management of WCS, WLC and H-REAP AP1242

Similar Questions

• 4402 WLC and WCS

  Hi all

  We have 3 WLC 4402 all with identical config and we use Lobby Admin to create guest accounts.

  Problem with this is that the guest account must be created on 3 WLC.

  I installation WCS and want to know how to extract the 3 existing wlc and their config in the WCS.

  Can the admin of lobbay can create accounts on the WCS and grow them into all wlc

  Hi RR,.

  >I install WCS and want to know how to extract the 3 existing wlc and their config in the WCS.

  It's pretty easy. You must add a new controller via the configuration-> page controllers. The option 'Add the new controller' is in the drop-down list at the top right of the screen. You can use a list separated by commas of IP addresses to add all three at the same time. WCS audit of the controller software and get to the bottom of the config.

  >Also can the admin Hall can create accounts on the WCS and grow them into all wlc

  I have not used the account Admin Hall (it is not really appropriate in the office where I work), but I know that you can create a guest account in the controller model launch pad. It is under Security in the sidebar. This model can then be applied to all three WLCs at the same time, that will simplify things. I guess you would need to make sure that your Hall administrator can access this particular part of the WCS.

  Hope that helps.

  -Jason

• questions about 2100 wlc and lwap connection

  Hello

  I have a few questions, I hope you can answer me.

  In fact, I have a controller connected to 3 Lwap 2100, and they are connected to the WCS. they have a static IP address.

  The distance between each point of access to more than 30 meters.

  1. the distance between the access points affect the accuracy or the stream. How can I calculate this

  2. because the APs use a static IP address, each customer should I connect to the network to add a static ip address? can I do the APs detect clients dynamically?

  I have lwapp reset guide, guide WCS configuration and configuration guide for WLC. If you have more documents or more pls share with me.

  BR

  Yamani

  Hello Ahmed,.

  Yes the distance between AP affect the wireless signal.

  to determine the best location of AP and the distance between them, as the site survey is necessary with the expert of the spectrum wireless or airmagnat...

  You can check the following links for design and RF management

  1) http://tools.cisco.com/squish/1Ea09

  2) http://tools.cisco.com/squish/51a58

  for other questions about DHCP, it is not a must that customer use static IP, you can always configure them with DHCP.

  as an extenal DHCP (like windows server), or on the WLC himself (to the title of controller-> > internal DHCP tab).

  Kind regards

  Talal

  =========
  Please note the answers that you find useful and mark as answer - when is it :-) - so that others can easily find

• Version of vs WCS WLC

  Hi guys,.

  can I use the version 5.2.178 on my controller and 4.2.110 on my wcs?

  Best:

  WLC and WCS to run the same major version (4.2 and 4.2,5.2 and 5.2) or are the wlc and wcs not linked version?

  (5.2 and 4.2)

  THX...

  You need to upgrade your WCS in 5.2.130 for you allows to administering WLC running 5.2.178 or 4.2.176 on your controller with your existing version of WCS.

• Manage a WCS by SNMP

  Hello

  I will need to supervise a SNMP remotely through WCS (version 4.2).

  Can what mib I use to get information such as CPU used on the WCS, space free hard disk, number of AP, number of rogue AP, number of LWAPP tunnels, number of users of wifi connected at all points?

  Kind regards

  You'll have to ask the WLC and not of WCS.  The application of WCS is unresponsive to SNMP requests.

• When he puts an end to Firefox 3.6.6 firefox.exe continues to turn, visible in the Manager of tasks (XP) and stimulates the activity of the CPU up to 60% with the danger of overheating. Have not found an appropriate response with the search term "abnormal

  When he puts an end to Firefox 3.6.6 firefox.exe continues to turn, visible in the Manager of tasks (XP) and stimulates the activity of the CPU up to 60% with the danger of overheating. Have not found an appropriate response with the search term "abnormal termination of the program."

  This has happened

  A few times a week

  is after update of Firefox 3.6.4

  I have the same problem with Firefox 3.6.6 except that it also consumes massive amounts of CPU during the race. This version also adds a new process on your system. I am running XP and in the beginning I tried to disable some plug-ins. Always consumed too much memory. I went back to version 3.6 and the new process went, and the CPU consumption is way down. Something is wrong with the latest version of Firefox, I never saw behave this way. Revert to a previous version (Filehippo) and you will see the difference.

• NB100 - "Update Manager" will automatically load and start to run

  Whenever I turn on my NB100 (Ubuntu ReMix) the "Update Manager" application load automatically and begins to run.

  How can I stop this happening?

  Thank you
  David Lowe

  I don't know the English names. In the German version, it's the "Einstellungen" menu and there, use the "meetings".
  (Blue icon with a large arrow left)

• Management of user accounts and Parental control in Windows 8

  Hello

  I'll post a thread on how to manage the user accounts and Parental control in Windows 8.

  A user account allows you to connect to Windows 8. By default, your computer already has a user account that you have been
  needed to create when you configure Windows 8. If you want to share your computer, you can create a separate for each Member of your household or office user account. You can also choose to associate any user account with a Microsoft account. Signature with a Microsoft account will bring all your SkyDrive files, contacts and more in the start screen. You can even connect to another computer that has Windows 8 and all your important files will be there.

  Here is a video on how to manage the user accounts and Parental control in Windows 8.

  Also, here is a document showing you how to manager Our user on Windows 8.

  If you have any questions let me know.

  THX

  I hope it's useful.

  THX

• Manager of the PCF and HotKey UI does not

  I use Windows XP.  Recently, when I stopped windows it will not close automatically.  I get a message that the FCP Manager does not respond and I have to close it manually.  Then I get a message that the HotKey UI is unresponsive and I don't have that close it manually.  Windows then quits.  All this began after I uninstalled BitDefender Security Suite.  What's past and how to fix it.  I tried safe mode and restore the system through normal means.  None worked.

  Hello

  ·        What is the exact error that you are experiencing?

  I suggest you follow the steps mentioned in the article below.

  Advanced Troubleshooting for shutdown problems in Windows XP

  http://support.Microsoft.com/kb/308029

  Apart from the pursuit of Bit Defender security, you can also try Microsoft Security Essentials, which offers protection in real time for your home PC that protects against viruses, spyware and other software malware protection.

  For more information about Microsoft Security databases, I suggest you to check the below link.

  http://www.Microsoft.com/security_essentials/

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Desktop Window Manager has stopped working and was closed

  One of our machines (HP Pavilion dv7 Notebook PC running Windows Vista x 64) will receive the error "Desktop Window Manager has stopped working and was closed" with lots of close error. He reappears (as well as all windows flasher to non-aero, then back to aero) in a few minutes, spends about 5 times per hour.

  I did some research on this and have already taken the following measures without a bit of luck:

  1 run the command chkdsk / SFC scan - nothing found via chkdsk, SFC found some issues fixed, and some, it did not set. Them that it solves not all related to Windows Sidebar, which I do not / does not start.

  2. put updated drivers for ATI Radeon 3200HD - this had a lot of new questions. Installing caused newer drivers ATI catalyst to no longer work with errors during installation and popup errors at startup. After trying several solutions workaround to try to get installed it, I ended up coming back to the driver that came with the laptop, that are properly installed and working without error. I am skeptical of update of this stable driver as a solution to the dwm.exe error.

  3. this problem just started yesterday, that occur with not a lot of changes. Other than updates of windows (I think that .NET framework and a few other updates installed), I replaced NOD32 antivirus with Bitdefender antivirus. The system was stable with bitdefender for about 2 weeks, so I'm not convinced that this program is causing the error.

  4. the event viewer shows the following:

  Failing application Dwm.exe, version 6.0.6002.18005, time stamp 0x49e02696, failed module ntdll.dll, version 6.0.6002.18881, time stamp 0x51da3d16, exception code 0 x 80000003, offset 0x00000000000461f0, process id 0 x 124 error, start the application time 0x01cea0365a457adc.

  Offset, process id and start on time all vary, but there are a lot of these application errors in the viewer all screaming Dwm.exe like the failing application.

  What should be my next course of action?

  You do not receive an error but a caveat. NTStatus results (the set of codes execption used by ntdll - the failed module) begin to 0 for no error, 4 for information (you should never see this), 8 for putting guard and C for error.

  It's your specific error.

  //
  MessageId: STATUS_BREAKPOINT
  //
  MessageText:
  //
  EXCEPTION {}
  Breakpoint
  A breakpoint has been reached.
  //
  #define STATUS_BREAKPOINT ((NTSTATUS) 0x80000003L) / / winnt

  Problem is, you shouldn't have breakpoints. Breakpoints are set by debuggers and stop the execution of the program to the State of the program can be examined. There should be no breakpoints in a retail system. More breakpoints are inserted into memory during execution of the program in a debugger. They tend not to do in the actual file.

  So here are two assumptions, either you have no exit code, IE test code (driver?). Or you have a running program that behaves like a debugger (which is suspect).

  Each of the three towers of programs, services, and drivers in increasing amounts. So restrict the possible culprits.

  Clean boot

  Click Start - all programs - Accessories - run and type

   

  msconfig
  

   

  Then go to the Startup tab uncheck everything. Then go to the Services tab check hide all Microsoft Services and uncheck everything that is left.

   

  Reset. If this resolves your wake problem ½ of services / of startup items until you find that one.

  
  Tip clean boot

  If the above does not help.

  Download Autoruns http://technet.microsoft.com/en-us/sysinternals/bb963902.aspx

  Start the program by right-clicking and choosing run as administrator and click on the menu Options - Filter Options and check hide Microsoft entries and disable include the empty slots. Uncheck the box just to the left.

  Reset. If this resolves your wake problem half of the items until you find the one that.

  Safe mode

  If the above does not help.

  Click Start - all programs - Accessories - run and type
   

  msconfig
  

   
  Go to the Startup tab, and then click Start. Reset. Come back here and uncheck the box secure start to return to normal mode.

• My task manager has been disabled and need again.

  My task manager has been disabled and need again.

  Hello skyman13,

  You are on a domain?

  Take a look at the information published by MVP Ronnie Vernon here:

  http://social.technet.Microsoft.com/forums/en-us/itprovistasecurity/thread/41d5f720-177b-4786-a37f-1f7798c246ed/

  Lisa
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• continue to spread the message ' desktop window manager has stopped working and was closed ".

  continue to spread the message ' desktop window manager has stopped working and was closed ".

  The office then blinks and I can't use the Aero feature.

  Any correction or known issues?

  Thank you
  in2stocks

  Hello
  It is usually a video driver issue. Would like to know what controller you have and see if the manufacturer has a new driver for Vista.
  Please let us know if that was the issue.

  Mark <> Microsoft Partner

• unloading of feature to make dhcp off the WLC and put it on Active Directory.

  I need to use the feature of unloading to dhcp off the WLC and put it on Active Directory.  Someone at - it a walkthrough or a page for this?  I know it's just a checkbox and a redirect to the new dhcp server, but where the hell is the configuration on the WLC?

  Thank you!

  -anne

  You can go there.

  http://www.Cisco.com/c/en/us/TD/docs/wireless/controller/7-4/configuration/guides/consolidated/b_cg74_CONSOLIDATED/b_cg74_CONSOLIDATED_chapter_01001001.html

  Point to your existing ad integrated DHCP server.

• Cisco WLC and Apple TV Hello

  Hello

  I followed the guide on http://www.cisco.com/en/US/docs/wireless/technology/bonjour/7.5/Bonjour_Gateway_Phase-2_WLC_software_release_7.5.html on activation of Cisco WLC 7.5 with Apple TV good morning however I have a weird problem. I have some clients unable to see the apple TV connected to a different wireless access point while some may see the Apple connected TVs. I have attached my setup for reference. I would like to inquire about the use of LSS and so perhaps someone has encountered similar problems? The apple TV is discovered by the wlc on mdns-domain names.

  According to the document, multicast has been activated not however the discovery of the apple tv is intermittent of apple customers. Customer can discover apple tv 1 and 3 but not apple tv 2 and sometimes it can discover all 3 apple TV while client B is able to perceive all apple TV devices 3. All 3 apple TV devices are discovered by WLC and only apple TV service has been activated on WLC.  I was wondering if anyone has seen a similar question? Not too sure what can be the cause of it?

  Any suggestion is appreciated.

  Some of the docs didn't do it, but it is required as all my installation requiring Hello, set multicast implementation.

  Thank you

  Scott

  Help others using the system of rating and marking answers questions like "answered."

• How to manage stored user names and passwords on a computer under W7?

  I would like to remove a few names user ID in Yahoo.  Where can I manage these in W7?

  Hi KKBrown,

  Thanks for posting your question in the Microsoft Community Forum.

  It appears from the information you want to remove some names to user ID in Yahoo.

  It would be useful that you can answer these questions to help you best.

  1. you are trying to remove information from Yahoo mail?

  2. you access yahoo mail using the client program webmail or email?

  2. what web browser do you use?

  If you try to delete the user name or password stored on Web sites that you have visited previously by using internet explorer, you can see the article and check if that helps:

  DeleteAutoComplete information

  If you try to manage the usernames stored and passwords on Windows 7, you can use Credential Manager to store identification information such as usernames and passwords that you use to open log on to websites or other computers on a network.

  For more information, see the article:

  Store passwords, certificates, and other credentials for automatic logon

  Hope the helps of information.

  Let us know if you need help with Windows related issues. We will be happy to help you.