Activating/Deactivating IEPE power switch for voltage 9234

Similar Questions

• F2 key is no longer active / disable the wifi switch card

  I have laptop Dell mini. The F2 key is no longer active / disables the power switch wifi card. It is always disabled. The device is present, it seems to be a software problem. I uninstalled the drivers and them was reinstalled. I even completely reinstalled Windows 7. Nothing will get my F2 key works again.

  Happy, it's kind of better.

  Consider going to Dell support for new copies of their public services - things with names like

  Dell Wireless enable / disable

  Dell function keys

  that is, no matter what the equivalents are for your system. I just had a peek at one of the Minis because I didn't know you had and these names seem to be utilities controlling the special Dell configured keyboard keys [including F2 is a].

  If you sign in with your Service tag, it just goes to show that you updated utilities & drivers but at the top of the list, right next to a label with your serial number on will be a tab for all models of type - leaf through as you don't care if something is an updated version you need to replace a utility that does not work properly.

  Good luck

• Satellite A100-033 - where to get the cable/connector for power switch?

  Hello

  I change the cable/connector for * power switch button * which connect to motherborad. If anyone no where I can get in? I tried at PC world, but they do not have cable, I am looking.

  My laptop SPAC:

  Satellite A100-033 part number: PSAANE-03J02GEN

  Thank you

  Hi rjbuz,

  I can t tell you the part number because I m not the owner of the Satellite A100, but a service provider authorized in your country can do this:
  http://EU.computers.Toshiba-Europe.com > support & downloads > find an authorized service provider

  Just give them a call and ask. Maybe they can send you the replacement part. :)

• DAQ USB-6008 will be able to power and record voltage for UMS T5 blood pressure at the same time?

  I would use my NI USB-6008 to power my blood pressure monitor UMS T5 (http://www.ums-muc.de/en/products/tensiometer/t5.html) but also to take readings of it, but I don't know if it's possible to do it properly. The power supply for the instrument can be as low as 5V, I can easily get the dedicated + 5V channel. I'm able to feed the instrument and connect it to an analog input on the 6008 and measure a voltage in differential mode. However, when you read the documentation of support for the instrument, I find the following:

  "Potential pitfalls of data acquisition: the pressure transducer is configured in a full Wheatstone bridge, the input voltage and mV signal output can be connected to the same reference (mass)." Therefore, the mV output signal can be measured using a differential voltage measurement. Therefore, do not make an asymmetric measure of pressure transducer mV output. "(http://www.decagon.com/assets/Uploads/MeasuringUMSTensiometerswithnon-UMSControlandDataAcquisitionSystems.pdf)

  My understanding is that the 6008 can take a differential measure if I attach the signal '+' and the signal "-" to the analog inputs of positive and negative terminals. However, it seems that all the ports of ground on the 6008 are grounded to the same reference, which would make my measure of invalid tension according to the above paragraph. So my real question is: if I try to record the voltage with one of the analog inputs on the 6008 in this way, is the valid measurement? Or I need to find a separate power supply, with a different reference field to ensure that the measure is accurate?

  The technical details of this device is very poor. The manual is not much better. Companies that want to sell scientific equipment should publish decent cards or get out of business.

  In section 3.4.3 General requirements the device is described as a "bridge not amplified circuit.  This information along with the impedance of the bridge should be in the specifications, because it is essential to apply the device under any circumstances other than the nominal behavior in 10.6 V.

  The answer to your question is:

  You can use it with the box USB-6008.  The 5 V supply will result in output voltages a little less than half (5/10.6) the voltage specified in nominal conditions. You can use the differential input mode on the box USB-6008.  The absolute input voltages will be approximately 2.5 V with the 5 V power supply. This voltage is in the range of the aircraft. The differences are likely to be less than 100 mV. The resolution of the USB-6008 on the + /-1 V is located about 0.5 mV so your resolution of pressure will be about 1% of full scale. The voltage input impedance and termination of the USB-6008 will present a few errors.  These can be in the order of 5 to 10%. I can't predict much better without the missing bridge impedance specification.  These errors should be relatively constant and systematic. A calibration of the whole system - sensor and together hardware DAQ should allow you to compensate for a large part of this error.

  Lynn

• Compaq Presario SR1522X HELP power switch!

  Help! For the life of me, I can't understand the switch on the front panel. How the hell does it work? My switch will not turn on the computer. I took the front panel off, and I'm completely baffled works even in the switch. Any help would be appreciated.

  Thank you

  Fred

  Hello @Fred_W,

  I understand that your switch does not work and you need assistance. I provide you with a guide on how to make sure it is plugged properly below:

  Step 1. What is the power switch.

  

  The power on / off switch and the hard disk activity and turn on the LEDs are contained in a single module.

  Step 2. Where is the switch?

  

  The module is mounted behind the wall front of the chassis.

  Step 3. How is the power switch set to the chassis?

  

  3 hooks on the module to fix to the wall of the chassis.

  Step 4. When the power switch is connected to the motherboard?

  

  

  I hope that this information helps to answer your question. Given the age of the computer HP is no longer wearing the power switch so if it needs to be replaced, you will need to find a 3rd party distributor. An online search, or possibly a local computer technician must be able to locate the part for your.

  Thanks for posting on the HP Forums. Have a wonderful day!

• What is the best HDMI switch for use with Apple tv 4

  What is the best HDMI switch for use with Apple tv 4. I heard some do not work and the automatic switch has problems because Apple tv is still using power?

  I installed on a cutting and not because the automatic switch works because it isn't always. It came with a remote control that is almost as good, so don't mind the fact that automatic switching does not work well. The reason why I chose cutting is because it was the first device that gave me the good picture and sound quality with my AppleTV, the Xbox 360 and the PS4. (Don't ask!)

• Satellite A110-178 - Toshiba Power Saver for Vista?

  Toshiba Power Saver doest exist for vista? I liked it when you work under XP, but now I switched to Vista Ultimate, and the version of XP does not work under Vist...
  Thanks in advance!

  Hello

  Toshiba has also developed and Power Saver for Vista and will be installed with added Vista package.
  But the energy saving of Toshiba for look of Vista doesn t as the saver of energy for Win XP.

  TOSHIBA Power Saver for Vista belongs to Vista power options, and you can find some additional entries in Vista Power Options.

  But you won't find a stand as only Toshiba Power Saver for Win XP.

  Good bye

• PEAK power switch connector on the EVO d500 D5D Office

  I need a description or a photo of the place where the power cable / HD activity cables and power led cables attact to 17 connector pins on the motherboard.

  I tried the upgrade of the box and failed and the process eliminate their adapter cables.

  Any 1 with 1 there?

  have you tried the site of hp for charts? Maybe the documentation will help you

• Power supply for use in the UNITED Arab Emirates

  Hello

  I just bought a Time Capsule of the airport and an Apple TV (4th gen).  I'm moving to Dubai for work and I intend to take with me.  I can't find out how to replace the power supply for use in Dubai (plug type G).

  • Can I just buy a travel voltage converter?
  • What is the frequency difference (US is 60 Hz and UNITED Arab Emirates is of 50 Hz)?
  • Could I just buy a 'EnergyPal travel Charging Station ETCS04' and connect directly?

  Thanks for any help!

  The airport Time Capsule and the Apple TV work on 100-240 Volts and 50/60 Hz automatically, so they'll work pretty much anywhere in the world if you have the map of the right ankle.  A voltage converter is NOT necessary.

  You can buy the cards you need to any store from the airport, luggage, in Dubai store, etc., most of the hotels the.  If I remember correctly, Dubai uses the same type of plug that she used in the United Kingdom, as well as should work as well.

  http://www.Amazon.com/Ceptics-grounded-Universal-Plug-adapter/DP/B0080R95XI/ref= sr_1_1? ie = UTF8 & qid = 1455557366 & sr = 8-1 & key...

  I do not think that the higher 5 GHz channels are permitted in Dubai, so be sure to put the time Capsule to use a lower numbered GHz 5 channel... 36, 40, 44 or 48.

• LifeDrive power switch broken switch

  Help.  My Lifedrive is 4 years old and has worked well for the old technology.  However, the power switch broke.  In other words, it slips easily rather than move the on/off switch and does not have the power or not.  The last position has been LOCKED.  So I can't enter the data.  A soft reset brings to the top of the screen, but the screen has half shaded numbers and does not recongize being touched or tapped.  There seems to be nothing that works.  A hard reset is not possible because the on/off switch does not work.  Most of my data is synced with my computer.  But I did an interview with oral history and voice Memos do not sync for palm desktop.  So my questions are: 1) does anyone know how to activate a locked Lifedrive with a broken switch for power on / off?  (2) someone knows how to retrieve voice memos to a unit in this condition? (3) does anyone know how to fix a switch broke on a palmOne Lifedrive?  Really hope someone can help.

  

  This is what it looks like after removing the plastic shell.  The piezoelectric speaker is attached to the plastic shell.

  

  Disconnect the battery from the motherboard.  I use a small Flathead screwdriver to separate the connectors softly.

  

  Remove the battery disconnected.

  Write it now, numbers 1 to 4 on the pieces of blue plastic that supports the microdrive; in this way, you won't get lost as all back you together.

  

  The microdrive is connected to the interface of CF. There is a sticker of warning placed on the lower part of the microdrive and interface see cut carefully through the sticker between the CF card and the microdrive with the tip of the knife.  Gently, remove the microdrive from the CF interface with a flat head screw metal or equivalent.

  
  Now the microdrive (in my case, a memory of 32 GB compact flash) is half disconnected from the interface CF.  Continue, making sure not to damage the delicate pins.

  

  Congratulations!  Completely unplugged.

  

  Remove the microdrive (or CF memory).

  

  Disconnect the cable of the microphone of the motherboard in the same way you did to speaker wires.

  

  Unplug the connector for cable film gently with a plastic or equivalent flat head screw.

  You don't want to have cables delicate film cut by accident, so be careful.

  

  Unplug the connector for a another movie cable gently with a plastic or equivalent flat head screw.

  

  Remove the two very short torx screws.

  

  Finally, the motherboard is thrown, and you can see what happened to the switch.

  

  The central internal switch at the top of the motherboard has proved to be in the locked position.

  

  One of the two legs of the plastic piece was found to be broken.  The other leg looked ok.

  

  I slipped inside switch to the unlocked position manually.

  

  Another picture of the internal switch.  If the internal switch turns out to be broken, refer to

  http://1src.com/forums/printthread.php?t=121887 and order a new switch from Mouser Electronics, www.mouser.com
  Part number: 688-SSSS7A0101
  Manufacturer part number: SSSS7A0101
  DESC: SP3T W / BACK WINDOWS
  Switches slide ALPS SMD
  RoHS: compatible

  I think that your internal switch is not broken.

  

  Put the motherboard back such as the plastic piece can slide the internal switch to turn on or off position.  Be careful not to break the other leg healthy in this process!

  Put everything back together carefully.  You start your Lifedrive, you will notice that the date and time are the default, put it so well.   Good luck to you!

• problem with power switch only works a 'cold' start after pushing several times.

  Original title: power switch problem

  The power switch on my computer doesn't work as a 'cold' start after pushing several times.
  Could I have accidentally re-set one "true or false? spend in the registry while trying to solve another problem?
  Dave

  Hello

  Looks like that the power switch has developed a problem, probably about to fail.

  Whatever settings are they should be consistent and not need to several tests.

  Check with a real computer store (the one that makes its own internal and no service
  leeks and glances at a Best Buy or other stores) or system manufacturer support
  (for systems custom Integrator system and the manufacturer in the case of construction of House).

  I hope this helps and happy holidays!

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• 2000-2D02TU HP: HP 2000-2D02TU Power LED power switch but the laptop does not start.

  Someone help me.

  HP 2000-2D02TU Power LED power switch but the laptop does not start.

  What I'm doing.

  Please help me

  Model No. - HP 2000-2D02TU

  Hello @Alok_Bhai,

  Thank you for visiting the HP Forums! A place where you can find solutions for your problems, with the help of the community!

  I read your post on the laptop won't start does not and wanted to help you!

  You indicate that the lights are flashing, but the laptop does not start?  If this is the case, try to review the following document and let me know how it goes:

  Computer does not start and emits a LED or beep Code

  Please let me know if this information helps you solve the problem by marking this message as 'accept as Solution' , this will help others easily find the information they seek.  In addition, by clicking on the Thumbs up below is a great way to say thank you!

  Have a great day!

• Pavilion a6512p power switch wiring / card mother pinset

  Looking for a diagram or pinset for Pavilion a6512p desktop pc.

  A friends PC is DEAD.  Then as he would not pass a person removed the power switch and the switch wiring.

  I try to find why the PC is DEAD.  Good power - LED to a constant.

  Need to go beyond the power switch isssue so need to know how to wire lift PC to power.

  So I can determine if it is the switch power supply or component...

  Any help would be appreciated.

  Should be a diagram somewhere telling me what PIN does what.

  TIA, Gary

  Please use the following scheme;

  

  If you have any other questions, feel free to ask.

  Please click the 'Thumbs Up' white LAURELS to show your appreciation

• The A3-A20-K1AY support automatic power switch with flip covers?

  I just bought this Iconia and a folding cover to go with it. I can't find anywhere in the settings to activate automatic power switch. Now, I wonder if this tablet has even this feature.

  Yes, he does not sleep automatically when you close the lid. Better to use the button for this.

• 7000n: power supply for scanner HP 7000n

  Got a scanner 7000n with lack of power.

  Anyone who can give the plug for the power required?

  The connector is slightly unusual one, but that should be possible to work around.

  It has 3 pins - if someone can supply what voltage goes on which pin that would be outstanding!

  Or if there is a replacement part available HP which is an option too, have not been able to find that so far well.

  Thank you.

  Some additional Googling turned up this:

  Spare parts for the scanner HP 7000: http://partsurfer.hp.com/Search.aspx?SearchText=L2709A

  The power brick is part # 0957-2260 (32 VDC, 180W):

  ' 2260-0957: . "Power - input module voltage 100-240 VAC output voltage 32VDC, 180 watts - requires a separate 3-wire power cord with connector C13.