After power failure screeen shows options to start normally, without failure, etc, but it won't start

Similar Questions

• WAG300N: could not start correctly after power failure

  Hello

  After AC power interruption, I tried to turn on my router Linksys WAG300N, but he won't start properly. I will describe what it looks like and what I've tried:

  I push the power button / stop, all 4 Ethernet LED simultaneous light for about a second, (if there is LAN cable connected, one or more led lights permanently) and power the LED will blink twice at normal speed. After that, both voltage and wireless, led simultaneously for about 1-2 seconds, start power LED flashes quickly, after seconds wireless LED stop light, wireless flash LED again and stop two LEDs for lighting. Second later power LED flashes two times normal speed and the process begins again but without flashing of the LED Ethernet (loop).

  I tried to download the firmware using TFTP, but it does not work. Router did not respond to a ping. After many tests, I noticed that the only time where I can ping router is during normal those two blinks of the power led. I've got 11 times waiting and the response of 1 or 2<1ms, 11="" timeouts,="" 1="" -="" 2="" responses etc... (response="" waiting="" time="" for="" a="" ping="">

  I've tried a few ways to reset the router (based on this forum). It does not help, sometimes after the reset I power the router problems or flashing process stops after a few loops (only one Ethernet LED lightning or router turns off). At the end of a day all supports them to the previous behavior of closure with power LED and wireless LED blinking.

  In the end, I tried utility upgrade Sercomm 2.07 mentioned in this topic: http://forums.linksys.com/linksys/board/message?board.id=DSL&thread.id=52

  This software detects only router after reset, when the router is in unknown mode, Internet and power LED flashes alternately.

  Software detects the device as MAC address and visualize correctly the version of firmware loaded into memory. Looks like it works and flashing memory. While flashing memory, power LED, LED Internet and Ethernet LED flashing at the same time very fast. I tried all versions of firmware available, but it does not help, I still have the same behave after flash.

  I think it could be a problem with the bootloader, maybe that part of the memory is broken, but I did not how to fix it. I found information on the JTAG interface, but I don't know if it will work for router WAG300N and where I can find the appropriate file with bootloader.

  Maybe someone can help and give me the idea what should I / check. Theoretically, I should have left 1 year warranty, but I lost the proof of purchase required for the RMA process. I can't find the place in Poland where professionals can help me, so I think that should do it myself with your help

  I think that's the problem with the power adapter... You should try a different power of the specification of the same card...

• I have problems to restart of Yosemite, after power failure during the new backup, and now HD is also blocked.

  I have problems to restart of Yosemite, after power failure during the new backup, and now HD is also blocked.

  I tried the holding of 'command-r' and 'option' to see if the problem can be resolved or try any boot from a boot disk, my old backup, USB function start - but after a slow long process it all just stops.

  There is software on my HD that I don't want to lose by simply reformatting the computer, because I am now in a different country, far from my house, which is another problem of the Apple Store, to reinstall my OS from Yosemite on the www.

  Hey AmnonMikeCohen,

  Thank you for being a part of the communities of Apple Support.

  I understand that your Mac is not start properly after the power went out.  Let's start with resetting the SMC and NVRAM on your Mac and see if he can start from there:

  Reset the management system (SCM) controller on your Mac.

  How to reset the NVRAM on your Mac.

  See you soon.

• root &#62; \system32/had.dll message after power failure.

  After power failure, I got the above message.  I tried to rebuild the CD system following the instructions Microsoft but still can't het PC to start.  Any ideas anyone?

  Thank you

  Since you didn't say what were these instructions, we do not know what you were doing!

  You need to start the recovery console, run chkdsk r, then /Rebuild. bootcfg The first part can be read here:

  http://www.icompute.info/System_restore_from_xp_cd.htm

  You will need to understand how your PC (you neglected to tell us the make, model and model number!) can boot from the CD-ROM. Then, run the Recovery Console. DO NOT ENTER THE INSTALLER! (If you do, you run the risk to wipe your entire disk clean!) Follow the indications of the above page and then stops after having successfully performed chkdsk/r. In other words, don't do the fixmbr part!

  Then, for the second part, read here:

  http://www.icompute.info/halldll_error.htm

  Restart the PC in the usual way (that is, start with the hard drive) and let us know if you are at the back of buisiness.

• HP 280 G1 (N9E78EA): Partition disappears after power failure, watch now unallocated

  Hello!
  I have a PC
  HP 280 i5 - 4590S G1 / 8 GB/500/DVD-RW/W10P + 7Pro64
  and
  Pro series SSD Plextor 128GB 2.5 "SATA SSD M6.
  
  Partition disappears after power failure, watch now unallocated.
  I tried to use TestDisk to see what was going on. After crossing the 'Analysis' command and deep research, but the partition disappears.
  Any suggestions on what I should do next?

  Your SSD have lost files due to the power failure system sudden. I suggest you run CHKDSK to fix this error. Also remember, if the data stored in your SSD are important to you, then first the software of raw data as WDR pro of stellar phoenix recovery and then apply diagnoses to repair.

• Lenovo IdeaCentre Q180 behavior after power failure

  Hello

  I need a computer that automatically restarts after a power failure.
  I find nothing on the IdeaCentre Q180 behavior in such a case.

  Did the reboot of the IdeaCentre Q180 himself after power failure or is it possible to activate this feature?

  This behavior is very important for my new system.

  Thank you for your response.

  Kind regards
  Theodoor

  Hi theodoor, welcome to the forums.

  I am not personally acquainted with the Q180, but I had a quick glance in the simulator of BIOS and I am sure that the service you're looking for is available in the BIOS.

  Please see the photo attached, (too big to post), it will open in the same window, so please click on your back button on the browser to return to this site.

• I plugged a Linksys router for my Hewlett Packard desktop computer, it shows that it is connected with great resistance, but it won't let me connect to the web.

  I connected the router to my computer desktop Hewlett Packard, it shows that it is connected with great resistance, but it won't let me connect to the web. I also have a mid/fi through Verizon set up on this computer, but I have recently installed Magi jack more and it uses far too much data for the MiFi. What should I do to fix this?

  Hello

  ·         What is the error message or the error code that you get when you try to connect to the Internet?

  ·         What is your Linksys router connected to an Internet service provider?

  ·         Were there any changes made to your computer until the problem occurred?

  ·         What version of the Windows operating system do you use?

  Click on the link below.

  http://Windows.Microsoft.com/en-in/Windows7/help/which-version-of-the-Windows-operating-system-am-i-running

  To solve the problem related to the Magic jack plu and MiFi Verizon:

  I suggest you to contact Magic jack support. See the link below.

  http://MagicJack.com/customercare.asp

  Contact Verizon support. See the link below.

  http://support.verizonwireless.com/CLC/

  Provide us additional information. So that we can help solve you the problem on your computer.

  Hope this information helps you.

• does not start after power failure

  Here is what the screen shows

  File\windows\system32\drivers\aswvmm.sys
  Status: 0xc000000d
  Info: windows has no bread because a crytical system driver is missing or damaged

  I cannot drive vista or files by e-mail and will put on a flash drive or disc thank you

  Hello

  See if that helps you.

  Do a Safe Mode system restore to before the problem started.

  http://bertk.MVPs.org/html/restoresysv.html

  How to access Safe Mode

  http://www.bleepingcomputer.com/tutorials/how-to-start-Windows-in-safe-mode/#Vista

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  If it doesn't, try a startup repair and / or a system restore using a DVD of Vista from Microsoft

  Manufacturers recovery disks normally do not have Service Options; they are normally a relocation to the factory only settings option.

  Here is the guide to repair Options using a Vista DVD from Microsoft.

  If a friend or a work acquantance of yours has one, you can borrow and use it for repairs.

  http://www.bleepingcomputer.com/tutorials/repair-Windows-with-Windows-Startup-Repair/

  Table of contents

  1. Overview of Windows Vista repair options
  2. How to perform an automatic repair of Windows Vista using Startup Repair
  3. Advanced Tools Overview
  4. Conclusion

  If you do not or can not borrow a Microsoft DVD there is a download of a file ISO of Vista Startup Repair available that you can put on a Bootable floppy to make the above startup repair and that the method is recommended by a large number of posters in these Forums.

  Unfortunately, you have to buy it.

  Here is a link to it:

  http://NeoSmart.net/blog/2011/Windows-Recovery-discs-updated-reinstated/

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  There are several methods to reinstall Vista.

  This can help you (download files and make your own DVDs).

  Vista ultimate is available. Read the information in the lower part of the message on how to use it for other editions of Vista:

  http://www.heidoc.NET/Joomla/technology-science/Microsoft/57-Windows-Vista-direct-download-links

  And here are instructions on how to burn ISO disk images:

  http://www.SnapFiles.com/get/isorecorder.html

  The download links and information on how to make the ISO file, and then create the Setup DVD above are at this link:

  "How to download a Vista ISO and create a Setup DVD or USB"

  http://www.Vistax64.com/tutorials/301852-Vista-ISO-download-create-installation-DVD-USB.html

  "How to create a USB of Vista Installation key '

  http://www.Vistax64.com/tutorials/181538-USB-bootable-Vista-installation-Flash-thumb-drive.html

  ___________________________________

  You can contact your computer manufacturer and ask them to send you a set of recovery disks.

  They should do this for a small fee.

  To reinstall Vista using their recovery disk/s, you start from the 1st recovery disk they provide and follow the manufacturer's instructions to reinstall:

  You need to change the Boot order to make the DVD/CD drive 1st in the boot order:

  How to change the Boot order in BIOS:

  http://pcsupport.about.com/od/fixtheproblem/SS/bootorderchange.htm

  "How to replace Microsoft software or hardware, order service packs and replace product manuals.

  http://support.Microsoft.com/kb/326246

  ___________________________________

  And if you have never received a recovery disk when you bought your computer, there should be a recovery on the drive Partition hard reinstall Windows how much you bought your computer.

  The recovery process can be started by pressing a particular combination of the key or keys at startup. (Power on / start)

  Maybe it's F10, F11, Alt + F10, etc., depending on the manufacturer.

  Them or us ask the right sequence of key.

  ___________________________________

  Most manufacturers have more available Vista recovery disks, but you may be lucky with your manufacturer.

  If this happens, you may need to try this instead:

  You can also borrow and use a Microsoft Vista DVD, which contains the files for the different editions of Vista (Home Basic, Home Premium, Business and Ultimate) must be installed. The product key on your computer / Laptop box determines what Edition is installed.

  Other manufacturers recovery DVDs are should not be used for this purpose.

  And you need to know the version of 'bit' for Vista, as 32-bit and 64-bit editions come on different DVDs

  Here's how to do a clean install of Vista using a DVD of Vista from Microsoft:

  "How to do a clean install and configure with a full Version of Vista '

  http://www.Vistax64.com/tutorials/117366-clean-install-full-version-Vista.html

  And once the operating system is installed, go to your computer manufacturer's website and get the latest drivers for your particular model or laptop computer.

  And phone Activation may be necessary when you use the above installation method.

  "How to activate Vista normally and by Activation of the phone '

  http://www.Vistax64.com/tutorials/84488-activate-Vista-phone.html

  See you soon.

• VMTMS not showing running, not installed, VM TCS after power failure by giving two fake ips

  Nice day

  In fact, we had a power failure at our DC and after restarting servers, 2 of them you have the problem.

  UCS after the beginning of the VMTMS v 14.4.2 showing in summary "does not installed ' and no Ping able.but I can access Internet by IP however.

  TCS giving 2 Fake ips also.

  TCS.jpg

  

  I just checked our vTCS, it shows only a single IP address.  If the server has more than one virtual nicinstalled, you can probably remove the sound that shouldn't be there.  Although I'm not a VMWare administrator, so I can't say for sure, comparing what has my TCS.

  Note: Your question would be better in the telepresence of the forums section, where these devices are discussed more actively and people can help you get the answers you need.  You can move your question to the appropriate section by editing and modifying the categories at the bottom.

• Windows XP SP3 does not start after power failure

  I've known a sequence of power failure while my computer was on. When the power was restored, I couldn't boot into Windows. Windows stops before loading the Welcome screen and hangs. I tried in "Safe Mode" and "Restore Point", but always impossible to load up to 'user account screen '. I am running XP SP3.

  I tried recovery of original windows CD. No joy. I ran chkdsk with the option/r several times and fixboot as well, without success. Help, please!

  Just type fixmbr at the command prompt in Recovery Console.

  For more details, see http://www.microsoft.com/resources/documentation/windows/xp/all/proddocs/en-us/bootcons_fixmbr.mspx?mfr=true

  Also http://helpdeskgeek.com/how-to/fix-mbr-xp-vista/

• Reference Dell R710 does not start after power failure

  Hello, I tried to find answers on the forum but nothing so far

  I have this R710 at home that I use as a media server, it was working fine before a power outage the other night (no I don't have a UPS :-(

  When the power returned, I noticed one of lighting power supply has been turned off, so I took it out of the unit, but the unit still won't turn.

  I still have a so-called good food because the small green LED on the motherboard lights, and I can access the iDRAC, this feature, I didn't before the net Searchin' for answers, I'm kind of a novice with the servers.

  When I access the iDRAC, on the power supply page, I see nothing, no power supply listed.

  Is it possible that a diet might be "half bad", enough to work the emergency circuits but not the power outlet?

  Symptoms:

  Camera lights.

  Can access the functions of the Idrac, but doesn't do anything if I try to activate it via the tasks "quick launch".

  Power supplies are not visible on the pages of the Idrac.

  Display before work.

  Server was very well just before a power failure which took one of the PSU

  The remaining 870 PSU has the green light on, and the fan works for 2 seconds every time I cut the power it.

  Thanks for any help.

  OK, well... no answers.

  I found a place locally that sold a diet so I arrived with my server, I told them I would buy the power supply that I confirm that the fault was in fact the power supply.

  Well, you know, the unit started correctly with the new power supply, now in IDRAC, I see both power supplies but on that faulty, he reads "present, entry lost.

  So the answer is YES, a power supply may be defective, even if the green light is on.

• UEFI auto turn on after power failure

  I bought a desktop computer HP Pavillion PC500-225es (have a holiday home in Spain where the suffix are).

  It is running Windows 8.1 equipped a UEFI BIOS.

  I want the PC automatically restarts when power is restored after a power failure, but I don't see any option to do this in the UEFI BIOS. Is it normal for a UEFI BIOS? I have had many computers with a BIOS for old style and that I can remember all had the ability to set the auto restart after power fail.

  I don't know how a UEFI BIOS integrates with Windows 8.1 but I see no option for this in point 8.1 of Windows either.

  Someone at - it ideas?

  In addition, because the PC was bought in Spain, the BIOS is in Spanish. It seems not be anyway to change that in English, my native language. Not a big problem I can get in Spanish and may apply to the Google translate if I have to, but it would be easier if there was an option to switch to English.

  I ran the HP Support Assistant, and everything is up-to-date, there is no update to download BIOS.

  I guess I'm just stuck with the situation unless HP come with an update of the BIOS to add installation.

  Please see the BIOS for the motherboard Jasmine settings the settings you are looking for. Although this document is intended for the 'Jasmine' motherboard and your computer uses the "JasmineR', the settings should be similar if not the same thing.

  To access the BIOS Setup page... "Turn on the computer and immediately press the F10 key repeatedly, once per second, until the opening of the Computer Configuration utility."

  The following options are found in the Power Options:

  Messages POST (Power On Self Test)	Turn on or off
  After the loss of power	Previous state, or disable
  POSITION of delay (in seconds)	Zero, 5, 10, 15, 20 or 60 seconds

  If you have any other questions, feel free to ask.

  Please click the 'Thumbs Up' white LAURELS to show your appreciation

• How to wake up a T42 - after power failure.

  I just changed to a T42 as a home automation web application server in a vacation home that is unoccupied for weeks and months.  I'm gone with a Thinkpad retired because the processor running at 40 degrees Centrigrade with its fan-Off in our cool basement unless there is some computer activity... hoping the Thinkpad would unnattended for years in this quiet situation with the HDD as the only moving part.

  When the power goes out, I have an inverter for 2 hours, plus the Thinkpad battery for 4-5 hours (off screen), but then it stops with an extended power failure.  We cannot go back to this place for months to re - turn on the computer.

  The bios settings on T42 for "Startup Timed" do not work for me or anyone else I saw on the Thinkpad forums.

  Or, using the Task Scheduler with the "wake the computer" option when you run an application (such as the calculator or Notepad) do not wake the T42 from sleep mode. (The laptop could go to sleep when the battery reaches 50%)... then having the scheduler run Notepad all morning at the cases where the computer is in standby due to a power failure in the course of 24 hours prior... but it does not work.

  Is there another way to start or wake a T42 on a calendar or a network drive?   I didn't "want to solder connections in the power switch - although if it is possible if I could use a phone remote access to the automation system to turn on the computer with a closing contact, but his disorder at."

  After testing, I switch to Windows 7 Pro. The T42 can going mode sleep after x minutes on battery. It can be awakened by running a lazy batch file by using the Windows Task Scheduler.

  Thanks for your suggestion

• Fans always operate at high speed after power failure

  HP Pavilion Slimline S5780T - Windows 7 Home Premium 64-bit

  After a power failure a night or more recent, our Pavilion Slimline case fan and CPU fan have both run at high speed all the time, starting from the system. The level of noise is intolerable.

  I opened and cleaned all the dust from the inside of the case, including the removal of the heatsink from the CPU. Everything is clean.

  I ran the following HP Vision diagnostic, test the system, including fans. During the test of fan, the fans ran at 100%, then fell to the former level normal, quiet, then ramp back up to 100%. So says HP fans diagnostic tests are OK when there is always a problem. And it is possible for them to run at slow, normal speed.

  I installed the free SpeedFan utility, but there is not place to adjust the fan speed manually.

  How can I find the problem and the fans run at normal speed, as they did before the power failure? Everything that controls the speed of the CPU fan and the fan is broken.

  Thank you and best regards,

  Stephen - Myrtle Beach, SC

  Strange things happen when power flucuations or failures occur.  Most probably the motherboard has been damaged by the PPE and that is normally not as repairable by a DIY.  If you could find a newer BIOS, that to solve the problem.  Since there can be no more recent BIOS, try to remove the battery from the motherboard for the night and then put the file in and reset the BIOS to see if that helps the default value.  Otherwise, it might be repairable.

• ReadyNAS 104 unable to boot after power failure

  Hello

  My Readynas 104 unit is in a suspended state. Power blue led continues to blink (for hours) when I restarted after a power failure. The disply screen says "READYNAS 6.4.0" and no button works. I can only remove the power cable and connect back to try again to start, but even once, he ends up in the same State of the Power LED flashes continuously.

  Device answering queries ping but actions / iSCSI and admin page not available.

  Someone of you has faced this kind of problem or can help me solve this problem without losing any data please?

  Thank you

  Hussain

  I want to contact support.