After standby mode Satellite L300 cannot connect to the internet

Similar Questions

• Unwanted automatic reactivation of the Mode standby mode when it is connected to the Internet

  I have a relatively new home office Pavilion model p6140F, product number NP192AA, version number software 93NAv6PrA2.  Factory installed operating system is Windows Vista Edition Home Premium, 64-bit, Service Pack 2.  I am connected to the internet via a cable modem.  I made energy-saving settings for automatic sleep mode sleep.  Quite often the computer comes out of fashion "sleep" on its own.  What is strange to me, is that when this happens and I click the Start button at bottom left of the screen or any buttons on the Quick Launch bar, nothing happens on the first click.  Only on the second click the computer is what I normally wait until it gets when clicking on the Start button or the quick launch of the first time button.  I tried an experiment by disconnecting the internet cable from the computer modem and the computer behaves as I expect.  He remains in the mode "Eve" from one day to the next day when I unplugged the internet overnight.  It looks like something 'out there' on the internet is somehow take control of the computer, do not let it go in the mode 'sleep' and play with use and function of the 'Start' buttons and the quick launch area.  At the very least, it's embarrassing, if not malicious.  Is occurring with other users?  Wouldn't be some 'normal' functioning of monitoring by HP, Microsoft, providers of security software that I have permission, or is this behavior that should not be expected.  Thanks for any direction on the techniques of 'analysis' on mine could give clues at the origin of this strange behavior.

  Bad Board.  Marking as resolved.

• Satellite C660 cannot connect to the internet

  I am a total novice when it comes to these things.

  I recently installed Windows 7 32 out of a recovery disk, my friend did for me from the Microsoft Web site. Now, I can not connect to the internet.

  There is a small box with a red criss who says "no connection is available" and when I troubleshoot it says I need to install a driver for my network card.

  In Device Manager, it has the yellow! in other devices, next to Ethernet controller, network controller, controller of communication simple PCI and unknown device. I tried to connect my wireless adapter that I use on my main to pick up WiFi, computer, but that no longer works.

  Also, I went to the section Toshiba drivers and tried a few drivers but none seemed to work.

  Can someone tell me please exactly which driver I need to download to my computer with WiFi?

  Thanks :)

  > Can someone please tell me exactly which driver I need to download to my computer with WiFi?
  We can help you with this, but please exact notebook model poster and the name of the template to verify the hardware configuration and find out what WLAN card is inside.

  By the way: if I understand you is good you have preinstalled version of the OS and not the recovery image, on the right?

• Satellite L500 cannot connect to the internet

  I just bought a new Toshiba L500
  I have a NETGEAR router that works on my other laptop, desktop and IPHONE, but it does not work on my Toshiba L500.

  I can't find the NETGEAR router using the icon in the lower right corner but when I login I get this message error "Windows could not connect to netgear.

  Does anyone have a solution to this problem?

  Hey,.

  Do you have an IP address of your router and have you tried a static IP address?

  Also, check your firewall settings. Maybe the firewall is blocking the connection to your router.
  In addition, an update of the firmware on your router is always advisable. :)

• Programs cannot connect to the internet, while IE8 and firefox work very well on the internet.

  I used google chrome as my default browser, but one day it stopped working, while firefox and IE always worked / work fine now.  When google chrome no longer works, all my programs stopped to connect to internet, like Skype, itunes, WMP, etc.  The itunes gives error me is "make sure that your network connection is active and try again.  When I download programs through to firefox or IE8, now my default, they download but used to install or connect to the internet (I tried to reinstall chrome after that deletion but it will not be completed).  I was certain this isn't the router or the Internet itself, my wireless works very well to navigate through the Internet and other computers on the network do not have this problem. problem when I connect to other wifi networks.  The help and support center will not be to the point after that I click on it.  I use windows xp sp3 home edition 2002.  I looked through the other threads to see if I can solve the problem, check the exceptions in the firewall, disabling firewalls and other security, running an antispyware/malware, someone suggested (super antispyware), lowered or disabled security settings, but all without success.  I don't know what to do at this point but to restart the system.  Please help, any suggestions?  Thanks in advance.

  Hi unlucky2013,

  Follow the steps from the link below: Windows XP Internet programs cannot connect to the Internet through the connection broadband:http://support.microsoft.com/kb/307164

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Windows cannot connect to the Internet using HTTP, HTTPS or FTP. __This is probably caused by settings of firewall on this computer. __

  I recently installed the version of Norton, after that I was unable to use the internet, I thought it was the Norton firewall settings. After having playing with her for 30 minutes, I gave up and uninstalled Norton. I have disabled the firewall, I have reset the default settings. Here is the message I get when I run a diagnostic. A crazy thing is that I can connect to internet when I connected to this same computer as a guess.

  Please help me!

  Windows cannot connect to the Internet using HTTP, HTTPS or FTP.
  This is probably caused by the settings of firewall on this computer.

  Check the settings of firewall for the HTTP port (80), HTTPS port (443) and FTP port (21).

  Hi rhonda9937,

  1. what browser you are using to connect to the internet?

  It is not recommended to keep Windows Firewall disabled on the computer.

  This would happen if the ports are not open in the Windows Firewall.

  I suggest that you open ports in Windows Firewall and check if it works.

  How to manually open ports in Internet Connection Firewall in Windows XP

  http://support.Microsoft.com/kb/308127

  Troubleshooting settings of Windows Firewall in Windows XP Service Pack 2 for advanced users

  http://support.Microsoft.com/kb/875357

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• WAG-120N and static ip - wireless and wired clients cannot connect to the internet

  Greetings,

  I use the N WAG-120 AP and switch for 3 computers laptops and 2 Office. Our Department is assigned only a what IP static of our server, as well as a pc can connect to the server and the internet. I use the first lan port of the 120N Wag as a WAN port and I attribute the static IP address, and the subnet, default gateway, and DNS addresses. Connected clients receive an ip address from the DHCP (192.168.1.10x) router, but cannot connect to the internet. How can I configure my router to allow clients to connect?

  Thank you in advance!

  The default LAN IP of the WAG subnet is 192.168.1.0/255.255.255.0 belongs to 192.168.0.0/255.255.0.0. This means that 192.168.1.0 IP addresses exist side WAN and LAN of the WAG. What makes this configuration completely cannot be routed.

  Change the address LAN IP of the WAG to an IP outside the corporate network, for example using IP addresses private 172.16/12, for example to set the address LAN IP 172.16.1.1 with 255.255.255.0 subnet mask.

  The alternative would be to use the WAG as a point of easy access only, and not as a router. However, due to the 255.255.0.0 subnet in your network company you will not be able to access the web interface except from an IP address corresponding to the LAN IP address subnet of the WAG. Of course, this does not affect the wireless or wireline customers connected to the WAG...

• My computer cannot connect to the internet, the signal is excellent in the modem, but the computer does not recognize that there is a link.

  My computer cannot connect to the internet, the signal is excellent in the modem, but the computer does not recognize that there is a link. What could be wrong?

  Hello

  • What connection do you use?
  • What is a wired or wireless?
  • What happens when you try to start Internet Explorer?
  • You receive an error message?

  You can check these links:

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  http://support.Microsoft.com/kb/956196

  Warning: Reset the Internet Explorer settings can reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings

• WRT54GL establishment cannot connect to the Internet

  I'm so basic in my problem as I feel stupid, but I get the message that the router cannot connect to the Internet.  Why the hell not?  I am writing on the same laptop, using the same ADSL modem and Internet connection.  So why don't the router sees it?  The last time I have tried again, start over from scratch, he kept do and re-do "check your computer's connections" and then ask me again my password of.  I didn't know if he wanted the original preset 'admin' or that I had sometimes back (hours) came the first time that this has been asked.  So I tried both.  Finally he moved reset the password or something, and I finally return to the "the router cannot connect to the Internet.  Power, then turn on the DSL Modem. "I did already too many times to count.  And again I say, this direct DSL connection of the modem for my laptop is fine.  But when the cable Internet through the router, then the other wire goes to my laptop, no Internet.  All the time my DSL modem displays a green light for the Internet.  And the router shows a light on the Internet.

  I'm too tired to walk any further tonight.  Maybe someone has a simple suggestion.  I'll check tomorrow.

  Thanks for helping this rank amateur.

  Try to configure the router manually.

  Connect the modem to the Internet port and the computer and port Ethernet 1 of the router.

  Press and hold the reset button on the router for 30 seconds. Release the reset button and wait 30 seconds. Power cycle the router and reconfigure.

  Follow this link to configure the router with DSL Internet Service.

• My laptop cannot connect to the internet with the error (code 31) Qualcomm Atheros AR9485WB-EG Wireless Network Adapter

  Hi, my laptop have this problem cannot connect to the internet, but the bar shows that I am connected to the network, but without access to the internet.

  I tried someone's guide to uninstall the network adapter in Device Manager and then reinstall it again, but now I'm stuck with the laptop cannot even detect the wireless network and the "Qualcomm Atheros AR9485WB-EG Wireless Network Adapter ' on Device Manager displays this message"the device is not working properly because Windows cannot load the drivers required for this device. (Code 31)"

  I forgot since when this problem persists.

  Please help me with this problem of internet connection,

  List of maybe / don't may not be the problem:

  1. I had mcafee antivirus 3 weeks around which has already expired for about 50 days and I uninstalled to turn into kaspersky anti-virus

  2. my windows is still 8.0

  3 ASUS N56V

  4. browser chrome incognito window

  Thank you Mr President, I found a solution for this problem

  I just turn on the download via connections counters my PC-> devices config->download via connections counters

  and then I tried to enter the following command at the command prompt run as administrator

  netsh int ip reset c:\resetlog.txt

  I hope this helps anyone else having the same problem as mine

  Thank you again Sir

• I had Acrobat Pro 8.3 for awhile. It is a registered product. However, as I updated to Windows 10, repeat me that it cannot connect to the internet to register or update the product

  I had Acrobat Pro 8.3 for awhile. It is a registered product. However, given that I have updated to Windows 10, he repeats that it cannot connect to the internet to register or update the product. I am connected to the Internet. What should I do?

  Thank you

  Reinstallation of my original DVD has solved the problem.

  Charlie

• After the HP update cannot connect to the Internet using my ISP wireless

  I have a HP Pavillion15 Notebook PC, Prod #: E7C83AV using Windows 8. Hp yesterday made an update, and subsequently, my computer does not connect to the Internet, using the same network wireless ISP.  Only way I can get Internet is to use the DSL unit to the computer USB cord.  I had a "Configuration for Invalid IP (106)"

  My ISP is still in my system with the same password, and I can't find any reason why it does not connect.  I have all the correct lights on my computer & the DSL unit.  I have not contacted my ISP, do not know what to say "After HP did an update, your service will not work?"

  Tonight I tried to get help from HP, big whoopie, even when I'm in warranty for 9 months, I was transferred to HP/SmartFriends, who told me that I had to pay for the assistance.  It won't happen!

  I don't know what to do now, I'm not very computer savvy and if HP won't help, do not know where to turn now.

  I'm fighting mad now!

  Someone please help.

  Have you tried to restore to previous work image?

• After upgrade from Vista to Windows 7 Ultimate home, no problem connecting to the internet when logged as an administrator, but cannot connect to the internet using the standard account. How to fix this?

  After upgrade from Vista to Windows 7 Ultimate home, no problem connecting to the internet when logged in as an administrator,

  but unable to connect to the internet using the standard account.  I have the latest version of the Solution Explorer.

  How to fix this?

  Glad to hear it.

  If the problem is resolved, mark the message as response, then it'll be useful for people with similar/identical problem.

• iPhone cannot connect to the Internet via time capsule

  I have a current execution capsule 7.7.7 time. IPhones in my house can't get internet service when it is connected to the time capsule. My iPad, I tap on it now, can get internet time capsule service. My Mac can connect. I restarted the capsule of time with my modem cable many times. My passwords are correct.

  I also have a smart Vizio TV that does not connect to the Internet. This is true with wifi and also with a wired connection to the time capsule.

  I don't know what the cause of the problem. Any help will be appreciated.

  He has worked in the past and now could not or never worked?

  Apple routers can sometimes decide autonomously switch to bridge mode. If your cable modem is not a router, you MUST have the apple router... TC in your case DHCP and NAT mode.

  If you have not done before you reset the TC at the factory and re-do the installation. Here are my recommendations.

  Universal factory reset

  Turning off the TC... That is, remove the power supply cord or the power at the wall outlet, wait 10 seconds... Hold the reset button... be nice... Turn on always even now in reset... and keep holding in for another 10 seconds. You may need assistance because it is difficult to hold in reset and power on. It will show the success quickly flashing led front. Release reset... and wait a few minutes for the TC to reset and return with the factory settings. If the front LED flashes quickly you missed and simply try again. The reset is quite fragile in these... Press the key while it is just click away and not more... I've seen people bend lever or even break. I use a toothpick as a tool.

  NB. None of your files on the hard drive of the TC are removed... This simply clears the settings of the router of the TC.

  The installer the TC.

  Then redo the configuration of the computer that you want to use for TM using Airport utility.

  1. the use of very short names... NO APPLE RECOMMENDED names. Without the space and pure alphanumeric characters.

  for example TCgen5 for the base station and the name of the TCwifi wireless.

  If the wireless is still an issue defined wireless names like TC24ghz and assigned the 5 GHz other name... eg.TC5ghz.

  Finally, use fixed channels in 2.4 ghz... try 11, 9 and 6, in that order.

  (leave the security for a few minutes and see if that makes a difference).

  For iphone and TV with problems in your Setup program ensure that the TC is NAT and DHCP... try to use a different such as google public DNS 8.8.8.8 and 8.8.4.4

  2. use all passwords also consistent with 1. but maybe a little longer. IE 8 and 20 characters of mixed cases and numbers... no alphanumeric non-caracteres.

  ** 3. If the TC is router, you can ignore this point. It is only a problem when the TC is bridged.

  If ensure that the TC is always the same IP address... you will need to do this on the main router using a dhcp reservation... or a bit more complex setup by using the static IP address in the TC.

  Ignore this point if you don't understand it... after the return if you drop questions.

  4. be sure that IPv6 is set correctly in the computer. IE link-local only for ethernet or wireless depending on whether you are using. Car is not good enough.

  Tell us which modem cable, you have, make and model please?

  The TC has problems with some popular brands... one of the SB series a modem port is malfunctioning.

• HP Envy 4500: Printer says it has solid network connection, but cannot connect to the internet

  So I have not been able to use my printer wireless lately, so I decided to check if it was connected to my wireless network. It is; I checked, re-connected and checked several times. So I decided to reactivate my web services. I have them turned off, and now whenever I press the button on the printer ePrint, it says connection for a really long time and then displays the message in the sense of "the printer cannot connect to the server. Check the internet connection and proxy settings.

  I have re-connected the printer to my wireless network, I checked that if I use a proxy server (I'm not), I used the HP print and Scan Doctor - just, it won't just matter what I do.

  All I can think about is the fact that I have recently purchsed a new router, but says that its connected which is what really stem me.

  This printer makes me crazy - please help

  Hi @mastersword64,

  Welcome to the HP community!

  I hope you have a pleasant experience with us.

  I want to help you with the connection error, you get on your e-all-in-one of HP ENVY 4500 printer when you try to enable web services.

  Here are some steps, I suggest trying to get your web services up and running it again:

  Network Power Reset:

  We'll leave the router and unplug the power cable (NOTE: do not reset the router.), and then do the same with the printer and shut down the computer. After a minute, plug in the router, wait to fully turn on, then plug the printer back in and wait for the wireless light become solid. Once the router and the printer are on, go ahead and re - turn on the computer. This will refresh the network connection.

  Restore the default settings of the network and reconnect:

  1. on the front panel of the printer, press your up wireless icon

  2. Select settings.

  3. Select restore default network settings.

  4 turn on your printer.

  5. once it is initialized to save, press the wireless icon again.

  6. Select settings.

  7. Select Wireless Assistant , and then follow the prompts to enter the details of your wireless network.

  8. try to activate the web services again.

  Configure a manual DNS for your printer:

  1 obtain the IP address of your printer

  a. This can be done by pressing the icon on the printer wireless.

  2. Enter the printer's IP address in a browser on your computer.

  3. Select the tab network at the top of the page.

  4. on the left, select network.

  5. Select network address (IP)

  6. Select manual DNS server

  a. manual Preferred DNS should read 8.8.8.8

  b. alternate DNS server should read. 8.8.4.4

  7. Select apply. You can get a warning simply select OK.

  Please reply to let me know if these steps resolve your issue.

  Good luck!