consumer Product Removal, save it to your desktop: http://download.mcafee.com/products/licensed/cust_support_patches/MCPR.exe

  2. close all open applications (that is, anything with an icon on the taskbar).

  3. click right on the file saved in # 1 above, and then select run as administrator to run the utility. DO TAP not your keyboard until the race ends, then restart.

  4. click right on the file saved in # 1 b above, and then select run as administrator to run the utility. DO TAP not your keyboard until the race ends, then reboot again.

  5 test.

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Somewhere, I messed up my permissions, turn off the computer to see if it helped, now will not start at all. The start bar stops a quarter turn along. I tried in SafeMode as well do. I ' on a Yosemite iMac running.

  Somewhere, I messed up my permissions, turn off the computer to see if it helped, now will not start at all. The start bar stops a quarter turn along. I tried in SafeMode as well do. I ' on a Yosemite iMac running. I can't enter to give more details. Can anyone help? There are a load of work due to deliver to the printing press Monday

  Have you tried to boot from the Partition Recovery and repair then the disc from there, using disk utility?

• G5 will not start. LED light on. Fans before working.

  Early 2005 G5. running 10.5.8.

  G5 will not start. LED light (no flashes not but solid). Fans before working. Rear fans blowing not. Cleaned up the dust. A exploded during a down and will not restart. Any thoughts? Is that a bad diet? What I would do. Thanks for any help. I love this old computer and hope to keep fixed and working.

  Sam

  Some of the fundamental things include the pram/clock battery replacement

  since they may be dead; then with a power failure, sometimes the Mac

  do not restart. Usual power management unit & reset NVRAM/PRAM are

  methods that sometimes also used as a troubleshooting measure.

  • Reset the Mac chip power management: (see SMU)

  http://www.thexlab.com/FAQs/resetpmchip.html

  • How to reset NVRAM-LANDAU on your Mac - Apple Support

  A hard reset can sometimes be used, where the power is disconnected

  the logic board and power removed from grill; Then push the Start button / stop.

  (But maybe not. Several PowerMac computers, I had, some people found this helpful)

  You may also remove and reposition cards and other items

  the inside of the case, to be sure they are connected properly. Be sure to not

  In short anything, due to the static load or residual power in the circuits.

  The hour is late here, so I'm not going offline; If all goes well a battery original or novel, etc.

  can help to put it on again. Also sometimes the power supply has some faulty fans,

  circuits or capacitors, so they can be troublesome to repair or replace.

  Good luck in this case!

• Firefox will not start after update

  Firefox will not start today. I think he had an update yesterday.
  Click it, lift the loading symbol, but never implemented. In Task Manager it is a firefox.exe * 32 running. Have you tried to uninstall, delete Mozilla Firefox folder in Program Files x 86 iti also tried to suppress the appdata profile (after saving the Favorites and passwords). I can't even boot up in firefox safe mode and can not get to start Profile Manager. If I start (7 x 64) of windows in safe mode, I can start firefox. I use Norton Internet Security. I checked the settings of firewall smart and experienced of firefox is still set to allow. I tried starting firefox with smart firewall turned off and firefox still refuses to start
  Renounce top almost ready

  Hello ziggy1, as this can sometimes be caused by a malware active on a system, please run a scan with tools of different security like the free version of malwarebytes, the adwcleaner and the scan to microsoft security.

  Fix Firefox problems caused by malicious software

• Carillon of boot loop - start 2011 MBP will not start.

  I have a start 2011 15 "MBPro8, 2

  Quad Core Intel Core i7

  2.30 GHz

  Boot ROM version: MBP81.88Z.0047.B2A.1506082204

  Intel HD Graphics 3000 VRAM:512 MB

  AMD Radeon HD 6750M VRAM:1 GB

  8 GB of RAM 1333 MHz DIMM0

  It will not start.  Trying to start the machine, it enters a loop-

  1. startup chime

  2. grey screen with Apple

  3. the small wheel starts to turn under the Apple

  4. the screen goes black

  ... and the cycle starts over.

  The computer does not start in Mode safe.  In an attempt to safe mode the loop above has the addition:

  3. a progress bar is displayed but does not progress.

  I have reset the PRAM

  It will start up in target Mode, so I was able to recover data

  In target Mode, I was able to run first aid utility on the drive.  This has not fixed the problem.

  I can hold down the Option key and see Macintosh HD and the recovery Partition.  If I try to boot from the recovery partition, I get the same loop.

  I can start in the Test of online material, which revealed no material problems

  I can boot in Verbose mode and it always happens in the same place

  Execution fsck_hfs (version 226.1.1 of hfs)

  BootCacheControl: cannot open /var/db/BootCache.playlist: 2 no such file or directory

  ' ' It would be possible for me to insert the "var/db/BootCache.playlist" file using target disk mode?

  Other thoughts?

  Check Google for this error, it seems to be common.

  Apparently the startup configuration file is corrupted. These 2 articles can be useful:

  http://www.Hackintosh.computer/?p=67

  https://www.iFixit.com/answers/view/192201/unable+to+open+-var-db-BootCache.play list % 3A + 2