Allow traffic from port 80 to 1 single ip address

Similar Questions

• This allows traffic between two interfaces ethernet on a PIX

  I have a PIX with interface inside, IP 10.198.16.1. It also has an interface called WTS, IP 10.12.60.1. I'm having difficulty to allow traffic from the 10.198.16.0 network to cross the PIX in 10.12.60.0. I'm trying specifically to allow access to a server with an IP address of 10.12.60.2.

  I enclose my config. Any help would be greatly appreciated!

  OK, so the inside interface has a security level of 100, WTS has a security level of 75, so traffic from inside to WTS is considered outbound traffic, which is allowed by default. All you need is a pair of nat/global (or static) between both interfaces so that the PIX knows how NAT traffic between two interfaces (remember, the PIX do NAT).

  You have this in your config file:

  NAT (inside) 1 10.0.0.0 255.0.0.0 0 0

  who says all traffic inside, interface with the IP 10.x.x.x address will be NAT would have, but you must then a global for the interface WTS define what those IPS will be NAT would.

  Adding:

  Global (WTS) 1 interface

  will be PAT all inside resolves the IP address of the interface WTS and allow traffic to flow between the interfaces. If you prefer the hosts inside the interface to appear as their own IP address on the WTS network, then you can use a static command and NAT addresses themselves, actually doing NAT, but not actually change addresses:

  static (inside, WTS) 10.198.16.1 10.198.16.1 netmask 255.255.240.0

  Hope that helps.

• Catch 22 - Port Trunk Configurations: how to combine identifiers VLAN native with DHCP (but allows traffic of VM)

  Catch 22 - Port Network Configurations: how to combine identifiers VLAN native with DHCP (but allow the virtual computer)

  I came across a Catch 22.  Maybe someone can restore the directly here.  I found a "witch hunt" for sure.

  It comes with the Ports of junction on the side of the switch of the ESX host network.

  Context:

  Ok. The Setup is a HP Blade C7000 enclosure.  I try to configure ports for switching to the blades.  ESX 3.5 U4 will be installed the BL460cs.  Installation is preferred method: revive unattended.  No problem with the syntax of Kick-Start,

  I am here, it's the side network.

  The problem:

  I find a major complication in that the switch ports must be configured for both traffic Service Console and VMkernel, more Virtual Machine since only two NICs by blade. Not best practices, but we have only two switches Cisco 3020 inside.  The two uplink physical NIC is paired in the same vSwitch.  (No iSCSI does fortunately).

  So the Catch 22 question is as follows:

  If the id VLAN native set up on the switch port, DHCP works of course and the VMware boot loader is able to grasp a binary / packets on the network (FTP Site) and install OK.  But after no installation, no communication with SC unless I set the VLAN id of the SC to '0 '.  The value "4" 0 does not communication, but "40" is the VLAN native.

  If id configuring VLAN native retired from the Switch port, DHCP will not work and host does not have IP address during the VMware boot process.  This is as expected as traffic without label is not assigned an eligible

  VLAN, so no comms.

  The Port of the Switch configuration:

  interface GigabitEthernet0/16

  SERVERNAME description

  switchport trunk encapsulation dot1q

  switchport trunk vlan native 40

  switchport trunk allowed vlan 40-254

  switchport mode trunk

  switchport nonegotiate

  Speed 1000

  No cdp enable

  spanning tree portfast trunk

  end

  Summary

  OK, let's summarize where things are and if possible please attach responses to their digital identity.

  (1) is there a way to delete the VLAN tagging altogether side ESX host? Not only the id '0 '. The problem is with clearly with the VLAN native defined as "40".  If "40" IDs specified on the Group of ports for the Service Console, no joy, no comms. If the id of '0' value, capable of ping gateway and communicate on the network.

  (2) what is the problem with the definition of VLAN native as "40" when the config for the switch port is set as VLAN native "40"?  Or if it was a problem?  Both parameters clearly do not work together.

  (3) a switch receiving a unmarked frame it will assign to the VLAN Trunk native. Ok. Trunking bases and why I need a VLAN specified on the port for DHCP native work.  But it seems that since the id VLAN is set manually even as VLAN native, closed communications and no traffic as possible.

  (4) executives made tag 802. 1 q VLAN native?  I think that it is not and this could well be the problem. Since the id VLAN "40" is not labeled, but try to score the side host vSwitch port group.

  Please let me know your thoughts, community and how in general, we are approaching 2 NIC ESX configurations.

  When trunking multiple VLANs, you either have a default VLAN is nothing is tagged, or you don't.  That's what the vlan native to you, it defines which VLAN would be used if no tag is visible on the packets traversing the network.  For servers, if you are marking, then everything has to tag, if you're not marking at the server level, then the port must be either an access port or a VLAN native or default must be set.  I also don't keep your service console the same network as your vm.  Keep this isolated for the security of the network.  If you isolate this VLAN, you can separate and use a single IP address for installation and one for post construction.

  Or, you can provide an IP address during the build.

  -KjB

  VMware vExpert

• rv220 allow traffic on a port magnified

  Hello

  This should be a simple.  I am in my rv220, and the title of port forwarding, I created a rule.  I also created a personalized service for the particular port I want to allow traffic.  The problem is I want traffic to go to any computer on the local network.  What ip address I put as a destination.  I tried to put on a show, but it did not.  192.168.1.255. what I just put in the IP of the router LAN and it will do the rest?

  Please notify.

  Tony

  Hi Tony,.

  Packets transmitted by the WAN port are unicast. Broadcast packets are filtered and not allowed to the local network by default. No option in RV220 to rewrite a unicast packet to disseminate.

  There is only IGMP multicast support on this router, but I guess you do not speak on this subject.

  Normally with only firewall rule, you can allow traffic for a specific service to enter, WAN, LAN, but more NAT will be a problem.

  You can share the service you're trying to broadcast in the local network?

  Kind regards

  Bismuth

• Error iTunes - iTunes could not connect to the store purchases - if you have any firewall software, make sure it has been set to allow communication on port 443.

  My itunes has been fine. All of a sudden today it now gives me this error: error Itunes - iTunes could not connect to the store purchases - if you have a software firewall, make sure that it has been set to allow communication on port 443.

  I do not have my firewall active. I connected to itunes, quit itunes, reconnected - still a problem.

  Was there an update and now it's a bug? Help!

  Thank you!

  Run the Console application in one of the following ways:

  ☞ Enter the first letters of his name in a Spotlight search. Select from the results (it should be at the top).

  ☞ In the Finder, select go utilities ▹ of menu bar or press the combination of keys shift-command-U. The application is in the folder that opens.

  ☞ Open LaunchPad and start typing the name.

  The title of the Console window should be all Messages. If it isn't, select

  SYSTEM LOG QUERIES ▹ all Messages

  in the list of logs on the left. If you don't see this list, select

  List of newspapers seen ▹ display

  in the menu at the top of the screen bar.

  Click on the clear view icon in the toolbar. Then take an action that does not work the way you expect. Select all of the lines that appear in the Console window. Copy to the Clipboard by pressing Control-C key combination. Paste into a reply to this message by pressing command + V.

  The journal contains a large amount of information, almost everything that is not relevant to solve a particular problem. When you post a journal excerpt, be selective. A few dozen lines are almost always more than enough.

  Please don't dump blindly thousands of lines in the journal in this discussion.

  Please do not post screenshots of log messages - text poster.

  Some private information, such as your name or e-mail address, can appear in the log. Anonymize before posting.

  When you post the journal excerpt, an error message may appear on the web page: "you include content in your post that is not allowed", or "the message contains invalid characters." It's a bug in the forum software. Thanks for posting the text on Pastebin, then post here a link to the page you created.

  If you have an account on Pastebin, please do not select private in exposure menu to paste on the page, because no one else that you will be able to see it.

• Tunnel VPN L2L with NATTing will not allow traffic which will be initiated by spoke to the hub.

  Traffic from internal hosts will NAT address works ok, but what speaks tests it traffic never connects.

  get the 10.1.12.232 NAT host would be 172.27.63.133 and past through the VPN tunnel to 10.24.4.65 without problem. However when 10.24.4.65 tries to ping or connect to 172.27.63.133 traffic does not make inside host 10.1.12.232

  ASA-1 #.
  !
  network object obj - 172.27.73.0
  172.27.73.0 subnet 255.255.255.0
  network object obj - 172.27.63.0
  172.27.63.0 subnet 255.255.255.0
  network object obj - 10.1.0.0
  10.1.0.0 subnet 255.255.0.0
  network object obj - 10.24.4.64
  subnet 10.24.4.64 255.255.255.224
  network object obj - 172.27.73.0 - 172.27.73.255
  range 172.27.73.0 172.27.73.255
  the object of the 10.0.0.0 network
  subnet 10.0.0.0 255.0.0.0
  network object obj - 24.173.237.212
  Home 24.173.237.212
  network object obj - 10.1.12.232
  Home 10.1.12.232
  network object obj - 172.27.63.133
  Home 172.27.63.133
  the DM_INLINE_NETWORK_9 object-group network
  object-network 10.0.0.0 255.255.255.0
  object-network 10.0.11.0 255.255.255.0
  object-network 10.0.100.0 255.255.255.0
  object-network 10.0.101.0 255.255.255.0
  object-network 10.0.102.0 255.255.255.0
  object-network 10.0.103.0 255.255.255.0
  the DM_INLINE_NETWORK_16 object-group network
  object-network 10.1.11.0 255.255.255.0
  object-network 10.1.12.0 255.255.255.0
  object-network 10.1.13.0 255.255.255.0
  object-network 10.1.3.0 255.255.255.0
  !
  outside_1_cryptomap list extended access permitted ip object-group DM_INLINE_NETWORK_16-group of objects DM_INLINE_NETWORK_9
  access extensive list ip 172.27.73.0 outside_8_cryptomap allow 255.255.255.0 10.24.4.64 255.255.255.224
  access extensive list ip 172.27.63.0 outside_8_cryptomap allow 255.255.255.0 10.24.4.64 255.255.255.224
  !
  list of allowed outside access extended ip 10.24.4.64 255.255.255.224 172.27.63.0 255.255.255.0
  list of allowed outside access extended ip 10.24.4.64 255.255.255.224 10.1.0.0 255.255.0.0
  list of allowed outside access extended ip 172.27.63.0 255.255.255.0 10.1.0.0 255.255.0.0
  !
  NAT (inside, all) source static obj - 172.27.73.0 obj - 172.27.73.0 destination static obj - 10.24.4.64 obj - 10.24.4.64 no-proxy-arp-search to itinerary
  NAT (inside, all) source static obj - 172.27.63.0 obj - 172.27.63.0 destination static obj - 10.24.4.64 obj - 10.24.4.64 no-proxy-arp-search to itinerary
  NAT (inside, outside) source dynamic obj - 10.66.0.0 obj - 172.27.73.0 - 172.27.73.255 destination static obj - 10.24.4.64 obj - 10.24.4.64
  NAT (inside, outside) source dynamic obj - 10.70.0.0 obj - 172.27.73.0 - 172.27.73.255 destination static obj - 10.24.4.64 obj - 10.24.4.64
  NAT (inside, outside) source dynamic obj - 10.96.228.0 obj - 172.27.73.0 - 172.27.73.255 destination static obj - 10.24.4.64 obj - 10.24.4.64
  NAT (inside, outside) source dynamic obj - 10.96.229.0 obj - 172.27.73.0 - 172.27.73.255 destination static obj - 10.24.4.64 obj - 10.24.4.64
  NAT (inside, outside) source dynamic obj - 192.168.5.0 obj - 172.27.73.0 - 172.27.73.255 destination static obj - 10.24.4.64 obj - 10.24.4.64
  NAT (inside, outside) source dynamic obj - 10.75.0.0 obj - 172.27.73.0 - 172.27.73.255 destination static obj - 10.24.4.64 obj - 10.24.4.64
  NAT (inside, outside) source dynamic obj - 10.11.0.0 obj - 172.27.73.0 - 172.27.73.255 destination static obj - 10.24.4.64 obj - 10.24.4.64
  NAT (inside, outside) source static obj - 10.1.3.37 obj - 10.71.0.37 destination static obj - 50.84.209.140 obj - 50.84.209.140
  NAT (inside, outside) source static obj - 10.1.3.38 obj - 10.71.0.38 destination static obj - 50.84.209.140 obj - 50.84.209.140
  NAT (inside, outside) source static obj - 10.1.12.232 obj - 172.27.63.133 destination static obj - 10.24.4.64 obj - 10.24.4.64
  NAT (inside, outside) source dynamic obj - 10.1.0.0 obj - 172.27.73.0 - 172.27.73.255 destination static obj - 10.24.4.64 obj - 10.24.4.64
  !
  NAT (exterior, Interior) source static obj - 10.24.4.64 obj - 10.24.4.64 destination static obj - 172.27.63.133 obj - 10.1.12.232
  NAT (outside, outside) source static obj - 10.24.4.64 obj - 10.24.4.64 destination static obj - 172.27.63.133 obj - 10.1.12.232

  the object of the 10.0.0.0 network
  NAT (inside, outside) dynamic obj - 24.173.237.212
  !
  NAT (VendorDMZ, outside) the after-service automatic source dynamic obj - 192.168.13.0 obj - 24.173.237.212
  outside access-group in external interface
  Route outside 0.0.0.0 0.0.0.0 24.173.237.209 1
  Route inside 10.1.0.0 255.255.0.0 10.1.10.1 1
  Route inside 10.2.1.0 255.255.255.248 10.1.10.1 1
  !
  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-3DES-SHA-DH2-esp-3des esp-sha-hmac
  Crypto ipsec pmtu aging infinite - the security association
  !
  card crypto GEMed 8 corresponds to the address outside_8_cryptomap
  card crypto GEMed 8 set peer 64.245.57.4
  card crypto GEMed 8 set ikev1 transform-set ESP-AES-256-SHA ESP-AES-256-MD5
  GEMed outside crypto map interface
  !
  : end
  ASA-1 #.

  Hello

  First of all, I would like to remove these two lines because they do nothing productive

  nat (outside,inside) source static obj-10.24.4.64 obj-10.24.4.64 destination static obj-172.27.63.133 obj-10.1.12.232nat (outside,outside) source static obj-10.24.4.64 obj-10.24.4.64 destination static obj-172.27.63.133 obj-10.1.12.232

  Then, I was running packet - trace to see what NAT rule actually hit you.

  packet-tracer input inside 10.1.12.232 12345 10.24.4.65 12345

• A PIX-to-PIX VPN can allow traffic in only one direction?

  Here is the configuration of the PIX 501 that accepts incoming VPN tunnels of the other PIX dynamic-ip.  Everything works very well, allowing traffic to flow both ways after that the tunnel rises.  But then I somehow limit or prevent the traffic that originates on the PIX (192.168.27.2) to go to other networks of PIX?  In other words, if a tunnel exists (192.168.3.0 to 192.168.27.0), I only want to allow network traffic to access the network 27.0 3.0, and I want to anyone on the network 27.0 access network 3.0.

  Thanks for any comments.

  pixfirewall # sh conf
  : Saved
  : Written by enable_15 at 13:29:50.396 UTC Saturday, July 3, 2010
  6.3 (4) version PIX
  interface ethernet0 car
  interface ethernet1 100full
  ethernet0 nameif outside security0
  nameif ethernet1 inside the security100
  activate the encrypted password
  encrypted passwd
  pixfirewall hostname
  .com domain name
  fixup protocol dns-maximum length 4096
  fixup protocol ftp 21
  fixup protocol h323 h225 1720
  fixup protocol h323 ras 1718-1719
  fixup protocol http 80
  fixup protocol they 389
  fixup protocol rsh 514
  fixup protocol rtsp 554
  fixup protocol sip 5060
  fixup protocol sip udp 5060
  fixup protocol 2000 skinny
  fixup protocol smtp 25
  fixup protocol sqlnet 1521
  fixup protocol tftp 69
  names of
  access-list 101 permit ip 192.168.27.0 255.255.255.0 10.10.10.0 255.255.255.0
  access-list 102 permit ip 192.168.27.0 255.255.255.0 10.10.0.0 255.255.0.0
  access-list 102 permit ip 192.168.27.0 255.255.255.0 192.168.3.0 255.255.255.0
  access-list 102 permit ip 192.168.27.0 255.255.255.0 192.168.7.0 255.255.255.0
  pager lines 24
  ICMP deny everything outside
  Outside 1500 MTU
  Within 1500 MTU
  IP address outside xxx.xxx.xxx.248 255.255.255.255
  IP address inside 192.168.27.2 255.255.255.0
  alarm action IP verification of information
  alarm action attack IP audit
  IP local pool ippool 10.10.10.1 - 10.10.10.254
  PDM logging 100 information
  history of PDM activate
  ARP timeout 14400
  NAT (inside) - 0 102 access list
  Route outside 0.0.0.0 0.0.0.0 xxx.xxx.xxx.1 1
  Timeout xlate 0:05:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
  Timeout, uauth 0:05:00 absolute
  GANYMEDE + Protocol Ganymede + AAA-server
  AAA-server GANYMEDE + 3 max-failed-attempts
  AAA-server GANYMEDE + deadtime 10
  RADIUS Protocol RADIUS AAA server
  AAA-server RADIUS 3 max-failed-attempts
  AAA-RADIUS deadtime 10 Server
  AAA-server local LOCAL Protocol
  No snmp server location
  No snmp Server contact
  SNMP-Server Community public
  No trap to activate snmp Server
  enable floodguard
  Permitted connection ipsec sysopt
  Crypto ipsec transform-set esp - esp-md5-hmac gvnset
  Crypto-map dynamic dynmap 10 transform-set gvnset
  gvnmap 10 card crypto ipsec-isakmp dynamic dynmap
  gvnmap interface card crypto outside
  ISAKMP allows outside
  ISAKMP key * address 0.0.0.0 netmask 0.0.0.0
  ISAKMP identity address
  ISAKMP keepalive 60
  ISAKMP nat-traversal 20
  part of pre authentication ISAKMP policy 9
  encryption of ISAKMP policy 9
  ISAKMP policy 9 md5 hash
  9 2 ISAKMP policy group
  ISAKMP policy 9 life 86400
  vpngroup address ippool pool gvnclient
  vpngroup dns 192.168.27.1 Server gvnclient
  vpngroup gvnclient wins server - 192.168.27.1
  vpngroup gvnclient by default-domain '.com'
  vpngroup split tunnel 101 gvnclient
  vpngroup idle 1800 gvnclient-time
  vpngroup password gvnclient *.
  Telnet 0.0.0.0 0.0.0.0 inside
  Telnet timeout 30
  SSH 0.0.0.0 0.0.0.0 outdoors
  SSH timeout 30
  management-access inside
  Console timeout 0
  Terminal width 80
  Cryptochecksum:
  pixfirewall #.

  Of course, without a doubt capable.

  You can configure the inside interface access list to deny traffic from 192.168.27.0/24 to 192.168.3.0/24, and then allow anything else.

  Example:

  access list for the Interior-acl deny ip 192.168.27.0 255.255.255.0 192.168.3.0 255.255.255.0

  the Interior-acl ip access list allow a whole

  group-access Interior-acl in the interface inside

  Hope that helps.

• I allow calls from verified contacts, but still receive unwanted calls

  in do not distrub, I allow calls from verified contacts, but always receive unwanted calls, I even got a call with my name in the caller ID!

  If you allow calls repeated under tension, then the telemarketers or who calls you are probably recall several times. As for the one with your name in the caller ID, I am one of those who earlier. Turns out be a telemarketing touting T-Mobile robot. I was incredibly ticked. So I got my carrier on the phone a few minutes asking them to open a trace. These calls are illegal.

  The foam of telemark will stop at nothing in their attempts to get through you.

• How can I fix it? "Money cannot connect to the store purchases.   If you have any firewall software, make sure it has been set to allow communication on port 443.

  This message p [ops upward when I run iTunes]

  Money cannot connect to the store purchases.

  If you have any firewall software, make sure it has been set to allow communication on port 443.

  How can I fix it?

  me too... same problem... just started

  iTunes can't connect to the store purchases.

  If you have any firewall software, make sure it has been set to allow communication on port 443.

  MacBook Pro, osx el cap 10.11.1, itunes 12.3.1.23

• iTunes can't connect to store purchases. allow communication on port 443

  iTunes can't connect to store purchases. the msg States allow communications on port 443. I did this and still get the same message

  I started having this problem today, I know its nothing I did wrong on my end, it was beautiful before glad im not the only one having this problem

• I use a server DNS Server 2008 and need to transmit the DNS lookup on a Linux server that only allows you to Port 3128 for DNS.

  Hello

  I use a server DNS Server 2008 and need to transmit the DNS lookup on a Linux server that only allows you to Port 3128 for DNS.

  How can I configure my DNS server to use this port for shipments?

  Thanks for your replies

  Marcus

  Hello

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.
   
  http://social.technet.Microsoft.com/forums/en-us/winserverNIS/threads
   
  Here are a few Server DNS forwarders. Links for refrence,
   
  http://TechNet.Microsoft.com/en-us/library/cc754941.aspx
   
  http://TechNet.Microsoft.com/en-us/library/cc731991.aspx
   
  I hope this helps.

• Export the contacts from Windows Mail in a single folder

  Original title: How can I export contacts from Windows Mail in a single folder. It seems that export all? Help!
  Trying to export contacts to a folder only in gmail, but cannot select one.

  Hello

  There is no option in Windows Mail to export a specific contact group.
  You can export all contacts to Excel and edit/print as you wish.
  Follow these steps to export the Windows Mail Contacts to Excel:
  a. open Windows Contacts by clicking on the Start button, all programs, and then clicking Windows Contacts.
  b. on the toolbar, click on export and then click on the CSV format.
  CSV (Comma Separated Values). It is a format of generic file used to export or import information to and from databases or spreadsheets.
  c. click Export, select a folder where you want to store your contacts in the new format and then click OK.
  d. when a message appears telling you that the contacts export process is complete, click OK and then click Close.

  See these articles for help:
  http://Windows.Microsoft.com/en-us/Windows-Vista/import-export-or-change-the-format-for-contacts

• 160N not allowing access to a single ip address please!

  My router does not allow access to a single ip address.  I have a site that I have ftp access to and everything was working fine until today.  I can't access ftp with all the software and the site will not be rendered.  I checked all implement.  I called the hosting company, ISP provider and is not on their end.  I went to another computer somewhere else and everything worked fine.  I hooked in directly to the modem and everything worked as it is supposed to.  All other websites work very well.  It must be the router.   I have reset the router to factory settings and set to update the firmware.  As I said, everything was working just fine and then suddenly everything that is on the IP 1 will not work.  Any help with my situation is appreciated.

  Since you have already reset your router and re-configured all the settings in this topic. When your computer is connected to the Linksys router, on your computer, open the window command prompt and try to ping the IP address that you're trying to make it work with your Linksys router and check if you have all the answers.

  If not then on your configuration page of the router, click on the Security tab and disable the SPI Firewall and uncheck "Filter anonymous Internet requests" and click on save settings...

  Once you are done with these settings, you can now try to ping the IP address and check if you have all the answers...

  NOTE: Turn off the firewall and Antivirus on your computer...

• Y at - it an application that allows printing from an iPod touch?

  Y at - it an app that will allow printing from an iPod Touch to a printer Photosmart HP 6510?

  Hello

  See this (right side):

  http://WWW8.HP.com/us/en/products/smart-phones-handhelds-calculators/mobile-apps/app_details.HTML?app=TCM:245 - 1044333 & platform = tcm:245 - 1044335

  Your printer MUST support this too.

  Kind regards.

• Update multiple columns from multiple tables in a single UPDATE request

  Hello

  I'm trying to figure if I'm heading in the right direction.

  I want to update multiple columns from multiple tables in a single UPDATE request. Also, I would like to update multiple columns in a table from the tables.

  Scenario 1

  UPDATE Table2, Table 3
  SET T2.Column1 = T1.Column1 
  ,T2.Column2 = T1.Column2
  ,T3.Column2 = T1.Column2
  FROM Table1 T1, Table2 T2, Table3 T3
  WHERE T1.id = T2.id
  and T1.id = T3.id
  
  

  Scenario 2

  UPDATE Table3
  SET T3.Column1 = T1.Column1 
  T3.Column2 = T1.Column2
  ,T3.Column3 = T2.Column3
  ,T3.Column4 = T2.Column4
  FROM Table1 T1, Table2 T2, Table3 T3
  WHERE T3.id = T1.id
  and T3.id = T2.id
  
  

  Hello

  For scenario 1, you must write separate instructions UPDATE table2 and table3.

  To guard against someone else change one of these tables while you act so you can copy all relevant data in a global temporary table and update this global temporary table table3.

  ENGAGE only when two tables have been changed.

  You can write a procedure or an INSTEAD OF trigger to do all this.

  For scenario 2, you can reference many tables that you need when new table3.  It might be more efficient and simpler to use the MERGER rather than UPDATED.  For example:

  MERGE INTO table3 dst

  WITH THE HELP OF)

  SELECT t1.id

  t1.column1

  t1.column2

  t2.column3

  t2.column4

  FROM table1 t1

  JOIN table2 t2 ON t1.id = t2.id

  )             src

  WE (dst.id = src_id

  WHEN MATCHED THEN UPDATE

  SET dst.column1 = src.column1

  dst.column2 = src.column2,

  dst.column3 = src.column3,

  dst.column4 = src.column4,

  ;