AirPrint for HP officejet 4500

Similar Questions

• OfficeJet 4500 G510n: a driver for HP Officejet 4500 g510n

  Need to source/install a driver for the Officejet 4500 g510n I plug opportunity after my 510 G packed. With the help of HP printer and scanner doctor finally told me "404 page not found" which starte just me all around alone again to tell Traoré (again), the page is not found. The 510n has a wireless option but is connected to my laptop through USB, and is identified by the doctor Scan from the HP (software) that need to be installed.  Any suggestions? Thank you. Martin

  Hello

  Please download the following driver & software and install on your computer:

  http://ftp.HP.com/pub/softlib/software12/COL32439/MP-80348-2/OJ4500vG510n-z_Full_13_en.exe

  (Note: to connect USB, please do not connect USB cable before the application process).

  Kind regards.

• failure to scan, copy and fax for HP Officejet 4500

  I'm trying to scan with my HP Officejet 4500 and it is not allowing me to do. When I turn on the printer it says "failed to scan. "Cannot scan, copy or fax. When I try to scan, I have the wireless option to send it to my computer and when I choose my computer, nothing happens and it takes back me to the scan, copy, fax menu.

  I tried installation and resettlement and unistalling too many times. I also unplugged all the wires. Nothing works. I had problems with this mutiple printer and it is not even a month. How can I solve this problem.

  I'm afraid that the error you are getting means that the firmware is glitched, or the scanner lamp is out. If the firmware is glitched, the printer might actually be fixable, but if the scanner lamp is out, there is no much you can do. The document below will take you through a few steps to try. If this does not work, try to do a partial reset. If nothing works, you need to replace your printer. If you are still in warranty, HP can replace the printer without cost to you. I'll link the information to get in touch with them below. The link takes you to a form to fill out. Once you fill it and she is treated, it will give you the printers warranty information, a file number and the phone number to call.

  HP Technical Support call case form:
  http://goo.GL/w7Hgh

  A "Failure of the Scanner" Message appears on the all-in-one control panel and you can not scan, copy, or fax:
  http://goo.GL/KULAv

  To make a partial reset:
  1. make sure that the printer is turned on.
  2. pull on the power cord from the printer.
  3. pull out the power cord from the wall.
  4. wait for 30 seconds.
  5 connect the power supply cord inot the wall, but do not connect the printer.
  6. press 3 and # buttons.
  7. while now buttons, plug in the printer.
  8. when the lights come on, release the buttons.

• Adding drivers for HP Officejet 4500 Desktop G510a-f in Windows 8

  I have a desktop HP Officejet 4500 G510a-f. My computer is a gateway HDM! Windows 8 operating system. My system has a virus really bad, so I had to just remove & return to manufacturing to installation so I'm having to put all the hardware, software, and pilots back on. The only one that Im having trouble with is my all in one PRINTER! I have the HP solution for the resettlement of the printerdrivers Center. Usually when I complete, I get a message; "The system cannot find the specified file" then it gives a path: "

  C:\Users\Diana\AppData\LocalTemp\7zS7A17\Setup\hpzshl.ice_s... (Im unable to do the rest if there is no cause its in high bar section.)

  I also received another message simular:

  C:\Users\Diana\AppData\Local\7zS4B42\Setup\hpzshlautor

  Can someone help me as soon as POSSIBLE!

  Diana

  Hi Diana,
  Follow the steps below and check if it solves the problem:

  1 open the Mcafee Virus and Spyware Protection software you are interested in, click on calendar and perform analyses. Click analysis in real time, and then click stop. Select until I restart the PC and confirm by clicking the button turn off.

  Now, try to reinstall the HP software and check if the installation goes as planned.

  If the problem persists, continue following the steps below:

  2. open the dialog box run by clicking on the Windows key and the R key on your keyboard. Type %windir%, and then click OK.
  3. type hpoins*.dat in the search bar at top, if there is that no result rename the extention in old instead of dat. (e.g. hpoins1.old)
  4. type hpwins*.dat in the search bar at top, if there is that no result rename the extention in old instead of dat. (e.g. hpwins1.old)
  5. start the Run dialog box by clicking the Windows key and the R key on your keyboard. Type MSIEXEC /Unregister. in the Run dialog box and click OK.
  6. launch the Run dialog box by clicking the Windows key and the R key on your keyboard. Type MSIEXEC/REGSERVER in the Run dialog box and click OK.
  7. run the installation file and check all difference.

  Kind regards
  Shlomi

• Cannot install drivers for HP Officejet 4500 G510n-z (stuck control systems)

  -Officejet 4500 G510n-z

  -Windows 7 Home Premium

  -No specific error message

  -A occurred since the first attempt

  So here's the order of things:

  (1) attempt to hook the printer via USB to install printer drivers. Windows says it's failed to find drivers.

  (2) download the drivers (basic and complete) online.

  (3) try to install the driver. The installation process gets stuck checking of the system, which is the first step after the extraction of the file indefinitely.

  4) try again with the pilot basis with similar results.

  (5) turn off the firewall to avoid problems, try once more. He tells me that it can not extract, so I go in the temporary folder in which the files were extracted and delete them.

  (6) reboot, try again. Yet once, gets stuck checking the system.

  I'd love to rub it using the CD, but the problem is that the CD has been lost for a long time. If there is no other way to fix it, how can I get another CD?
  

  Hello Rstevoa,

  Steps below should set you wireless printing.

  1. Click Start > Printers and devices , and then
  2. Click Add a printer . then,
  3. Click on an Add a local printer > Next , then
  4. Click on create a new port: , select the"Port TCP/IP Standard, then THEN .
  5. type the ip address of printers under the host name or IP address 192.168.1.101 and click NEXT
  6. of the "list of manufacturers :, select HP and select"Printers"list"HP Deskjet 6980 series "and click on"
  7. NEXT
  8. Complete the wizard.
  9. Disconnect the USB cable between the printer and the computer

  Then try to print.

  Let me know if it prints.

  Kind regards
  Jabzi

  Help the community by marking this post.
  Your question has been answered? Mark it as a accepted Solution!
  See a great post? Give it a Bravo!
  I work for HP

• Apple Airprint for HP Officejet 6500 has more via a wired connection to the router

  Hello

  So I did a considerable amount of research in this through the internet and this forum and I still struggle to find a satisfactory solution.

  I have a HP Officejet 6500 a more connected by ethernet to my BT Homehub 3.

  It is I understand that even if there is a wired connection, as long as my iOS device (iPad 2 or iPhone 5) is connected to the same router, I should still be able to see this Officejet thanks to ease of airprint.

  Unfortunately, this is not the case. I get the message "No Airprint Printers Found" on both devices. The only way I managed to get my Mac Pro (Mavericks) to connect has been add to mannualy by using the IP address of the printer.

  Can anyone provide guidance on what I might hurt? Certainly, the printer must connect internet I can print from my iOS devices using HP ePrint app for iOS.

  Some might say, well, what's the problem, just use the HP application, but is not the point. I think that if something has been set up to make things easier, then use it. I chose this printer specifically for this feature is a bit frustrating for her so difficult to get the desired results.

  Hope it is something simple and anyone can help you.

  Thank you

  Steve

  Following this request and reading the many more similar questions, I think I may have solved this.

  I'm not 100% sure but I read a few threads suggests that there are issues around BT Homehub 3 and Hello so this can be a problem.

  I tried the following in the past two days...

  (1) completely don't reset my router (wiped all settings and started)-no luck!

  (2) I tried changing to WPA2 to just WPA security - no luck!

  (3) tried to convey the Hello to the printer ports - no luck!

  (4) turn off the router, printer and all the devices iOS then fed back router, printer, then iOS devices - printer appears on iOS devices, but when printing was selected iOS device returned on several occasions not connected printer error.

  Finally, what seems to have made (at least for now) has been...

  (1) disconnected the Officejet ethernet and set up as wireless.

  (2) off voltage router, printer and all iOS devices then propelled upward in the order listed previously.

  (3) so far, I tried to print a mail and a web page of my iOS devices, and both have been successful.

  By the way I've been struggling also to airplay from my iPhone / iPad until I started messing around with the settings above, and now this question also seems to be resolved.

  Due to the variety of combinations (different printers, routers, etc.) people will have, it seems to be quite difficult to find a solution that solves a single problem but I hope some of my experiences and findings could help others in some way.

• HP Officejet 4500 g510n: the driver for HP Officejet 4500 g510n link does not

  
  

  Hi @Sluglit,

  I see by your post that the download is coming up with a 404 error. I will definitely do my best to help you.

  I was able to put in place the URL you provided, using Firefox. But I noticed that it was for Windows 7.

  Here is the link for Windows 8.1. HP Officejet Full Feature software and driver.

  If you have problems opening the web page, try a different web browser.

  If you appreciate my efforts, please click on the "Thumbs up" button below. Thank you.

• Impossible to run the installer for HP officejet 4500 G510 install on Windows 7 Home Premium SP1 Toshiba Satellite. Any ideas how to fix?

  Setup running on the HP disc will not work.  No error message, stops just until it loads the installation program.

  I downloaded the site Installer Internet HP (versions complete and base).  Same results - cannot run the installation program.

  I contacted Toshiba, which says it's a problem of Windows 7, and communicate with Microsoft.

  I installed this printer at least 10 times on some other operating systems without problem.

  I want a wireless printer that prints, scans, and faxes, but impossible to get the installer to run.

  Any ideas on how to solve this problem?

  Hi PCCoachFL,

  Printer HP office jet 4500 G510 is compatible with Windows 7. For more information please visit the link below:

  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/search.aspx?l=en-us&type=hardware&s=HP%20officejet%204500%20G510%20&OS=64-bit

  I advise you to install download drivers for the printer HP office jet 4500 G510 and check if it works.

  http://h20000.www2.HP.com/bizsupport/TechSupport/DriverDownload.jsp?prodNameId=3919446&lang=en&cc=us&TaskID=135&prodTypeId=18972&prodSeriesId=3919445

  You can also see the article for more information:

  Printer in Windows problems

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  Hope this information helps.

• Set default color in black and white for HP Officejet 4500 driver

  Is it possible to set the default color setting black and white driver and not in color?

  I know how to change the setting for each document that I want to print, but I print almost all black and you want to set the driver up to always default to black so I did not change the setting in the properties of each time.

  Thank you

  Hi Ltaff,

  I can't wait to hear that you have questions.  This can be set in the preferences.  Please see the steps below.  If you would like more information about your product, click here.

  1. go to the device folder and printer

  2. right click on the device

  3. Select printing preferences

  4. on the quality tab, select the Advanced button

  5. in the aspect tab, find levels of grey or black only printing

  6. click on the text to fill the drop down

  7. Select printing in grayscale or black ink only

  8. click on ok

  9. on the Preferences dialog box, select apply (this keeps the setting)

  10. then click ok

  11. attempt print job

  I hope this helps!

• Windows 10 for Officejet 4500 driver

  Hello

  I've updated from windows 8.1 windows 10 and after my windows activation, even once, I did a clean install of my windows.

  After a successful installation and activation of windows, tried to install the printer driver using the driver windows 8.1.

  Installation began, but after the detection of the printer, it hangs at 'check' HP scan interface 2 to 92% and stays there... I tried your solution given in your website and forums as the restart and everything, but nothing works. I have my printer connected via an Ethernet cable with my router.

  We need drivers for windows 10 for HP officejet 4500 G510 series printers. Impossible to find on the pilot and Web site download page.

  I don't understand, how a Prime Minister like HP business fail to update their drivers with a new version of windows? It's just not cool.

  Thank you and best regards,

  Dr. serge pacome

  HP released drivers Windows 10 Compatible for HP Officejet 4500. Thank you so much HP.

  Here is the link-

  http://support.HP.com/us-en/drivers/selfservice/HP-OfficeJet-4500-all-in-one-printer-series-G510/3919445/model/3986392#Z7_3054ICK0K8UDA0AQC11TA930C7

• OfficeJet: pilot for OfficeJet 4500 / 10 Windows

  I had to reset my Gateway Laptop due to update Windows 10. It resulted in a complete loss of programs on the computer. (data seems to be ok) Loss of program included driver for HP OfficeJet 4500 G510g-m.

  try to download the results of the pilot in a product for Windows 8 or 8.1 Windows; then after a few minutes, a box of said msg: unable to load the software. Any help much appreciated.

  Hi @JimEblen

  Can you ensure that your Windows 10 updates are installed and up to date?

  As long as you have selected Win 10 on HP site, it must download to win 10, so ned not to worry if it says otherwise.

  Hope that helps!

• Power supply for Officejet 4500

  The power supply for my Officejet 4500 packed. Someone knows how to get a new or old get that fixed. I tried several shops local computer without success.

  Here are the details of the part you are looking for:

  Power cord: 8121-0889
  Power supply: 0957-2269

  You can call HP (1800-474-6836) to place an order, or there are many editors who have these parts.

• OfficeJet 4500 K710: error in installing driver for officejet 4500 K10...

  Got to the installation of the driver for the officejet 4500 HP support K710... at first I thought it was a success, but later it says fatal error in installation... What can be the problem... the printer was given to me by a friend who emigrated abroad... even the CD that came with it was not working...

  Hello

  Download and run the HP printer installation wizard to install the printer

  www.HP.com/go/Tools

• Driver HP Officejet 4500 G510 for Windows 8

  HP has a new driver for the OfficeJet 4500 G510n wireless printer to use with the Windows 8 operating system upgrade?

  Here is the link for the driver and software, you will need. I hope this helps.

  http://goo.GL/ph9aT

• Suite software HP Officejet 4500 for Mountain Lion

  Hello

  The full suite of software for the Officejet 4500 HP will be released for Mac OS 10.8 (Mountain Lion OS)?  If Yes, what is the estimated output?

  In addition, initially, I was able to print but not scan.  The HP software uninstalling and installing this package from Apple was a work around that allowed me to do both.  You can highlight on the page of support of 4500's for Mac:

  http://support.Apple.com/kb/DL907

  Just for info.  Thank you and looking forward to the complete HP print/scan software update for Mountain Lion.

  Hi Justin811,

  Thank you for your message and share your experience. I happy that you can analyze now after I installed the driver for printer HP from the Apple Web site package.

  Currently we have no information when a full features software will be available for your device and the Cougar. However, we have the solution via Apple Software Update and HP Printer Driver Update that provides print drivers, faxind and digitization through Capture of Image.

  You can continue to watch the page HP Driver & Software for your Officejet for updates.