How to wake up a T42 - after power failure.

Similar Questions

• 2135 Deskjet ink advantage: how to resume two-sided printing after power failure

  I was doing a face print job two. at halfway, there was failure, now I want to resume my print job where it was left. How to do?

  Hi @kapilguj,

  Welcome to the HP Forums!

  I see you're wondering how to resume printing duplex after a loss of powere, with your printer HP Deskjet Ink Advantage 2135. I'm happy to help you!

  You will have to start the print job because there is no way out of the where you left off with this printer.

  If this, or one of the posts on this thread, helped you to solve the problem, please click 'Accept as Solution' said post. To show you 'like', or that they are grateful for my post, please click the thumbs upwards below. If there is anything else I can do to help, please don't forget to let me know!

  Hope that answers your question and have a nice day!

• I have problems to restart of Yosemite, after power failure during the new backup, and now HD is also blocked.

  I have problems to restart of Yosemite, after power failure during the new backup, and now HD is also blocked.

  I tried the holding of 'command-r' and 'option' to see if the problem can be resolved or try any boot from a boot disk, my old backup, USB function start - but after a slow long process it all just stops.

  There is software on my HD that I don't want to lose by simply reformatting the computer, because I am now in a different country, far from my house, which is another problem of the Apple Store, to reinstall my OS from Yosemite on the www.

  Hey AmnonMikeCohen,

  Thank you for being a part of the communities of Apple Support.

  I understand that your Mac is not start properly after the power went out.  Let's start with resetting the SMC and NVRAM on your Mac and see if he can start from there:

  Reset the management system (SCM) controller on your Mac.

  How to reset the NVRAM on your Mac.

  See you soon.

• root > \system32/had.dll message after power failure.

  After power failure, I got the above message.  I tried to rebuild the CD system following the instructions Microsoft but still can't het PC to start.  Any ideas anyone?

  Thank you

  Since you didn't say what were these instructions, we do not know what you were doing!

  You need to start the recovery console, run chkdsk r, then /Rebuild. bootcfg The first part can be read here:

  http://www.icompute.info/System_restore_from_xp_cd.htm

  You will need to understand how your PC (you neglected to tell us the make, model and model number!) can boot from the CD-ROM. Then, run the Recovery Console. DO NOT ENTER THE INSTALLER! (If you do, you run the risk to wipe your entire disk clean!) Follow the indications of the above page and then stops after having successfully performed chkdsk/r. In other words, don't do the fixmbr part!

  Then, for the second part, read here:

  http://www.icompute.info/halldll_error.htm

  Restart the PC in the usual way (that is, start with the hard drive) and let us know if you are at the back of buisiness.

• HP 280 G1 (N9E78EA): Partition disappears after power failure, watch now unallocated

  Hello!
  I have a PC
  HP 280 i5 - 4590S G1 / 8 GB/500/DVD-RW/W10P + 7Pro64
  and
  Pro series SSD Plextor 128GB 2.5 "SATA SSD M6.
  
  Partition disappears after power failure, watch now unallocated.
  I tried to use TestDisk to see what was going on. After crossing the 'Analysis' command and deep research, but the partition disappears.
  Any suggestions on what I should do next?

  Your SSD have lost files due to the power failure system sudden. I suggest you run CHKDSK to fix this error. Also remember, if the data stored in your SSD are important to you, then first the software of raw data as WDR pro of stellar phoenix recovery and then apply diagnoses to repair.

• Lenovo IdeaCentre Q180 behavior after power failure

  Hello

  I need a computer that automatically restarts after a power failure.
  I find nothing on the IdeaCentre Q180 behavior in such a case.

  Did the reboot of the IdeaCentre Q180 himself after power failure or is it possible to activate this feature?

  This behavior is very important for my new system.

  Thank you for your response.

  Kind regards
  Theodoor

  Hi theodoor, welcome to the forums.

  I am not personally acquainted with the Q180, but I had a quick glance in the simulator of BIOS and I am sure that the service you're looking for is available in the BIOS.

  Please see the photo attached, (too big to post), it will open in the same window, so please click on your back button on the browser to return to this site.

• Fans always operate at high speed after power failure

  HP Pavilion Slimline S5780T - Windows 7 Home Premium 64-bit

  After a power failure a night or more recent, our Pavilion Slimline case fan and CPU fan have both run at high speed all the time, starting from the system. The level of noise is intolerable.

  I opened and cleaned all the dust from the inside of the case, including the removal of the heatsink from the CPU. Everything is clean.

  I ran the following HP Vision diagnostic, test the system, including fans. During the test of fan, the fans ran at 100%, then fell to the former level normal, quiet, then ramp back up to 100%. So says HP fans diagnostic tests are OK when there is always a problem. And it is possible for them to run at slow, normal speed.

  I installed the free SpeedFan utility, but there is not place to adjust the fan speed manually.

  How can I find the problem and the fans run at normal speed, as they did before the power failure? Everything that controls the speed of the CPU fan and the fan is broken.

  Thank you and best regards,

  Stephen - Myrtle Beach, SC

  Strange things happen when power flucuations or failures occur.  Most probably the motherboard has been damaged by the PPE and that is normally not as repairable by a DIY.  If you could find a newer BIOS, that to solve the problem.  Since there can be no more recent BIOS, try to remove the battery from the motherboard for the night and then put the file in and reset the BIOS to see if that helps the default value.  Otherwise, it might be repairable.

• UEFI auto turn on after power failure

  I bought a desktop computer HP Pavillion PC500-225es (have a holiday home in Spain where the suffix are).

  It is running Windows 8.1 equipped a UEFI BIOS.

  I want the PC automatically restarts when power is restored after a power failure, but I don't see any option to do this in the UEFI BIOS. Is it normal for a UEFI BIOS? I have had many computers with a BIOS for old style and that I can remember all had the ability to set the auto restart after power fail.

  I don't know how a UEFI BIOS integrates with Windows 8.1 but I see no option for this in point 8.1 of Windows either.

  Someone at - it ideas?

  In addition, because the PC was bought in Spain, the BIOS is in Spanish. It seems not be anyway to change that in English, my native language. Not a big problem I can get in Spanish and may apply to the Google translate if I have to, but it would be easier if there was an option to switch to English.

  I ran the HP Support Assistant, and everything is up-to-date, there is no update to download BIOS.

  I guess I'm just stuck with the situation unless HP come with an update of the BIOS to add installation.

  Please see the BIOS for the motherboard Jasmine settings the settings you are looking for. Although this document is intended for the 'Jasmine' motherboard and your computer uses the "JasmineR', the settings should be similar if not the same thing.

  To access the BIOS Setup page... "Turn on the computer and immediately press the F10 key repeatedly, once per second, until the opening of the Computer Configuration utility."

  The following options are found in the Power Options:

  Messages POST (Power On Self Test)	Turn on or off
  After the loss of power	Previous state, or disable
  POSITION of delay (in seconds)	Zero, 5, 10, 15, 20 or 60 seconds

  If you have any other questions, feel free to ask.

  Please click the 'Thumbs Up' white LAURELS to show your appreciation

• Cannot take possession of the two machines after power failure

  Greetings...  Recently, I experienced a power failure to my office when I was running two different virtual machines.  After the reboot, I am unable to connect to machines like VMWare tells me "this virutal machine seems to be running."  If I press the button "Take Ownership", he immediantely is back with a dialog box saying "Appropriation of this virtual machine failed."  How to unlock these machines?

  Thanks in advance

  Jason

  Hello

  First stop of VMware Workstation, then go and have a look at the folders where are stored the your virtual machines.

  It is likely that you will see some .lck .lock files or folders. Which ones you will see (lck or lock) depends on the version of your VMware product.

  Delete these files (move them to another folder if you are more comfortable with it), and then return to VMware Workstation.

  Reopen the virtual machines and chances are big enough to make them work as they used to be.

  Good luck!

  --

  Wil

• GSM7224v2 loses the configuration after power failure

  As the topic title says - this device (new for me but flea market) loses its configuration after power off.

  I don't see any button cell within the unit for volatile memory backup. Surely the configuration lives in non-volatile storage?

  I am being dumb and I'm missing something?

  Hi neidlo

  Welcome to the community!

  Yes configuration lives in a non-volatile memory, when it is saved. Until it is saved, it is in RAM.

  When configuring the switch, it is not automatically saved. Using Web Interface (GUI)? A "Save" button should do.

  Please let us know whether or not this was the burden

  Kind regards

• ReadyNAS 104 unable to boot after power failure

  Hello

  My Readynas 104 unit is in a suspended state. Power blue led continues to blink (for hours) when I restarted after a power failure. The disply screen says "READYNAS 6.4.0" and no button works. I can only remove the power cable and connect back to try again to start, but even once, he ends up in the same State of the Power LED flashes continuously.

  Device answering queries ping but actions / iSCSI and admin page not available.

  Someone of you has faced this kind of problem or can help me solve this problem without losing any data please?

  Thank you

  Hussain

  I want to contact support.

• Windows XP SP3 does not start after power failure

  I've known a sequence of power failure while my computer was on. When the power was restored, I couldn't boot into Windows. Windows stops before loading the Welcome screen and hangs. I tried in "Safe Mode" and "Restore Point", but always impossible to load up to 'user account screen '. I am running XP SP3.

  I tried recovery of original windows CD. No joy. I ran chkdsk with the option/r several times and fixboot as well, without success. Help, please!

  Just type fixmbr at the command prompt in Recovery Console.

  For more details, see http://www.microsoft.com/resources/documentation/windows/xp/all/proddocs/en-us/bootcons_fixmbr.mspx?mfr=true

  Also http://helpdeskgeek.com/how-to/fix-mbr-xp-vista/

• After power failure screeen shows options to start normally, without failure, etc, but it won't start

  When you enter to start either or all of the above, the display returns to show the same options.

  Hello

  ·         Apart from these options, meet you any other error message?

  ·         What were you doing before the power failure? Have install you the updates or programs on the system?

  Method 1:

  I suggest you to disconnect all external devices (except the monitor, keyboard and mouse) that are connected to the system and restart and check.

  Method 2:

  I suggest you follow the steps mentioned in the article below.

  How do I recover from a corrupted registry that prevents Windows XP startup

  http://support.Microsoft.com/kb/307545

• laptop local disk & CD-ROM drives have failed after power failure

  power failure caused failure of local disk & corrupted CD-ROM on toshiba L305D-S897 running Windows/vista home Prem how, I can't on the local disk & I can't use the (disk) backup, because the operating system cannot find the CD, & every new driver I install corrupted becumes! What is my next step? Thank you!

  Hi Dr. truth,

  This seems to be a hardware failure. You must get in touch with Toshiba to get help.

  Toshiba support

  http://forums.Toshiba.com/

• ONS 15454 presents itself as 'unknown' after power failure

  We had a power failure that also landed an ONS 15454 in a remote installation. To restore power and power on the device, it appears in the CTC under gray with "Uknown2" as the name.

  I had someone reinsert the card of STC, but sometimes still unknown.

  Has anyone seen this? Suggestions (the unit is hours from me)

  Try to restart the session from the CTC and clear the cache of the CTC

  You can test the node

  Checks whether the node is in the OSPF routing table

  You can access through the CTC locally

  Your CTC terminal is directly connected, or does it go through a firewall

  Probably resolved now how did you solve it?