Add remote host OME Discovery Range Group

Similar Questions

• CX3-20: host in several storage groups?

  Hi all

  What is the trick? I have all the storage groups created on our SAN access to our server VCB (Virtual Consolidated Backup of VMware).

  The problem is that our Clarion EMC Cx3-20 allow us only to add a host to a storage group.

  If I want to connect the VCB server to a different storage group, I get a prompt saying (in Navisphere):
  AMS - back.corp.com: this host is already connected to a different storage group. Connection to the current storage group will be be disconnected from the other storage group. This will cause the host unable to access the LUNS that are in the other storage group.

  VCB server must see all LUNS, can advise you?
  Thank you

  
  

• Cannot add cluster hosts

  I'm done with this...

  It started when I had to change my non routable IP addresses management network to my private IP addresses.  I kept getting errors with the host, not the new IP address.  I solved this problem, but now when I try to add the hosts again in my group, I get an error:

  "A general error has occurred: passwd: error immediate criticism-abandonment."  blah blah blah stack of error: "unable to set the account VIM on the host, could not set the password. It is possible that your password does not meet the criteria of complexity defined by the system. »

  It is ESXi 5.5u3, I tried the following:

  Remove the vpxa account, restarted host - same mistake

  Restart the services vpxa - same mistake

  Restart the vCenter - same mistake

  VI etc/pam.d/passwd: N0, N1, N2, N3, N4 - same mistake

  VI etc/pam.d/passwd: n0=-1,n1=-1,n2=-1,n3=-1,n4=-1--meme error

  Checked the system authentication, do not know what its supposed to look like, but both hosts match

  For the life of me, I can't understand it and Google has basically the same steps that I have just listed, I don't want to really blow the configuration and reinstall, but he is looking to get down to that... unless someone here knows where else the complexity of password or criteria for the system is set up...

  Fixed the problem myself... Thank you!!

  Action taken:

  Removed the vpxa account - I don't really think this has no effect on the issue

  Retirement services - did nothing until I've known really

  After coming home and watching my esxi, pam.d file hosts and comparing the differences, I just on a hunch deleted after /$ISA / pam_passwdqc.so, then re-entered the information as it was on my host at home.

  SSH in hosts:

  cd\ etc.

  PAM.d cd\

  passwd VI

  My hosts had /$ISA/pam_passwdqc.so retry = 3 min = disabled, disabled, disabled, disabled, 7.7

  My hosts at work had /$ISA/pam_passwdqc.so retry = N N0, N1, N2, N3, N4

  I edited the line to reflect the password of 14 characters required and the value of the retry N, so it looked like this

  /$ISA/pam_passwdqc.so retry = N min = disabled, disabled, disabled, disabled, disabled, 14

  : wq

  output

  Restart the services, actually I rebooted the host, then add in vCenter without problem

• TAC +: TCP/IP open to 10.20.17.2/49 failed - connection has expired; remote host does not

  GANYMEDE + configured on the router and the router is in ACS.  I can ping from the ACS, but the router cannot establish a connection to authenticate users.

  AAA server Ganymede group + hq_acs-1

  Server 10.20.17.2

  Ganymede IP source-interface GigabitEthernet0/0

  !

  AAA authentication login default group Ganymede + local

  AAA authorization config-commands

  AAA authorization exec default group Ganymede + local

  AAA authorization commands by default group Ganymede + local 10

  AAA authorization commands 15 default group Ganymede + local

  nested AAA accounting

  AAA accounting newinfo periodic update 60

  AAA accounting auth-proxy default start-stop Ganymede group.

  AAA accounting exec default start-stop Ganymede group.

  orders accounting AAA 15 by default start-stop Ganymede group.

  AAA accounting network default start-stop Ganymede group.

  Default connection accounting AAA power Ganymede group.

  AAA accounting system default start-stop Ganymede group.

  AAA accounting resource by default start-stop Ganymede group.

  BigTree_3945 #sh ip int br

  Interface IP-Address OK? Method State Protocol

  GigabitEthernet0/0 10.4.3.1 YES NVRAM low low

  GigabitEthernet0/1 10.12.10.26 YES NVRAM up up

  Serial0/2/0 unassigned YES NVRAM low low

  Serial0/2/0.602 10.12.15.10 YES NVRAM low low

  11:08:13.673 Apr 13: MORE: Queuing AAA request authentication 79 for the treatment

  11:08:13.673 Apr 13: MORE: treatment demand beginning 79 authentication id

  11:08:13.675 Apr 13: MORE: authentication start package created for 79 (cisscdb)

  11:08:13.675 Apr 13: MORE: using the 10.20.17.2 Server

  11:08:13.675 Apr 13: HIGHER (0000004F) / 1BDD9C34/NB_WAIT/0: started 5 sec timeout

  11:08:18.676 Apr 13: HIGHER (0000004F) / 0/NB_WAIT/1BDD9C34: expired

  11:08:18.676 Apr 13: HIGHER (0000004F) / 1BDD9C34/NB_WAIT/0: expired, cleaning

  11:08:18.676 Apr 13: HIGHER (0000004F) / 0/1BDD9C34: the package of treatment response

  11:08:25.834 Apr 13: MORE: Queuing AAA request authentication 79 for the treatment

  11:08:25.834 Apr 13: MORE: treatment demand beginning 79 authentication id

  11:08:25.834 Apr 13: MORE: authentication start package created for 79 (cisscdb)

  11:08:25.834 Apr 13: MORE: using the 10.20.17.2 Server

  11:08:25.834 Apr 13: HIGHER (0000004F) / 1BDD9C34/NB_WAIT/0: started 5 sec timeout

  11:08:30.836 Apr 13: HIGHER (0000004F) / 0/NB_WAIT/1BDD9C34: expired

  11:08:30.836 Apr 13: HIGHER (0000004F) / 1BDD9C34/NB_WAIT/0: expired, cleaning

  11:08:30.836 Apr 13: HIGHER (0000004F) / 0/1BDD9C34: the package of treatment response

  11:08:43.689 Apr 13: TAC: using default Ganymede groups ' Ganymede"list."

  11:08:43.689 Apr 13: TAC +: opening TCP/IP 10.20.17.2/49 Timeout = 5

  11:08:51.057 Apr 13: MORE: Queuing AAA request authentication 79 for the treatment

  11:08:51.057 Apr 13: MORE: treatment demand beginning 79 authentication id

  11:08:51.057 Apr 13: MORE: authentication start package created for 79 (cisscdb)

  11:08:51.057 Apr 13: MORE: using the 10.20.17.2 Server

  11:08:51.057 Apr 13: HIGHER (0000004F) / 1BDD9C34/NB_WAIT/0: started 5 sec timeout

  11:08:54.692 Apr 13: TAC +: TCP/IP open to 10.20.17.2/49 failed - connection has expired; remote host does not

  11:08:54.692 Apr 13: MORE: Queuing AAA accounting request treatment 76

  11:08:54.692 Apr 13: MORE: treatment of the accounting application id 76

  11:08:54.692 Apr 13: MORE: sending AV task_id = 332

  11:08:54.692 Apr 13: MORE: sending AV timezone = EDT

  11:08:54.692 Apr 13: MORE: AV = shell shipping service

  11:08:54.692 Apr 13: MORE: sending AV start_time = 1334329734

  11:08:54.692 Apr 13: MORE: sending AV priv-lvl = 15

  11:08:54.692 Apr 13: MORE: sending AV cmd = show logging

  11:08:54.692 Apr 13: MORE: request for accounts created for 76 (n20j03t)

  11:08:54.692 Apr 13: MORE: using the 10.20.17.2 Server

  11:08:54.692 Apr 13: HIGHER (0000004C) / NB_WAIT/1/20FD90EC: started 5 sec timeout

  11:08:56.058 Apr 13: HIGHER (0000004F) / 0/NB_WAIT/1BDD9C34: expired

  11:08:56.058 Apr 13: HIGHER (0000004F) / 1BDD9C34/NB_WAIT/0: expired, cleaning

  11:08:56.058 Apr 13: HIGHER (0000004F) / 0/1BDD9C34: the package of treatment response

  11:08:59.693 Apr 13: HIGHER (0000004C) / NB_WAIT/1/20FD90EC: expired

  11:08:59.693 Apr 13: HIGHER (0000004C) / NB_WAIT/1/20FD90EC: expired, cleaning

  11:08:59.693 Apr 13: 1/HIGHER (0000004C) / 20FD90EC: the package of treatment response

  BigTree_3945 #.

  The AAA Client IP address	10.4.3. * 10.12.15.10
  Key
  Group of network devices	Test NJT AccessLink (Not assigned)
  Authenticate using	GANYMEDE + (Cisco IOS) RADIUS (Cisco Aironet) RADIUS (Cisco BBSM) RADIUS (Cisco IOS/PIX) RADIUS (Cisco VPN 3000) RADIUS (Cisco VPN 5000) RADIUS (IETF) RADIUS (Mount) RADIUS (Juniper) RADIUS (Nortel) RADIUS (Sepi)
  Connect GANYMEDE + single AAA Client (stop recording in accounting in case of failure).

  The 10.12.10. range * is listed under the HQ site.

  Your help is greatly appreciated.

  You said that you can ping the router ACS, have you tried the GigabitEthernet 0/0 interface packages (that is those THAT GANYMEDE + will attempt to use, given the configuration you have posted) supply?

  What is the network path between the router and look like ACS (IE, a firewall, NAT, etc.)?

  Can you connect to port 49 to the IP address of the router GBA, GigabitEthernet 0/0 of supply packages?

  Using VRF?

  Which version of IOS?

• Existing connection had to be closed by the remote host

  Need help with this error
  I have a dev and a uat environment.
  I have a small form that I use as a method to call a web service. Essentially, the form contains a web service URL text box.
  If I call the shape on the dev and pointer to the service web dev, it works.
  If I use the form on uat and point the service web uat it works.
  If I use the form on UAT and call the web service on dev, it works.
  However, if I use the form on the dev and point the web service uat I get this error:

  In the Application Server error ' / '. An existing connection was to be closed by the remote host Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and its origin in the code.

  Exception details: System.Net.Sockets.SocketException: An existing connection was to be closed by the remote host

  Source error:

  The source code that generated this unhandled exception can only be shown when compiled in debug mode. To do this, follow one of the below steps, then request the URL: 1. Add a "Debug = true" directive at the top of the file that generated the error. Example: <%@ Page Language="C#" Debug="true" %> or: (2) add the following section to the configuration file of your application:                 Note that this second technique, all the files in an application to be compiled in debug mode. The first technique will make only this file to be compiled in debug mode. Important: Running applications in debug mode causes a memory/performance load. You must ensure that an application has debugging disabled before deploying to the production scenario.

  Stack trace:

  [(0 x 2746) SocketException: an existing connection was to be closed by the remote host] System.Net.Sockets.Socket.Receive (Byte [] buffer, Int32 offset, Int32 size, SocketFlags socketFlags) + 73 System.Net.Sockets.NetworkStream.Read (Byte [] buffer, Int32 offset, Int32 size) 131 [IOException: unable to read data from the transport connection: an existing connection was to be closed by the remote host.] System.Net.Sockets.NetworkStream.Read (Byte [] buffer, Int32 offset, Int32 size) + 294 System.Net.PooledStream.Read (Byte [] buffer, Int32 offset, Int32 size) + 26 System.Net.Connection.SyncRead (request of HttpWebRequest, Boolean userRetrievedStream, Boolean probeRead) + 297 [WebException: the underlying connection was closed: an unexpected error occurred during the reception.] System.Net.HttpWebRequest.GetResponse () + 5399741 _Default.btnTestUpload_Click (Object sender, EventArgs e) + 532 System.Web.UI.WebControls.Button.OnClick (EventArgs e) 111 System.Web.UI.WebControls.Button.RaisePostBackEvent(String eventArgument) + 110 System.Web.UI.WebControls.Button.System.Web.UI.IPostBackEventHandler.RaisePostBackEvent (String eventArgument) + 10 System.Web.UI.Page.RaisePostBackEvent (IPostBackEventHandler sourceControl, String eventArgument) + 13 System.Web.UI.Page.RaisePostBackEvent (NameValueCollection postData) + 36 System.Web.UI.Page.ProcessRequestMain (includeStagesBeforeAsyncPoint, Boolean, Boolean includeStagesAfterAsyncPoint) 1565

  Version information: Microsoft .NET Framework Version: 2.0.50727.4234; ASP.NET Version: 2.0.50727.4223

  Any ideas?

  Hello

  I suggest you for this post in the appropriate section of the form of MSDN

  http://social.msdn.Microsoft.com/forums/en-us/categories/

  I hope this helps.

• Cannot add a host - you do not hold independent privilege add host

  I'm trying to add a host to my data center that was there before (taken out to solve a problem) and I can't do it.

  I get the error:

  Refused permission to perform this operation.

  "You do not privilege" Home > inventory > Add standalone host "on data center xyz.

  This may be the cause?

  -ar

  Well I checked the membership to the Group on the subject of data center and found that I was in a group that had only READ access. Myself removed from the Group and everything is fine. Thanks for all the suggestions!

  ... AR

• Cannot run add a host vCAC to vCO

  I tried to run the workflow 'Add a host vCAC' and continues with invalid credentials.  I tried the account a local administrator on the system of IaaS, an AD that is in the Administrators group and the based AD account service IaaS components are installed as.  None of them have worked.

  How can I dig deeper to understand what is malfunctioning and what I need for this power?

  Someone at - he was able to do with AD to service account?

  Solution:

  Setup

  • ROOT domain credentials are named vCACp
  • Credentials of field CHILD named vCACt
  • IaaS server is in the field of CHILD
  • ROOT & CHILD have a two-way trust relationship.

  ROOT\vCACp & CHILD\vCACt to the administrator group on IaaS.Child.local

  Admission tests

  Go to https://iaas.child.com/repository/data/MetaModel.svc/ and put in

  ROOT\vCACp credential and it works very well.  It returns the XML code.

  CHILD\vCACt credential and it works very well.  It returns the XML code.

  If the permissions work on the side of IaaS.

  Go to vCO and run the "Add to vCAC host" and put in vCACp ID with the Netbios name of the ROOT.  Breaks down...

  Try again with vCACt using the netbios name of the CHILD... work properly.

  Apparently, there is a limitation/known issue with the use of vCO and cross domain trust.   Not sure of the details and am still digging for a Ko or a few other details about this.

• Unable to connect to the MKS: the certificate of the remote host has these problems:

  Hello

  We have a host of ESXi 4 cluster running any vSphere 4.1.  Recently, I started to upgrade to update 2 and all the additional fixes.  After the upgrade of the vCentre server to the latest version (or maybe before I can't noticed) an of are hosts began to show the following error whenever I tried to connect to the console of any guest on this host.

  Unable to connect to the MKS: the certificate of the remote host has these problems:

  It lists any problems at all and no error display in the event log that it simply does not work.  I had a prod around the internet and found nothing.  I then rebuilt the host to exclude and the problem remains.

  Any help would be much appreciated.

  Thanks in advance

  David

  If you can connect to the Console remotely using VMware Infrastructure (VI) Client connected directly to the host, take a look at vmware KB to connect to a remote virtual machine fails with the error: the certificate of the remote host has these problems

  but more generally - remove host to vCenter inventory and then add the host to the back, take a look at opening in the console of the virtual machine after a new installation of ESXi or ESX fails with the error: the host certificate chain is not complete and could not connect to the MKS: the certificate of the remote host has these problems

• Cannot add Ubuntu host physical hard drive to Windows 7 comments

  When I try to add a physical hard disk to a Windows 7 client on an Ubuntu host, I get the error: "insufficient permission to access file. This occurs if the drive is mounted on Ubuntu or not. In Ubuntu, permissions on records House / < username > / vmware and/dev/sdc have rwx was set by "chmod-r 777 vmware."

  Steps to follow:

  -Launch the Virtual Machine settings
  -Add the hard drive; Use a physical disk
  -Device is/dev/sdc (connected by eSata to the host of Ubuntu)
  -Use: Use the entire disk
  -Name of the disk file: Windows7x64 - 0.vmdk
  -"Finish" produces the error message. Steps to follow:

  The hard drive is connected via eSATA. The error message occurs if the disk is mounted or not in Ubuntu. It also occurs if I try to add a partition, but the folder is/dev/sdc.

  Ubuntu 9.10 64-bit, Windows 7 Ultimate 64 - bit comments host.

  It's probably something obvious to a Linux expert...

  This is expected behavior

  Run WS as root - or try to add your user account to the Group of disks-

• Add the user to the users group in the Users.ini file using c#

  Hello

  Using a c# application, we strive to add/remove a user from the TestStand Users.ini file.

  The CreateDeleteUsers.seq file in the samples of TestStand is used as a reference.

  We have seen that we are able to add the user to the list of user help file

  engine. UsersFile.UserList.SetPropertyObjectByOffset (0, 0 x 1, newUser.AsPropertyObject ());

  However, when we try to add the user to the user group, the sample file CreateDeleteUsers.seq said

  RunState.Engine.GetUserGroup (Locals.GroupName). Members.SetPropertyObjectByOffset (0, 0 x 1, Locals.User.AsUser.LoginName)

  If we try to replicate this in c#, the API seeks the last parameter (which is LoginName in the CreateDeleteUsers.seq file) as an object of property

  engine. GetUserGroup (this.) GroupName). Members.SetPropertyObjectByOffset (0, 0 x 1, newUser.AsPropertyObject ());

  This causes an exception of object reference when we run the application.

  Please advise on how to proceed.

  Thank you

  Arun-

  The members property is an array of string, so the 3rd parameter to SetPropertyObjectByOffset requires a string property object, IE. the user name and not of the user object. From the will of the user object error with '-17308; Specified value is not the expected type. ». The example should really be using SetValStringByOffset to be clearer so that you only specify the user name of the actual string.

• An existing connection to be closed by the remote host.

  Since last week, I can't keep a connection to the server of vatsim or acars for virtual pilots micro flight simulator will for more than five minutes. the error message is that an existing connection had to be closed by the remote host

  not an expert of anymeans and all the answers I got on the net are well above my paygrade.

  Hi dva8377,

  Here are two additional methods you can try.

  1: Restart the computer by using a clean boot of the method

   

  When you start Microsoft Windows, other software may start with the operating system. These programs may include antivirus software and system programs that may interfere with the game. When you perform a clean restart procedure, you prevent these programs from starting automatically.

  Reference:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  Method 2: Bypass the router

   

  If you connect to the Internet using a router, there may be a problem with the configuration settings, which requires that the updated settings. To determine if a network connectivity problem is caused by a bad configuration or a problem affecting the router, try bypassing the router by connecting your computer directly to the modem. Remember that this test will only check that the router is configured correctly. If the game connects to the Internet without problem when you bypass the router, plug the router immediately and contact the manufacturer of the router or your ISP for help configure the router correctly.

  Note: Ensure that you switch your computer to normal startup mode after completing the troubleshooting steps. Steps are available in the article above.

  For more information, see: http://www.microsoft.com/Products/Games/FSInsider/tips/Pages/default.aspx

  Kind regards

  Shinmila H - Microsoft Support

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Unable to ping the remote host IP address

  I have a home network with 2 desktop computers, printer, TV and BlueRay attached.  The PC is both XP and members of the same workgroup.  I can't get the connectivity between the PC 2.  With 1 PC, I ping successfully all connected devices, with the exception of 2 PC.  2 PC, I ping equipment successfully connected, including 1 PC...  I get the same information using a different router and a different network on 2 PC card.

  I tried the following steps of the Article 314067:

  1. check on two PC's TCP/IP configuration.  Result: good on both PCs.

  2. use the ping tool to test connectivity.

  • Ping the loopback address.  Result: good on both PC
  • Ping to the IP address of the local computer.  Result: good on both PC
  • Ping the IP address of the default gateway.  Result: good on both PCs.
  • Ping to the IP address of the remote host.  Result: bad on PC 1, good on PC 2
  • Ping other IP addresses on the network.  Result: good on both PCs.
  • Ping the host name of the other PC.  Result: bad on PC 1, good on PC 2

  Article:

  If the ping command fails, the remote host may not be responding, or there may be a problem with the hardware of network between computers. To the rule

  on a remote host does not respond, use Ping again to a different remote host.

  If you cannot use Ping successfully at any time, verify the following configurations:

  1. Make sure that the IP address of the local computer is valid and that it is correct on the

  Tab general of the Internet Protocol (TCP/IP) properties dialog or box when it is used with the Ipconfig tool.  Result: good on both PC

  Make sure that the default gateway is configured and that the link between the host and the default gateway works. For the purposes of troubleshooting, make sure that this gateway by default is configured. You can configure multiple default gateways, gateways after the first gateway is used only if the IP stack determines that the original gateway is not working. Diagnosis is to determine the State of the first configured gateway. Therefore, you can delete all the other gateways to simplify your task.  Result: good on both PC
  Make sure that Internet Protocol security (IPSec) is not enabled. According to the IPSec policy, Ping packets may be blocked or may require security. For more information about IPSec, go to method 7: Verify Internet Protocol security (IPSec).  Result: good on both PC

  Thanks for your suggestions you may have.

  Hello

  Firewall such as Norton, McAfee etc can cause a loss of network connectivity, even when the network is correctly configured. Try disabling the firewall on both computers to see if the ping works.

  Tricky

• Diagnostics network ping to the remote host, but has not received a response

  I'm trying to figure out if there is a problem with just my laptop not wanting to connect to a local free WiFi, so any help is appreciated. He worked two days ago only to stop abruptly last night.

  Windows Network Diagnostics comes back with the error message "Can not contact www.microsoft.com (65.55.12.249)" and "diagnostic network ping to the remote host, but has not received a response.

  The only repair option it evokes is ' reset NIC 'wireless network connection ' '.

  I can always connect to WiFi using my iPhone, and even a connected laptop computer work Companion. Yet once, if this can be fixed on my end, any help would be appreciated.

  Hello BrenJones,

  Thanks for posting back. DNS servers are controlled by your ISP. I communicate with your Internet service provider and confirm that you have the good DNS for your network.

  Hope this helps J

  Adam
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Remove a remote host from monitoring Infrastructure

  How can I go about removing a host of infrastructure monitoring?  If the host has its own fglam, I was able to disable the agent simple, remove fglam, etc..  In this case, I see no option to turn off monitoring, or withdraw completely from the remote host monitoring.

  In the screenshot below. Let's say that I simply wanted to see information of the rd-r220-01.  But I always wanted my central collector collect statistics on all remote hosts.

  See you soon,.

  Seth

  If I wanted to stop monitoring of the vmebizjmc of the host, I'll stop the WindowsAgent. In the screenshot you can see other officers running from the host even where a foglight agent Manager is running. I can't stop foglight agent manager.

  

  David Mendoza

• Add a contact to an established group of Windows Live Mail

  Original title:

  Windows Mail life 2012

  How can I add a contact to a defined group (now called category?).

  Switch to the contacts window by pressing Ctrl-3 or by clicking the address book at the foot of the folders pane. Right-click on the relevant contact and select Copy Contact to.  You can then choose the category you want to add the contact to.