A surefire way to access to the part of my PHOTOS of the iphone, the Web, Safari?-on icloud backup

Similar Questions

• Problems with access to the web pages, email, video, etc. even when I have 4-5 bars.

  I installed a Dell Wireless 1505 low-profile carrier 1.2 antenna dim/insp in desktop. Its a PCIe wireless lan card. But since last Tuesday patches have been installed I had problems with access to the web pages, email, video, etc., even when I have 4-5 bars.  Someone at - it an idea of what's going on.

  Hi William e. Swann

  1. what web browser do you use?

  Method 1:

  You can read the following article and check.

  You may experience connectivity problems or performance issues when you connect a portable computer that is running Windows Vista or Windows 7 to a wireless access point

  Method 2:

  You can also read the following article.

  How to troubleshoot network connectivity problems in Internet Explorer

  Hope this information is useful.

• N3048 access to the Web Interface without OOB

  I recently had our switch replaced by RMA and have access to the web interface via oob. I'm not sure how to access ports and other subnets and want to access the web interface of the server room outside. It's probably something very obvious, but I don't have the original switch to check the configuration. Any help would be appreciated. Thank you.

  You can use in-band or oob access to administration from inside or outside the server room.  The port of oob is a completely separate network used for management only, but you can also use a port in the Strip management.  By default, VLAN 1 is usually used in the Strip to transport of management traffic.  If you set an IP address on VLAN 1 you should also be able to manage from this IP address.  Measures would be to define the IP address on VLAN 1, ping ping to test connectivity, remote and then use your browser to connect to the web INTERFACE.  You should be able to use the same username/password that was used for the oob port.  Without a set of name of user and password, the web INTERFACE will not allow the session.

  B

• Adobe flash player 11.0 blocks access to the Web site home pages

  Why is Adobe flash player 11.0, allowed to block access to the Web site home pages, until their trash is installed?  They should be prosecuted for punishment of the loss of time by Internet users, who spend countless hours trying to fix their garbage, which takes control of the web and blocks PCs access to their program settings, unless it is done according to their specific updates. N ' ILS OWN INTERNET and everything on it, or what?

  Are you sure he blocked it, or the web page requires Flash Player to see this?

  Most web pages require an element of Adobe Flash Player.

  First of all, try to enable Active Scripting in the areas of Sites Internet Options, security settings, trust.

  You should also add a corrupted on.

  Click Start, type: Internet Options

  Press enter

  Select the "Advanced" tab

  Under reset Internet Explorer settings, click "reset".

  This should restore the Internet Explorer default settings.

  Then reinstall Flash Player

  http://get.Adobe.com/flashplayer/

  ----------

  Flash Player

  Troubleshoot installation of Flash Player for Windows

  http://kb2.Adobe.com/CPS/191/tn_19166.html

  Troubleshooting player stability and performance

  http://blogs.Adobe.com/JD/2010/02/troubleshooting_player_stabili.html

  Uninstaller

  http://kb2.Adobe.com/CPS/141/tn_14157.html

  Flash Player Support Forum

  http://forums.Adobe.com/community/webplayers/flash_player

• The accessibility of the Web APEX is consistent?

  I am referring to the Web Content Guidelines of the accessory (http://www.w3.org/TR/WCAG20/).
  
  For most of the projects of governance, the requirement is that any application is supported - the accessibility of the web. This means, it doesn't have to be unencumbered, but that of alternatives not indicated if any user has some disadvantage (disability or some options turned off, etc.) and cannot use a special function.
  
  I would like to know if anyone has experience with the type of action must be taken to ensure that an ApEX application is «supported web accessibility» Y at - there no official statement on this subject and the Apex Oracle?
  
  I have my doubts about the use of
  * Icons = > may depend on the theme, but is always a text alternative for the included icons?
  * JavaScript = > APEX Will still work if JavaScript is disabled?
  * Cookies = > I think apex may work with sessions of the url instead of using cookies. Has anyone ever tried?
  * ...?
  
  _ applications based on the overview of the requirements of the W3C for browser
  
  Noticeable
  
  -Provide non-text content text alternatives.
  -Provide captions and alternatives for audio and video content.
  -Make content adaptable; and make it available to assistive technologies.
  
  -Use sufficient contrast to make things easy to see and hear.
  
  Operable
  
  -Make all the keyboard of accessible features.
  -Give users enough time to read and use content.
  -Do not use the content, causing convulsions.
  -Help users navigate and find content.
  
  Understandable
  
  -Make the text readable and understandable.
  -Make content appear and operate predictably.
  -Help users avoid and correct mistakes.
  
  Robust
  -Maximize compatibility with current and future technologies.
  
  Published by: W. Sven on September 11, 2009 11:54

  Sven,

  I did some 508 complaint with APEX development in the past, and it is really very easy.

  The mechanism of the apex model makes it easy to make your 508 compliant applications. The only thing to keep in mind when creating applications is that less is more; You may need are reluctant to use jQuery or other frameworks based on JavaScript, because they usually give screen readers a moment difficult.

  The directives that you posted are a good start. There are also a lot of information available online, more precisely at http://www.section508.gov/

  Another thing - we were able to get a couple of disclaimers with some of the more complex pages that we have built, as they were not for all users, but only for a select few users admin.

  I hope this helps!

  -Scott-

  http://spendolini.blogspot.com
  http://sumnertech.com

• Apple a day will include Messages in the web interface for iCloud?

  Hello world

  That I really like to write my text Messages on my iMac and MacBook Pro, I was wondering if, one day, we will be able to send text messages from the web interface for iCloud.

  I mean, the 'Messages' application might appear with all the others.

  

  During my short time with an Android phone, I used text powerful app. I had to associate the application phone on a Google account and connect to the web interface powerful text with the same Google account.

  It was pretty cool and useful.

  So, I'm thinking the solution to include 'Messages' to iCloud so that non-iMac users could write SMS with their keyboard too.

  THX.

  This is a user to user community, Apple will not read your comments, if you have any suggestions that you think might improve iCloud, you can send Apple your your comments here.

• Other ways to access to the control center

  I'm a quadriplegic and can't touch to the iPad, but I use the switch access. That leaves several things that I can't because you have to do some kind of shot or another action.

  I was trying to find another way to bring up the control center, since I can't slide with my finger. I actually found a several months ago and put in a recipe under switches, but something went past and disappeared and I don't remember what I did. Any ideas?

  Also, I need to be able to implement all applications running in the background that must be killed. I can't double click on the home button. It any suggestions?

  I use the command with 2 switches. If that helps anything.

  Thank you! -Doug

  Hello WDMaples,

  Thank you for reaching out to the Community Support from Apple. I know how it is important to be able to access all the features of your iPad, and I have an article that should help you to implement the control you are looking for with your switch access. This article should help guide you through setting up the recipe to replicate hitting swipe and double click on the home button.

  Switch control: Basic Techniques

  If you experience any problems or have any questions, please let us know. The entire community is here to help.

  -Best regards-

• Re-uploaded because there was no access to the web, and it is not yet. Opens in private browsing, no Firefox tab is visible, so I can't do anything.

  I don't remember having chosen Private Browsing until I deleted Firefox on my computer. After you download from the Web site, the same screen appears. It does not resemble the Web site displays. I have a screenshot, but don't see a way to fix it here.
  The top line is blue background of Windows and said "Start Mozilla Firefox - Mozilla Firefox (private browsing) Page".
  Lower than that of the context Tan the usual File, Edit, View etc.
  Lower than a tab with: the image of Fox and the "Mozilla Firefox Start Page.
  Thaat below: arrow, arrow, box "go to a Web site", and arrears on the right a blue g and a tab drop down to search engines, down for downloads and the symbol of the House.
  bottom line usual Google that shows that my most used bookmarks
  The large area below that contains the symbol of the Fox in the Center above the search box (which does not). In the upper right corner is "mozilla" gray type.
  Crossing the lower part is a clear grey banner with "downloads, Favorites, history, modules, sync and Settings" with their symbols above.
  I had to remove PC Matic Supershield to get the download to work at all, and now after hours of tests, I am right where I started.

  Make sure that you are not Firefox running in (permanent) private browsing mode.

  • https://support.Mozilla.org/KB/private+browsing
  • Tools > Options > privacy > Firefox will be: "use the custom settings for history".
  • Uncheck the box: [] "always use the navigation mode private.

  You can check for problems with preferences and try to rename or delete the file prefs.js and possible prefs - numbered # .js and a user.js file possible to restore the values all default prefs.

  • http://KB.mozillazine.org/Preferences_not_saved
  • http://KB.mozillazine.org/Resetting_preferences

  Try to start the computer in safe mode Windows with network support (on the startup screen, press F8) as a test to see if that helps.

  One possible cause is security software (firewall, antivirus) that prevents or limits Firefox or plugin-container process without informing you, possibly after the detection of changes (update) for the Firefox program.

  Delete all rules for Firefox and the plugin-container in the permissions list in the firewall and leave your firewall again ask permission to get full unlimited access to the internet for Firefox and the plugin-container and the update process.

  See:

  • https://support.Mozilla.org/KB/server+not+found
  • https://support.Mozilla.org/KB/firewalls

• MacAfee blocked access to the web in Firefox?

  I use Firefox as my default browser and McAfee Security. Today, a popup asking if I would allow Firefox to access the internet and I accidentally pressed on 'no '. I had to use Chrome to reach this site because Firefox does not connect what anyone on the internet. How to solve this problem? My email is [email protected]

  My e-mail is [email protected]
  See updated McAfee Security Center and firewall settings to allow access to the Internet, Firefox

  Email or reply to this message if you need help

• WVC210 DYDNS AND PROBLEMS WITH ACCESS TO THE WEB

  I have 2 Configuration for WVC210 cameras on dydns of deleted I can't see them on the web. I can access via the local network using the ip address and port or the dyndns name and port. The router has listed as a virtual server and I even put one of them is like DNZ (outside the firewall of the router), the port check tools show a port opened from a remote location. And I can ping. But I can't connect to the camera. Also, I was able to view a WVC54GCA camera with the same configuration. Any ideas?

  I can get both of these cameras no problem... just not able to connect but the login box comes right to the top as soon as I hit him enter after you put the URL...

• Dell Powerconnect 3548P - a reference not rattling, or allowing access to the web console

  Hello

  I wonder why we are able to access our PoE switch through the web console http, I can connect via the serial port and the Dell Setup Wizard, we have all the information and our ip address for that switch to 10.0.3.192 255.255.255.0 with a default gateway of 10.0.3.1.

  So if trying to ping so still times out, and if you connect to it and change the pc ipv4 parameter to point to him, he will not allow access via browser.

  Any suggestion or help would be greatly appreciated, thank you.

  I've reconfigured everything ManageEngine OpUtils connection to stack Dell via SNMP v2c and the issue seems to be fixed: stack of Dell was to be online from 4 pm and noting happened during the many analyses of OpUtils SNMP. I think that the problem is resolved.

  For your convenience, Dell battery of newspapers (RAM and file those with the maximum detail level) show not record SNMP loss or drop.

  Thanks for your suggestions.

  Marco Dodi

• 200 series smart switch (SG200-18) access to the web interface

  Hi all!
  The system flashes green which I understand means that it is currently using the default IP 192.1681.254.

  1. do I need to connect a computer directly into it to get on the Web site? Or do I just use any computer on the local network that uses an IP address from that subnet 192.168.1.x?   The subnet in this branch is etre.1.x in any case.

  2. these instructions in order to use a computer on the same subnet - what is State only when it is in its configuration by default or always? i.e. I'll only ever be able to reach these switches from a computer within the respective branch?  Or, for example, may switch to the branch 1 (sous-reseau.1.x), be configured to allow access to a computer at the head office (sous-reseau.0.x) or via the VPN (sous-reseau.254.x)? How?

  3. how to respond to pings?

  Hi shead, if you connect this switch in a network with DHCP, the device will get a DHCP address for the IP address of management.

  To be able to get web access to a different subnet, you must set the default gateway of the switch of the device, which will happen the router, the sx200 will not forward anything.

  The switch responds to ping by default then there is another problem.

  -Tom
  Please mark replied messages useful

• IPSEC RA - activate crossed but restrict access to the web

  ASA5520 8.2 (5) 30

  Greetings,

  I have an IPSEC RA strategy that has implemented to tunnel all traffic (no split tunnel) by the ASA (which ends on the external interface).  I need to be able to allow VPN users to access a web page (crossed) thesesame on the external interface.

  ++++++++++++++++++++++++++++++

  Here are the current settings:

  Group Policy Admins L internal

  attributes of Group Policy L_Admins

  value of server WINS 172.16.0.33 172.16.0.9

  value of 172.16.0.33 DNS server 172.16.0.9

  VPN-idle-timeout 60

  VPN-session-timeout 480

  VPN-value filter-admin-l

  IP 172.30.4.0 allow Access-list l-admin-test-filter extended 255.255.255.252 host 172.16.0.33

  IP 172.30.4.0 allow Access-list l-admin-test-filter extended 255.255.255.252 host 172.16.0.9

  IP 172.30.4.0 allow Access-list l-admin-test-filter extended 255.255.252.252 172.16.1.4 host

  IP 172.30.4.0 allow Access-list l-admin-test-filter extended 255.255.252.252 welcome 172.16.1.2

  access-list extended l-admin-test-filter permit ip 172.30.4.0 255.255.252.252 10.24.0.0 255.252.0.0

  IP 172.30.4.0 allow Access-list l-admin-test-filter extended 255.255.252.252 the host 172.16.0.233

  Protocol-tunnel-VPN IPSec

  Split-tunnel-policy tunnelall

  value by default-field IHI.local

  type tunnel-group L_Admins remote access

  attributes global-tunnel-group L_Admins

  address ili_global pool

  PhoneFactor authentication-server-group

  Group Policy - by default-L_Admins

  IPSec-attributes tunnel-group L_Admins

  pre-shared-key *.

  ++++++++++++++++++++++

  Crossed is not currently enabled, so I guess I have to add:

  permit same-security-traffic inter-interface

  and (I guess)

  mask IP local pool l_admins 172.30.4.1 - 172.30.4.2 255.255.255.252

  Global (outside) 1 interface * PAT IP

  NAT (outside) 1 mask 172.30.4.1 - 172.30.4.2 255.255.255.252

  But from there I don't know how to restrict access to a single external IP on the web on port 80.

  Hello

  Enter the correct command to permit traffic and the same interface of leave is

  permit same-security-traffic intra-interface

  The command you posted allow traffic between 2 different interfaces that have the same value of 'security level'

  permit same-security-traffic inter-interface

  What about PAT Dynamics for Internet traffic

  If you have already

  Global 1 interface (outside)

  Then you will need the command "nat" for the VPN pool

  NAT (outside) 1 172.30.4.0 255.255.255.252

  In what concerns the control of Internet traffic, should not be able to simply add this destination IP address to the VPN filter ACL you have ever used? I mean the ACL named "l-admin-test-filter".

  For example

  L-admin-test-filter access list note allow the external server connection

  access-list l-admin-filter-test permit tcp 172.30.4.0 255.255.255.252 host eq 80

  access-list l-admin-filter-test permit tcp 172.30.4.0 255.255.255.252 host eq 443

  access-list l-admin-filter-test permit tcp 172.30.4.0 255.255.255.252 host eq 8080

  -Jouni

• Access to the Web Service API

  Hello

  I try to access a web page API in the APEX, but still get an error in the ACL.  I tried everything I can think of as well as the multitude of usual information "bits and pieces", which I found on the web.

  USER who needs access to the ACL and the fact that it is an https site makes a difference for settings?

  I can return data from SqlPlus without problem.

  FOR INFO.

  Oracle 11g

  APEX 5

  W2008.

  Pointers would be appreciated!

  Thank you

  Hi Samuistu,

  Samuistu wrote:

  Basically, what I want to do is to download data in a table to a Web site.  A good example of the type of data is here https://www.cryptopia.co.nz/api/GetCurrencies

  Is it possible to get this data into a table that contains the Id column headers, name, etc. of symbol.

  Assuming that you have a table as follows:

  create table crypt_currencies (
    id number,
    name varchar2(128),
    symbol varchar2(8),
    algorithm varchar2(128)
  );
  

  Finally with regard to the features to get the web service data and insert them in the table, for that you can do something like this:

  declare 
  
      l_response clob;
      l_values apex_json.t_values;
      l_data_count integer;
      l_crypt_curr_rec crypt_currencies%rowtype;
  
  begin 
  
      l_response := apex_web_service.make_rest_request (
                          p_url          => 'https://www.cryptopia.co.nz/api/GetCurrencies',
                          p_http_method  => 'GET',
                          p_wallet_path  => 'file:path/to/oracle/wallet',
                          p_wallet_pwd  => 'password' );
  
      apex_json.parse (
          p_values => l_values,
          p_source => l_response );
  
      if apex_json.get_boolean (
            p_values => l_values,
            p_path  => 'Success' ) then
          dbms_output.put_line('Success --> true');
      end if;
  
      dbms_output.put_line ( 'Data Members Count --> '||
                              apex_json.get_count (
                                  p_values => l_values,
                                  p_path  => 'Data' )
                            );
  
      l_data_count := apex_json.get_count (
                          p_values => l_values,
                          p_path  => 'Data' );
  
      for i in 1 .. l_data_count loop
  
          l_crypt_curr_rec := null;
  
          dbms_output.put_line ( 'Id --> '||
                              apex_json.get_number (
                                  p_values => l_values,
                                  p_path  => 'Data[%d].Id',
                                  p0      => i )
                              ||', '||
                              'Name --> '||
                              apex_json.get_varchar2 (
                                  p_values => l_values,
                                  p_path  => 'Data[%d].Name',
                                  p0      => i )
                              ||', '||
                              'Symbol --> '||
                              apex_json.get_varchar2 (
                                  p_values => l_values,
                                  p_path  => 'Data[%d].Symbol',
                                  p0      => i )
                              ||', '||
                              'Algorithm --> '||
                              apex_json.get_varchar2 (
                                  p_values => l_values,
                                  p_path  => 'Data[%d].Algorithm',
                                  p0      => i )
                            );
  
          l_crypt_curr_rec.id := apex_json.get_number (
                                    p_values => l_values,
                                    p_path  => 'Data[%d].Id',
                                    p0      => i );
  
          l_crypt_curr_rec.name := apex_json.get_varchar2 (
                                    p_values => l_values,
                                    p_path  => 'Data[%d].Name',
                                    p0      => i );
  
          l_crypt_curr_rec.symbol := apex_json.get_varchar2 (
                                    p_values => l_values,
                                    p_path  => 'Data[%d].Symbol',
                                    p0      => i );
  
          l_crypt_curr_rec.algorithm := apex_json.get_varchar2 (
                                    p_values => l_values,
                                    p_path  => 'Data[%d].Algorithm',
                                    p0      => i );
  
          insert into crypt_currencies
              values l_crypt_curr_rec;
  
      end loop;
  
  end;
  

  NOTE:

  • The code above is for purposes of example, if you use it make the necessary changes.
  • Dbms_output calls are given for the purpose of debugging. You can remove that in the actual code.

  I hope this helps!

  Kind regards

  Kiran

• virtual access using the web browser

  can I access virtual machine that installed on esxi using the web browser (Internet explorer)

  Hello

  You can access the console of the Web Client vSphere.

  lamw wrote a nice script to generate direct links to consoles, if you want to distribute to other people who are not so familiar with the web client:

  http://www.virtuallyghetto.com/2011/10/how-to-generate-VM-remote-console-URL.html

  He also wrote another script to generate previously authenticated links:

  http://www.virtuallyghetto.com/2013/09/how-to-generate-pre-authenticated-HTML5.html