Address resolution protocol

I have a question regarding the Protocol address resolution.

Suppose that a network device enters a network where the trafficking involves UPnP messages among other things.

How the device will start its cache ARP Table fill?

My understanding is that the following sequence takes place...

1. the unit can receive a UPnP discover message, it must take into account.

2. now, he already has the MAC address of the bridge while attribution of IP through DHCP.

3. it sends a response to the entry door, because he does not know the MAC address of sender tha of the UPnP message.

4. the bridge takes care to send the message to the destination MAC address.

5. after sending the response, the device to update its ARP table by sending ARP messages to the sender of the previous UPnP message.

I hope that I don't confuse anyone!

Basically any network device that I'm trying to ask is do an entry in its ARP table before you reply to the sender of a message to the network?

Or she will leave the bridge deal with it and take care of the ARP table entry later (see above)?

see you soon,

Gandalf

I don't see the contradiction between 2 and 4. One is for the unicast and the other for the multicast/broadcast. Suffice to say, that a computer that receives something captures the information contained in the ARP table.

He enters information in the ARP cache because that's how it works. Remember that the ARP and the management of entire ARP cache is at a very low level in the communication stack. All of the ARP is located somewhere in the "context". Programs only communicate using the intellectual property and will just send something to an IP address. Everything, that is, ARP, routing, etc. is done automatically in the operating system.

Of course, it can always be that the person who receives something has no answer. But how the Protocol IP or ARP knows he won't? It is much easier and faster to store the information anyway. It is stored for 5 minutes. If this is not necessary it won't really hurt. If it is necessary it is already there and should not start another ARP request to find the MAC address of the original sender to answer now. For example, you store information that you have learned. You store the information if you receive an ARP request for your IP address, and in other cases.

With regard to the last question: it depends on what is the 'message '.

All communication over ethernet (wired or wireless) using MAC addresses. Always. It matters little whether unicast, multicast, or broadcast. The latter two uses special MAC addresses, but that's all. An ethernet frame always contains an address MAC of the sender and the receiver. Always.

Frames Ethernet with any protocol you like. If it contains no IP packets, there are no contained IP addresses. If it contains an IP packet there are IP addresses.

Thus, a multicast ethernet or broadcast may or may not contain IP addresses according to what is content. If this is not IP there is no IP address

Any communication using IP (regardless of the Protocol below) has IP addresses. It matters little whether unicast, multicast, or broadcast. An IP packet always contains the IP address of the sender and the destination. broadcast and multicast addresses are just special IP addresses.

When you send IP through an Ethernet the image on the thread will contain the IP address and MAC. When you send the IP through a network ATM frames will contain the IP and ATM addresses. IP and 'carrier' protocol that is used on the physical media connecting the two devices are entirely independent.

Of course, the most common installation in a House that LAN (many other sources) is usually a LAN ethernet, which means that you are running IP over ethernet within your local network.

Tags: Linksys Routers

Similar Questions

  • The Peer Name Resolution Protocol service (PNRPsvc) or peer network (p2pimsvc) Identity Manager service does not work

    I get the following error message when you run windows network diagnostics. I ran the diagnosis because I have a network with Win 7 Ultimate 64 bit on a computer and WinXP 32 bit on the other.  Curiously, I can easily see and manipulate all files through the firewall of Windows XP. Either way, Windows XP can not see files on Win7. I can drag files to the shared folder, XP can see them, but can not open the same when I enable the share using Win7.  I can see the Win7 computer name and I have a home network without password. When I click on the folder with XP, the error popup grey box says that I might not have permissions to access these files. Contact the administrator of systems etc. My network has the same name on both computers, so I feel totally betrayed by what is happening here. There should be no problem but there is a.

     

    I get this error message when you run windows network diagnostics:

     

    The Peer Name Resolution Protocol service (PNRPsvc) or peer network (p2pimsvc) Identity Manager service does not work, The Peer Networking Grouping (p2psvc) service depends on these two services to work correctly

     

    I've followed these tips nothing does not:

     

    ·                                                                                                                                                                                                                                                     To see which services are/are not running click on the ORB start and type Services in the search box at the bottom of

    the menu. Select Services results.

    Check the columns of type status and commissioning for "Start" and "Manual".

    Those who are not running, then select properties in the right click menu.
    Click the startup type box and select manual in the menu, then click on apply, then OK at the bottom of the window.
    Now try to Start the service for the option in the main window.
    Try the homegroup connection, if the service starts

    Try a reboot if all goes well. The settings may or may not stick!

    Scroll down the page until you see the following...
    Select Services results.

    Hi MarkWebber,

    Method 1: I suggest you to follow the link provided below to start your computer in safe mode with network.

    Advanced, including safe mode startup options

    http://Windows.Microsoft.com/en-us/Windows7/advanced-startup-options-including-safe-mode

    If it works fine in safe mode with network, try to put your system at startup mode minimum state helps determine if third-party applications or startup items are causing the problem. If so, you need to maybe contact the manufacturer of the program for updates or uninstall and reinstall the program.

    See the following article in the Microsoft KB for more information on how to solve a problem by performing a clean boot in Windows Vista or Windows 7:

    How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

    http://support.Microsoft.com/kb/929135

    Note: After troubleshooting, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

    Method 2: Studied the problem and found the solution. A file has been corrupted and remove he got running PNRP service. The file has been re-created correctly when the PNRP service started upward. Here is the file for future reference:

    'C:\Windows\ServiceProfiles\LocalService\AppData\Roaming\PeerNetworking\idstore.sst'.

    Hope this information is useful.

  • How to fix Peer name resolution Protocol (PNRPsrvc) Service or Peer Networking Identity Manager Service (p2plmsrvc)

    How can I fix Peer name resolution Protocol (PNRPsrvc) Service or Peer Networking Identity Manager Service (p2plmsrvc)?

    Hello

    1. do you get any error message related to name resolution Protocol Service by peers or Peer Networking Identity Manager Service?

    2. the performance of the computer is made?

    3. were there any changes (hardware or software) to the computer before the show?

    Make the SFC (System File Checker) scan and see if the problem occurs.

    How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

    Hope this information helps.

  • Cannot start the peer name resolution protocol Protocol

    No p2p service means no homegroup, which means no access to other computers or to the wireless printer... He worked a few months ago, and now, the protocol name resolution by peers, well defined to automatic, does not start, even if I click on properties, etc. and ask him to startr. I have ' windows cannot start the Protocol PNRP, error 0 x 80630203.»

    I still have unresolved problems with backups, so I don't want a new installation of windows.
    I'm getting so fed up with all the unsolved problems of windows! is windows 8 is going to be better?
    Thanks for your help.

    Hello

    Please keep us updated.

    You can read the articles below and see if it helps:

     

    Add a device or computer to a network

    http://Windows.Microsoft.com/en-us/Windows7/add-a-device-or-computer-to-a-network

     

    Share files via public folders

    http://Windows.Microsoft.com/en-us/Windows7/share-files-using-the-public-folders

    If you need further assistance, please answer and we will be happy to help you.

  • My laptop connects to the network but has no access to the internet.

    Another 169.254.x.x problem...

    I watched a lot of discussions about this problem and I tried methods in them, but still no go.

    Laptop Toshiba Satellite P300-061 / SP 2 / Vista Home x 64

    I've been connected wireless with my laptop and my desktop (with an adapter) with no problems at this cottage for about 3 to 4 days.
    Last night, I turned off the ability to laptops to detect the networks with the small button on the side, as I sometimes do.

    I turn it back on today and the laptop detects the network, but it doesn't connect to the internet. If I have limited connectivity.
    I restarted approximately 3 - 4 times and the laptop doesn't always connect. I am currently connected wirelessly on this network with my office and it works fine so that indicates that it is related to the laptop and not the router.  At first, I thought it might be a hardware problem, the laptop detects the network in the list, but it also detects the surrounding networks, which means that the wireless card works.

    ---

    Things I've tried so far.

    1 netsh winsock reset / netsh int ipv4 reset
    2 ipconfig / renew & enough & / flushdns & / registerdns
    3 Rename the connection
    4 restart / complete closure
    5. deletion of the network in the list and return the password
    6 disabling ipv6
    7 try to put the news in ipv4 manually, even though I'm not sure I did it correctly
    8 turn off the firewall
    9 uninstalling the wireless card and reboot
    10. system restore

    I'm really in the ideas and I would appreciate help, maybe I'm not the steps in the correct order, or something.
    I tried my best to search the net for a solution but they do not seem to work, and I'm really in ideas.

    Thank you for taking the time to read my thread and to help me.
    -John

    Edit: I would also add that it gives me the IP 169.254.x.x over any wireless network, I connect to.

    Hi modsiw and VioletStar,.

    You guys might already made with Gloria but give it another go on your system

    Clear ARP table

    Use the NetShell (netsh) command to erase, delete, or refresh the cache of the ARP (Address Resolution) protocol using the following steps.

    1. Click the Start button.
    2. Click the command run and type Cmd in the box text run, and then press ENTER. For Windows Vista, type Cmd in start search and press Ctrl-Shift-Enter keyboard shortcut
      to force the administrator privileges. Enter the Administrator user ID and password and allow any request for authorization when you are prompted.
    3. In the command prompt window, type the following command, and then press ENTER.
      netsh interface ip delete arpcache

    The command works in Windows Vista, Windows XP and Windows 2003.

    RESET TCP/IP ATTACH IT TO THE TOOL

    http://support.Microsoft.com/kb/299357

    REPAIR WINSOCK RESET TOOL

    http://support.Microsoft.com/kb/811259

    Let us know if this helps,

    Kevin
    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think.

  • Connectivity lost in the dmz (pix) and answer arp

    Good afternoon. I have the pix 515e with 6 interfaces.

    PIX firewall-firewall # sh ver

    Cisco PIX Firewall Version 6.3 (3)

    Cisco PIX Device Manager Version 3.0 (1)

    Updated Thursday, August 13 03 13:55 by Manu

    Material: PIX-515E, 64 MB RAM, Pentium II 433 MHz processor

    Flash E28F128J3 @ 0 x 300, 16 MB

    BIOS Flash AM29F400B @ 0xfffd8000, 32 KB

    The computers placed in the demilitarized zone, sometimes lose the connection with the other. Found a following problem: to arp request sent by a computer, it receives the response and the necessary computer and pix.

    IP address on the interface of the pix (dmz) - 172.21.35.1

    Test connectivity to the computer with the IP 172.21.35.5 to clear the arp table:

    ping 172.21.35.4

    Ping 172.21.35.4 with 32 bytes of data:

    Reply from 172.21.35.4: bytes = 32 time<1ms ttl="">

    Request timed out.

    Request timed out.

    Request timed out.

    Ping statistics for 172.21.35.4:

    Packets: Sent = 4, received = 1, Lost = 3 (75% loss),

    After ping:

    > arp - a

    Interface: 172.21.35.5 - 0 x 10003

    Internet address physical address type

    172.21.35.1 00-0d-88-ef-23-29 Dynamics

    172.21.35.2 00-0d-60-ec-85-32 Dynamics

    172.21.35.4 00-0d-88-ef-23-29 Dynamics

    very strange: address Macs.1 same et.4

    Ethereal, running on the same computer:

    N ° time Source Destination Protocol Info

    1 0.000000 172.21.35.4 broadcast ARP which has 172.21.35.1? Say 172.21.35.4

    Image 1 (106 bytes on wire, 106 captured bytes)

    Ethernet II, Src: 172.21.35.4 (00:11:25:57:f9:2 c), Dst: Broadcast (ff: ff: ff: ff: ff: ff)

    Address Resolution Protocol (request)

    N ° time Source Destination Protocol Info

    2 1.381832 172.21.35.2 172.21.35.5 ARP, who has 172.21.35.5? Say 172.21.35.2

    Frame 2 (60 bytes on wire, 60 bytes captured)

    Ethernet II, Src: 172.21.35.2 (00: 0d: 60:ec:85:32), Dst: 172.21.35.5 (00:11:25:a8:75:7e)

    Address Resolution Protocol (request)

    N ° time Source Destination Protocol Info

    3 1.381842 172.21.35.5 172.21.35.2 ARP 172.21.35.5 is to 00:11:25:a8:75:7e

    Frame 3 (42 bytes on wire, 42 captured bytes)

    Ethernet II, Src: 172.21.35.5 (00:11:25:a8:75:7e), Dst: 172.21.35.2 (00: 0d: 60:ec:85:32)

    Address Resolution Protocol (reply)

    N ° time Source Destination Protocol Info

    4 2.754731 172.21.35.5 broadcast ARP which has 172.21.35.4? Say 172.21.35.5

    Frame 4 (42 bytes on wire, 42 captured bytes)

    Ethernet II, Src: 172.21.35.5 (00:11:25:a8:75:7e), Dst: Broadcast (ff: ff: ff: ff: ff: ff)

    Address Resolution Protocol (request)

    N ° time Source Destination Protocol Info

    5 2.754839 172.21.35.4 172.21.35.5 ARP 172.21.35.4 is to 00:11:25:57:f9:2 c

    Frame 5 (106 bytes on wire, 106 captured bytes)

    Ethernet II, Src: 172.21.35.4 (00:11:25:57:f9:2 c), Dst: 172.21.35.5 (00:11:25:a8:75:7e)

    Address Resolution Protocol (reply)

    N ° time Source Destination Protocol Info

    6 2.754968 172.21.35.1 172.21.35.5 ARP 172.21.35.4 is at 00: 0d: 88:ef:23:29

    Image 6 (60 bytes on wire, 60 bytes captured)

    Ethernet II, Src: 172.21.35.1 (00: 0d: 88:ef:23:29), Dst: 172.21.35.5 (00:11:25:a8:75:7e)

    Address Resolution Protocol (reply)

    on the pix

    #debug arp

    782: arp-in: application to the demilitarized zone of 172.21.35.4 0011.2557.f92c for 172.21.35.1 0000.0000.0000

    783: arp - set: arp added dmz 172.21.35.4 0011.2557.f92c

    784: arp-in: generate the response of 172.21.35.1 000d.88ef.2329 to 172.21.35.4 0011.2557.f92c

    793: arp-in: application to the demilitarized zone of 172.21.35.5 0011.25a8.757e for 172.21.35.4 0000.0000.0000

    794: arp - set: arp added dmz 172.21.35.5 0011.25a8.757e

    795: arp-in: generate the response of 172.21.35.4 000d.88ef.2329 to 172.21.35.5 0011.25a8.757e

    Why pix sends the response to the arp request?

    Hello

    Maybe it's because proxy ARP on the pix. You can try disabling this interface with the command "sysopt noproxyarp.

  • Unidentified network Windows 8 Pro

    Hello

    I have a Windows 8 Pro 64 bit computer bit and it said that my wifi internet connection is "not identified-no network access.
    I have a WiFi hotspot and it works on the PC of my father and my Android tablet. (by the way, the hotspot is a public network with a p/sem.)
    I tried:

    Restart the PC and the router,

    Windows Troubleshooting (poster "WiFi is not a valid IP configuration")

    Have turned off Windows Firewall (witch worked for 10 minutes) and I uninstalled Quicktime & Hello,.

    I have no strange services that run in the background in taskmanager

    Unchecked TCP/IPv6

    Turn off/on WiFi adapter

    Uninstall the driver for the WiFi card.

    Deleted ROUTE 0.0.0.0

    'Forget' the network

    Re-installation of IPv4 & Ipv6

    I ran as administrator of these commands

    Restore the default install WINSOCK entries: netsh winsock reset catalog

    Reset the battery TCP/IP IPv4 default installation. netsh int ipv4 reset reset.log

    Reset the battery TCP/IP IPv6 default installation. netsh int ipv6 reset reset.log

    netsh int ip reset C:\netsh.log.txt
    netsh winsock reset

    All do not work. I noticed a strange thing. In the properties of the wireless adapter TCP/IPv6 & TCP/Ipv4 have "Uninstall" whited.

    I tried to reinstall them but that has not worked.

    The last program that I installed is Adobe Download Assistant (I uninstalled, did not work)

    And the last update of Windows installed is a "critical update for Windows 8. But he did not set a restore point before installation.

    Any help would be appreciated.

    Josh

    PS: I contacted my internet provider and they said: 'this isn't our fault, contact the manufacturer of your PC. I did, but he couldn't understand our either.

    Josh,

    There is an APIPA address assigned automatically to the adapter wireless and as a result of which you cannot join any network or Internet access.

    APIPA - an automatic private IP addressing

    Addressing IP private AUTO is a DHCP (Dynamic Host Configuration protocol) failover mechanism for local area networks. With AUTOMATIC private IP addressing, DHCP clients can obtain IP addresses, when the DHCP servers are non-functional. AUTOMATIC private IP addressing is in all modern versions of Windows.

    When the failure of a DHCP, APIPA server allocates IP addresses in the private range 169.254.0.1 to 169.254.255.254. Customers ensure that their address is unique on the network using ARP (Address resolution Protocol). When the DHCP server is again capable of service requests, clients automatically update their addresses.

    APIPA, all devices using the default netmask 255.255.0.0 and all reside on the same

    I would have you try these commands once more.

    netsh int ip reset resetlog.txt
    netsh winsock reset
    ipconfig/registerdns
    ipconfig/flushdns
    ipconfig/release

    Restart the computer, and then check if you are able to connect to the network.

    If the problem persists, manually assign an IP address to the wireless network and then try to ping the router to check if there is a good connection.

    -Press the Windows key and the R key and then type NCPA. CPL

    -Right click on the wireless network you are using, and then select Properties.

    -Highlight or select version 4 Internet Protocol and click Properties.

    -Select the option use the following IP address.

    If the IP address of the router is 192.168.1.1, and the other the computer IP address is in the same sequence 192.168.1.2, then try to assign 192.168.1.3 and mass subnet 255.255.255.0 and press ENTER.

    -Close the network properties window.

    -Open the command prompt and type ping 127.0.0.1 and press ENTER.

    -Type ping 192.168.1.1 and press on enter

    -Type ping 192.168.1.3 and press to enter.

    Let us know if the packets sent are equal to the packets received.

    Post a screenshot after doing so.

  • OSPF in DLR Protocol address

    When configuring OSPF in DLR configure us the address and Protocol addresses.

    This IP address is the same as the address of the DLR VM control management.

    Protocol address: 192.168.10.3. This address is assigned to DLR control VM vNIC.

    But you have not shown where it has been configured. It is automatically assigned in the DLR VM control or you configure this address manually in control VM.

    Answer: In the user interface when you configure this address it automatically send to DLR control VM and the ESXi running of the DLR

    during the configuration of interfaces in DLR you must first configure address management for VM control.

    Answer: you don't have to configure an ip address any management, that's what I'm trying to explain in my first message, the perfect DLR work without any management ip address.

    My question was is this address mgmt control VM as a protocol address

    Answer: No, if you have decided to put the management ip address, you have different ip address of the transmission or the Protocol address.

  • Error: Ship to / Bill to address is invalid. Please check the configuration of the address

    After the upgrade to 12.1.3, commands fail during the import/Scheduling with "error: ship to / Bill to address is invalid.". Please check the configuration of the address"every time the tax engine is called. And this is the case for only specific addresses (which are valid). I'd appreciate any suggestion/experience on this topic.

    Thank you
    Mariefrance

    Hello

    There were multiple causes for the same problem, namely:
    (1) no valid address according to the Vertex - resolution here would be to find the name of the alias of the city for the Zip code (Google, zip - codes.com, etc.) and use it. You should see the result immediately.

    (2) Texas or Forida addresses where there is no link - often we see that there are multiple records in vertex for the city, and it generates an error. Here the safest option is to perform the encryption of the geography of vertices for these combinations and then update the same in Oracle as the substitution of GeographyCode (default value = "77000000") to remove vertex call. Alternatively, we can create a type AR Txn with the Classification of taxes as 'No' and then linking to a new order Type. Any order with this type of order will not call vertex.

    (3) military addresses - resolution is the same as 2 above.

    Mariefrance

  • PC accessed remotely by hackers, all certificates, keys, authorizations, for my PC and my identity were copied and stolen. Several online accounts had been accessed by a third party.

    Online remote access to my PC and my credentials and personal information were stolen. I had several compromised online accounts. I had Windows Live using their remote access three times service and my computer is always connected remotely. I'm stuck using many admin capabilities. The task manager says there is more than one user, but I'm the only visible.  Name resolution Protocol, Peer Networking peer Peer Networking Identity Manager, Remote Procedure Call, Mapper by point final CPP, Windows connect now Config clerk, are among the many active services right now. Resource monitor shows me connected to a remote network, there are other IPS listed other than mine. I found a hidden desk top, with map of the network... including an android phone, a Tablet PC Input Panel with a foreign alphabet. There are many programs, I've never added to my PC. I find the hidden devices that are listed as part of a network, they do not belong to my PC. My modem has no Wy - Fy, or my router. I removed the ethernet cables... the power cord, monitor, keyboard and mouse. My modem has been disconnected from the external source and the router, but was still connected and powered on, all the lights were not on showing no connection. Very shortly, I saw the indicatator of DSL connection will begin to Flash. I unplugged the modem. A minute later, I heard the ping and the squeal to initialize an internet connection from my flat satellite receiver. When I checked my PC, he was very quietly running in stealth mode, apparently fleeing electricity drawn from the speakers I left wired. I'm sure you can tell just by reading that I don't know much about computers. This situation has worried me. Microsoft said that they fixed access points and it was clean from the virus and malware. Apparently it is not. I ask to change my IP address or security credentials, regardless of which is used to verify my identity, my question is did not answer, leaving unresolved.  I am very concerned because all certificates of proof of identity online, IPaddress, Signatures etc., were copied and stolen.  The hackers have the opportunity to make me look at will and have used it to seep into my GMAIL, FACEBOOK and some other accounts. I am at a loss. I will contact Microsoft Live again... I paid cover me 30 days it wil expire on 5 December. I guess that my cyber identity has been stolen. Is it me as a victim of identity theft? Should the technicians who worked on my computer could solve my problem to be hacked and stolen ID. I made a police report a few weeks, I was told it wasn't a crime unless I could prove identity theft, that was before I had no Service. Contact the FBI. Any help or advice or anything at all that you can provide would be greatly appreciated. I don't know which forum to post in both, if I choose wrong... Please help to direct my concerns to where it can be treated... Thank you a lot =)

    The first thing you need to do is change ALL your passwords on all accounts - using a known machine - cleaning - and NOT connect to them with a mchine to which you think is infected.

    Then only you should undertake the cleaning of the machine.

  • EASY CONNECT STOPPED WORKING

    I clicked on ' nearby remote assistance and resolve problems "and he says:

    Problems found

    Your computer seems to be configured correctly, but the device or resource (Server NVRP) does not

    The PNRP cloud specified could not start correctly the server: prnpv2.ipv6.microsoft.com; pnrpv21.ipv6.microsoft.com

    I don't know what all this means.

    It stopped working before... I installed McAfee and after a bit of reading on the internet, I got rid of McAfee and Easy Connect reworked.

    Now I just use Windows Defender and Windows Firewall and have not installed anything new with the exception of Windows updates.

    Thanks for your suggestions.

    Additional wire duplicate content:

    EASY CONNECT STOPPED WORKING

    I clicked on ' nearby remote assistance and resolve problems "and he says:

    Problems found

    Your computer seems to be configured correctly, but the device or resource (Server NVRP) does not

    The PNRP cloud specified could not start correctly the server: prnpv2.ipv6.microsoft.com; pnrpv21.ipv6.microsoft.com

    I don't know what all this means.

    I just used Windows Defender and Windows Firewall and have not installed anything new with the exception of Windows updates.

    I tried troubleshooting network and the internet and the problem persists.

    I looked at what follows, and they did not help to get Easy Connect works again.

    http://Windows.Microsoft.com/en-us/Windows7/why-cant-I-use-easy-connect-with-Windows-remote-assistance

    http://Windows.Microsoft.com/en-in/Windows/Windows-remote-assistance-FAQ#1TC=Windows-8

    Hi compounded,

    Thanks for posting on Microsoft Community.

    I appreciate your efforts to try to solve this problem.

    I'm sorry to know that Easy Connect does not work and it seems that there is a problem with the connection to the peer name resolution server.

    In peer-to-peer environments, peers are based on name resolution systems to resolve each and other locations (addresses, protocols, and ports) from names or other types of identifiers network. Peer-to-peer name resolution has been complicated by transient connectivity and shortcomings in the domain name system (DNS).

    Peer-to-Peer networking platform solves this problem with the PNRP Peer Name Resolution Protocol (), a secure, scalable, and dynamic name registration.

    This question might be the best answer by TechNet. Then I suggest you send the request on the TechNet forums.

    https://social.technet.Microsoft.com/forums/Windows/en-us/home?category=w7itpro

    In the future, if you have problems with Windows. Not to contact us. We will be happy to help you.

  • Cisco ASA 5505 VPN Site to Site

    Hi all

    First post on the forums. I have worked with Cisco ASA 5505 for a few months and I recently bought a 2nd ASA to implement tunnel VPN Site to Site. It seems so simple in the number of videos watched on the internet. But when I did he surprise it did work for me... I've removed the tunnels, a number of times and tried to recreate. I use the VPN Wizard in the SMA to create the tunnel. Both the asa 5505 of are and have the same firmware even etc..

    I'd appreciate any help that can be directed to this problem please.  Slowly losing my mind

    Please see details below:

    Two ADMS are 7.1

    IOS

    ASA 1

    Nadia

    :

    ASA Version 9.0 (1)

    !

    hostname PAYBACK

    activate the encrypted password of HSMurh79NVmatjY0

    volatile xlate deny tcp any4 any4

    volatile xlate deny tcp any4 any6

    volatile xlate deny tcp any6 any4

    volatile xlate deny tcp any6 any6

    volatile xlate deny udp any4 any4 eq field

    volatile xlate deny udp any4 any6 eq field

    volatile xlate deny udp any6 any4 eq field

    volatile xlate deny udp any6 any6 eq field

    2KFQnbNIdI.2KYOU encrypted passwd

    names of

    local pool VPN1 192.168.50.1 - 192.168.50.254 255.255.255.0 IP mask

    !

    interface Ethernet0/0

    switchport access vlan 2

    Speed 100

    full duplex

    !

    interface Ethernet0/1

    link Trunk Description of SW1

    switchport trunk allowed vlan 1,10,20,30,40

    switchport trunk vlan 1 native

    switchport mode trunk

    !

    interface Ethernet0/2

    !

    interface Ethernet0/3

    !

    interface Ethernet0/4

    !

    interface Ethernet0/5

    !

    interface Ethernet0/6

    !

    interface Ethernet0/7

    !

    interface Vlan1

    No nameif

    no level of security

    no ip address

    !

    interface Vlan2

    nameif outside

    security-level 0

    IP 92.51.193.158 255.255.255.252

    !

    interface Vlan10

    nameif inside

    security-level 100

    IP 192.168.10.1 255.255.255.0

    !

    interface Vlan20

    nameif servers

    security-level 100

    address 192.168.20.1 255.255.255.0

    !

    Vlan30 interface

    nameif printers

    security-level 100

    192.168.30.1 IP address 255.255.255.0

    !

    interface Vlan40

    nameif wireless

    security-level 100

    192.168.40.1 IP address 255.255.255.0

    !

    connection line banner welcome to the Payback loyalty systems

    boot system Disk0: / asa901 - k8.bin

    passive FTP mode

    summer time clock GMT/IDT recurring last Sun Mar 01:00 last Sun Oct 02:00

    DNS domain-lookup outside

    DNS lookup field inside

    domain-lookup DNS servers

    DNS lookup domain printers

    DNS domain-lookup wireless

    DNS server-group DefaultDNS

    Server name 83.147.160.2

    Server name 83.147.160.130

    permit same-security-traffic inter-interface

    network obj_any object

    subnet 0.0.0.0 0.0.0.0

    ftp_server network object

    network of the Internal_Report_Server object

    Home 192.168.20.21

    Description address internal automated report server

    network of the Report_Server object

    Home 89.234.126.9

    Description of server automated reports

    service object RDP

    service destination tcp 3389 eq

    Description RDP to the server

    network of the Host_QA_Server object

    Home 89.234.126.10

    Description QA host external address

    network of the Internal_Host_QA object

    Home 192.168.20.22

    host of computer virtual Description for QA

    network of the Internal_QA_Web_Server object

    Home 192.168.20.23

    Description Web Server in the QA environment

    network of the Web_Server_QA_VM object

    Home 89.234.126.11

    Server Web Description in the QA environment

    service object SQL_Server

    destination eq 1433 tcp service

    network of the Demo_Server object

    Home 89.234.126.12

    Description server set up for the product demo

    network of the Internal_Demo_Server object

    Home 192.168.20.24

    Internal description of the demo server IP address

    network of the NETWORK_OBJ_192.168.20.0_24 object

    subnet 192.168.20.0 255.255.255.0

    network of the NETWORK_OBJ_192.168.50.0_26 object

    255.255.255.192 subnet 192.168.50.0

    network of the NETWORK_OBJ_192.168.0.0_16 object

    Subnet 192.168.0.0 255.255.0.0

    service object MSSQL

    destination eq 1434 tcp service

    MSSQL port description

    VPN network object

    192.168.50.0 subnet 255.255.255.0

    network of the NETWORK_OBJ_192.168.50.0_24 object

    192.168.50.0 subnet 255.255.255.0

    service object TS

    tcp destination eq 4400 service

    service of the TS_Return object

    tcp source eq 4400 service

    network of the External_QA_3 object

    Home 89.234.126.13

    network of the Internal_QA_3 object

    Home 192.168.20.25

    network of the Dev_WebServer object

    Home 192.168.20.27

    network of the External_Dev_Web object

    Home 89.234.126.14

    network of the CIX_Subnet object

    255.255.255.0 subnet 192.168.100.0

    network of the NETWORK_OBJ_192.168.10.0_24 object

    192.168.10.0 subnet 255.255.255.0

    network of the NETWORK_OBJ_84.39.233.50 object

    Home 84.39.233.50

    network of the NETWORK_OBJ_92.51.193.158 object

    Home 92.51.193.158

    network of the NETWORK_OBJ_192.168.100.0_24 object

    255.255.255.0 subnet 192.168.100.0

    network of the NETWORK_OBJ_192.168.1.0_24 object

    subnet 192.168.1.0 255.255.255.0

    object-group service DM_INLINE_SERVICE_1

    the tcp destination eq ftp service object

    the purpose of the tcp destination eq netbios-ssn service

    the purpose of the tcp destination eq smtp service

    service-object TS

    the Payback_Internal object-group network

    object-network 192.168.10.0 255.255.255.0

    object-network 192.168.20.0 255.255.255.0

    object-network 192.168.40.0 255.255.255.0

    object-group service DM_INLINE_SERVICE_3

    the purpose of the service tcp destination eq www

    the purpose of the tcp destination eq https service

    service-object TS

    service-object, object TS_Return

    object-group service DM_INLINE_SERVICE_4

    service-object RDP

    the purpose of the service tcp destination eq www

    the purpose of the tcp destination eq https service

    object-group service DM_INLINE_SERVICE_5

    purpose purpose of the MSSQL service

    service-object RDP

    service-object TS

    object-group Protocol TCPUDP

    object-protocol udp

    object-tcp protocol

    object-group service DM_INLINE_SERVICE_6

    service-object TS

    service-object, object TS_Return

    the purpose of the service tcp destination eq www

    the purpose of the tcp destination eq https service

    Note to outside_access_in to access list that this rule allows Internet the interal server.

    Notice on the outside_access_in of the access-list allowed:

    Comment from outside_access_in-list of FTP access

    Comment from outside_access_in-RDP access list

    Comment from outside_access_in-list of SMTP access

    Note to outside_access_in to access list Net Bios

    Comment from outside_access_in-SQL access list

    Comment from outside_access_in-list to access TS - 4400

    outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_1 any4 Internal_Report_Server

    access host access-list outside_access_in note rule internal QA

    Notice on the outside_access_in of the access-list allowed:

    Comment from outside_access_in-HTTP access list

    Comment from outside_access_in-RDP access list

    outside_access_in list extended access permitted tcp any4 object Internal_Host_QA eq www

    Notice on the outside_access_in of the access-list access to the internal Web server:

    Notice on the outside_access_in of the access-list allowed:

    Comment from outside_access_in-HTTP access list

    Comment from outside_access_in-RDP access list

    outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_3 any4 Internal_QA_Web_Server

    Note to outside_access_in to access list rule allowing access to the demo server

    Notice on the outside_access_in of the access-list allowed:

    Comment from outside_access_in-RDP access list

    Comment from outside_access_in-list to access MSSQL

    outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_4 any4 Internal_Demo_Server

    outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_5 any object Internal_QA_3

    Note to outside_access_in access to the development Web server access list

    outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_6 any object Dev_WebServer

    AnyConnect_Client_Local_Print deny any4 any4 ip extended access list

    AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq lpd

    Note AnyConnect_Client_Local_Print of access list IPP: Internet Printing Protocol

    AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq 631

    print the access-list AnyConnect_Client_Local_Print Note Windows port

    AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq 9100

    access-list AnyConnect_Client_Local_Print mDNS Note: multicast DNS protocol

    AnyConnect_Client_Local_Print list extended access permit udp host 224.0.0.251 any4 eq 5353

    AnyConnect_Client_Local_Print of access list LLMNR Note: link Local Multicast Name Resolution protocol

    AnyConnect_Client_Local_Print list extended access permit udp host 224.0.0.252 any4 eq 5355

    Note access list TCP/NetBIOS protocol AnyConnect_Client_Local_Print

    AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 EQ. 137

    AnyConnect_Client_Local_Print list extended access permitted udp any4 any4 eq netbios-ns

    Payback_VPN_splitTunnelAcl list standard access allowed 192.168.20.0 255.255.255.0

    permit outside_cryptomap to access extended list ip 192.168.10.0 255.255.255.0 192.168.100.0 255.255.255.0

    pager lines 24

    Enable logging

    information recording console

    asdm of logging of information

    address record

    [email protected] / * /.

    the journaling recipient

    [email protected] / * /.

    level alerts

    Outside 1500 MTU

    Within 1500 MTU

    MTU 1500 servers

    MTU 1500 printers

    MTU 1500 wireless

    no failover

    ICMP unreachable rate-limit 1 burst-size 1

    ASDM image disk0: / asdm-711 - 52.bin

    don't allow no asdm history

    ARP timeout 14400

    no permit-nonconnected arp

    NAT (inside, outside) source Dynamics one interface

    NAT (wireless, outdoors) source Dynamics one interface

    NAT (servers, outside) no matter what source dynamic interface

    NAT (servers, external) static source Internal_Report_Server Report_Server

    NAT (servers, external) static source Internal_Host_QA Host_QA_Server

    NAT (servers, external) static source Internal_QA_Web_Server Web_Server_QA_VM

    NAT (servers, external) static source Internal_Demo_Server Demo_Server

    NAT (servers, external) static source NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.50.0_24 NETWORK_OBJ_192.168.50.0_24 non-proxy-arp-search of route static destination

    NAT (servers, external) static source Internal_QA_3 External_QA_3

    NAT (servers, external) static source Dev_WebServer External_Dev_Web

    NAT (inside, outside) static source NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination

    NAT (inside, outside) static source NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 non-proxy-arp-search of route static destination

    Access-group outside_access_in in interface outside

    Route outside 0.0.0.0 0.0.0.0 92.51.193.157 1

    Timeout xlate 03:00

    Pat-xlate timeout 0:00:30

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    timeout tcp-proxy-reassembly 0:01:00

    Floating conn timeout 0:00:00

    dynamic-access-policy-registration DfltAccessPolicy

    identity of the user by default-domain LOCAL
    the ssh LOCAL console AAA authentication
    Enable http server
    http 192.168.10.0 255.255.255.0 inside
    http 192.168.40.0 255.255.255.0 wireless
    No snmp server location
    No snmp Server contact
    Server enable SNMP traps snmp authentication linkup, linkdown cold start
    Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
    Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
    Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
    Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
    Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
    Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
    Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
    Crypto ipsec ikev2 AES256 ipsec-proposal
    Protocol esp encryption aes-256
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 ipsec-proposal AES192
    Protocol esp encryption aes-192
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 ipsec-proposal AES
    Esp aes encryption protocol
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 proposal ipsec 3DES
    Esp 3des encryption protocol
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 ipsec-proposal OF
    encryption protocol esp
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec pmtu aging infinite - the security association
    card crypto outside_map 1 match address outside_cryptomap
    card crypto outside_map 1 set pfs
    peer set card crypto outside_map 1 84.39.233.50
    card crypto outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
    outside_map card crypto 1 set ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
    outside_map interface card crypto outside
    trustpool crypto ca policy
    IKEv2 crypto policy 1
    aes-256 encryption
    integrity sha
    Group 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 10
    aes-192 encryption
    integrity sha
    Group 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 20
    aes encryption
    integrity sha
    Group 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 30
    3des encryption
    integrity sha
    Group 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 40
    the Encryption
    integrity sha
    Group 5
    FRP sha
    second life 86400
    Crypto ikev2 activate out of service the customer port 443
    Crypto ikev1 allow outside
    IKEv1 crypto policy 10
    preshared authentication
    3des encryption
    sha hash
    Group 2
    life 86400
    Telnet timeout 5
    SSH 77.75.100.208 255.255.255.240 outside
    SSH 192.168.10.0 255.255.255.0 inside
    SSH 192.168.40.0 255.255.255.0 wireless
    SSH timeout 5
    Console timeout 0

    dhcpd 192.168.0.1 dns
    dhcpd outside auto_config
    !
    dhcpd address 192.168.10.21 - 192.168.10.240 inside
    dhcpd dns 192.168.20.21 83.147.160.2 interface inside
    paybackloyalty.com dhcpd option 15 inside ascii interface
    dhcpd allow inside
    !
    dhcpd address 192.168.40.21 - 192.168.40.240 Wireless
    dhcpd dns 192.168.20.21 83.147.160.2 wireless interface
    dhcpd update dns of the wireless interface
    dhcpd option 15 ascii paybackloyalty.com wireless interface
    dhcpd activate wireless
    !
    a basic threat threat detection
    Statistics-list of access threat detection
    no statistical threat detection tcp-interception
    internal Payback_VPN group strategy
    attributes of Group Policy Payback_VPN
    VPN - 10 concurrent connections
    Ikev1 VPN-tunnel-Protocol
    Split-tunnel-policy tunnelspecified
    value of Split-tunnel-network-list Payback_VPN_splitTunnelAcl
    attributes of Group Policy DfltGrpPolicy
    value of 83.147.160.2 DNS server 83.147.160.130
    VPN-tunnel-Protocol ikev1, ikev2 clientless ssl
    internal GroupPolicy_84.39.233.50 group strategy
    attributes of Group Policy GroupPolicy_84.39.233.50
    VPN-tunnel-Protocol ikev1, ikev2
    Noelle XB/IpvYaATP.2QYm username encrypted password
    Noelle username attributes
    VPN-group-policy Payback_VPN
    type of remote access service
    username Éanna encrypted password privilege 0 vXILR9ZZQIsd1Naw
    Éanna attributes username
    VPN-group-policy Payback_VPN
    type of remote access service
    Michael qpbleUqUEchRrgQX of encrypted password username
    user name Michael attributes
    VPN-group-policy Payback_VPN
    type of remote access service
    username, password from Danny .7fEXdzESUk6S/cC encrypted privilege 0
    user name Danny attributes
    VPN-group-policy Payback_VPN
    type of remote access service
    Aileen tytrelqvV5VRX2pz encrypted password privilege 0 username
    user name Aileen attributes
    VPN-group-policy Payback_VPN
    type of remote access service
    Aidan aDu6YH0V5XaxpEPg encrypted password privilege 0 username
    Aidan username attributes
    VPN-group-policy Payback_VPN
    type of remote access service
    username password 6e6Djaz3W/XH59zX gordon encrypted privilege 15
    shane.c iqGMoWOnfO6YKXbw encrypted password username
    username shane.c attributes
    VPN-group-policy Payback_VPN
    type of remote access service
    Shane uYePLcrFadO9pBZx of encrypted password username
    user name Shane attributes
    VPN-group-policy Payback_VPN
    type of remote access service
    username, encrypted James TdYPv1pvld/hPM0d password
    user name James attributes
    VPN-group-policy Payback_VPN
    type of remote access service
    Mark yruxpddqfyNb.qFn of encrypted password username
    user name brand attributes
    type of service admin
    username password of Mary XND5FTEiyu1L1zFD encrypted
    user name Mary attributes
    VPN-group-policy Payback_VPN
    type of remote access service
    Massimo vs65MMo4rM0l4rVu encrypted password privilege 0 username
    Massimo username attributes
    VPN-group-policy Payback_VPN
    type of remote access service
    type tunnel-group Payback_VPN remote access
    attributes global-tunnel-group Payback_VPN
    VPN1 address pool
    Group Policy - by default-Payback_VPN
    IPSec-attributes tunnel-group Payback_VPN
    IKEv1 pre-shared-key *.
    tunnel-group 84.39.233.50 type ipsec-l2l
    tunnel-group 84.39.233.50 General-attributes
    Group - default policy - GroupPolicy_84.39.233.50
    IPSec-attributes tunnel-group 84.39.233.50
    IKEv1 pre-shared-key *.
    remote control-IKEv2 pre-shared-key authentication *.
    pre-shared-key authentication local IKEv2 *.
    !
    Global class-card class
    match default-inspection-traffic
    !
    !
    World-Policy policy-map
    Global category
    inspect the dns
    inspect the ftp
    inspect h323 h225
    inspect the h323 ras
    Review the ip options
    inspect the netbios
    inspect the pptp
    inspect the rsh
    inspect the rtsp
    inspect the sip
    inspect the snmp
    inspect sqlnet
    inspect sunrpc
    inspect the tftp
    inspect xdmcp
    inspect the icmp error
    inspect the icmp
    !
    service-policy-international policy global
    192.168.20.21 SMTP server
    context of prompt hostname
    no remote anonymous reporting call
    call-home
    Profile of CiscoTAC-1
    no active account
    http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
    email address of destination [email protected] / * /
    destination-mode http transport
    Subscribe to alert-group diagnosis
    Subscribe to alert-group environment
    Subscribe to alert-group monthly periodic inventory
    monthly periodicals to subscribe to alert-group configuration
    daily periodic subscribe to alert-group telemetry
    Cryptochecksum:d06974501eb0327a5ed229c8445f4fe1

    ASA 2

    ASA Version 9.0 (1)

    !

    Payback-CIX hostname

    activate the encrypted password of HSMurh79NVmatjY0

    2KFQnbNIdI.2KYOU encrypted passwd

    names of

    !

    interface Ethernet0/0

    switchport access vlan 2

    Speed 100

    full duplex

    !

    interface Ethernet0/1

    Description this port connects to the local network VIRTUAL 100

    switchport access vlan 100

    !

    interface Ethernet0/2

    !

    interface Ethernet0/3

    switchport access vlan 100

    !

    interface Ethernet0/4

    switchport access vlan 100

    !

    interface Ethernet0/5

    switchport access vlan 100

    !

    interface Ethernet0/6

    switchport access vlan 100

    !

    interface Ethernet0/7

    switchport access vlan 100

    !

    interface Vlan2

    nameif outside

    security-level 0

    IP 84.39.233.50 255.255.255.240

    !

    interface Vlan100

    nameif inside

    security-level 100

    IP 192.168.100.1 address 255.255.255.0

    !

    banner welcome to Payback loyalty - CIX connection line

    passive FTP mode

    summer time clock gmt/idt recurring last Sun Mar 01:00 last Sun Oct 02:00

    DNS domain-lookup outside

    DNS lookup field inside

    DNS server-group defaultDNS

    Name-Server 8.8.8.8

    Server name 8.8.4.4

    permit same-security-traffic inter-interface

    network obj_any object

    subnet 0.0.0.0 0.0.0.0

    network of the host-CIX-1 object

    host 192.168.100.2

    Description This is the VM server host machine

    network object host-External_CIX-1

    Home 84.39.233.51

    Description This is the external IP address of the server the server VM host

    service object RDP

    source between 1-65535 destination eq 3389 tcp service

    network of the Payback_Office object

    Home 92.51.193.158

    service object MSQL

    destination eq 1433 tcp service

    network of the Development_OLTP object

    Home 192.168.100.10

    Description for Eiresoft VM

    network of the External_Development_OLTP object

    Home 84.39.233.52

    Description This is the external IP address for the virtual machine for Eiresoft

    network of the Eiresoft object

    Home 146.66.160.70

    Contractor s/n description

    network of the External_TMC_Web object

    Home 84.39.233.53

    Description Public address to the TMC Web server

    network of the TMC_Webserver object

    Home 192.168.100.19

    Internal description address TMC Webserver

    network of the External_TMC_OLTP object

    Home 84.39.233.54

    External targets OLTP IP description

    network of the TMC_OLTP object

    Home 192.168.100.18

    description of the interal target IP address

    network of the External_OLTP_Failover object

    Home 84.39.233.55

    IP failover of the OLTP Public description

    network of the OLTP_Failover object

    Home 192.168.100.60

    Server failover OLTP description

    network of the servers object

    subnet 192.168.20.0 255.255.255.0

    being Wired network

    192.168.10.0 subnet 255.255.255.0

    the subject wireless network

    192.168.40.0 subnet 255.255.255.0

    network of the NETWORK_OBJ_192.168.100.0_24 object

    255.255.255.0 subnet 192.168.100.0

    network of the NETWORK_OBJ_192.168.10.0_24 object

    192.168.10.0 subnet 255.255.255.0

    network of the Eiresoft_2nd object

    Home 137.117.217.29

    Description 2nd Eiresoft IP

    network of the Dev_Test_Webserver object

    Home 192.168.100.12

    Description address internal to the Test Server Web Dev

    network of the External_Dev_Test_Webserver object

    Home 84.39.233.56

    Description This is the PB Dev Test Webserver

    network of the NETWORK_OBJ_192.168.1.0_24 object

    subnet 192.168.1.0 255.255.255.0

    object-group service DM_INLINE_SERVICE_1

    service-object MSQL

    service-object RDP

    object-group service DM_INLINE_SERVICE_2

    service-object MSQL

    service-object RDP

    object-group service DM_INLINE_SERVICE_3

    service-object MSQL

    service-object RDP

    object-group service DM_INLINE_SERVICE_4

    service-object MSQL

    service-object RDP

    the tcp destination eq ftp service object

    object-group service DM_INLINE_SERVICE_5

    service-object MSQL

    service-object RDP

    the tcp destination eq ftp service object

    object-group service DM_INLINE_SERVICE_6

    service-object MSQL

    service-object RDP

    the Payback_Intrernal object-group network

    object-network servers

    Wired network-object

    wireless network object

    object-group service DM_INLINE_SERVICE_7

    service-object MSQL

    service-object RDP

    object-group service DM_INLINE_SERVICE_8

    service-object MSQL

    service-object RDP

    object-group service DM_INLINE_SERVICE_9

    service-object MSQL

    service-object RDP

    object-group service DM_INLINE_SERVICE_10

    service-object MSQL

    service-object RDP

    the tcp destination eq ftp service object

    object-group service DM_INLINE_SERVICE_11

    service-object RDP

    the tcp destination eq ftp service object

    outside_access_in list extended access allow object-group DM_INLINE_SERVICE_1 object Payback_Office object CIX-host-1

    Note to access list OLTP Development Office of recovery outside_access_in

    outside_access_in list extended access allow DM_INLINE_SERVICE_2 object Payback_Office object Development_OLTP object-group

    Comment from outside_access_in-access Eiresoft access list

    outside_access_in list extended access allow DM_INLINE_SERVICE_3 object Eiresoft object Development_OLTP object-group

    outside_access_in list extended access allow DM_INLINE_SERVICE_4 object Payback_Office object TMC_Webserver object-group

    Note to outside_access_in access to OLTP for target recovery Office Access list

    outside_access_in list extended access allow DM_INLINE_SERVICE_5 object Payback_Office object TMC_OLTP object-group

    outside_access_in list extended access allow DM_INLINE_SERVICE_6 object Payback_Office object OLTP_Failover object-group

    Note to outside_access_in access-list that's allowing access of the Eiresoft on the failover OLTP server

    outside_access_in list extended access allow DM_INLINE_SERVICE_7 object Eiresoft object OLTP_Failover object-group

    Comment from outside_access_in-access list access for the 2nd period of INVESTIGATION of Eiresoft

    outside_access_in list extended access allow DM_INLINE_SERVICE_8 object Eiresoft_2nd object Development_OLTP object-group

    Note to outside_access_in access from the 2nd IP Eiresoft access list

    outside_access_in list extended access allow DM_INLINE_SERVICE_9 object Eiresoft_2nd object OLTP_Failover object-group

    outside_access_in list extended access allow DM_INLINE_SERVICE_10 object Payback_Office object Dev_Test_Webserver object-group

    outside_access_in list extended access allow DM_INLINE_SERVICE_11 object Payback_Office object External_TMC_OLTP object-group

    outside_cryptomap to access extended list ip 192.168.100.0 allow 255.255.255.0 192.168.10.0 255.255.255.0

    pager lines 24

    Enable logging

    asdm of logging of information

    Outside 1500 MTU

    Within 1500 MTU

    ICMP unreachable rate-limit 1 burst-size 1

    don't allow no asdm history

    ARP timeout 14400

    no permit-nonconnected arp

    NAT (inside, outside) source Dynamics one interface

    NAT (inside, outside) static source CIX-host-1 External_CIX-host-1

    NAT (inside, outside) static source Development_OLTP External_Development_OLTP

    NAT (inside, outside) static source TMC_Webserver External_TMC_Web

    NAT (inside, outside) static source TMC_OLTP External_TMC_OLTP

    NAT (inside, outside) static source OLTP_Failover External_OLTP_Failover

    NAT (inside, outside) static source Dev_Test_Webserver External_Dev_Test_Webserver

    NAT (inside, outside) static source NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 non-proxy-arp-search of route static destination

    NAT (inside, outside) static source NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination

    Access-group outside_access_in in interface outside

    Route outside 0.0.0.0 0.0.0.0 84.39.233.49 1

    Timeout xlate 03:00

    Pat-xlate timeout 0:00:30

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    timeout tcp-proxy-reassembly 0:01:00

    Floating conn timeout 0:00:00

    dynamic-access-policy-registration DfltAccessPolicy

    identity of the user by default-domain LOCAL

    the ssh LOCAL console AAA authentication

    Enable http server

    http 92.51.193.156 255.255.255.252 outside

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

    Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac

    Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit

    Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac

    Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit

    Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac

    Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit

    Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac

    Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit

    Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac

    Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit

    Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac

    Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit

    Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac

    Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit

    Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac

    Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit

    Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

    Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac

    Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit

    Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac

    Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit

    Crypto ipsec ikev2 ipsec-proposal OF

    encryption protocol esp
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 proposal ipsec 3DES
    Esp 3des encryption protocol
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 ipsec-proposal AES
    Esp aes encryption protocol
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 ipsec-proposal AES192
    Protocol esp encryption aes-192
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec ikev2 AES256 ipsec-proposal
    Protocol esp encryption aes-256
    Esp integrity sha - 1, md5 Protocol
    Crypto ipsec pmtu aging infinite - the security association
    card crypto outside_map 1 match address outside_cryptomap
    card crypto outside_map 1 set pfs
    peer set card crypto outside_map 1 92.51.193.158
    card crypto outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
    outside_map card crypto 1jeu ikev2 AES AES192 AES256 3DES ipsec-proposal
    outside_map interface card crypto outside
    trustpool crypto ca policy
    IKEv2 crypto policy 1
    aes-256 encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 10
    aes-192 encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 20
    aes encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 30
    3des encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    IKEv2 crypto policy 40
    the Encryption
    integrity sha
    Group 2 of 5
    FRP sha
    second life 86400
    Crypto ikev2 allow outside
    Crypto ikev1 allow outside
    IKEv1 crypto policy 10
    authentication crack
    aes-256 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 20
    authentication rsa - sig
    aes-256 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 30
    preshared authentication
    aes-256 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 40
    authentication crack
    aes-192 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 50
    authentication rsa - sig
    aes-192 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 60
    preshared authentication
    aes-192 encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 70
    authentication crack
    aes encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 80
    authentication rsa - sig
    aes encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 90
    preshared authentication
    aes encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 100
    authentication crack
    3des encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 110
    authentication rsa - sig
    3des encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 120
    preshared authentication
    3des encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 130
    authentication crack
    the Encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 140
    authentication rsa - sig
    the Encryption
    sha hash
    Group 2
    life 86400
    IKEv1 crypto policy 150
    preshared authentication
    the Encryption
    sha hash
    Group 2
    life 86400
    Telnet timeout 5
    SSH 77.75.100.208 255.255.255.240 outside
    SSH 92.51.193.156 255.255.255.252 outside
    SSH timeout 5
    Console timeout 0

    dhcpd outside auto_config
    !
    a basic threat threat detection
    Statistics-list of access threat detection
    no statistical threat detection tcp-interception
    internal GroupPolicy_92.51.193.158 group strategy
    attributes of Group Policy GroupPolicy_92.51.193.158
    VPN-tunnel-Protocol ikev1, ikev2
    username password 6e6Djaz3W/XH59zX gordon encrypted privilege 15
    tunnel-group 92.51.193.158 type ipsec-l2l
    tunnel-group 92.51.193.158 General-attributes
    Group - default policy - GroupPolicy_92.51.193.158
    IPSec-attributes tunnel-group 92.51.193.158
    IKEv1 pre-shared-key *.
    remote control-IKEv2 pre-shared-key authentication *.
    pre-shared-key authentication local IKEv2 *.
    !
    class-map inspection_default
    match default-inspection-traffic
    !
    !
    type of policy-card inspect dns preset_dns_map
    parameters
    maximum message length automatic of customer
    message-length maximum 512
    Policy-map global_policy
    class inspection_default
    inspect the preset_dns_map dns
    inspect the ftp
    inspect h323 h225
    inspect the h323 ras
    inspect the rsh
    inspect the rtsp
    inspect esmtp
    inspect sqlnet
    inspect the skinny
    inspect sunrpc
    inspect xdmcp
    inspect the sip
    inspect the netbios
    inspect the tftp
    Review the ip options
    inspect the icmp
    !
    global service-policy global_policy
    context of prompt hostname
    no remote anonymous reporting call
    Cryptochecksum:83b2069fa311e6037163ae74f9b2bec2
    : end

    Hello

    There are some clear problems I see on a quick glance. These are not related to the actual VPN configuration but rather the NAT configurations.

    All your configuration of NAT CLI format above are configured as manual NAT / double NAT in Section 1. This means that the appliance NAT configurations have been added to the same section of the NAT configurations and scheduling of the NAT inside this Section rules is the cause of the problem for the L2L VPN connection for some.

    Here are a few suggestions on what to change

    ASA1

    Minimal changes

    the object of the LAN network

    192.168.10.0 subnet 255.255.255.0

    being REMOTE-LAN network

    255.255.255.0 subnet 192.168.100.0

    NAT (inside, outside) 1 static source LAN LAN to static destination REMOTE - LAN LAN

    no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 non-proxy-arp-search of route static destination

    That means foregoing is first of all create 'object' that contain the local LAN and remote LANs. Then, it creates a NAT0 rule and adds to the top rules NAT. (number 1). It is essentially of at least one of the problems preventing the VPN operation or traffic that cross.

    Finally, we remove the old rule that generated the ASDM. It would do the same thing if it has been moved to the top, but I generally find the creation of the 'object' with descriptive names easier on the eyes in the long term.

    Other suggestions

    These changes are not necessary with regard to the VPN L2L. Here are some suggestions how to clean a part of NAT configurations.

    PAT-SOURCE network object-group

    source networks internal PAT Description

    object-network 192.168.10.0 255.255.255.0

    object-network 192.168.20.0 255.255.255.0

    object-network 192.168.40.0 255.255.255.0

    NAT interface (it is, outside) the after-service automatic PAT-SOURCE dynamic source

    No source (indoor, outdoor) nat Dynamics one interface

    no nat (wireless, outdoors) source Dynamics one interface

    no nat (servers, outside) no matter what source dynamic interface

    The above configuration creates a "object-group" that lists all internal networks that you have dynamic PAT configured so far. It then uses the ' object-group ' in a command unique 'nat' to manage the dynamic PAT for all internal networks (with the exception of printers who had nothing at first). Then we remove the old PAT dynamic configurations.

    Contains the command "nat" "car after" because it moving this "nat" configuration to the bottom of the NAT rules. For this reason its less likely to cause problems in the future.

    network of the SERVERS object

    subnet 192.168.20.0 255.255.255.0

    network of the VPN-POOL object

    192.168.50.0 subnet 255.255.255.0

    NAT (servers, external) 2 static static source of destination of SERVERS SERVERS VPN-VPN-POOL

    no nat (servers, external) static source NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.50.0_24 NETWORK_OBJ_192.168.50.0_24 non-proxy-arp-search of route static destination

    The above configuration is supposed to create a NAT0 configuration for traffic between the network and the pool of Client VPN server. To my knowledge the old configuration that remove us is not used because the traffic would have matched PAT rule dynamic server yet rather than this rule which is later in the NAT configurations and would not be addressed.

    no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination

    It seems to me that network 192.168.1.0/24 is not configured from anywhere in your network. Therefore, the above 'nat' configuration seems useless, can be deleted. If I missed something and its use in then of course do not remove it.

    ASA2

    Minimal changes

    the object of the LAN network

    255.255.255.0 subnet 192.168.100.0

    being REMOTE-LAN network

    192.168.10.0 subnet 255.255.255.0

    NAT (inside, outside) 1 static source LAN LAN to static destination REMOTE - LAN LAN

    no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 non-proxy-arp-search of route static destination

    That means foregoing is first of all create 'object' that contain the local LAN and remote LANs. Then, it creates a NAT0 rule and adds to the top rules NAT. (number 1). It is essentially of at least one of the problems preventing the VPN operation or traffic that cross.

    Finally, we remove the old rule that generated the ASDM.

    Other suggestions

    PAT-SOURCE network object-group

    object-network 192.168.100.0 255.255.255.0

    NAT interface (it is, outside) the after-service automatic PAT-SOURCE dynamic source

    No source (indoor, outdoor) nat Dynamics one interface

    The above configuration is supposed to do the same thing with the other ASA. Although given that this network contains only a single subnet it cleans the "nat" configurations exist that much. But the order of the "nat" configurations is changed to avoid further problems with the NAT order.

    no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination

    It seems to me that network 192.168.1.0/24 is not configured from anywhere in your network. Therefore, the above 'nat' configuration seems useless, can be deleted. If I missed something and its use in then of course do not remove it.

    I suggest trying the changes related to VPN L2L first NAT0 configurations and test traffic. So who gets the work of connectivity, then you could consider changing other NAT configurations. There are other things that could be changed also in what concerns THAT static NAT servers but that probably better left for another time.

    Hope this makes any sense and has helped

    Remember to mark a reply as the answer if it answered your question.

    Feel free to ask more if necessary

    -Jouni

  • Cannot access any internal IPs when you are connected by VPN to ASA5505

    Hello

    I was able to configure VPN to work a bit on my ASA 5505. I can connect to the VPN and ping some IP addresses within the network. But some IPs don't react, I get "Request Timed Out"

    For example:

    10.10.0.4 - it works
    10.10.0.5 - is not word
    10.10.0.10 - it works
    10.10.0.11 - it works
    10.10.0.13 - does not work

    If I ping from the network internally, all works well.

    Does anyone have recommendations on how to address the issue?

    VPN is the marking of the packages in a way that would trigger a firewall block?

    It is the configuration of my ASA:

    VPN with the name 'VPN-Remote' is the one I use.

     ASA Version 9.2(2)4 ! hostname ciscoasa enable password NuLKvvWGg.x9HEKO encrypted passwd NuLKvvWGg.x9HEKO encrypted names ip local pool RA_VPN 10.10.1.1-10.10.1.255 mask 255.255.255.0 ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 10.10.0.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address dhcp setroute ipv6 enable ! boot system disk0:/asa922-4-k8.bin ftp mode passive clock timezone CST -6 clock summer-time CDT recurring same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network obj_any subnet 0.0.0.0 0.0.0.0 object network INSIDE-SUBNET object network sb-service-80 host 10.10.0.143 object network sbservicetest object network sb-service-443 host 10.10.0.143 object network dvr_web host 10.10.0.30 object service DVR-Tomcat_port service tcp source eq 8080 destination eq 8080 object network NETWORK_OBJ_10.10.1.0_24 subnet 10.10.1.0 255.255.255.0 object network dvr_mobile host 10.10.0.30 object service DVR-Mobile_port service tcp source eq 18004 destination eq 18004 object network WAN host 98.195.48.88 object service Web80 service tcp source eq www destination eq www object network NETWORK_OBJ_10.10.2.0_24 subnet 10.10.2.0 255.255.255.0 object network NETWORK_OBJ_10.10.0.0_24 subnet 10.10.0.0 255.255.255.0 object-group network sb-service network-object object sb-service-443 network-object object sb-service-80 object-group network DVR-service network-object object dvr_web network-object object dvr_mobile object-group protocol TCPUDP protocol-object udp protocol-object tcp access-list outside_access_in extended permit icmp any any access-list inside_access_in extended permit ip any any access-list inside_access_in extended permit icmp any any inactive access-list Outside_access_in extended permit tcp any object sb-service-80 eq www access-list Outside_access_in extended permit tcp any object sb-service-443 eq https log disable access-list Outside_access_in extended permit tcp any object dvr_web eq 8080 log disable access-list Outside_access_in extended permit tcp any object dvr_mobile eq 18004 log disable access-list Outside_access_in extended permit icmp any any time-exceeded access-list Outside_access_in extended permit icmp any any unreachable log warnings access-list Outside_access_in extended permit icmp any any echo-reply access-list Outside_access_in extended permit icmp any any source-quench access-list global_mpc extended permit ip any any access-list RA_VPN-ACL extended permit ip object NETWORK_OBJ_10.10.2.0_24 any access-list Remote-VPN_splitTunnelAcl standard permit 10.10.0.0 255.255.255.0 access-list AnyConnect_Client_Local_Print extended deny ip any4 any4 access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq lpd access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 631 access-list AnyConnect_Client_Local_Print remark Windows' printing port access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 9100 access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol access-list AnyConnect_Client_Local_Print extended permit udp any4 host 224.0.0.251 eq 5353 access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol access-list AnyConnect_Client_Local_Print extended permit udp any4 host 224.0.0.252 eq 5355 access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol access-list AnyConnect_Client_Local_Print extended permit tcp any4 any4 eq 137 access-list AnyConnect_Client_Local_Print extended permit udp any4 any4 eq netbios-ns pager lines 24 logging enable logging asdm notifications no logging message 106015 no logging message 313001 no logging message 313008 no logging message 106023 no logging message 710003 no logging message 106100 no logging message 302015 no logging message 302014 no logging message 302013 no logging message 302018 no logging message 302017 no logging message 302016 no logging message 302021 no logging message 302020 flow-export destination inside 10.10.0.111 2055 mtu inside 1500 mtu outside 1500 no failover icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-731.bin no asdm history enable arp timeout 14400 no arp permit-nonconnected nat (any,any) source static NETWORK_OBJ_10.10.1.0_24 NETWORK_OBJ_10.10.1.0_24 ! object network obj_any nat (inside,outside) dynamic interface object network sb-service-80 nat (inside,outside) static interface no-proxy-arp service tcp www www object network sb-service-443 nat (inside,outside) static interface no-proxy-arp service tcp https https object network dvr_web nat (inside,outside) static interface no-proxy-arp service tcp 8080 8080 object network dvr_mobile nat (inside,outside) static interface no-proxy-arp service tcp 18004 18004 ! nat (inside,outside) after-auto source dynamic any interface inactive access-group inside_access_in in interface inside access-group Outside_access_in in interface outside timeout xlate 3:00:00 timeout pat-xlate 0:00:30 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy user-identity default-domain LOCAL aaa authentication ssh console LOCAL http server enable http 10.10.0.0 255.255.255.0 inside http 0.0.0.0 0.0.0.0 outside snmp-server group snmp_g v3 auth snmp-server user snmp_u snmp_g v3 encrypted auth md5 1d:1b:67:96:29:9b:5c:49:42:d5:a4:10:13:e0:b2:ee snmp-server host inside 10.10.0.111 community ***** version 2c no snmp-server location no snmp-server contact snmp-server community ***** crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transport crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transport crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transport crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transport crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transport crypto ipsec ikev2 ipsec-proposal DES protocol esp encryption des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal 3DES protocol esp encryption 3des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES protocol esp encryption aes protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES192 protocol esp encryption aes-192 protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES256 protocol esp encryption aes-256 protocol esp integrity sha-1 md5 crypto ipsec security-association pmtu-aging infinite crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-192-SHA ESP-AES-256-SHA ESP-3DES-SHA ESP-DES-SHA ESP-AES-128-SHA-TRANS ESP-AES-192-SHA-TRANS ESP-AES-256-SHA-TRANS ESP-3DES-SHA-TRANS ESP-DES-SHA-TRANS crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map inside_map interface inside crypto ca trustpoint ASDM_Launcher_Access_TrustPoint_0 enrollment self subject-name CN=10.10.0.1,CN=ciscoasa crl configure crypto ca trustpoint ASDM_TrustPoint0 enrollment self subject-name CN=ciscoasa proxy-ldc-issuer crl configure crypto ca trustpool policy crypto ca certificate chain ASDM_TrustPoint0 certificate aa711054 308201af 30820159 a0030201 020204aa 71105430 0d06092a 864886f7 0d010105 0500302c 3111300f 06035504 03130863 6973636f 61736131 17301506 092a8648 86f70d01 09021608 63697363 6f617361 301e170d 31353035 32303230 34353137 5a170d32 35303531 37323034 3531375a 302c3111 300f0603 55040313 08636973 636f6173 61311730 1506092a 864886f7 0d010902 16086369 73636f61 7361305c 300d0609 2a864886 f70d0101 01050003 4b003048 024100bc 4278aeda 26601456 0e035bb5 6021adc5 0ac9149a 11d95e72 c5a8509b 514fd50d 7a86bdb3 a00bda84 4e6bda8d 50124c64 1179acc4 b2869092 9a742b52 f97c2302 03010001 a3633061 300f0603 551d1301 01ff0405 30030101 ff300e06 03551d0f 0101ff04 04030201 86301f06 03551d23 04183016 8014d86a b4f1585d 7d93a0c7 7a1df9dd b37b0051 18aa301d 0603551d 0e041604 14d86ab4 f1585d7d 93a0c77a 1df9ddb3 7b005118 aa300d06 092a8648 86f70d01 01050500 034100a3 f0441214 1add483b 286fa44e 3844acce 27a68b2e 54f21dce 9a917783 1ab394f7 2d87e4d4 bcfcc7ef 6b26d604 bd0ea56f 05a72d0d 6c37413a b60216f3 612e0a quit crypto ikev2 policy 1 encryption aes-256 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 10 encryption aes-192 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 20 encryption aes integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 30 encryption 3des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 40 encryption des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 enable outside crypto ikev1 enable outside crypto ikev1 policy 10 authentication crack encryption aes-256 hash sha group 2 lifetime 86400 crypto ikev1 policy 20 authentication rsa-sig encryption aes-256 hash sha group 2 lifetime 86400 crypto ikev1 policy 30 authentication pre-share encryption aes-256 hash sha group 2 lifetime 86400 crypto ikev1 policy 40 authentication crack encryption aes-192 hash sha group 2 lifetime 86400 crypto ikev1 policy 50 authentication rsa-sig encryption aes-192 hash sha group 2 lifetime 86400 crypto ikev1 policy 60 authentication pre-share encryption aes-192 hash sha group 2 lifetime 86400 crypto ikev1 policy 70 authentication crack encryption aes hash sha group 2 lifetime 86400 crypto ikev1 policy 80 authentication rsa-sig encryption aes hash sha group 2 lifetime 86400 crypto ikev1 policy 90 authentication pre-share encryption aes hash sha group 2 lifetime 86400 crypto ikev1 policy 100 authentication crack encryption 3des hash sha group 2 lifetime 86400 crypto ikev1 policy 110 authentication rsa-sig encryption 3des hash sha group 2 lifetime 86400 crypto ikev1 policy 120 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto ikev1 policy 130 authentication crack encryption des hash sha group 2 lifetime 86400 crypto ikev1 policy 140 authentication rsa-sig encryption des hash sha group 2 lifetime 86400 crypto ikev1 policy 150 authentication pre-share encryption des hash sha group 2 lifetime 86400 telnet timeout 5 ssh stricthostkeycheck ssh 10.10.0.0 255.255.255.0 inside ssh timeout 5 ssh key-exchange group dh-group1-sha1 console timeout 0 no vpn-addr-assign dhcp dhcpd auto_config outside ! dhcpd address 10.10.0.5-10.10.0.254 inside ! threat-detection basic-threat threat-detection statistics port threat-detection statistics protocol threat-detection statistics access-list threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200 ntp server 166.70.136.41 source outside ntp server 108.166.189.70 source outside ntp server 63.245.214.136 source outside ssl trust-point ASDM_Launcher_Access_TrustPoint_0 inside ssl trust-point ASDM_Launcher_Access_TrustPoint_0 inside vpnlb-ip webvpn enable outside group-policy DfltGrpPolicy attributes group-policy Remote-VPN internal group-policy Remote-VPN attributes dns-server value 10.10.0.201 8.8.8.8 vpn-tunnel-protocol ikev1 split-tunnel-policy tunnelspecified split-tunnel-network-list value Remote-VPN_splitTunnelAcl default-domain value local.prv username snmp_test password Ocwq862v84DTwooX encrypted username VPN_User password KgHsdRdYP0lAyeqPIXn51g== nt-encrypted privilege 15 tunnel-group DefaultRAGroup general-attributes address-pool RA_VPN tunnel-group DefaultRAGroup ipsec-attributes ikev1 pre-shared-key ***** tunnel-group Remote-VPN type remote-access tunnel-group Remote-VPN general-attributes address-pool RA_VPN default-group-policy Remote-VPN tunnel-group Remote-VPN ipsec-attributes ikev1 pre-shared-key ***** ! class-map global-class match access-list global_mpc class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options inspect pptp inspect icmp inspect icmp error class global-class flow-export event-type all destination 10.10.0.111 ! service-policy global_policy global prompt hostname context no call-home reporting anonymous hpm topN enable Cryptochecksum:f249b6940d463cc987b9aa828d8d8282 : end

    Hello

    If please check windows or any of application firewall PC side. It's less likely the issue VPN or ASA.

    HTH

    Averroès.

  • VPN PPTP settings

    I installed a PPTP VPN connection to my Cisco router, and it works, but not completely. Is it possible that when someone connects they can interrogate our internal DNS server for address resolution? Also when they connect, they can no longer browse the Internet, since the a route statement directs all in the VPN. Is it possible to set up split tunneling?

    Thank you.

    For DNS resolution, use the following commands in the virtual-template int (or whatever int you use):

    PPP ipcp dns x.x.x.x y.y.y.y

    PPP ipcp wins a.a.a.a b.b.b.b

    As you can see, this is going to happen on the DNS and WINS servers to the client, obviously x.x.x.x will be your internal DNS server. You can add y.y.y.y if you have a DNS backup, otherwise do not.

    Regarding the split of tunnelling, there is no concept of split tunneling in the PPP protocol, it's basically all or nothing. You can add a static route to the internal network, pointing to the negotiated IP address, but there is no way of knowing the IP address until the tunnel is built, it is not too easy to use.

    See http://www.cisco.com/warp/customer/707/pptp.shtml#add5 for more details.

  • Problem with ASA 5505 VPN remote access

    After about 1 year to have the VPN Client from Cisco connection to an ASA 5505 with no problems, all of a sudden one day it stops working. The customer is able to get a connection to the ASA and browse the local network for only about 30 seconds after the connection. After that, no access is available to the network behind the ASA. I have tried everything I can think of to try to solve the problem, but at this point, I'm just banging my head against a wall. Anyone know what could cause this?

    Here is the cfg running of the ASA

    ----------------------------------------------------------------------------------------

    : Saved

    :

    ASA Version 8.4 (1)

    !

    hostname NCHCO

    enable encrypted password xxxxxxxxxxxxxxx

    xxxxxxxxxxx encrypted passwd

    names of

    description of NCHCO name 192.168.2.0 City offices

    name 192.168.2.80 VPN_End

    name 192.168.2.70 VPN_Start

    !

    interface Vlan1

    nameif inside

    security-level 100

    IP 192.168.2.1 255.255.255.0

    !

    interface Vlan2

    nameif outside

    security-level 0

    IP address **. ***. 255.255.255.248

    !

    interface Ethernet0/0

    switchport access vlan 2

    Speed 100

    full duplex

    !

    interface Ethernet0/1

    !

    interface Ethernet0/2

    !

    interface Ethernet0/3

    !

    interface Ethernet0/4

    !

    interface Ethernet0/5

    !

    interface Ethernet0/6

    !

    interface Ethernet0/7

    !

    boot system Disk0: / asa841 - k8.bin

    passive FTP mode

    network of the NCHCO object

    Subnet 192.168.2.0 255.255.255.0

    network object obj - 192.168.1.0

    subnet 192.168.1.0 255.255.255.0

    network object obj - 192.168.2.64

    subnet 192.168.2.64 255.255.255.224

    network object obj - 0.0.0.0

    subnet 0.0.0.0 255.255.255.0

    network obj_any object

    subnet 0.0.0.0 0.0.0.0

    the Web server object network

    the FINX object network

    Home 192.168.2.11

    rdp service object

    source between 1-65535 destination eq 3389 tcp service

    Rdp description

    outside_nat0_outbound extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0

    outside_nat0_outbound extended access list permit ip object NCHCO 192.168.2.0 255.255.255.0

    inside_nat0_outbound extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0

    inside_nat0_outbound list of allowed ip extended access all 192.168.2.64 255.255.255.224

    permit access list extended ip 0.0.0.0 inside_nat0_outbound 255.255.255.0 192.168.2.64 255.255.255.224

    outside_1_cryptomap extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0

    outside_1_cryptomap_1 extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0

    LAN_Access list standard access allowed 192.168.2.0 255.255.255.0

    LAN_Access list standard access allowed 0.0.0.0 255.255.255.0

    NCHCO_splitTunnelAcl_1 list standard access allowed 192.168.2.0 255.255.255.0

    AnyConnect_Client_Local_Print deny ip extended access list a whole

    AnyConnect_Client_Local_Print list extended access permit tcp any any eq lpd

    Note AnyConnect_Client_Local_Print of access list IPP: Internet Printing Protocol

    AnyConnect_Client_Local_Print list extended access permit tcp any any eq 631

    print the access-list AnyConnect_Client_Local_Print Note Windows port

    AnyConnect_Client_Local_Print list extended access permit tcp any any eq 9100

    access-list AnyConnect_Client_Local_Print mDNS Note: multicast DNS protocol

    AnyConnect_Client_Local_Print list extended access permit udp any host 224.0.0.251 eq 5353

    AnyConnect_Client_Local_Print of access list LLMNR Note: link Local Multicast Name Resolution protocol

    AnyConnect_Client_Local_Print list extended access permit udp any host 224.0.0.252 eq 5355

    Note access list TCP/NetBIOS protocol AnyConnect_Client_Local_Print

    AnyConnect_Client_Local_Print list extended access permit tcp any any eq 137

    AnyConnect_Client_Local_Print list extended access udp allowed any any eq netbios-ns

    outside_access_in list extended access permit tcp any object FINX eq 3389

    outside_access_in_1 list extended access allowed object rdp any object FINX

    pager lines 24

    Enable logging

    asdm of logging of information

    Within 1500 MTU

    Outside 1500 MTU

    mask of VPN_Pool VPN_Start VPN_End of local pool IP 255.255.255.0

    ICMP unreachable rate-limit 1 burst-size 1

    ASDM image disk0: / asdm - 649.bin

    don't allow no asdm history

    ARP timeout 14400

    NAT (inside, all) static source NCHCO destination NCHCO static obj - 192.168.1.0 obj - 192.168.1.0

    NAT (inside, all) static source any any destination static obj - 192.168.2.64 obj - 192.168.2.64

    NAT (inside, all) source static obj - 0.0.0.0 0.0.0.0 - obj destination static obj - 192.168.2.64 obj - 192.168.2.64

    !

    network obj_any object

    NAT dynamic interface (indoor, outdoor)

    the FINX object network

    NAT (inside, outside) interface static service tcp 3389 3389

    Access-group outside_access_in_1 in interface outside

    Route outside 0.0.0.0 0.0.0.0 69.61.228.177 1

    Timeout xlate 03:00

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    timeout tcp-proxy-reassembly 0:01:00

    dynamic-access-policy-registration DfltAccessPolicy

    network-acl outside_nat0_outbound

    WebVPN

    SVC request to enable default svc

    Enable http server

    http 192.168.1.0 255.255.255.0 inside

    http *. **. ***. 255.255.255.255 outside

    http *. **. ***. 255.255.255.255 outside

    http NCHCO 255.255.255.0 inside

    http 96.11.251.186 255.255.255.255 outside

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

    Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

    Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

    Crypto ipsec transform-set esp-3des esp-sha-hmac ikev1 l2tp-transform

    IKEv1 crypto ipsec transform-set l2tp-transformation mode transit

    Crypto ipsec transform-set vpn-transform ikev1 esp-aes-256 esp-sha-hmac

    Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA ikev1

    transport mode encryption ipsec transform-set TRANS_ESP_3DES_SHA ikev1

    Crypto ipsec transform-set esp-3des esp-md5-hmac TRANS_ESP_3DES_MD5 ikev1

    transport mode encryption ipsec transform-set TRANS_ESP_3DES_MD5 ikev1

    Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

    crypto dynamic-map dyn-map 10 set pfs Group1

    crypto dynamic-map dyn-map 10 set transform-set l2tp vpn-transform processing ikev1

    dynamic-map encryption dyn-map 10 value reverse-road

    Crypto-map dynamic outside_dyn_map 20 set transform-set ESP-3DES-SHA ikev1

    Crypto-map dynamic outside_dyn_map 20 the value reverse-road

    card crypto outside_map 1 match address outside_1_cryptomap

    card crypto outside_map 1 set pfs Group1

    peer set card crypto outside_map 1 74.219.208.50

    card crypto outside_map 1 set transform-set ESP-3DES-SHA ikev1

    map outside_map 20-isakmp ipsec crypto dynamic outside_dyn_map

    outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

    outside_map interface card crypto outside

    inside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

    inside crypto map inside_map interface

    card crypto vpn-map 1 match address outside_1_cryptomap_1

    card crypto vpn-card 1 set pfs Group1

    set vpn-card crypto map peer 1 74.219.208.50

    card crypto 1 set transform-set ESP-3DES-SHA ikev1 vpn-map

    dynamic vpn-map 10 dyn-map ipsec isakmp crypto map

    crypto isakmp identity address

    Crypto ikev1 allow inside

    Crypto ikev1 allow outside

    IKEv1 crypto ipsec-over-tcp port 10000

    IKEv1 crypto policy 10

    preshared authentication

    3des encryption

    md5 hash

    Group 2

    life 86400

    IKEv1 crypto policy 15

    preshared authentication

    aes-256 encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 35

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    enable client-implementation to date

    Telnet 192.168.1.0 255.255.255.0 inside

    Telnet NCHCO 255.255.255.0 inside

    Telnet timeout 5

    SSH 192.168.1.0 255.255.255.0 inside

    SSH NCHCO 255.255.255.0 inside

    SSH timeout 5

    Console timeout 0

    dhcpd address 192.168.2.150 - 192.168.2.225 inside

    dhcpd dns 216.68.4.10 216.68.5.10 interface inside

    lease interface 64000 dhcpd inside

    !

    a basic threat threat detection

    Statistics-list of access threat detection

    no statistical threat detection tcp-interception

    WebVPN

    internal DefaultRAGroup group strategy

    attributes of Group Policy DefaultRAGroup

    value of server DNS 192.168.2.1

    L2TP ipsec VPN-tunnel-Protocol ikev1

    nchco.local value by default-field

    attributes of Group Policy DfltGrpPolicy

    value of server DNS 192.168.2.1

    L2TP ipsec VPN-tunnel-Protocol ikev1 ssl-clientless ssl-client

    allow password-storage

    enable IPSec-udp

    enable dhcp Intercept 255.255.255.0

    the address value VPN_Pool pools

    internal NCHCO group policy

    NCHCO group policy attributes

    value of 192.168.2.1 DNS Server 8.8.8.8

    Ikev1 VPN-tunnel-Protocol

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list NCHCO_splitTunnelAcl_1

    value by default-field NCHCO.local

    admin LbMiJuAJjDaFb2uw encrypted privilege 15 password username

    username privilege 15 encrypted password yB1lHEVmHZGj5C2Z 8njferg

    username NCHvpn99 password dhn. JzttvRmMbHsP encrypted

    attributes global-tunnel-group DefaultRAGroup

    address (inside) VPN_Pool pool

    address pool VPN_Pool

    authentication-server-group (inside) LOCAL

    authentication-server-group (outside LOCAL)

    LOCAL authority-server-group

    authorization-server-group (inside) LOCAL

    authorization-server-group (outside LOCAL)

    Group Policy - by default-DefaultRAGroup

    band-Kingdom

    band-band

    IPSec-attributes tunnel-group DefaultRAGroup

    IKEv1 pre-shared-key *.

    NOCHECK Peer-id-validate

    tunnel-group DefaultRAGroup ppp-attributes

    No chap authentication

    no authentication ms-chap-v1

    ms-chap-v2 authentication

    tunnel-group DefaultWEBVPNGroup ppp-attributes

    PAP Authentication

    ms-chap-v2 authentication

    tunnel-group 74.219.208.50 type ipsec-l2l

    IPSec-attributes tunnel-group 74.219.208.50

    IKEv1 pre-shared-key *.

    type tunnel-group NCHCO remote access

    attributes global-tunnel-group NCHCO

    address pool VPN_Pool

    Group Policy - by default-NCHCO

    IPSec-attributes tunnel-group NCHCO

    IKEv1 pre-shared-key *.

    !

    class-map inspection_default

    match default-inspection-traffic

    !

    !

    type of policy-card inspect dns preset_dns_map

    parameters

    maximum message length automatic of customer

    message-length maximum 512

    Policy-map global_policy

    class inspection_default

    inspect the preset_dns_map dns

    inspect the ftp

    inspect h323 h225

    inspect the h323 ras

    inspect the rsh

    inspect the rtsp

    inspect esmtp

    inspect sqlnet

    inspect the skinny

    inspect sunrpc

    inspect xdmcp

    inspect the sip

    inspect the netbios

    inspect the tftp

    Review the ip options

    !

    global service-policy global_policy

    context of prompt hostname

    call-home

    Profile of CiscoTAC-1

    no active account

    http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

    email address of destination [email protected] / * /

    destination-mode http transport

    Subscribe to alert-group diagnosis

    Subscribe to alert-group environment

    Subscribe to alert-group monthly periodic inventory

    monthly periodicals to subscribe to alert-group configuration

    daily periodic subscribe to alert-group telemetry

    Cryptochecksum:a2110206e1af06974c858fb40c6de2fc

    : end

    ASDM image disk0: / asdm - 649.bin

    ASDM VPN_Start 255.255.255.255 inside location

    ASDM VPN_End 255.255.255.255 inside location

    don't allow no asdm history

    ---------------------------------------------------------------------------------------------------------------

    And here are the logs of the Cisco VPN Client when sailing, then is unable to browse the network behind the ASA:

    ---------------------------------------------------------------------------------------------------------------

    Cisco Systems VPN Client Version 5.0.07.0440

    Copyright (C) 1998-2010 Cisco Systems, Inc.. All rights reserved.

    Customer type: Windows, Windows NT

    Running: 6.1.7601 Service Pack 1

    Config files directory: C:\Program Files (x 86) \Cisco Systems\VPN Client\

    1 09:44:55.677 01/10/13 Sev = Info/6 CERT / 0 x 63600026

    Try to find a certificate using hash Serial.

    2 09:44:55.677 01/10/13 Sev = Info/6 CERT / 0 x 63600027

    Found a certificate using hash Serial.

    3 09:44:55.693 01/10/13 Sev = Info/6 GUI/0x63B00011

    RELOADED successfully certificates in all certificate stores.

    4 09:45:02.802 10/01/13 Sev = Info/4 CM / 0 x 63100002

    Start the login process

    5 09:45:02.802 01/10/13 Sev = Info/4 CM / 0 x 63100004

    Establish a secure connection

    6 09:45:02.802 01/10/13 Sev = Info/4 CM / 0 x 63100024

    Attempt to connect with the server "*." **. ***. *** »

    7 09:45:02.802 10/01/13 Sev = Info/6 IKE/0x6300003B

    Try to establish a connection with *. **. ***. ***.

    8 09:45:02.818 10/01/13 Sev = Info/4 IKE / 0 x 63000001

    From IKE Phase 1 negotiation

    9 09:45:02.865 10/01/13 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Frag), VID(Nat-T), VID (Unity)) to *. **. ***. ***

    10 09:45:02.896 10/01/13 Sev = Info/5 IKE/0x6300002F

    Received packet of ISAKMP: peer = *. **. ***. ***

    11 09:45:02.896 10/01/13 Sev = Info/4 IKE / 0 x 63000014

    RECEIVING< isakmp="" oak="" ag="" (sa,="" ke,="" non,="" id,="" hash,="" vid(unity),="" vid(xauth),="" vid(dpd),="" vid(nat-t),="" nat-d,="" nat-d,="" vid(frag),="" vid(?))="" from="">

    12 09:45:02.896 10/01/13 Sev = Info/5 IKE / 0 x 63000001

    Peer is a compatible peer Cisco-Unity

    13 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001

    Peer supports XAUTH

    14 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001

    Peer supports the DPD

    15 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001

    Peer supports NAT - T

    16 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001

    Peer supports fragmentation IKE payloads

    17 09:45:02.927 01/10/13 Sev = Info/6 IKE / 0 x 63000001

    IOS Vendor ID successful construction

    18 09:45:02.927 01/10/13 Sev = Info/4 IKE / 0 x 63000013

    SENDING > ISAKMP OAK AG * (HASH, NOTIFY: NAT - D, NAT - D, VID (?), STATUS_INITIAL_CONTACT, VID (Unity)) to *. **. ***. ***

    19 09:45:02.927 01/10/13 Sev = Info/4 IKE / 0 x 63000083

    IKE port in use - Local Port = 0xDD3B, Remote Port = 0x01F4

    20 09:45:02.927 01/10/13 Sev = Info/5 IKE / 0 x 63000072

    Automatic NAT detection status:

    Remote endpoint is NOT behind a NAT device

    This effect is NOT behind a NAT device

    21 09:45:02.927 01/10/13 Sev = Info/4 CM/0x6310000E

    ITS established Phase 1.  1 crypto IKE Active SA, 0 IKE SA authenticated user in the system

    22 09:45:02.943 10/01/13 Sev = Info/5 IKE/0x6300002F

    Received packet of ISAKMP: peer = *. **. ***. ***

    23 09:45:02.943 01/10/13 Sev = Info/4 IKE / 0 x 63000014

    RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">

    24 09:45:02.943 01/10/13 Sev = Info/4 CM / 0 x 63100015

    Launch application xAuth

    25 09:45:03.037 01/10/13 Sev = Info/6 GUI/0x63B00012

    Attributes of the authentication request is 6: 00.

    26 09:45:03.037 01/10/13 Sev = Info/4 CM / 0 x 63100017

    xAuth application returned

    27 09:45:03.037 10/01/13 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***

    28 09:45:03.037 10/01/13 Sev = Info/4 IPSEC / 0 x 63700008

    IPSec driver started successfully

    29 09:45:03.037 01/10/13 Sev = Info/4 IPSEC / 0 x 63700014

    Remove all keys

    30 09:45:03.083 01/10/13 Sev = Info/5 IKE/0x6300002F

    Received packet of ISAKMP: peer = *. **. ***. ***

    31 09:45:03.083 01/10/13 Sev = Info/4 IKE / 0 x 63000014

    RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">

    32 09:45:03.083 01/10/13 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***

    33 09:45:03.083 01/10/13 Sev = Info/4 CM/0x6310000E

    ITS established Phase 1.  1 crypto IKE Active SA, 1 IKE SA authenticated user in the system

    34 09:45:03.083 01/10/13 Sev = Info/5 IKE/0x6300005E

    Customer address a request from firewall to hub

    35 09:45:03.083 01/10/13 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***

    36 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300002F

    Received packet of ISAKMP: peer = *. **. ***. ***

    37 09:45:03.146 01/10/13 Sev = Info/4 IKE / 0 x 63000014

    RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="" **.**.***.***="" isakmp="" oak="" trans="" *(hash,="" attr)="" from="">

    38 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010

    MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS:, value = 192.168.2.70

    39 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010

    MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK:, value = 255.255.255.0

    40 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010

    MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (1):, value = 192.168.2.1

    41 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010

    MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (2):, value = 8.8.8.8

    42 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D

    MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD:, value = 0x00000001

    43 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D

    MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SPLIT_INCLUDE (# of split_nets), value = 0x00000001

    44 09:45:03.146 10/01/13 Sev = Info/5 IKE/0x6300000F

    SPLIT_NET #1

    = 192.168.2.0 subnet

    mask = 255.255.255.0

    Protocol = 0

    SRC port = 0

    port dest = 0

    45 09:45:03.146 10/01/13 Sev = Info/5 IKE/0x6300000E

    MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN:, value = NCHCO.local

    46 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D

    MODE_CFG_REPLY: Attribute = MODECFG_UNITY_UDP_NAT_PORT, value = 0 x 00002710

    47 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D

    MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS:, value = 0x00000000

    48 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000E

    MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = 8.4 (1) Cisco systems, Inc. ASA5505 Version built by manufacturers on Tuesday, January 31, 11 02:11

    49 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D

    MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT:, value = 0x00000001

    50 09:45:03.146 01/10/13 Sev = Info/4 CM / 0 x 63100019

    Data in mode Config received

    51 09:45:03.146 01/10/13 Sev = Info/4 IKE / 0 x 63000056

    Received a request from key driver: local IP = 192.168.2.70, GW IP = *. **. ***. remote IP address = 0.0.0.0

    52 09:45:03.146 01/10/13 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK QM * (HASH, SA, NO, ID, ID) to *. **. ***. ***

    53 09:45:03.177 01/10/13 Sev = Info/5 IKE/0x6300002F

    Received packet of ISAKMP: peer = *. **. ***. ***

    54 09:45:03.177 01/10/13 Sev = Info/4 IKE / 0 x 63000014

    RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:status_resp_lifetime)="" from="">

    55 09:45:03.177 01/10/13 Sev = Info/5 IKE / 0 x 63000045

    Answering MACHINE-LIFE notify has value of 86400 seconds

    56 09:45:03.177 01/10/13 Sev = Info/5 IKE / 0 x 63000047

    This SA was already alive for 1 second, expiration of adjustment to 86399 seconds now

    57 09:45:03.193 01/10/13 Sev = Info/5 IKE/0x6300002F

    Received packet of ISAKMP: peer = *. **. ***. ***

    58 09:45:03.193 01/10/13 Sev = Info/4 IKE / 0 x 63000014

    RECEIVING< isakmp="" oak="" qm="" *(hash,="" sa,="" non,="" id,="" id,="" notify:status_resp_lifetime)="" from="">

    59 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000045

    Answering MACHINE-LIFE notify is set to 28800 seconds

    60 09:45:03.193 01/10/13 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK QM * (HASH) to *. **. ***. ***

    61 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000059

    IPsec Security Association of loading (MsgID = SPI OUTBOUND SPI INCOMING = 0x3EBEBFC5 0xAAAF4C1C = 967A3C93)

    62 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000025

    OUTGOING ESP SPI support: 0xAAAF4C1C

    63 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000026

    Charges INBOUND ESP SPI: 0x3EBEBFC5

    64 09:45:03.193 01/10/13 Sev = Info/5 CVPND / 0 x 63400013

    Destination mask subnet Gateway Interface metric

    0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261

    96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261

    96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261

    96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261

    127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306

    127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306

    127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306

    192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261

    192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261

    192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261

    224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306

    224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261

    224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261

    255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306

    255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261

    255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261

    65 09:45:03.521 01/10/13 Sev = Info/6 CVPND / 0 x 63400001

    Launch VAInst64 for controlling IPSec virtual card

    66 09:45:03.896 01/10/13 Sev = Info/4 CM / 0 x 63100034

    The virtual card has been activated:

    IP=192.168.2.70/255.255.255.0

    DNS = 192.168.2.1, 8.8.8.8

    WINS = 0.0.0.0 0.0.0.0

    Domain = NCHCO.local

    Split = DNS names

    67 09:45:03.912 01/10/13 Sev = Info/5 CVPND / 0 x 63400013

    Destination mask subnet Gateway Interface metric

    0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261

    96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261

    96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261

    96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261

    127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306

    127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306

    127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306

    192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261

    192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261

    192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261

    224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306

    224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261

    224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261

    224.0.0.0 240.0.0.0 0.0.0.0 0.0.0.0 261

    255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306

    255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261

    255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261

    255.255.255.255 255.255.255.255 0.0.0.0 0.0.0.0 261

    68 09:45:07.912 01/10/13 Sev = Info/4 CM / 0 x 63100038

    Were saved successfully road to file changes.

    69 09:45:07.912 01/10/13 Sev = Info/5 CVPND / 0 x 63400013

    Destination mask subnet Gateway Interface metric

    0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261

    **. **. ***. 255.255.255.255 96.11.251.1 96.11.251.149 100

    96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261

    96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261

    96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261

    127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306

    127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306

    127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306

    192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261

    192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261

    192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261

    192.168.2.0 255.255.255.0 192.168.2.70 192.168.2.70 261

    192.168.2.0 255.255.255.0 192.168.2.1 192.168.2.70 100

    192.168.2.70 255.255.255.255 192.168.2.70 192.168.2.70 261

    192.168.2.255 255.255.255.255 192.168.2.70 192.168.2.70 261

    224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306

    224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261

    224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261

    224.0.0.0 240.0.0.0 192.168.2.70 192.168.2.70 261

    255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306

    255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261

    255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261

    255.255.255.255 255.255.255.255 192.168.2.70 192.168.2.70 261

    70 09:45:07.912 01/10/13 Sev = Info/6 CM / 0 x 63100036

    The routing table has been updated for the virtual card

    71 09:45:07.912 01/10/13 Sev = Info/4 CM/0x6310001A

    A secure connection established

    72 09:45:07.943 01/10/13 Sev = Info/4 CM/0x6310003B

    Look at address added to 96.11.251.149.  Current host name: psaserver, current address (s): 192.168.2.70, 96.11.251.149, 192.168.1.3.

    73 09:45:07.943 01/10/13 Sev = Info/4 CM/0x6310003B

    Look at address added to 192.168.2.70.  Current host name: psaserver, current address (s): 192.168.2.70, 96.11.251.149, 192.168.1.3.

    74 09:45:07.943 01/10/13 Sev = Info/5 CM / 0 x 63100001

    Did not find the smart card to watch for removal

    75 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700014

    Remove all keys

    76 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700010

    Creates a new key structure

    77 09:45:07.943 01/10/13 Sev = Info/4 IPSEC/0x6370000F

    Adding key with SPI = 0x1c4cafaa in the list of keys

    78 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700010

    Creates a new key structure

    79 09:45:07.943 01/10/13 Sev = Info/4 IPSEC/0x6370000F

    Adding key with SPI = 0xc5bfbe3e in the list of keys

    80 09:45:07.943 01/10/13 Sev = Info/4 IPSEC/0x6370002F

    Assigned WILL interface private addr 192.168.2.70

    81 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700037

    Configure the public interface: 96.11.251.149. SG: **.**.***.***

    82 09:45:07.943 10/01/13 Sev = Info/6 CM / 0 x 63100046

    Define indicator tunnel set up in the registry to 1.

    83 09:45:13.459 01/10/13 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK INFO * (HASH, NOTIFY: DPD_REQUEST) to *. **. ***. ***

    84 09:45:13.459 01/10/13 Sev = Info/6 IKE/0x6300003D

    Upon request of the DPD to *. **. ***. , our seq # = 107205276

    85 09:45:13.474 01/10/13 Sev = Info/5 IKE/0x6300002F

    Received packet of ISAKMP: peer = *. **. ***. ***

    86 09:45:13.474 01/10/13 Sev = Info/4 IKE / 0 x 63000014

    RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:dpd_ack)="" from="">

    87 09:45:13.474 01/10/13 Sev = Info/5 IKE / 0 x 63000040

    Receipt of DPO ACK to *. **. ***. seq # receipt = 107205276, seq # expected is 107205276

    88 09:45:15.959 01/10/13 Sev = Info/4 IPSEC / 0 x 63700019

    Activate key dating SPI = 0x1c4cafaa key with SPI = 0xc5bfbe3e

    89 09:46:00.947 10/01/13 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK INFO * (HASH, NOTIFY: DPD_REQUEST) to *. **. ***. ***

    90 09:46:00.947 01/10/13 Sev = Info/6 IKE/0x6300003D

    Upon request of the DPD to *. **. ***. , our seq # = 107205277

    91 09:46:01.529 01/10/13 Sev = Info/5 IKE/0x6300002F

    Received packet of ISAKMP: peer = *. **. ***. ***

    92 09:46:01.529 01/10/13 Sev = Info/4 IKE / 0 x 63000014

    RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:dpd_ack)="" from="">

    93 09:46:01.529 01/10/13 Sev = Info/5 IKE / 0 x 63000040

    Receipt of DPO ACK to *. **. ***. seq # receipt = 107205277, seq # expected is 107205277

    94 09:46:11.952 01/10/13 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK INFO * (HASH, NOTIFY: DPD_REQUEST) to *. **. ***. ***

    95 09:46:11.952 01/10/13 Sev = Info/6 IKE/0x6300003D

    Upon request of the DPD to *. **. ***. , our seq # = 107205278

    96 09:46:11.979 01/10/13 Sev = Info/5 IKE/0x6300002F

    Received packet of ISAKMP: peer = *. **. ***. ***

    97 09:46:11.979 01/10/13 Sev = Info/4 IKE / 0 x 63000014

    RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:dpd_ack)="" from="">

    98 09:46:11.979 01/10/13 Sev = Info/5 IKE / 0 x 63000040

    Receipt of DPO ACK to *. **. ***. seq # receipt = 107205278, seq # expected is 107205278

    ---------------------------------------------------------------------------------------------------------------

    Any help would be appreciated, thanks!

    try to refuse the ACL (access-list AnyConnect_Client_Local_Print extended deny ip any one) at the end of the ACL.

Maybe you are looking for

  • PXI-2510 has no reaction when using NI VeriStand

    Hi all I want to use a PXI-2510 in NI VeriStand and I read a document named NI VeriStand module - fault Insertion units OR to: http://zone.ni.com/devzone/cda/epd/p/id/6248 After deployment, I change my state of the controls in the workspace, but PXI-

  • Vista and Color Laserjet 5 M reprints all when the printer is turned on?

    Vist and Color Laserjet 5 M reprints all when the printer is turned on? It is a new one on me. I installed the printer with a barrette SIMM Postscript so it would work even at all under Vista and now it prints well but insists on the fact that I have

  • Key board error (Aspire 5920 G)

    I don't know what the problem is with some functions of the keys on my keyboard. Most of the time it works fine, but some (actually that bit) keys for some reason have changed their meaning. For example if I want to type ' @', I have to click shift +

  • Help to choose the upgrade memory for Aspire D270-1401

    I had difficulty pinning down the specification of an upgrade memory to 2 GB for my Aspire One D270-1401.  Can someone help me decide between PC3-12800 and PC3-8500.  It doesn't seem to be any help available for this model on the Acer site.

  • Disable the function of gloves

    I approved the extra sensitivity for gloves... Where can I disable IT?