All desktop computers in the State of the report '(missing)' View Manager

Similar Questions

• Image change by default do not apply at the office pool View Manager 4

  When I try to change a pool of offices to change the default Image, everything seems fine. I chose the snapshot I want to use and apply without any error. However, when I restart the desktop computers in the pool, they are still on the old default Image. I can tell quite easily because that new images flash plugin but the previous does not work. Everything on view eating seems correct, it shows the correct Parent virtual machine and good Image. Is there anything else I need to do?

  Thanks for all the help!

  It is the persistence of one or a pool not persistent?

  If it is a persistent pool you must also do a recomposition (under the image) to update virtual machines, followed by a reboot, etc.

  If there is no persistent pool, just restart desktop does nothing. The new image will only be used on the new computer desk/clones. Need to remove the old desktop computers.

• Network management problem, computer laptop Windows 7 will not find other computers on any network, however all other computers on the network can access Windows 7 laptop.

  Basically, the issue I'm having is that my laptop does not connect to any other computer to access the actions or other files.  Other computers on the network can access my computer laptop shares and files without any problems.  Operating system is Windows 7 Home Premium x 64.

  What I tried:

  restarted
  uninstalling and reinstalling the files and printers, sharing maps and restart after completion
  all disabled firewall
  tried with IPv6 enabled and disabled without change, so it is currently enabled
  tried on a Wi - Fi and the differences are listed below in the section work (work is wireless)
  able to ping other comptuers
  access to other computers is permitted by other computers

  problem extends over several networks, IE I noticed it at home last night and the followed problem my laptop at work this morning.
  The problem is slightly different on the two sites.

  At home:
  I can see the other computers on the network, but I am unable to access it, even if I have permission, but other computers can access to my laptop.

  At work:
  Cannot even find other computers on the network but they can find and access my laptop.

  I have worked on this problem of non stop for several hours and did much more than what is said, but I am unable to remember everything.  I should have been taking notes: P

  Here are the results of the ipconfig/all command (I removed the physical addresses for security reasons):

  Windows IP configuration

  Name of the host...: Radiation-G72
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.

  Wireless Network Connection 2 wireless LAN adapter:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft Virtual WiFi Miniport adapt
  Physical address.... :  **
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Ethernet connection to the Local network card:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. : hsd1.ga.comcast.net.
  Description...: Realtek PCIe GBE Family Controller
  Physical address.... :  **
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :
  ... Description: Atheros AR928X Wireless Network adapt
  Physical address.... :  **
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::f4e3:cd1c:6952:eb4d % 11 (Preferred)
  IPv4 address: 192.168.2.7 (Preferred)
  ... Subnet mask: 255.255.255.0.
  Lease obtained...: Thursday, February 4, 2010 10:50:32
  End of the lease...: Friday, February 5, 2010 08:29:36
  ... Default gateway. : 192.168.2.1.
  DHCP server...: 192.168.2.1.
  DHCPv6 IOOKING...: 234890707
  DHCPv6 DUID customer...: 00-01-00-01-12-4C-6E-91-00-25-D3-3D-FC-9A
  DNS servers...: 192.168.2.1.
  NetBIOS over TCP/IP...: enabled

  Tunnel adapter isatap. {1797D168-6FC8-4DDF-8338-4E214119C26D}:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft ISATAP adapter
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Teredo Tunneling Pseudo-Interface:

  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  IPv6 address: 2001:0:4137:9e74:4ea:2920:b81a:cdc5 (Preferred)
  Address IPv6 local link...: fe80::4ea:2920:b81a:cdc5% 13 (Preferred)
  ... Default gateway. : ::
  NetBIOS over TCP/IP...: disabled

  Card adapt 6TO4 tunnel:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft 6to4 card
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Asked this question in the Windows 7 forum also because the problem was between windows 7 and Vista.

  Hello

  If it has started, you can try a system restore - an update "might" have caused the problem.

  1. try a system restore back to a point before that happened. And immediately thereafter enter
  Control Panel - Windows updates - top left settings and set it to download and informs you instead
  Automatic. Leave it until you are sure that everything is OK and then you can add them one at a time
  to troubleshoot BUT click right on and HIDE all the driver updates. Also stop at day of drivers like below
  and let this value - manually search for drivers when you think you need. (See how and why to)
  stop day of drivers below.)

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  To uninstall an update if you determine that there are problems - Panel - updated Windows - down left-
  Updates installed - uninstall

  I had completely forgotten the system restore!  While looking into the system restore, I found that when I moved into my new House and has cable Internet installed, the cable technology installed a program of comcast on my computer.  This caused me to not be able to connect with other computers.  After rolling back to install it before it works!   Thank you.

• tabs of the device shows no no tabs of desktop computers in the same network

  Hallo,
  I have two PCs on my home network that running Firefox desktop connected to the same sync account. My work PC and an Android phone are connected to the same sync account.
  When I open "synchronize tabs" is show me only the tabs from the firefox Home Office which was last synchronized.
  All Firefoxes have different sycn name.

  What's not?

  THX

  Stefan

  problem solved you must reset "services.sync.client.GUID" about: config
  details, see here: https://bugzilla.mozilla.org/show_bug.cgi?id=1234181

• Using the value of the column of the report in view state

  Hi all

  I have a little trouble as long as you report column. Here's the problem I have face.

  I have a classic report in apex5 (universal theme). Please find the page here https://apex.oracle.com/pls/apex/f?p=62495:5:

  I want to have a condition that SAL column should appear only if DEPTNO! = 10. For this, I put a conditional display for SAL column that "point value / expression 1 column! Expression 2 ="and #DEPTNO # expression1 and expression2 10. But this doesn't seem to work. Can someone help me understand the issue.

  Note: I want to view only the column of the report, not the page item in the condition.

  Thank you

  Stephanie.

  Kalesh Ravi-Oracle wrote:

  I want to have a condition that SAL column should appear only if DEPTNO! = 10. For this, I put a conditional display for SAL column that "point value / expression 1 column! Expression 2 ="and #DEPTNO # expression1 and expression2 10. But this doesn't seem to work. Can someone help me understand the issue.

  It is not possible to report baseline values in the State of the reference column. It would be unwise to do so: how APEX can determine if the column should be included or not until all rows are retrieved?

  Note: I want to view only the column of the report, not the page item in the condition.

  Why? In the example given, this is the correct (and more effective) approach. If the condition must be based on the expected query results, then use a Exists (SQL query returns at least one row) or NOT Exists (SQL query returns no line) condition.

• Location of the backup folder View Manager - greyed out

  VMWare View - 5.0.1

  Try to change the location of the backup folder (View/view/servers/Edit Connection Configuration servers.  When I click on the tab back up, the location of the folder is grayed.  It is currently backup fine in C:\ProgramData\VMWare\VDM\backups, so there is no problem of backup.  I can't just change the path to what it's backup.  Do I have to stop a service to change the path?

  You cannot change this location by the Administrator display. Here it is read-only.

  You can change the location directly through LDAP, but by changing the attribute EAP-LDAPBUFolder for each connection to the server. See http://kb.vmware.com/kb/1010285

  Mark

• (3) all my computers have the same problem with installing KB953297. Microsoft must provide an easier way to solve this problem. Obviously a lot of people is affected.

  End users should not have to be remove and reinstall anything. Get it together!

  Can you guys try the following steps:

  1 uninstall .net Framework 1.1 from Add/Remove programs
  2 run the .net Framework Cleanup Utility and remove all .net Framework 1.1 related Articles (located here: http://blogs.msdn.com/astebner/archive/2006/05/30/611355.aspx)
  3 Windows Update to download updates.
  4 reboot and redo the update of Windows

  Can you let me know if you find any success?

  Thank you! If you find my answer was what you're looking for, remember to click on the box "mark as answer" below!

• Permissions on the report templates & views

  Is it possible to give a non admin user permission to copy a view exsisting or models or give him the right to create a new view or report templates without the ability to remove or modify the default / built-in views and models report?

  The user must be able to remove the views & templates report he created or copied himself.

  I tried this but as soon as the user got delete it or change the law he was also able to remove or change models and integrated views.

  UPDATED July 18, 2016: I dropped a request for service at VMware for that matter.

  Het bericht is bewerkt door: Simmetje

  VMware support response:

  Hi Rob,

  I have troubleshooted this extensively in my 6.2.1 lab environment and concluded that it is not possible to achieve in vROps at the moment and we look at a feature request.
  I came to the same conclusion that you mentioned in the case where as soon as the user got delete or modify right he was also able to remove or change models and integrated views.
  Even a view or a report created and owned by the local user admin can be deleted by a user to test if they have the delete permission that their responsibilities under the management of the views. If you don't give them the delete permission, even when they create a notice or report that they own, they are not able to remove it.

  In contrast to the dashboards, which can be shared by the local user administrator and set up for a user in turn, views and reports are not the same.

  In order to put this file, we would suggest to send a feature request. Would you mind signing your request using the link below:

  http://www.VMware.com/company/contact/contactus.html?Department=prod_request

  It is the best way to get traction on requests for features or product improvements, you can have.
  The RSS link in the various heads of product and based on the feedback they receive, they have the opportunity to submit requests/improvements of features for future product versions.

• Address IPCONFIG auto cannot locate my Ip address. Other computers on the WIFI at home have problems of "IP address conflict address" How can I fix

  Auto IPCONFIG can find 169. addresses. My IP BigPond do not answer to 169. I force the IP to get internet now. I'm trying to return to power enable all desktop computers 3 and 5 laptops (all windows) to use WIFI that we used to be able to 2 months ago. BigPond advise me to get in touch with Microsoft on 132058 and I can only do this Mon - Fri 9.00 - 5.00 which is extremely difficult so that an employee who works 12 hours. After hours of contact would be much more preferable. How can I have my computer 'automatically' identify my IP without forcing the numbers. When I force the IP on the other computers on the home WIFI network they can not access the internet due to a "conflict with an IP address. They should automatically be able to identify and define the same IP address as the primary computer without problem. How can I fix?

  It seems much more likely that the fault is in your TG782T on Windows.

  Either way, a 'normal' router will work with many more than 4 Ethernet ports (though most only have a maximum of 4 physical Ethernet Sockets) and more than 5 wireless connections.  It is therefore likely that your ISP has "customized" your device in a way that limits the number of connections - and it is probably this "customization" that gives you your current problems.  It will be a little difficult to do this via an Internet forum (rather than sitting in front of your computer), but it should be possible.

  Please specify the following sentence: "disconnect this computer and try a new computer is always the same problem as the gateway must always have this setting, this computer in IP."  What is "this setting of intellectual property?

  In the area of local connections > Internet protocols (TCP/IP), how is the 'work' computer configured?  Normally, it would set on "Obtain an IP address automatically."  What was the setting of 'alternative' that your ISP you are trying?

  The first thing to do is to get information on your work computer.  Follow these steps:

  1. click on start, and then type the three letters cmd in the run box, and then click OK.
  2. Enter the following command and press ENTER:
  ipconfig/all > "% UserProfile%\Desktop\ip.txt" {Enter}
  3. open the IP.txt file to your desktop
  4. copy and paste the text into your response.

  One of the lines in IP.txt will be something like the following:

  ... Default gateway. : 192.168.1.254

  This number is the IP address of your router.  Open a web browser (Firefox or Internet Explorer) and enter the IP address of your default gateway in the address box.

  At this point, it is possible that it will ask you a user name and password.  If you did not one, use admin as username and leave the password empty box.  If this does not work, there is a way around this, but it involves several phone calls from your ISP.

  Unfortunately, the only manual for the TG782 I could find is terribly incomplete. http://www.thomsonbroadbandpartner.com/GetFile.php?id=6978

  After login, you should see a page with a menu on the left (see p. 26 of the pdf above thomsonbroadbandpartner).  Click on the entry for "Home Network."  Unfortunately, the manual does not show the screen that appears when you enter this part of the configuration utility.  What you are looking for are the settings for the DHCP server on the router, which assigns IP addresses to computers connected to the router (no matter if they are connected by wire or wireless).

  Because the manual for your TG782T is not describe it, take a look at this, which is a part of the Linksys WRT54G Router configuration utility:http://cid-18b259158254905b.office.live.com/self.aspx/.Public/router%20setup.jpg

  Under the Network Configuration, the local IP address is set to 192.168.1.1.  On your router, the default value for this entry is 192.168.1.254.  Just under which are entered for "DHCP Server" "" starting IP address"and"Maximum number of DHCP users."  Here are the settings that you want to search.  The two critical parameters, as regards your current problem is are (1) the server DHCP must be "enabled" and "(2) the number of DHCP users Maximum" must be equal to or greater than the total number of computers that you want to connect (wired and wireless).

  Sorry I can't give you more specific instructions.  Usually, the user guide for the router will display all the available screens in the router configuration utility... but not this one.

• PCoIP connections directly on the desktop or via the connection to the server?

  Hello

  I have install a single view connection server and office pool and I can connect to the pool very much using the customer view pointing to the login server.

  I recently added a second login server replica and if I try to connect via the customer view succesfully authenticates, allows me to choose a pool, but errors and then with "the connection to the remote computer has ended."

  Look at newspapers in firewall, can I see traffic blocked from my desktop PC (where the client to view runs) to the IP address of the VM on the port office 4172. Of course, I can open this port, but I do not understand why this should be necessary when using the first server likely traffic goes through the connection to the server, not directly to the customer. The behavior looks different during the passage through the replica, but I don't see why this would be the case?

  You can enable/disable tunneling with a broker for connections setting.  Maybe the second broker (replica) does not make any tunnel and trying instead to go directly through your PC.

• Several desktop computers

  Hello

  I use several computers desktop (accessible by the Mission control). I just added a third and my apps are bad! I have a set for Outlook upward and a few other applications, office (Word, etc) applications and my third new office for Adobe CC applications. Everything was fine until I started using the third office. I put the options to keep the apps I would like it - office 1, 2, 3, all desktop computers, this office etc... my problem is that apps in 2 and 3 keep switching places, even if I put exactly where I want that they!

  Sounds trivial I know not, but why OS X gives the option to position them if she's going to ignore it? Y at - it a bug? She is currently set?

  Any help appreciated.

  Thank you.

  Open 'System Preferences' and go to 'Mission Control'. Uncheck the box 'AutoArrange spaces based on a more recent use.

• Units media center is always available on current HP desktop computers?

  I don't see this option for all desktop computers. This feature disappeared new offers?

  Hello

  For computers that are provided with Windows 8/8.1, media library is not available - it can be installed as an additional feature on running machines (or upgrade to) Windows 8/8.1 Professional - see Microsoft article at the following link.

  http://Windows.Microsoft.com/en-GB/Windows-8/feature-packs

  Kind regards

  DP - K

• Unable to connect to desktop computers CentOS 7.2 after yum update

  We are in the process of piloting to a few dozen CentOS 7.2 offices for our internal teams and have encountered a problem with updates (the first day, no less!)

  I built this model about two weeks ago. We have shrunk to the low enough to start on cloning. There is a Pool of dedicated, manual offices. On these machines, users have a high degree of freedom.

  Seems that when install us updates on these desktop computers, however, the VM will show as available in the view, but the connections via HTML or reviews can be made of these machines.

  That's what we continue to see in the newspapers on these machines:

  2016 02-26 T 13: 14:34.383Z < pool-1-wire-4 > [BlastHandler] overflow ERROR the Blast Server time-out to listen on port: 33166 SESSION of TopicMessageManager-pu00infwks020: 4ac8_ * _0e4e

  2016 02-26 T 13: 14:34.384Z ERROR < pool-1-wire-4 > [StandaloneAgent] could not start blastHandler: exceeded the timeout of Blast Server to listen on port: 33166 SESSION of TopicMessageManager-pu00infwks020: 4ac8_ * _0e4e

  While it is waiting for support to help us, is there anywhere else I can be looking?

  -mike

  Yes, thank you for including the bit about the virtual bridge that gets implemented for newer CentOS and Fedora - we have removed that in the model we have created for them.

  In collaboration with VMware and rummage through the newspapers, it was a total self-inflicted problem.

  We have a script that runs when the first connection - it will set the first person who connects with sudo rights on the desktop. During this process and since the script button the file/etc/passwd, the user vmwareblast has filed.

  Without user vmwareblast there are no running service vmwareblast.

  We have added this user and adjusted this script and we're all good.

  -mike

• Made up of desktop computers to view stuck on a manual after restart

  I'm having a problem with the commissioning clones using VMware view 5 and Win 7 SP1.  During the procurement process, the clones run fine and it seems that everything is going well until what happens at customization stage.  The scope of VMs a point where nothing happens, the State in the pool Office Administrator window says "Customizing".  If I let desktop computers in this State, nothing happens, and when I check every clone in the vSphere console, I don't see that desktop computers are stuck at the prompt say "reboot is necessary" if I don't go in each clone and click on restart, they will never leave.  In addition, even if I manually restart each workstation, they will remain in limbo forever customization.  Any ideas?

  Have you seen this KB, http://kb.vmware.com/kb/1026895? You must use a KMS server.

• I have two computers in Windows 7 which will not each other on my network. All other computers will see and can share files, but they connect between them.

  My HP laptop has installed Win7 Ult, the Fujitus Win7 Pro.

  Both computers were sharing the files back, outside a residential group, for a period of time. One day, they are stopped. No changes have been made to computers. I tried a restore of the system on each of them, and it did not help. I re windows loaded on the HP and that did not help. I don't think that it is only a permission of the questions that I used a windows machine 7 third to map actions to each of the individual laptops using their respective IDs. I can transfer files from one of them the "machine in the middle", then the action of the other, or as a copy/paste between them directly.

  WSD and NetBT will not solve one machine for others, but all other computers on the network will dispay on each machine. Only, they refuse to see each other. I have disabled the firewall. Password protected sharing, ensured that all netbios in the registry settings are correct. Pings between them are inaccessible returnded.

  Any help would be appreciated.

  Thank you!

  Hi Jonathan,.

  I see that you two computers on the network cannot see each other. I'll help you with this problem.

  1. don't you make changes to the computers?

  2 are computers on a domain network?

  3. do you have a router connected to these computers?

  Method 1:

  Open the HomeGroup troubleshooter

  http://Windows.Microsoft.com/en-us/Windows7/open-the-HomeGroup-Troubleshooter

  Method 2.

  Make sure that the following services are enabled on the computer.

  (a) click Start, type "services.msc" in the search and click on services. Verify that these services are enabled:

  -TCP/IP NetBIOS Helper service

  -DNS Client

  -Function Discovery Resource Publication

  -SSDP Discovery

  -UPnP device host

  To start the service and set it to automatic, follow these steps:

  (b) right click on each of the services listed above and click Properties.

  (c) click the general tab, and then, next to startup type, select automatic.

  (d) click on apply and then click Start.

  Method 3.

  I suggest you follow the steps in this article.

  Enable or disable network discovery: http://windows.microsoft.com/en-US/windows7/Enable-or-disable-network-discovery

  Method 4:

  Why can't I connect to other computers?

  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-other-computers

  Refer.

  Homegroup:

  http://Windows.Microsoft.com/en-CA/Windows7/products/features/HomeGroup

  Let us know if you need assistance with any windows problem. We will be happy to help you.