After update BIOS USB Ports not recognized on Satellite L500

Similar Questions

• Satellite Pro A300 (PSAG9E) - after updating BIOS Windows will not start

  Restart went well after update BIOS and Windows XP logo appears loads for a few seconds then a beep and restart - last good known or start Windows normally same effect.
  Reboot back to start - this is a new laptop - using the BIOS of Toshiba s official download site.

  Quite annoyed to try to find a way to upgrade or downgrade the BIOS.
  Took battery and RAM to see if I can delete it?

  Any ideas anyone?

  I think you mean BIOS * update * and do not upgrade ;)
  An upgrade is not possible

  However, you can try to remove the battery and the AC adapter and wait an hour. After that, reconnect the battery and the AC adapter and try to start Windows.
  Moreover I would load the default settings in the BIOS before starting Windows.

  If it doesn't work, it seems that your ROM module needs to be reflashed. In this case an ASP can help you.

• USB ports not recognizing keyboard and the mouse after sleep

  I have a wireless Logitech and mouse keyboard. These connect to my PC (Vista32) wirelessly via a USB plug small heel I plug into a USB port. Logitech called "Unify" which, according to them, is standard to connect devices through a USB port. My mouse and keyboard work fine when I restart my computer, but when he goes to sleep and I me re - wake up there that they do not have. I force power off of my computer because I can't access my account.

  I have ensured that the selective suspend setting in settings usb in advance power settings is disabled. Support Logitech seem unable to help him.

  Hey Sinclair,

  You can refer to this link suggestions and answer us with the State of the question.

  A USB device may no longer work correctly when Windows Vista comes out of standby or hibernation

  http://support.Microsoft.com/kb/928631

  Also refer to this link: How to troubleshoot USB device problems that can occur after a PC that is running Windows 7 or Windows Vista from sleep or hibernation resume

  http://support.Microsoft.com/kb/953367

  Registry WARNING: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, see this link:

  http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry

  I hope this helps.

• Satellite C650 - USB ports not recognized in Device Manager

  When I turned off my cell phone, I lose the use of my two USB ports. The only way I can get back them is to use Device Manager

  Go into the Manager of peripheral devices, Bus USB controllers, there are 6 x Intel ICH9 Family USB Universal Host controller 2 x Intel ICH9 Family USB2 Enhanced Host Controllers and 7 x USB hub root. When I lose the USB ports, USB root hubs seem to disappear, and the only way I can get back them is to uninstall the controllers and then right-click Universal Serial Bus Conrollers for "scan for changes on the hardware. This brings back the root hubs and USB ports work fine... until the computer turns off again.

  Someone at - he encountered this problem and managed to resolve it? Its a hassle to have to go through the uninstall it / Reinstall procedure each time. Your advice will be appreciated.

  Hey Buddy,

  You use the version preinstalled Windows from Toshiba or did you install your own version? I don't see any information about the BONES in your ad...
  Theoretically, it could be a software problem so ports USB work correctly if they recognized in Device Manager

  You should also try to update the Web from Toshiba site chipset driver. Maybe it helps.
  Otherwise, I could imagine that the update of the BIOS can also operate and this update you can get on the Web from Toshiba site too.

• USB ports not recognizing devices

  USB ports for laptop Toshiba Sateliite do not recognize camera or other devices?

  Hello

  Check the configuration/settings (BIOS/CMOS) often F2 when you start - make sure that USB is enabled.

  For a laptop, using a real computer shop (no leeks and glances at a Best Buy or other large surfaces)
  Stores) or system manufacturer support.

  Check with Toshiba support, their drivers online (update or reinstall) and their forums.

  Toshiba - Forums
  http://laptopforums.Toshiba.com/

  Toshiba - Contacts
  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/navShell.jsp?CF=su_contact

  Toshiba - drivers - access your model
  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp?NAV=download

  Toshiba - Support
  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp

  ------------------

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------------------

  Then lets refresh the USB stack

  Control the click Control Panel - Device Manager - no matter where in the box of white/white - then the VIEW - see the
  Devices disabled - look around (with the exception of USB controllers) for your devices (can have
  zero or more than one) and top - right click UNINSTALL.

  Control Panel - right CLICK on EVERYTHING - Serial USB controllers - Device Manager and UNINSTALL
  all except the category itself - REBOOT - it refreshes the drive and battery USB

  This KB shows XP how to and the method of Vista is identical
  http://support.Microsoft.com/kb/310575

  This is a utility to help you, but do 1 above.

  USBDeview is a small utility that lists all USB devices currently connected to your computer, thus
  as all USB devices that you previously used. Run Options and check the 1st three choices to see to it there
  Is there.

  http://www.NirSoft.NET/utils/usb_devices_view.html

  You must remove all instances of the devices and restart.

  ----------------------------------------------

  If necessary try these two:

  Tips for solving problems of USB devices - and a Mr Fixit
  http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx#EGB

  Hardware devices not detected or not working - Mr. Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  I hope this helps and happy holidays!

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• USB ports not recognized anymore

  I have Vista.  USB ports and ports that accept cards camera no longer recognize them.  Scanner can be moved from USB port to the USB port and works but "Explorer" does not show that they exist.  How to recognize camera cards (mainly) as they did before?  Windows offers device (camera card) has a problem, but this isn't the case.  Card works so executed through camera (USB cable to the USB port) in two different cases with two different cameras.  Also plugged on the USP port scanner is not recognized by the function 'Explorer' but actually works very well.

  Hello ghpots,

  ·         What happens when connect cards camera on USB ports, it installs the device drivers?

  ·         What are the changes that you made to your computer, since it has stopped working.

  When you connect your devices to the USB ports, check the status of the device in the Device Manager. Check if you see a yellow fringe or exclamations in the Device Manager.

  I suggest that you remove and then reinstall all USB controllers.

  To remove and reinstall all USB controllers, follow these steps:

  1. click on start, type Device Manager and open the Device Manager.

  2 right-click every device under the Bus USB controllers node and then click on uninstall to remove them one at a time.

  3. restart the computer and reinstall the USB controllers.

  Plug in the removable USB storage device and test to make sure that the problem is solved.

  Check the Device Manager to see if the unit under section USB or other devices. To do this, follow the procedures below:

  Method 1:

  1. click on Start, right click computerand select Properties .

  2. click on Device Manager.

  3. click on the (+) sign next to Universal Serial Bus controllers and next to the peripheral plus other section.

  Look for the USB device under the Universal Serial Bus controllers, or under the other devices section.

  4. If the unit is under Bus USB controllers or other devices, click on the reference to the 'unknown' device name, and then click Uninstall to remove the device.

  5. close Device Manager, and then restart the computer.

  6. If the USB device that has problems with software and it has not already been installed, install the software, now follow the planned manufacturer of the directives.

  7 reconnect the USB device that had issues and test to see if it works.

  The unit should now work correctly. Continue if the device name is not found in the Device Manager.

  Method 2: There may be a problem with the USB port. Try connecting to a different USB port. If the USB device is displayed in Device Manager after plugging the cable in a different port, then uninstall and reinstall the software of USB device driver.

  Method 3: Check the manufacturer of the device for support if the device is still unable to display.

  Thank you
  Irfan H, Engineer Support Microsoft Answers. Visit our Microsoft answers feedback Forum and let us know what you think.

• Pavilion 17-g192dx: USB Ports not recognized

  Hello

  I have a HP Pavilion 17-g192dx that's installed with Windows 10 factory. I decided to give the new operating system a go, but was overall very satisfied with his overall performance and updates of buggy. Not wanting to give up the new machine, I decided to bring it back and oldie but a goodie - Windows 7. I got a copy of Windows 7 Home Premium lying around so I gave a go and installed the operating system. I got the internet running successfully and in no time most of my drivers have been installed. The problem that I face now is that the old BONES will not work with my USB ports. I do not use a hub and have almost exauhsted the drivers for this Web site section. If someone wants to kindly point out how I could go about fixing this issue, any help would be much appreciated.

  I'm not as interested to get back to Windows 10. It is too slow for daily use (ma) and buggy.

  Thanks in advance!

  Hello:

  Download, unzip and run the file setup.exe from the link below...

  https://Downloadcenter.Intel.com/download/22824/USB-3-0-driver-Intel-USB-3-0-Extensible-host-controller-driver-for-Intel-8-9-100-series-and-Intel-C220-C610-chipset-family?product=65855

• Satellite A80-135 PSA80: after updating Bios keyboard will not

  SATELLITE A80 - 135 MS (MS is for Spanish)?
  model PSA80E-04C00JSP
  SER 55XXXXXXK

  Windows xp sp3 Spanish

  -> Update of the riginal 1.5_ bios (bios ID EAT10 / EAT20 bios version: v1.50)
  for _v 2.8_

  Downloaded bios - 20070709170816.zip of the Spain of toshiba
  http://es.computers.Toshiba-Europe.com/innovation/download_drivers_bios.jsp?service=es

  Unzipped the file and found an excutable "windows installation" and "AT10280a.rom".
  Double-click on the installer and...

  .... Now the keyboard is used for nothing (strange signs instead of letters)

  During the update (windows xp) I think I saw something on a master (original rom backup) in c:/windows/temp
  but now I can't find the backup rom.

  Can anyone help?
  Would it be possible to 'downgrade' to the bios (1.5) original and if so... where can I find it?

  Thank you

  Hello

  I don t know why it happened after updating the BIOS, but I guess that the language of the keyboard settings are not correct.

  Go to Control Panel-> Regional Options & language-> language (second tab)-> Details

  Here, you must choose the right keyboard (Spanish) language?

  Good bye

• Qosmio F50 - after update BIOS Bluetooth does not work anymore

  I need to update BIOS and F50 v 2.20.

  After update Bluetooth stopped working. Bluetooth in the taskbar icon turned red and I couldn't use any bluetooth device. I got my comp. 3 times to factory State, nothing has changed. After that I uninstalled the bluetooth stack, when I re install the installation crashes and now there is no icon in the taskbar and no link in Control Panel.
  I've tried everything.

  Need some professional help. My computer is only 2 months old.
  I am very angry.

  There is a new version of battery available Bluetooth.
  http://APS2.toshiba-tro.de/Bluetooth/?page=download

  But before install you it I recommend to remove the old battery installation BT.
  After removing the battery of BT, reboot the laptop and follow the BT facility.

  Installation should finish correctly and then you can activate using the FN + F8 keys.

  Should work.

• USB ports not recognized on the computer.

  erased win 8 and reinstalled win 7 ultimate. Now computer will not recognize and usb ports. What should I do?

  I use a Compaq Presario 5320. USB works, that I plug my Saitek yoke and it works correctly. It's only usb drives I plug in I get the message, that he doesn´t recognize...

  TA

  The problem with coming back to win 7 is may or may not win 7 drivers.  I would contact Compaq to see if there is win 7 drivers.

  Another problem if your computer comes with win 8 pre-installed revenant may void the warranty

• DVD is not recognized on Satellite L500-1XJ

  Hi all

  The DVD is not recognized when a dvd was released in the laptop.
  I tried to reinstall the driver but no luck.
  Does anyone have an idea?

  Thank you

  Gunter

  It is not easy to say what the problem is here.
  We don t even know what DVDs you are using.

  Maybe you should write a little more of everything cela and offer some fact and relevant information. You know, for a better understanding.

  Also which driver you have installed again?

• Re: Satellite P100 - after update BIOS it does not start optical drive

  I have updated the BIOS to 4.70 in my P100 PSPAAE. After restarting, I expect about 10 minutes, but nothing has happened, after that the screen of the BIOS, the screen went black. I turned off the laptop only.

  I chose the option "start windows normally". Since (I assume) the laptop does not drive. Any, I have to start from there. Everything else works fine.

  It is because of the update of the BIOS, or something else could cause this problem? Any idea or help appreciated!

  Hello

  The optical drive is recognized from the BIOS?
  You can read the disc in Windows?

  Maybe you should load the default settings in the BIOS and try another bootable disk.

• USB ports not recognizing any device

  I plugged into multiple items - iPod, iphone, USB keys.  Nothing is recognized.

  Hi kslicho

   

  1. What is the exact error message you get when you try to access devices?
  2. for how long have you been faced with this problem?
  3. have you made any recent changes on the computer?

  Method 1:

  You can even check if you get the error messages for the devices in the Device Manager. Please refer to the below steps.
  a. open the Device Manager by clicking the Start button, click on the Control Panel, clicking system and Maintenance, and then clicking Device Manager. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  b b.. in Device Manager, look for the device and then right click on the name of the device and go to properties.
  c. now on the general tab, check the status of the device. Let us know the status of the device. Also you can inform an error code with the State.

  Method 2:

  You can even check if uninstalling and reinstalling USB drivers to connect the hard drive. You can disconnect all USB devices and then perform the following steps:

  a. click Startand then click Control Panel.

  b. click system and Maintenance, click Systemand then click on Device Manager.

  Note If Control Panel is in Classic view, double-click System, and then click Device Manager.
  If you are prompted for an administrator password or a confirmation, type the password, or click allow.

  (c) in the Device Manager, double click on extend "Controllers of Bus USB", right click on the host
  Controller, click "Uninstall" and then click on 'OK '.

  d. Repeat step 2 to uninstall all items under 'USB Bus controllers'.

  Then, restart your computer and Windows 7 will automatically reinstall all USB controllers.

   

  I hope this helps.

• USB printer not recognized after Windows update

  OT: usb device not recognized

  After that suddenly stop, reboot, done, the device is plugged in where the printer indicates that it does not recognize the device. I said abattissent unplug it and reconnect it and if it doesn't work me to replace... I re install the driver for the Hpdeskjet940c but nothing works...

  Hello grasshopper.

  This problem may be caused mainly by broken printer drivers, this could have been caused when you installed the updates. I suggest that you start with a restoration of the system on the computer by choosing a restore point when it was working fine.

  a. Click Start, type system restore in the search box and then in the list click on the system restore program.

  b. If you are prompted for an administrator password or a confirmation, type your password or click on continue.

  (c) in the System Restore dialog box, click on choose a different restore point and then click Next.

  d. in the list of restore points, click a restore point created before you started having the problem, and then click Next.

  e. click Finish.

  You can see the following article for reference:

  http://Windows.Microsoft.com/en-us/Windows7/products/features/system-restore

  You can also try driver restore on the computer and check if it helps.

  To roll back a driver in Windows send the driver to the version that was finally installed for the device. Restoring a driver is an easy way to return a driver for a working version when a driver update fails to fix a problem or maybe even a new problem.

  a. open the Device Manager. To do this, click Start, type device in the area Manager search and then click on Device Manager in the list programs.

  b. right click on the device for which the previous version of the driver is desired and then click Properties.

  c. click the tab drivers.

  d. click on Roll Back Driver.

  Thank you
  Irfan H, Engineer Support Microsoft Answers. Visit ourMicrosoft answers feedback Forum and let us know what you think.

• Dell Vostro 5470 not get Dell Logo after update bios in Windows 10

  Dell Vostro 5470 not get Dell Logo after update bios in Windows 10.

  Laptop computer has restarted:

  1 Fireed power led,

  2 Powered hard drive for 2 seconds to turn it off.

  3. stops...

  No Dell Logo, no beeps, can't go in the Bios.

  Test LCD works OK.

  Remove the module of Ram, power on and listen to beep

  Pressing the END key and power for laptop has no effect.

  Any idea?

  Yes. I did it.

  Laptop have bios Phoenix.

  Phoenix Bios have restored the USB Flash procedure.

  This procedure to restore the BIOS:

  1. download USB flash less than 4 GB.

  2 format in FAT.

  3. get your flash update of the Dell store - xxxx.exe

  4. run cmd.exe and in the command prompt, run /writehdrfile xxxx.exe

  5 extracted copy of Bios.cap for the flash player.

  6. turn off the power to the laptop.

  Next 7,8 step may not be necessary but I did it.

  7 disconnected all perihpericals with battery and charger.

  8 disconnect the HARD drive

  9. connect the USB on the laptop on the right side.

  10 press and hold the END

  11, Pluged the power cable and the relase the END key 1 second after the power cord is in.

  12 USB led on stick flashed quickly and we see the process of recovery of the Bios on the screen.

  13. After finishing laptop restarts and worked well.