AIO 810 cannot parse after re - install

Similar Questions

• OfficeJet 8500: Cannot parse after upgrade Windows 10

  After the upgrade to 64-bit Windows 10 Pro, I can't scan my OfficeJet 8500 909n.  I get this message:

  "The analysis cannot because another program or computer using the networked HP imaging device. Try again later. »

  I have a / re installed HP Solution Center 5 times.  I restarted routers.  I'm power cycling my PC and the printer several times.

  I can print to this printer from three PC.  I can't get the scan to work as before.  This has been driving me crazy for more than 5 hours.  I'm honestly ready to go back to Windows 7.  The printer is connected via the cable network.

  Can someone please help?

  Thank you.

  Kind regards

  Jim

  Hello

  Thanks for the comments, you can try this alternative software:

  HP extended Scan
  
  FTP://FTP.HP.com/pub/scanners/HPScanExt/HPScanExt.msi
  
  Once it has downloaded and installed, go to start > all programs > HP > HP Scan extended > Run "HP Scan extended.
  
  Let us know if it works.

• Cannot parse after loading Office 2007

  It seems that the installation of the new version of OFfice 2007, my scanning capabilities have since disappeared.  I think that would be the problem.  I have a HO Officejet 7210 all in one.  I usually use Corel Draw or Corel Paint to scan the acquired scanner still appears as the HP twain but when I try to scan I get the windows Setup window and it calls for an installation disc.  I have DL all the current drivers.  but it can not find the scan.msi file.   Any help is appreciated.  Windows XP Pro

  The problem of not being able to scan after that loading Office 2007 has been addressed through an online chat with an HP technician.  It took 40 minutes.  For the record I have an XP, a Vista and Mac work all through my HP All in One 7210-no has ever had a problem with any impression.  It turns out that the scan.msi file disappeared after Office 2007 installed on the HP > after too long to try as many bugs that didn't work, the tech finally proposed I put in the original installation disc find the scan.msi file and copy it to the folder C/programs/HP and/or the program in C/Hewlett Packard.  That fixed it!  All right.  I do not understand then that when I told him I kept getting the error message was to locate the missing .msi file, it didn't suggest the obvious solution first.  They are paid by the minute?  In any case, it works now, FYI - any any graphics program, CoreDraw, Corel Photopaint, Photoshop Design and Word, I think has a "select him scanner-usually a Twain and then a command image acquisition."  You do not have to go through HP Director, although some of these programs scan to the Director.  The function of chat line, although long was a good immediate response to a problem.

• Cannot parse after changing routers (MF229)

  Everything worked well and then over the weekend, I changed my router. The printer's IP address has changed.

  I can always print, didn't reset anything to print.

  But I can't scan. The Toolbox MF said "a supported scanner is not installed." The Scan MF network utility does not display a scanner.

  I read in an old post that a similar (2013) problem has been resolved by reinstalling the drivers. Is this really necessary?

  Thank you!

  I finished to download and install the new drivers. I also had to install the Patch of digitization of the network. Now everything works.

• HP Officejet Pro 8620: Cannot parse after upgrade to Windows 10

  After switching to Windows 10, I found that I could not scan to my computer using a USB connection.  I ran HP print and Scan doctor and he said that everything was OK and I could actually scan a document into my computer using the "scan test" function of the program.  However, the normal scan would not work with the error msg 'connection to computer is lost.  So I uninstalled the current HP printer driver software and downloaded the recommended replacement.  The scan does not always for the same reason.  Still printing HP and Scan doctor said that everything is perfect with the scanner but now when I try to do a 'test' scan I get the message "HP Officejet Pro 8620 is not found".

  This same package worked for many other clients, so I don't feel the driver/software it is, on the contrary, I suspect that the question has something to do with the computer.  I'm always happy to do everything that I can to help if you want.

  I suggest running the tool (SFC.exe) System File Checker. If you do not know how, you can use the following link for instructions: System File Checker: run sfc/scannow & analyze its logs in Windows 10 / 8 / 7.

  Another thing we can do to help isolate the problem is to perform a WebScan.

  I made some screenshots for you that might help, I know that sometimes it is easier when you have a Visual. You will need to get the printers IP address from the front panel of the printer. You can touch the wireless network icon and view in the menu wireless settings. Take the IP address and enter the address of a browser bar.

  In the embedded Web server, click settings

  

  On the left side, click the administrator settings

  

  You will see the following message will appear, click OK

  

  You can now select continue on this site

  

  It may take a few minutes for the next page load. You might even see get a message that says: "Internal system error", if this happens please just refresh the page. (you can tap F5 on the keyboard to refresh)

  

  Once the WebScan is enabled you can click the WebScan tab above and do a scan. Please let me know if it works or not.

• Cannot parse after installation of new Mac OS 10.6.3

  I had no problem with my old OS 10.5 to scan.  The first scan after update 10.6.3 I received the diagnosis, 'Scanner could not be initialized. Scanner not found. "Printer worked fine.  I then reinstalled the CD software HP and now I get diagnosis "failed to open a session on this unit. No scanner found. "Printer still works.  What should I do next?

  I can now scan with OS 10.6.3 after downloading the drivers for the HP customer service > all-in-one printer, HP OfficeJet J4680 > Software and Driver Downloads.  The Apple software update did not work, but this driver is HP.

• Cannot parse after upgrading to Snow Leopard - C4580

  I have the HP all in one single C4580. No problems of printing or scanning up to that I've upgraded to Snow Leopard. I can still print but I can't scan unless I have used Image Capture. The printer does not appear in the window HP all in one device selector. I did set up the wizard again but my home network says that the server has failed and will not recognize the scanner. Anyone with the same problem?

  [title edited for clarity]

  You still have the HP software for 10.5 installed.  It does not play well with 10.6.  Let's remove this way:

  Go to Applications/Hewlett Packard / click Uninstall HP
  Click on continue
  Highlight your device in the left pane
  Hold down the Ctrl and Opt Cmd and click on uninstall
  There will be a pop up that asks if you are sure you want to uninstall all hp software. (At this point, if you continue, all HP printers you have installed will need to be reinstalled)
  Click on continue and let it finish

  Now run a software update.

  Then, remove and reinstall the printer in System Preferences, Print & Fax.

  You do not have the software now since Snow Leopard as well print & scan drivers built-in. scan from Preview apps or Image Capture. Scan from the front panel of the printer does not work yet.

• Hi, after you install Minecraft in my iMac, I get this message: "cannot start minecraft, if you run from a dmg, please drag applications and try again. I Don t know how to start the game. Thank you

  Hi, after you install Minecraft in my iMac, I get this message: "cannot start minecraft, if you run from a dmg, please drag applications and try again. I Don t know how to start the game. Thank you

  So what measures through 'install '?

• L830 satellite - Bluetooth cannot connect after installing Win 7

  I reinstall (Windows 7 Home Premium) on my laptop PSK84V-02400UAR Toshiba Satellite L830, and install all the drivers, but after you install all the drivers, I can't connect any Bluetooth device to this tour...

  When I search using the Bluetooth window it shows in the search window and after a while ' * could not detect the remote device * ' *... Kindly help... awaitng your valuable response.

  Can you please post exactly details how you installed the software and drivers Bluetooth?
  I think that you have made some mistakes there

  Your laptop supports the Atheros WLan card. Right?
  I think that this Atheros WLan card compatible with BT as well. This means that you need to install a special driver that allows to share WLan and BT in a single module.

  This driver calls filter for Atheros Bluetooth driver package.
  Therefore, install the driver Atheros Wlan, Atheros Bluetooth driver filter and battery Toshiba BT package.

  Then BT must be installed correctly and you should be able to activate it in order to start the pairing process.

• Aspire E3 - 112 cannot start after win10 own attempt installed

  The installation is wrong. He went right through the extract process and install OK but then just went along in a loop to keep reinstalling the usb drive. I changed the bios by promoting usb hdd over windows Boot Manager (in uefi). So I removed the USB drive and restored the order of the bios. But now, when I boot, I get an error window saying "the computer restarted unexpectedly or encountered an unexpected error." Windows Setup cannot continue. To install windows click OK to restart the computer, and then restart the installation. "It makes no difference if I close the window or click OK, it goes through the same circle.

  Help!

  Thanks for the reply. I tried that. In the end, I found that the solution was to wait for the beginning of the (umpteenth) reinstall the process and then press the power button for a few seconds until the machine stops. Then I powered up while pressing the F2 and is gone in the bios where I restored the original and the machine parameters and then started in the new clean install.

  Unless the OS is nuked, how to perform a clean install is using the settings > update & security > Recovery > restart now and use the boot from usb option. And leave the bios alone.

• Dell AIO 810 printer will still work with Windows 8?

  Hello, I know that Dell said that do not have a driver for Dell AIO 810 printer? The question is if there is no work around to make it work or do I have to wait for a driver, or just buy a new?

  concerning

  Rizvolo,

  If you have installed Windows 8 and it is a Dell computer, have you installed the drivers in the correct order, Dell System Software (if applicable) and the first chipset drivers? How to download and install drivers in the correct order If it is not first a Dell computer, chipset drivers?

  If I'm not mistaken, it is an older printer and was made before Vista. Usually using the Vista drivers, if applicable can work. I also use the drivers XP 64-bit on some models.

  Download the drivers XP 64 - bit for the Dell 810 printer and follow the steps and install them on the drivers in XP SP3 compatibility mode.

  Run print jobs remove, restart your computer, disconnect the printer, run the patch (cleaning of printer utility), restart your computer. Make sure that the printer has been removed, install the drivers for XP 64 bit in XP SP3 compatibility mode. You should get invited to connect to the printer.

  Have you you get prompt enough to allow the printer after your anti-virus program? Enable the printer after Microsoft Essentials/Windows Defender

  Rick

• I plug in a device after I installed the drivers from the USB says windows can't recognized the device what should I do to solve it.

  I plug in a device after I installed the drivers from the USB says windows can't recognized the device what should I do to solve it.

  Hello

  I suggest to go to the link below and run the fix tool provided or follow the manual procedure provided to solve the problem.

  A computer that is running Windows XP cannot detect a USB, an Apple iPod flash drive or an external hard disk drive

  http://support.Microsoft.com/kb/925196

  You can also check the below link for more information about advanced troubleshooting tips for General USB in Windows XP problems.

  http://support.Microsoft.com/kb/310575

• Acer aspire has stopped working after I installed vista service pack, a

  After installing Vista service pack 1, I was unable to restart my computer. Nothing has worked. I went through the Startup Repair, but it ran all night and nothing. I have no disk, so I tried to do a system restore, but still nothing. I know very little computers if you can give me some details step by step on the following questions would be most appreciated.
  

  (1) how do I back up my data

  (2) how to restore my system

  Thank you

  Craig
  

   

  If the system or Mode restore safe work not and you do not have a Microsoft Vista DVD, make a repair disc to do a Startup Repair:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use:

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner:http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Data recovery:

  1. slave of your hard drive in another computer and read/save your data out there.

  2. put your Hard drive in a USB hard drive case, plug it into another computer and read/save from there.

  3 Alternatively, use Knoppix Live CD to recover data:

  http://www.Knopper.NET/Knoppix/index-en.html

  Download/save the file Knoppix Live CD ISO above.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://isorecorder.alexfeinman.com/isorecorder.htm

  Download the Vista software from the link above.

  After installing above ISO burning software, right click on the Knoppix ISO file > copy the Image to a CD.

  Knoppix is not installed on your PC; use only the resources of your PC, RAM, graphics etc.

  Change the boot order in YOUR computer/laptop to the CD/DVD Drive 1^st in the boot order.

  Plug a Flash Drive/Memory Stick, BOOT with the Live CD, and you should be able to read the hard drive.

  When the desktop loads, you will see at least two drive hard icons on the desktop (one for your hard drive) and one for the USB key.

  Click on the icons of hard drive to open and to understand which drive is which.

  Click the icon for the USB drive and click on "Actions > Change the read/write mode" so you can write to disk (it is read-only by default for security reasons). +

  Now to find the files you want to back up, just drag and drop them on the USB. When you're done, shut down the system and remove the USB key.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Vista recovery media obtain and/or use the Partition Recovery Vista on your computer to the factory settings .

  There is no Vista free download legal available.

  Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

  Normally, they do this for a cost of $ small.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

  See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

  Normally, you have to press F10 or F11, Acer is normally Alt + F10 at startup to start the recovery process...

  Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Also ask them if it is possible to do the recovery disk/s since the Partition of recovery in case of hard drive failure or System Crash, when you are replaying the ad.

  .

  They will tell you how to do this.

  Every computer manufacturer has their own way of making recovery disk/s.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Or borrow a good Microsoft Vista DVD (not Dell, HP, Acer, recovery disk/s etc).
  A good Vista DVD contains all versions of Vista.
  The product key determines which version of Vista is installed.

  There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

  If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  http://support.Microsoft.com/default.aspx/KB/918884

  MS advice on the conduct of clean install.

  http://www.theeldergeekvista.com/vista_clean_installation.htm

  A tutorial on the use of a clean install

  http://www.winsupersite.com/showcase/winvista_install_03.asp

  Super Guide Windows Vista Installation

  After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.

  See you soon.

  Mick Murphy - Microsoft partner

• AFTER YOU INSTALL SERVICE PACK 1 FOR WINDOWS VISTA, MY COMPUTER WILL NOT START SAYS UNATTENDED, DLL

  AFTER YOU INSTALL SERVICE PACK 1 FOR WINDOWS VISTA, MY COMPUTER WILL NOT START SAYS UNATTENDED, DLL

  Follow these steps to try to solve your problems of boot.

   

  Restore point:

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

  Do Safe Mode system restore, if it is impossible to do in Normal Mode.

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  http://www.windowsvistauserguide.com/system_restore.htm

  Read the above for a very good graph shows how backward more than 5 days in the System Restore Points by checking the correct box.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

   

  If the system or Mode restore safe work not and you do not have a Microsoft Vista DVD, make a repair disc to do a Startup Repair:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use:

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner:http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  See you soon.

  Mick Murphy - Microsoft partner

• Error "Windows Setup cannot continue. To install windows, click ok to restart the computer, and then restart the installation. "When you try to install Windows.

  How can I configure my windows 7 after restoring my laptop to the factory conditians?

  My laptop had a blue screen and I couldn't get rid of it, I went into safe mode and restore my computer to factory conditions. When the computer says "the installation program starts services" you stop and I couldn't turn it back on for 15 minutes. When I turned on and tried to contained my setup, a message keeps poping up "the computer restarted unexpectedly or encountered an unexpected error." Windows Setup cannot continue. To install windows, click ok to restart the computer, and then restart the installation. "But no mader, how many times I reboot my laptop, the same message appears. What should I do? I've restored my computer several times and never had this problem.

  You should try another recovery.

  New computers coming often pre-installed with Windows 7 have what is called a recovery partition. This is used to reinstall an operating system in the case of a system failure. To access it, you need to start when you start your computer by pressing a function key. This can be either F1, F2, F9, F10, F11, F12 key DEL or tab. See the manual that came with your PC for instructions on how to reinstall Windows.

  If your recovery partition is not available or damaged, you must contact the manufacturer of your computer, and request that a defined recovery disk you can use to reinstall Windows 7. They could practice a small shipping and handling.