AIR-AP-1231 for guest access

Similar Questions

• Steps required for guest access / self-supply accounts

  I'm a little overwhelmed with the information concerning the establishment of users invited on the wireless network and have a few questions I was hoping that the community would respond.

  I use a WISN on the 4.2 version of the software, as well as a WC on the same version.

  1. is it possible to have accounts created by users themselves, once they join the wireless network? If so, what will do to put in place?

  2. a VLAN especially should be created for customers to use?

  For the first question, if you want more that putting an email address for tracking needs, users Fella5 is right.

  To answer the second question, it is unnecessary on the plan technique one VLAN special for guest users. In most cases, however, you should have one to better apply the security settings of your network clients. In our office, with 10 people, we use the same subnet for guests, voice and internal data. However, we use 3 different SSIDS with different policies and security strategies QoS applied to them. And the guest SSID has an ACL applied to limit traffic to the Internet only. When you are given a 27 subnet to use, do you :)

• Approved sponsor guest access

  I was now all day and fight a little bit. Someone at - it a doc very detailed on-site sponsor guest access approved with ISE 2.x and WLC code version 8.2.110.0.

  I went through the process of implementation of the portals to the best of my abilities. I have my users who authenticate with ISE with PEAP for Wireless Corp. so I know it works.

  How can I tell WLC/ISE which SSID I use for guest access? Also my customer get IP address, then it should be redirected?

  I get this error on the WLC:

  * apfReceiveTask: 20:37:31.136 Jun 13: % CSA-3-CLIENT_NO_ACCESS: apf_80211.c:4285 Authentication failed for the customer: c0:cc:f8:17: of: 25. ACL substitute incompatibility of AAA server.

  And I see this in splunk:

  June 13-15:50:28 10.20.0.60 June 13-15:50:28 ise01 CISE_Passed_Authentications 0000157854 4 0 15:50:28.428 2016-06-13-05:00 0006695154 5200 NOTICE Passed-authentication: authentication successful, ConfigVersionId = 90, IP = 10.20.63.14, DestinationIPAddress = 10.20.0.60, DestinationPort = 1812, UserName=C0-CC-F8-17-DE-25, Protocol = RADIUS, RequestLatency = 12, NetworkDeviceName = BNA-WLC2500-01, username is c0ccf817de25, NAS-IP-Address = 10.20.63.14, NAS-Port = 1 Type of Service = call check, Framed-MTU = 1300, Called-Station-ID=d8-b1-90-08-87-b0:TEST_GUEST, Calling-Station-ID=c0-cc-f8-17-de-25 Identify NAS = _GUEST, Acct-Session-Id = 575f1c94/c0: cc:f8:17: of: 25 / 23, NAS-Port-Type = Wireless-IEEE 802.11, Tunnel-Type =(tag=0) VLAN, Tunnel-Medium-Type =(tag=0) 802, Tunnel-Private-Group-ID =(tag=0) 142, cisco-av-pair is audit-session-id is 0a143f0e0000000f575f1c94, Airespace-Wlan-Id = 3, OriginalUserName = c0ccf817de25, NetworkDeviceProfileName = Cisco, NetworkDeviceProfileId = 8ade1f15-aef1-4a9a-8158-d02e835179db, IsThirdPartyDeviceFlow = false,

  I can't reach the SSID from my iphone... but it looks like his tent. I suppose an ACL is wrong or a policy is wrong. I think that I have trouble with the VLANs that are pushed to clients.

  Any help would be great thanks...

  Could you send a screenshot of the configuration of the radius server in the WLC (detail page please).

  Did you take a glance at the wlc/monitor clients if the ACL has been pushed for authenticated clients? What is the result?

  Thank you

• How can I put an icon on your laptop MAC Book Air - i.e. Facebook (for faster access)?

  How can I put an icon on your laptop MAC Book Air - i.e. Facebook (for faster access)?

  Drag it to your desktop.

• ISE 1.4 and access for guests with distinct SMS providers

  Could someone please help with the installation of the guest access. I am trying to perform an establishing a unique SSID prompted with two central WISN and a pair of ISE 1.4 to manage a building containing different companies.  Installation work good with a sponsor (company) chooses just the customer who registered but at the end of the implementation the handover raised a question that left me speechless.  Every company wants to have their own account SMS provider. How can I configure so that the end-user location defines the SMS provider?

  Hello

  There are 2 different stand-alone ise or there are members of the same deployment?

  You can add gateways sms on the parameters of the ise. So if there are 2 different deployment, simply choose the sms gateway that you created in a configuration Portal comments.

  If you have only 2 servers ise 1 deployment, you can create 2 comments portal on each one you set the right sms gateway.

  If you have 1 deployment and have the same ssid comments:

  -divide PSA between 2 companies using the AP group

  -to the ise, you can use the defined strategy (simpler and more readable).

  -According to the AP group, you can Portal popup comments 1 to 1 group AP and another portal of comments for another group of AP. In order to make this work, you need to change the type of id station call on the Security tab, on the wlc himself.

  hope this is clear.

  If you have deployed MSE, you can set your rules and popup portal based on the physical location without the use of the AP group

• Guest access / traffic meter

  I had the AC1900 for a few months and I also use access as a guest.

  I was wondering if it was possible to limit the volume of traffic on the access of the guests?

  No, it is not possible to place any cap bandwidth on guest access.

• Cannot use guest access

  On a new XAC1900 after the installation of a home network based on IP fixed, with the main computer wired and all other 8 devices connected WiFi and no problem at all, I tried to use guest access.

  I have configured the SSID with the suffix - comments and assigned a password. The SSID of the network is visible on the context of the WiFi but the connection will never be finalized.

  The device of the guest, I checked that the SSID of new comments, within its DHCP system, have not been assigned the 192.168.33.XX expected but one IP address, from 169 etc, which corresponds to a provider (not Italian), other then mine. Of course I can not access or enter any password.

  I contacted the support chat system that was very available, but unable to give a solution.

  I checked the configuration several times and reinstalled the latest firmware, but no result even manually.

  Failure is repetitive and the strange IP DHCP assigned to the Guest device is always the same (even after the days), showing that the data seem to be in the firmware. Also after firmware reinstall (verses 1.1.42.162280).

  I have no more ideas!

  Dear all, first thanks for your help. I finally found the solution. Here's how, for the benefit of third parties.

  When I configured the primary network, as always I posted, several equipment (PC, iOS dev, Iphones, portable computers ipads, etc.), fixed IPs. They were assigned in the numbering according to the IP Address of the default router 192.168.1.1. That's why from 192.168.1.2 to 192.168.1.255. I does not take any care about toggle point control DHCP on the router connectivity, and it remained empty. During today muttering I thought: Let me see if activating only not the DHCP protocol to the main network could stop the DHCP server to the SSID of comments. And that's all!  I had to explicitly enable DHCP in connectivity for the second (one guest) to exploit SSID.

  Once again thank you all

• E3200 guest access and phones

  Hi all

  Hoping someone here can help me with this problem.

  I have access as guest enabled on my router (firmware v1.0.4). E3200  Computers / laptops can connect, enter the password and use it very well.

  When I try to get a smartphone connect (tried 2 iPhones, 3 Windows phones and 2 different Android phones), they are able to connect to the network, but even after the opening, a browser, will never get to the "hotel" Cisco, landing page, allowing them to enter the guest access password and connect to.  By checking the connection on the phone settings, I see that they have acquired an IP address from 192.x.x.x correctly

  Specifically, I bought this router so that I would not give my WPA key when people came and wanted to use their phones on my network.

  Has anyone successfully got it works?

  Thanks in advance...

  Ok...  After a lot of messing around and reset the default settings, I finally got to work and can repro the problem at will.

  If the you are in a two router setup and the E3200 isn't the main router (i.e. in bridge mode), guest access will not work for smartphones.  Once I swapped the roles of my two routers (i.e. made the main router E3200), guests for Smartphone access works as expected.

  Don't know if a moderator / owner of the firmware feature reads the forums, but if you do, I consider this a bug.

• App of Smart Wi - Fi and Guest Access + Bridge Mode

  Hello!
  I put my WRT1900AC as in Bridge Mode Access Point.
  Everything is OK. But I identify some things not usable, when my router is in Bridge Mode. Such a thing is the creation of a guest for Wifi/guest access account. The Linksys App Smart WiFi offering however, but it does not work. When I put the guest access 'ON' it just stay naturally 'OFF '.
  My question: is it supposed to be the case, or it may become in the future renewed with the software?
  At the same time, I can change a lot of things with this Smart WiFi App, when my WRT1900AC is in Bridge Mode. Proven stuff: Wifi channel number change and change the filter MAC they work correctly.

  With all the Smart Wifi router when the clipping comments wireless value is disabled, because the guest network depends on DHCP for IP subnet isolation.

  Is there a way to keep all the features of the WRT1900AC and the route of a primary network. It is an advanced configuration, because you must configure a static route in your main router and configure the WRT1900AC as a router not gateway.

  Discussion of the example:

  https://community.Linksys.com/T5/access-points/configuring-multiple-routers-in-one-network/m-p/93246...

• Mode bridge E4200v2 + guest access: No DHCP IP assigned?

  New E4200v2 2.0.37.  In "Bridge Mode - DHCP" (i.e., Access Point router).  Guest access is enabled & SSID broadcast.  DHCP server is disabled, because my main Sonicwall router that provides related to major network 192.168.1.0.

  PROBLEM = PC Client can see "-comments ' fine SSID and associate with her, BUT PC does NOT receive an address IP DHCP (i.e. 192.168.33.x) so the browser login page never appears and guest access does not work.

  I'm sure it's related to DHCP.  I'm assuming that the E4200 not receives or sends the comments with the PC client DHCP packets.

  I saw guest access works on the old E4200v1 before so I know what it should look like.

  Can anyone suggest any probable cause why my E4200v2 would not be providing comments DHCP addresses in the 192.168.33.0 subnet?

  I don't have that 24 hours until I have to deploy 2 new E4200v2 at a remote site and after that it will be really hard problems because I will not be on this site.

  Thanks in advance for expert advice!

  I think I SOLVED!

  Apparently, you need to ACTIVATE the two SERVER NAT & DHCP on the E4200, * before * you switch to BRIDGE MODE.

  When I did this, access as guest - works great!  Hooray!

  I guess the E4200 needs to use these 2 services that run in the background to give the subnet access as guest & dhcp work assignments, which is a process hidden, once you're in Bridge Mode.

  Wow, Cisco should really have a section of the guide user or KB article about it.  Or at least when you click on Bridge-Mode a little pop-up asking you to ensure that these 2 pre - req for are enabled.

  I'm moving now.

• 4 x WAP4410N VLAN for guest network

  Hi there everyone,

  You want to have a problem of my resolved.  I am running 4 x WAP4410N access points configured with one corporate ssid with WPA2 Enterprise authentication that points to a server in network access protection.  What I'm trying to do is to add a second ssid to all my points of access for guests only and cannot connect to the departmental resources/devices.  I think I have to VLAN so that it works correctly.

  Four access points in various parts of the building are connected and are wired in different switches SG300.  A port on a SG300-52 in my server room is plugged into a port on my firewall that I would use for DHCP.

  What should I do to get this working correctly?  At the time of my comments to test network is not even give an IP address to the devices, which I think is related to the VLAN.

  I do not know what ports I leave the identified tag-no, how to configure the VLANs on multiple switches, etc.  Any help would be appreciated.  It was suggested to me that I could use dedicated to guest access separate access points, but I like to keep the amount of access points down to the minimum required.

  I think you may have found the problem. I apologize I have not asked if you were on layer 2. I would have thought it.

  If they all Layer 3, maybe you could just add a few routes? Switching is not my field stronger.

  Personally as needed I just don't sleep 2 and use VLANs

  Eric

• Cisco ISE 1.4 - guest access

  Hello world

  We use the ISE 1.4, now, we want to use the guest access ISE Module. I created the user invited on portal of the sponsor. Now, how can I configure authentication and authorization policy? I want to verify the user.

  Thank you.

  Hello! I strongly suggest you check out the videos of laboratory Minutes on access for guests and all the rest too :)

  http://www.labminutes.com/video/sec/ISE

  Give those a try and let us know if you still need help.

  Thank you for evaluating useful messages!

• Sufficiently secure guest access?

  Equipment: controller 2106, 1131AG, WCS 5.1.151

  Internal users: connect to the network of 192.168.x.x as wired users. Authentication with a radius connected to the AD server. Use WPA2. Vlan1

  Users invited: to connect to the controller through web-auth, DHCP on controller, Vlan2

  Comments (in sequence) ACL rules:

  1 allow SourceIP 0.0.0.0 / 0.0.0.0 IP Destination 192.168.1.5/255.255.255.255 (firewall)

  2 refuse SourceIP 0.0.0.0 / 0.0.0.0 Destination IP 192.168.0.0/255.255.0.0

  3. allow SourceIP 0.0.0.0 / 0.0.0.0 Destination IP 0.0.0.0 / 0.0.0.0

  I understand that the suggested method for Wlan guest must be in the DMZ on a separate controller. As each location has its own firewall/internet connection I find this expensive solution, a nightmare administrative and probably exaggerated. My question is: is my pretty safe guest access with web-auth, VLANs separate and list access control?

  The reason why using as establishing s ACLs on the wlc is because it's not really work as well according to your rules. ACL is better managed on the L3 interface.

• How to download to iCloud for iOS for offline access device

  How can I download a file from iCloud drive iPhone 6 for offline access?

  The file would need an app to run in.  For example, a Word file could run in the application of the word iOS.  What kind of file is it?

• Extend my extreme network with another extreme - waiting for internet access

  Hello - I have a new generation Airport Extreme (let's call it Extreme1) connected to a Comcast modem and it works very well. The extreme will be the router that the modem has no router function. I'm trying to expand my network to another room with another extreme (let's call it Extreme2). I have a connection cable between two rooms. Extreme1 has an ethernet cable from one of its LAN ports connected on port WAN Extreme2. When I try to create a new network with Extreme2 (in aid of the same name, passwords, etc.) it does not work. He was suspended at the end when he is looking for a connection ("Waiting for internet access")-I did the following things based on what I read here:

  1. Changed IPv6 link local parameters
  2. Tried the whole upward on my Macbook and tried on my iphone
  3. The Wan first and then tried to change the configuration after you done for Extreme2 by creating a network
  4. Tried to create a network with Extreme2 connected directly to the modem
  5. Extreme2 factory reset after every attepmt

  And nothing works. Kicker is, I also have a reasonably new airport express and the same thing happens to her as well.

  Do I need to adjust some parameters of network that I'm not aware of? Is it possible that my LAN ports are disabled on Extreme2? It is brand new.

  Thanks for any help.

  Have you used the Apple Setup Assistant?  If you did, it had notified you that the extreme second was being configured "add using Ethernet. The wizard will automatically configure the second airport with the appropriate settings for you.  All you have to do is enter a name of device for the second AirPort Extreme.

  Here I'm assuming that you reset the second extreme to parameters by default until you set it up again and that your second Extreme is the current version of the "tower" or that of previous versions "flat or square.

  The example below shows an AirPort Express as the device which is the extension of the network, but you will see the name of your network and AirPort Extreme on your configuration screen.

  Post back if you need some tips on using the "Wizard" for your configuration.