Any login problem VPN - ASA5510
Hi all
I'm simulate Anyconnect VPN connection in the laboratory. I have a problem when the Anyconnect VPN on ASA5510 configuration.
I can have a successful connection anyconnect but I can't ping my firewall IPs Interface while I'm in the connection.
ASA 5510
Outside intellectual property: 192.168.1.1/24
PC connected to the external Interface: 192.168.1.10/24
Domestic IP:10.10.10.1/24
PC connected inside the Interface: 10.10.10.100/24
Pool: 10.20.20.11 - 10.20.20.50/24
I have a VPN connection & the PC connected to the external Interface receives an IP address from the pool assigned (10.20.20.11 with the default gateway of 10.20.20.1). But I can't reach (ping/telent) to the ASA, even if I'm on the anyconnect VPN.
I think that this is mainly because NAT/routing issue...
Please find the attached file (with show execution & see the release of the version).
Thanks in advance.
Set "inside access management.
Sent by Cisco Support technique iPad App
Tags: Cisco Security
Similar Questions
-
Login problem VPN on PIX on the side of the inside of the n/w
I am tring to connect to the vpn server (pix) outside my laptop within the network.
I have routed ip vpn on pix515 and fine ping pix.but not able to ping of 3550 switch and computer laptop.
How to get the vpn ip Switch? as I don't know the mask of the ip...
I would also like to know... is their something extra that I need on pix or 3550?
Hello!
-What is the default gateway of your laptop?
-You do any kind of NAT on the PIX? What is NAT PAT, static or normal?
-Can you ping the inside of the PIX of the laptop?
There could be several problems to solve here.
(1) first of all, make sure that your laptop has access to the internet
(2) If you want to ping him make sure internet you have an ACL on the PIX like the one below:
i.e.
Allow Access - list icmp an entire TEST
TEST group access in the interface outside
Also make sure you have no access list applied inside the PIX
-Now, can you connect at all?
-When you connect to? Another PIX? Router? Hub?
If you pass by PAT make sure that you have this command on the PIX:
"fixup protocol esp-ike.
Please let me know if you can answer my questions, in this way, it would be easier to help you.
Frank
-
Are there any known problems with external battery for iPhone 6 s karim?
Are there any known problems with external battery for iPhone 6 s karim? Jackery of input: 5V / 2. 1a.
I had heard that some may damage internal parts of the phone.
I am interested in what Apple says rather than what says karim.
Thank you.
Jkim99 wrote:
Are there any known problems with external battery for iPhone 6 s karim? Jackery of input: 5V / 2. 1a.
I had heard that some may damage internal parts of the phone.
I am interested what said Apple rather than what it says karim.
Thank you.
There is no Apple here in this technical forum from user to user.
-
I would like to become an installer of 'trust' for any future problems. How can I go about it? Thank you
You may have permanently damaged your Windows installation, but it is difficult to decide this question, although an online forum such as this.
You should not have deleted the files of C:\Windows\winsxs\amd64_microsoft-windows-tabletpc (unless you were actually only removing shortcuts).
WinFix is generally regarded as malware--> http://www.spyware-techie.com/winfix-10-removal-guide
I don't use Windows Live Photo Gallery (assuming that's what you are referring), so for the best chance of getting help, you should ask a question here--> http://answers.microsoft.com/en-us/windowslive/forum/gallery-files?sort=lastreplydate&dir=desc&tab=threads&status=all&mod=&modAge=&advFil=&postedAfter=&postedBefore=&threadType=all&tm=1460601829025
Use an object as "Icons of WINSXS in Photo Gallery" and to include a link to this thread--> http://answers.microsoft.com/en-us/windows/forum/windows_7-files/i-would-like-to-become-a-trusted-installer-for-all/488de805-9ca7-4e7c-901f-4b995fe9a6aa?msgId=5890890b-04be-421b-b622-0f839a815360
While you wait for a reply here, follow these steps.
Open the Photo Gallery, then click on the 'File' menu (to the left of the 'Home' menu)
In the menu that opens, click on 'include file '.
In the window that says "Change how this library brings together its content" (one at a time) select every item other than 'My images' and 'Public Photo' and click on 'Remove' and then click OK.
-
Can I hire the CC Adobe as a person and use it in a business without generating any legal problems for the company? I'm in the Brazil and the Adobe Web site, that I have not found that everything related to the legislation, they apply in this country on this issue.
single user licenses allow you to use the adobe corporate programs and allow to sell the products that you create using adobe programs.
-
Hello
I have problems to display Lotus iNotes through Domino 8.5 correctly a page Web the VPN without client in my Cisco ASA5510.
One of our customers has implemented Lotus Domino 8.5 and have portals of the individual user so that the user can each access their e-mail, calendar, journals, debates, etc.. Everything works fine on the internal network, as well as on a real SSL VPN as Anyconnect client... it is the Web page of the VPN without client that gives me a problem.
The occurrence of beginning of questions when I configure a VPN page without client for users first access, fill in a username/password general name, and then they are taken to their first iNotes login page. The iNotes login page looks very good, and when they connect in iNotes everything seems fine. However, when they start clicking around in different tabs or to open an email (all nested in the VPN page without customer), things don't arise, and error occurred on the page of iNotes as "a problem has occurred that may have caused the operation to fail. When I click on "Show Console" to get more details, I'm presented with:
-----------------------------------------
Domino version 8.5.1FP3 (Windows NT/Intel)
$HaikuForm - 304.5
Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 6.1; WOW64; Trident/4.0; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729 .NET CLR 3.0.30729; Media Center PC 6.0; InfoPath.2;. NET4.0C)2010-07-30 12:31:13 a problem has occurred that may have caused the operation to fail.
2010-07-30 12:31:13 ' CSCO_Util.parse_url (...). path ' is null or not an object
2010-07-30 12:31:13 https:/// + CSCOL + / cte.js: 9
2010-07-30 12:31:13 [GBy]-[(token) {var c = HTMLParserUtils; if(this._cur_segment==null) {ADAPT] ([object Object])
30/07/2010 12:32:08 [dojo - 1.3.2] failed to load http://mail1.fake.comdomjs/dojo-1.3.2/dojo/... /IBM/iNotes/widget/layout/DWASidebarContainer.js with error: [object Error]
30/07/2010-12:32:08 a problem has occurred that may have caused the operation to fail.
30/07/2010 12:32:08 failed to load "ibm.iNotes.widget.layout.DWASidebarContainer"; Finally tried '... ' /IBM/iNotes/widget/layout/DWASidebarContainer.js
30/07/2010-12:32:08 https:/// CSCO + 00756767633A2F2F7A6E7679312E656E71706E616762612E70627A ++ / domjs/dojo-1.3.2/dojo/dojo.js: 20
30/07/2010 12:32:08 [GBy] - [(_51,_52) {_52 = this ._global_omit_module_check: _52; var _53 = this. _}]("ibm.iNotes.widget.layout.DWASidebarContainer")-----------------------------------------
Users cannot open emails or create new email, neither can they do a lot of other primary functions in iNotes through this VPN without client. Looks like the redirection to URL of the ASA's corrupting what you looking for the Domino server. It does not work very well unlike what documentation Cisco says is "optimized for Lotus iNotes.
Does anyone have any suggestions? , I like to stay out of the way using a single SSL certificate (loser 2-factor of authentication, and must make an exception of firewall directly on the server on the network) and stay out of the way using Anyconnect if I can help it. I also want to emphasize the iNotes specifically that gives me this problem, not the Lotus Notes client part full I could do work using Smart Tunnels.
Troubleshooting steps, I made:
DNS servers appropriate 1.) are defined in the firewall
2.) I tried both full / lite of iNotes and produce both the same mistakes.
(3.) I tried Firefox 3.6.8 IE6, IE8 on Windows 7 and Windows XP. I think I have slightly better results than other browsers Firefox, but it is not error-free.
4.) I studied corruption cookie by removing all the stories and turn off any browser plugins and accelerators
Thank you!
Have you tried to use the smart tunnels for the DWA bookmark? Can u also try mode lite with the active smart tunnel?
Also in the description of your problem, when you say produces better results than IE Firefox, this exactly what you get?
-
Homepage of vpn clientless ssl after login problem
Hi all
I have a problem with my vpn without customer portal.
I need to configure when a user connects via the portal, something that works very well, it ends up on the home page.
At the present time there ends up immediately on the anyconnect button.
With the home page, I say the first button that says 'home '.
Users should be able to click on "Web Applications", hereinafter 'House '.
Under 'Web Applications' users must have their button aswell "Anyconnect".
First of all, I wasn't able to make the portal "Anyconnect" button display in the menu.
Then after awhile, I realized that when dynamic access policy says "Unchanged" on the page "access method".
When you change this setting "Client Anyconnect" portal no yard is no longer, I find myself immediately at the start of the anyconnect client.
When you select 'Portal' get the page of the portal, but the menu anyconnect is missing.
When you select 'Time-by default-portal' I get the anyconnect button and all the other menus, which is good.
But I hold the home button to be the default.
And not the anyconnect, after login button immediately you get the anyconnect start page.
And then finally and most importantly, when you select 'Time-by default-Anyconnect' you login to the Web portal, anyconnect begins immediately in the menu.
Something we want the end user to manually (click on "Start Anyconnect") I mean!
I'm sure that DAP which forces because of the options above.
But what selection unchanged or anything that does not include Anyconnect, then the anyconnect button went...
I don't know what I can do to change that.
Am I missing something?
I would say that DAP is not necessary, but when I put everything in the DAP default by default, then the anyconnect button went into the menu...
Kind regards
Robin
Here is my configuration:
attributes of Group Policy GP_company_intranet_portal
value x.x.x.x WINS server
value x.x.x.x DNS server
Protocol-tunnel-VPN-client ssl clientless ssl
Split-tunnel-policy tunnelall
company.local value by default-field
value of IPP_SSLVPN01 address pools
WebVPN
the value of the URL - list BML_company_intranet_portal
Disable http proxy
AnyConnect Dungeon-Installer installed
AnyConnect ask to activate default webvpn
value of customization CO_company_intranet_portal
gzip http-comp
hidden actions no
activate ActiveX-relay
disable file entry
exploration of the disable files
disable the input URL
disable the auto-signon chip-tunnel
type tunnel-group TG_company_portal_localauth remote access
tunnel-group TG_company_portal_localauth webvpn-attributes
personalization CO_company_intranet_portal
allow group-url https://portal.company.be
xxxxxxxxxx of encrypted password 0 privilege testaccount user name
attributes of testaccount user name
VPN-group-policy GP_company_intranet_portal
Protocol-tunnel-VPN-client ssl clientless ssl
disable the password-storage
value of group-lock TG_company_portal_localauth
type of remote access service
Troubleshooting when you are connected to, just to check if the right group strategy is used:
FW-company # display webvpn vpn-sessiondb
Session type: WebVPN
User name: testaccount index: 510
Public IP address: x.x.x.x
Protocol: without customer
License: AnyConnect Premium
Encryption: 3DES hash: SHA1
TX Bytes: bytes 114897 Rx: 16087
Group Policy: GP_company_intranet_portal
Tunnel of Group: TG_company_portal_localauth
Connect time: 14:50:56 GMT + 2 Thursday, October 25, 2012
Time: 0 h: 00 m: 03 s
Inactivity: 0 h: 00 m: 00s
Result of the NAC: unknown
Map VLANS: VLAN n/a: no
Hi Robin,
You can try:
1. Please remove / disable the rules of RAP and keep only one by default with the default action and parameters (continue). This is to exclude the DAPs as the primary cause.
2 - GP_company_intranet_portal group policy attributes
WebVPN
AnyConnect ask no webvpn default
Let me know how it goes.
HTH.
Portu.
Please note all useful posts
-
RADIUS Auth Login and VPN is in conflict...
Hello
Im trying to setup a 7204 to authentication radius connection, even if the router is also configured with RADIUS for VPN access. How can I configure it for both using 2 raidus different servers? the connection through RADIUS works fine on another router, although this one does not have VPN access so there is no conflict.
My config:
/ * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;} rayon de serveur AAA groupe RADIUS_AUTH
Server x.x.3.11 auth-port 1645 acct-port 1646/ * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;} radius AAA authentication connexion networkaccess groupe local
/ * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;} groupe par défaut AAA autorisation exec RADIUS_AUTH if-authentifié
/ * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;} rayon-serveur hôte x.x.3.11 auth-port 1645 acct-port 1646 clé xxxxxx
line vty 0 15
/ * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;} login authentication networkaccess
The line below is used for VPN authentication:
RADIUS-server host x.x.8.12 auth-port 1812 acct-port 1813 key xxxxxx
AAA of authentication ppp default local
Ray of AAA to authenticate ppp vpdn groupAAA authorization network default local
RADIUS AAA authorization network vpdn group
Group AAA authorization auth-proxy default RADIUS
AAA accounting delay start
accounting AAA periodic update 5
start-stop radius group AAA accounting network defaultFor some reason, it does not. I can't access the router and authenticate via radius x.x.3.11 server. I think there is a conflict between the VPN and authentication of connection but im not sure how to solve this problem.
any help would be greatly appreciated.
"ray of aaa of ppp authentication vpdn group.
'radius of group' means 'take any server radius from the global list'.
Change it to 'group mygroup' and boom, you give it a subset of radius servers
-
Win7/Satellite P200D - Admin Login - problem with keyboard - password is not displayed
Hi all
My Satellite P200D has Vista Premium o/s, was about 5 years old now
Has worked well enough until the last of three months or more and developed a problem of restart.
Hit restart button and it stops, then after several attempts get it at startup and on the screen that shows the internal PC Repair or Normal startup mode option. The only way that I can get to the login screen is to click on Normal mode as the automatic repair option does not work.
Has decided to switch to Win7 to see if that would solve the problem.
Now there is another problem, and it's the login admin password screen. The cursor flashes and any attempt to type password does not visibly show the words you type.
Also tried and external usb keyboard does no difference
Help, please
Thank you
I have the Satellite P200D with Win7 32 bit and it works perfectly.
You have this keyboard problem when you start the operating system in safe mode?
-
1
Hello
Seems to me that configurations are for the most part very well. But of course, they may be different from those who has the remote site. We do not know what are the settings on the other site of this connection VPN L2L.
NAT0 has configuration of a line that is not necessary (line below)
permit access list extended ip lan - imp 255.255.255.0 inside_nat0_outbound 1.1.1.0 255.255.255.0
You can use the "package Tracker" on the side of the CLI to check what happens to first traffic
entry Packet-trace inside tcp 1.1.1.100 12345 192.168.1.100 80
I guess the address LAN IP is changed for some reason any so replace the IP addresses above with random IP of the LAN and LAN REMOTE if necessary addresses.
Issue the command above twice. If the second output always stops in VPN Phase DROP then there are a few problems on each side of the connection VPN L2L in configurations.
You can check the output of the following command after issuing the command "packet - trace" above also to check what is happening in phase 1 of the VPN L2L negotiations
ISAKMP crypto to show his
If that runs through then I would start looking for a problem with related configurations "crypto map" configurations.
-Jouni
-
ASA does not propagate any routes for VPN users
Good afternoon
I m a problem concerning the spread of the roads to authenticated VPN users through the asa tunnel-group.
I have a VPN-users-pool where my users receive their IP address, and after authentication and the tunnel is established the idea is that the user get to the networks defined in the following ACL:
access-list within the standard allow 10.1.0.0 255.255.0.0
access-list within the standard allow 192.168.15.0 255.255.224.0
Now, the problem is that, after the tunnel is set up the only way, that the user receives is the default route (which is not supposed to be sent). The user does not receive the roads specified in the ACL list above. It has not received the network mask and assumes one 8 netmask (given that the pool of network from where it receives the IP address is a class A network).
Network routing works as expected (when I add the static routes directly to PC users, everything works OK). It s just the matter of the ASA do not spread the roads as it should.
Here is my split tunneling settings:
attributes of Group Policy DefaultRAGroup
VPN-idle-timeout 1
Protocol-tunnel-VPN l2tp ipsec
disable the PFS
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value inside
(...)
attributes of Group Policy DfltGrpPolicy
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value inside
(...)
Any ideas?
I have apreciate your help
Best regards
Just a question, I see:
attributes of Group Policy DefaultRAGroup
Protocol-tunnel-VPN l2tp ipsec
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value inside
internal DefaultRAGroup_1 group strategy
attributes of Group Policy DefaultRAGroup_1
Split-tunnel-policy tunnelspecified
It looks like your policy
DefaultRAGroup_1 you set ACLs and the other doesn't seem to be for L2TP/IPSEC. How do you connect to the ASA, using L2TP/IPSEC or Cisco IPSEC client? In addition, if your users are devoted to this group policy:
DefaultRAGroup_1 it looks like the acl is missing for the split tunneling
-
Hi people,
My company wishes to set up a VPN between our situation in Sarajevo and Mostar. We have a Cisco 871w in Sarajevo, it is in production, and the other will also be a router Cisco in Mostar.
I'm not much configuration of Cisco routers so it was better for me to test the scenario in Packet Tracer, but it simply does not work.
I added the tracer package file (see attachment), so it would be great if someone could take a look and tell me where is the problem.
I'm not sure if the Cisco 871w supports this type of VPN or should I buy another router VPN?
Thanks in advance,
Damir
Thank you...
The problem is the NAT statement that you configured is not exempt crypto traffic. He gets PATed to the IP address that you configure on the NAT pool, and it does not match the ACL (ACL 101) crypto more, so this isn't the start of the VPN tunnel.
Here's what you need to set up:
Router Sarajevo:
access-list 120 deny ip 192.168.10.0 0.0.0.255 192.168.20.0 0.0.0.255
access-list 120 permit ip 192.168.10.0 0.0.0.255 any
no ip inside the pool overld nat overload source list 7
IP nat inside source list pool 120 overld overload
Router Mostar:
access-list 120 deny ip 192.168.20.0 0.0.0.255 192.168.10.0 0.0.0.255
access-list 120 allow ip 192.168.20.0 0.0.0.255 any
no ip inside the pool overld nat overload source list 7
IP nat inside source list pool 120 overld overload
I hope this helps.
-
Problem VPN ASA 5505 8.3 (1) a site
Hello
My problem is with VPN site-to-site. It's between ASA5505 8.3 (1) and Pix 501 6.3 (5). The tunnel is created between them and it's good, here you have the results to see the crypto ipsec's and isakmp his
ciscoasa # sh crypto isakmp his
ITS enabled: 1
Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
Total SA IKE: 1
1 peer IKE: 91.X.X.57
Type: L2L role: initiator
Generate a new key: no State: MM_ACTIVE
ciscoasa # sh crypto ipsec his
Interface: outside
Tag crypto map: outside_map, seq num: 1, local addr: 79.X.X.2
list of access vpn extended permit ip 192.168.10.0 255.255.255.0 192.168.11.0 255.255.255.0
local ident (addr, mask, prot, port): (192.168.10.0/255.255.255.0/0/0)
Remote ident (addr, mask, prot, port): (192.168.11.0/255.255.255.0/0/0)
current_peer: 91.X.X.57
#pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
#pkts decaps: 3757, #pkts decrypt: 3757, #pkts check: 3757
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, comp #pkts failed: 0, #pkts Dang failed: 0
success #frag before: 0, failures before #frag: 0, #fragments created: 0
Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0
#send errors: 0, #recv errors: 0
local crypto endpt. : 79.X.X.2/0, remote Start crypto. : 91.X.X.57/0
Path mtu 1500, fresh ipsec generals 74, media, mtu 1500
current outbound SPI: F1C2FD46
current inbound SPI: 1BCF8C49
SAS of the esp on arrival:
SPI: 0x1BCF8C49 (466586697)
transform: aes-256-esp esp-md5-hmac no compression
running parameters = {L2L, Tunnel}
slot: 0, id_conn: 376832, crypto-card: outside_map
calendar of his: service life remaining (KB/s) key: (4373665/20348)
Size IV: 16 bytes
support for replay detection: Y
Anti-replay bitmap:
0xFFFFFFFF to 0xFFFFFFFF
outgoing esp sas:
SPI: 0xF1C2FD46 (4056087878)
transform: aes-256-esp esp-md5-hmac no compression
running parameters = {L2L, Tunnel}
slot: 0, id_conn: 376832, crypto-card: outside_map
calendar of his: service life remaining (KB/s) key: (4374000/20348)
Size IV: 16 bytes
support for replay detection: Y
Anti-replay bitmap:
0x00000000 0x00000001
But the problem is, as you can see in a show crypto ipsec sa, there is now traffic to a remote network of ASA
#pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
I have a single device on the remote network sends data to a sysloger on the local network and it works fine, all received messages but not other way to traffic.
To make sure that I go see the Nat and packet - trace entry inside tcp 192.168.10.7 1024 192.168.11.250 80 and looks like SHEEP works very well and traffic is allowed, but still once anything gets into the tunnel of local network
Results
ciscoasa # sh nat
Manual NAT policies (Section 1)
1 (one) to (all) source static sheep sheep sheep destination static sheep
translate_hits = 0, untranslate_hits = 38770
2 (inside) for the service public static obj - the source (on the outside) TCP1433 TCP1433 79.X.X.5 192.168.10.7
translate_hits = 0, untranslate_hits = 95
3 (inside) to the source (external) static obj - 192.168.10.7 interface service zzz zzz
translate_hits = 0, untranslate_hits = 19
4 (inside) of the (whole) source static obj - 10.0.0.0 obj - 10.0.0.0 destination static obj - 192.168.2.0 obj - 192.168.2.0
translate_hits = 17, untranslate_hits = 0
5 (inside) of the (whole) source static obj - obj - static 192.168.10.0 192.168.10.0 obj - obj-destination 10.1.1.1 10.1.1.1
translate_hits = 134, untranslate_hits = 0
6 (inside) to the (whole) source static obj - 10.1.1.1 obj - 10.1.1.1 destination static obj - 192.168.10.0 obj - 192.168.10.0
translate_hits = 0, untranslate_hits = 0
7 (inside) of the (whole) source static obj - 192.168.0.0 obj - 192.168.0.0 destination static obj - 192.168.2.0 obj - 192.168.2.0
translate_hits = 172, untranslate_hits = 53
Auto NAT policies (Section 2)
1 (inside) (outside) source static obj - 192.168.10.3 service TCP 3389 3389 79.X.X.5
translate_hits = 12, untranslate_hits = 4823
2 (inside) (outside) source static obj - 192.168.10.5 79.X.X.3 DNS
translate_hits = 341869, untranslate_hits = 41531
3 (inside) (outside) source static obj - 192.168.10.3 - 01 79.X.X.5 service TCP 444 444
translate_hits = 0, untranslate_hits = 0
4 (inside) to the source (external) static obj - 192.168.10.7 tcp 3389 3389 service interface
translate_hits = 21, untranslate_hits = 751
5 (inside) (outside) source static obj - 192.168.10.7 - 02 interface tcp 8080 https service
translate_hits = 0, untranslate_hits = 100
6 (inside) (outside) source static obj - 192.168.10.11 79.X.X.5 TCP smtp smtp service
translate_hits = 2, untranslate_hits = 18838
7 (inside) (outside) source static obj - 192.168.10.11 - 01 udp 443 443 service 79.X.X.5
translate_hits = 0, untranslate_hits = 0
8 (inside) (outside) source static obj - 192.168.10.11 - 02 79.X.X.5 tcp https https service
translate_hits = 221, untranslate_hits = 9770
9 (inside) (outside) source static obj - 192.168.10.11 - 03 79.X.X.5 tcp https https service
translate_hits = 0, untranslate_hits = 0
10 (inside) (outside) source static obj - 192.168.10.15 79.X.X.5 service tcp www 81
translate_hits = 0, untranslate_hits = 34
11 (inside) (outside) source static obj - 192.168.10.26 79.X.X.5 service TCP 8080 8080
translate_hits = 9, untranslate_hits = 4407
12 (inside) (outside) source static obj - 192.168.10.26 - 01 79.X.X.5 tcp 8080 www service
translate_hits = 0, untranslate_hits = 578
13 (inside) (outside) source static obj - 192.168.10.220 79.X.X.6 service TCP 3389 3389
translate_hits = 0, untranslate_hits = 41
14 (inside) (outside) source static obj - 192.168.10.220 - 1 79.X.X.6 tcp https https service
translate_hits = 0, untranslate_hits = 3
15 (inside) to the obj_any interface dynamic source (external)
translate_hits = 410005, untranslate_hits = 144489
16 (invited) to dynamic interface of the source (outside) obj_any-01
translate_hits = 19712, untranslate_hits = 4490
ciscoasa # packet - trace entry inside tcp 192.168.10.7 1024 192.168.11.250 80
Phase: 1
Type: UN - NAT
Subtype: static
Result: ALLOW
Config:
NAT (any, any) source static sheep sheep sheep destination static sheep
Additional information:
NAT divert on exit to the outside interface
Untranslate 192.168.11.250/80 to 192.168.11.250/80
Phase: 2
Type: ACCESS-LIST
Subtype: Journal
Result: ALLOW
Config:
Access-group inside_out in interface inside
access-list extended inside_out permit ip 192.168.10.0 255.255.255.0 192.168.11.0 255.255.255.0
Additional information:
Direct flow from returns search rule:
ID = 0xd9886ae8, priority = 13, area = allowed, deny = false
hits = 18503, user_data = 0xd6581290, cs_id = 0 x 0, use_real_addr, flags = 0 x 0 = 0 protocol
IP/ID=192.168.10.0 SRC, mask is 255.255.255.0, port = 0
IP/ID=192.168.11.0 DST, mask is 255.255.255.0, port = 0, dscp = 0 x 0
input_ifc = output_ifc = any to inside,
Phase: 3
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional information:
Direct flow from returns search rule:
ID = 0xd80c87c8, priority = 0, sector = inspect-ip-options, deny = true
hits = 1047092, user_data = 0 x 0, cs_id = 0 x 0, reverse, flags = 0 x 0 = 0 protocol
IP/ID=0.0.0.0 SRC, mask is 0.0.0.0, port = 0
IP/ID=0.0.0.0 DST, mask is 0.0.0.0, port = 0, dscp = 0 x 0
input_ifc = output_ifc = any to inside,
Phase: 4
Type: NAT
Subtype:
Result: ALLOW
Config:
NAT (any, any) source static sheep sheep sheep destination static sheep
Additional information:
Direct flow from returns search rule:
ID = 0xd9859830, priority = 6, area = nat, deny = false
hits = 2107, user_data = 0xd83a9b48, cs_id = 0 x 0, use_real_addr, flags = 0 x 0 = 0 protocol
IP/ID=192.168.10.0 SRC, mask is 255.255.255.0, port = 0
IP/ID=192.168.11.0 DST, mask is 255.255.255.0, port = 0, dscp = 0 x 0
input_ifc = none, output_ifc = any
Phase: 5
Type: HOST-LIMIT
Subtype:
Result: ALLOW
Config:
Additional information:
Direct flow from returns search rule:
ID = 0xd8114d98, priority = 0, domain = host-limit, deny = false
hits = 674350, user_data = 0 x 0, cs_id = 0 x 0, flags = 0 x 0 = 0 protocol
IP/ID=0.0.0.0 SRC, mask is 0.0.0.0, port = 0
IP/ID=0.0.0.0 DST, mask is 0.0.0.0, port = 0, dscp = 0 x 0
input_ifc = output_ifc = any to inside,
Phase: 6
Type: VPN
Subtype: encrypt
Result: ALLOW
Config:
Additional information:
Direct flow from returns search rule:
ID = 0xd83a9960, priority = 70, domain = encrypt, deny = false
hits = 26732, user_data = 0xce165c, cs_id = 0xd83ad0e8, reverse, flags = 0 x 0 = 0 protocol
IP/ID=192.168.10.0 SRC, mask is 255.255.255.0, port = 0
IP/ID=192.168.11.0 DST, mask is 255.255.255.0, port = 0, dscp = 0 x 0
input_ifc = none, output_ifc = external
Phase: 7
Type: NAT
Subtype: rpf check
Result: ALLOW
Config:
NAT (any, any) source static sheep sheep sheep destination static sheep
Additional information:
Direct flow from returns search rule:
ID = 0xd98d1d70, priority = 6, area = nat-reversed, deny = false
hits = 1419, user_data = 0xd83a9b48, cs_id = 0 x 0, use_real_addr, flags = 0 x 0 = 0 protocol
IP/ID=192.168.10.0 SRC, mask is 255.255.255.0, port = 0
IP/ID=192.168.11.0 DST, mask is 255.255.255.0, port = 0, dscp = 0 x 0
input_ifc = none, output_ifc = any
Phase: 8
Type: VPN
Subtype: ipsec-tunnel-flow
Result: ALLOW
Config:
Additional information:
Reverse flow from returns search rule:
ID = 0xd9bda388, priority = 69 = ipsec-tunnel-flow area, deny = false
hits = 486, user_data is 0x13492cc, cs_id = 0 x 0, reverse, flags = 0 x 0 = 0 protocol
IP/ID=192.168.11.0 SRC, mask is 255.255.255.0, port = 0
IP/ID=192.168.10.0 DST, mask is 255.255.255.0, port = 0, dscp = 0 x 0
input_ifc = out, output_ifc = any
Phase: 9
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional information:
Reverse flow from returns search rule:
ID = 0xd8192ab0, priority = 0, sector = inspect-ip-options, deny = true
hits = 1169899, user_data = 0 x 0, cs_id = 0 x 0, reverse, flags = 0 x 0 = 0 protocol
IP/ID=0.0.0.0 SRC, mask is 0.0.0.0, port = 0
IP/ID=0.0.0.0 DST, mask is 0.0.0.0, port = 0, dscp = 0 x 0
input_ifc = out, output_ifc = any
Phase: 10
Type: CREATING STREAMS
Subtype:
Result: ALLOW
Config:
Additional information:
New workflow created with the 1293619 id, package sent to the next module
Information module for forward flow...
snp_fp_tracer_drop
snp_fp_inspect_ip_options
snp_fp_tcp_normalizer
snp_fp_translate
snp_fp_adjacency
snp_fp_encrypt
snp_fp_fragment
snp_ifc_stat
Information for reverse flow...
snp_fp_tracer_drop
snp_fp_inspect_ip_options
snp_fp_ipsec_tunnel_flow
snp_fp_translate
snp_fp_tcp_normalizer
snp_fp_adjacency
snp_fp_fragment
snp_ifc_stat
Result:
input interface: inside
entry status: to the top
entry-line-status: to the top
output interface: outside
the status of the output: to the top
output-line-status: to the top
Action: allow
It is a complete config for ASA
VPN
Network local 192.168.10.0/24
remote network 192.168.11.0/24
Config
:
ASA Version 8.3 (1)
!
ciscoasa hostname
domain.com domain name
activate the password * encrypted
passwd * encrypted
names of
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.10.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 79.X.X.2 255.255.255.248
!
interface Vlan12
prior to interface Vlan1
nameif comments
security-level 80
192.168.4.1 IP address 255.255.255.0
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
switchport access vlan 2
!
interface Ethernet0/6
!
interface Ethernet0/7
switchport access vlan 12
!
boot system Disk0: / asa831 - k8.bin
passive FTP mode
clock timezone GMT/UTC 0
summer time clock GMT/BDT recurring last Sun Mar 01:00 last Sun Oct 02:00
DNS domain-lookup outside
DNS server-group DefaultDNS
Server name 192.168.10.11
domain.com domain name
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
network object obj - 192.168.0.0
Subnet 192.168.0.0 255.255.0.0
network object obj - 192.168.2.0
Subnet 192.168.2.0 255.255.255.128
network object obj - 10.0.0.0
subnet 10.0.0.0 255.0.0.0
network object obj - 192.168.10.2
host 192.168.10.2
network object obj - 192.168.10.2 - 01
host 192.168.10.2
network object obj - 192.168.10.3
host 192.168.10.3
network object obj - 192.168.10.2 - 02
host 192.168.10.2
network object obj - 192.168.10.2 - 03
host 192.168.10.2
network object obj - 192.168.10.3 - 01
Home 192.168.10.7
network object obj - 192.168.10.5
host 192.168.10.5
newserver network object
Home 192.168.10.7
New SQL Server description
network object obj - 192.168.10.7
Home 192.168.10.7
network of the A_79.X.X.6 object
Home 79.X.X.6
network of the PublicServer_NAT1 object
Home 192.168.10.7
zzz service object
service source eq 1 65535 udp syslog destination range
Syslog description
purpose of the 79.X.X.5 network
Home 79.X.X.5
service of the TCP1433 object
destination service tcp source eq 1433 1 65535 range
Description TCP1433
network object obj - 192.168.10.220
Home 192.168.10.220
network object obj - 192.168.10.220 - 1
Home 192.168.10.220
network object obj - 192.168.10.222
Home 192.168.10.222
network object obj - 192.168.10.2 - 04
host 192.168.10.2
network object obj - 192.168.10.7 - 02
Home 192.168.10.7
network object obj - 192.168.10.11
Home 192.168.10.11
network object obj - 192.168.10.11 - 01
Home 192.168.10.11
network object obj - 192.168.10.11 - 02
Home 192.168.10.11
network object obj - 192.168.10.11 - 03
Home 192.168.10.11
network object obj - 192.168.10.26
Home 192.168.10.26
network object obj - 192.168.10.26 - 01
Home 192.168.10.26
network object obj - 192.168.10.15
Home 192.168.10.15
network object obj - 192.168.10.11 - 04
Home 192.168.10.11
network object obj - 10.1.1.1
host 10.1.1.1
network object obj - 192.168.10.0
192.168.10.0 subnet 255.255.255.0
network object obj - 192.168.10.220 - 2
Home 192.168.10.220
network vpn-local object
192.168.10.0 subnet 255.255.255.0
object network vpn - ru
subnet 192.168.11.0 255.255.255.0
network obj_any object
subnet 0.0.0.0 0.0.0.0
network obj_any-01 object
subnet 0.0.0.0 0.0.0.0
object-group service syslog udp
Service Description syslog group
port-object eq syslog
object-group service udp zzzz
port-object eq syslog
object-group service sss udp
port-object eq syslog
object-group network sheep
object-network 192.168.10.0 255.255.255.0
object-network 192.168.11.0 255.255.255.0
object-network 192.168.3.0 255.255.255.0
outside_all of access allowed any ip an extended list
VPN_splitTunnelAcl list standard access allowed 192.168.0.0 255.255.0.0
VPN_splitTunnelAcl list standard access allowed 10.0.0.0 255.0.0.0
permit inside_nat0_outbound to access extended list ip 192.168.0.0 255.255.0.0 192.168.2.0 255.255.255.128
inside_nat0_outbound to access ip 10.0.0.0 scope list allow 255.0.0.0 192.168.2.0 255.255.255.128
access-list extended inside_out allow ip 192.168.11.0 255.255.255.0 192.168.10.0 255.255.255.0
access-list extended inside_out permit ip 192.168.10.0 255.255.255.0 192.168.11.0 255.255.255.0
scope of the inside_out to the list of permitted any one ip access
inside_out to the access list extended 192.168.11.0 allowed any ip 255.255.255.0
inside_out to the list of access permit tcp host 192.168.10.2 any eq smtp
inside_out to the list of access permit tcp any any eq smtp
access-list extended inside_out allow udp 192.168.10.0 255.255.255.0 host 10.1.1.1
access-list extended inside_out permit udp host 10.1.1.1 192.168.10.0 255.255.255.0
inside_out to the list of allowed extensive access icmp host 192.168.10.7 all
inside_out to the list of allowed extensive access a whole icmp
outside_zzz list of allowed ip extended access any external interface
outside_zzz list extended access permit tcp host 87.X.X.73 host 79.X.X.5 eq 1433
outside_zzz tcp extended access list refuse any host 79.X.X.5 eq 1433
outside_zzz list extended access permitted tcp 207.126.144.0 255.255.240.0 eq 79.X.X.5 the smtp host
outside_zzz tcp extended access list refuse any host 79.X.X.5 eq smtp
outside_zzz access-list extended permit ip any host 79.X.X.5
outside_zzz of access allowed any ip an extended list
permit access list extended ip 192.168.10.0 outside_in 255.255.255.0 192.168.11.0 255.255.255.0
access extensive list ip 192.168.11.0 outside_in allow 255.255.255.0 192.168.10.0 255.255.255.0
access extensive list ip 192.168.11.0 outside_in allow 255.255.255.0 any
outside_in list extended access permit tcp any host 192.168.10.15 eq 81
outside_in list extended access permit ip any host 192.168.10.5
access-list outside_in extended permit ip any host 79.X.X.4
outside_in list extended access permit tcp host 82.X.X.166 host 192.168.10.7 eq 1433
outside_in list extended access permit tcp host 84.X.X.30 host 192.168.10.7 eq 1433
outside_in list extended access tcp refuse any host 192.168.10.7 eq 1433
outside_in list extended access permit tcp any host 192.168.10.3 eq 444
outside_in list extended access permitted tcp 207.126.144.0 255.255.240.0 host 192.168.10.11 eq 444
outside_in list extended access permitted tcp 207.126.144.0 255.255.240.0 eq smtp host 192.168.10.11
outside_in list extended access permitted tcp 207.126.144.0 255.255.240.0 host 192.168.10.2 eq smtp
outside_in list extended access tcp refuse any host 192.168.10.11 eq smtp
outside_in list extended access tcp refuse any host 192.168.10.2 eq smtp
outside_in list extended access permit tcp any host 192.168.10.2 eq smtp
outside_in list extended access permit udp any host 192.168.10.2 eq 443
outside_in list extended access permit tcp any host 192.168.10.3 eq 3389
outside_in list extended access permit tcp any host 192.168.10.2 eq 4125
outside_in list extended access permit tcp any host 192.168.10.11 eq https
outside_in list extended access permit tcp any host 192.168.10.2 eq https
outside_in list extended access allowed esp all the host 91.X.X.57
outside_in list extended access permit tcp any host 192.168.10.3 eq 1433
access-list extended outside_in permit ip host 91.X.X.57 all
access-list outside_in extended permit ip any host 79.X.X.5
access-list outside_in extended permit ip any host 79.X.X.2
outside_in list extended access permit tcp any host 79.X.X.6 eq 3389
outside_in list extended access permit tcp any host 192.168.10.220 eq 3389
outside_in list extended access permit tcp any host 79.X.X.5 eq 81
access extensive list permits all ip a outside_in
outside_in list extended access permit tcp host 91.X.X.178 host 192.168.10.7 eq 1433
outside_in list extended access permit tcp host 87.X.X.73 host 192.168.10.7 eq 1433
access-list extended qnap permit ip host 192.168.10.26 all
access-list extended qnap permit ip any host 192.168.10.26
phone_bypass list extended access allowed host 10.1.1.1 ip 192.168.10.0 255.255.255.0
permit phone_bypass to access extended list ip 192.168.10.0 255.255.255.0 host 10.1.1.1
phone_bypass list extended access allowed host 10.1.1.1 ip 192.168.2.0 255.255.255.0
phone_bypass to access extended list ip 192.168.2.0 allow 255.255.255.0 host 10.1.1.1
list of access vpn extended permit ip 192.168.10.0 255.255.255.0 192.168.11.0 255.255.255.0
extended vpn 192.168.11.0 ip access list allow 255.255.255.0 192.168.10.0 255.255.255.0
pager lines 24
Enable logging
exploitation forest-size of the buffer 1024000
logging asdm-buffer-size 512
logging buffered information
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
Comments of MTU 1500
mask of local pool RemoteVPN 192.168.2.20 - 192.168.2.100 IP 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any inside
ICMP allow all outside
ASDM image disk0: / asdm - 631.bin
enable ASDM history
ARP timeout 14400
NAT (any, any) source static sheep sheep sheep destination static sheep
NAT source service (Interior, exterior) static obj - 192.168.10.7 79.X.X.5 TCP1433 TCP1433
NAT (inside, outside) source static obj - 192.168.10.7 interface service zzz zzz
NAT (inside, all) source static obj - 10.0.0.0 obj - 10.0.0.0 destination static obj - 192.168.2.0 obj - 192.168.2.0
NAT (inside, all) source static obj - 192.168.10.0 obj - 192.168.10.0 destination static obj - 10.1.1.1 obj - 10.1.1.1
NAT (inside, all) source static obj - 10.1.1.1 obj - 10.1.1.1 destination static obj - 192.168.10.0 obj - 192.168.10.0
NAT (inside, all) source static obj - 192.168.0.0 obj - 192.168.0.0 destination static obj - 192.168.2.0 obj - 192.168.2.0
!
network object obj - 192.168.10.3
NAT (inside, outside) static service tcp 3389 3389 79.X.X.5
network object obj - 192.168.10.3 - 01
NAT (inside, outside) static 79.X.X.5 tcp 444 444 service
network object obj - 192.168.10.5
NAT (inside, outside) public static dns 79.X.X.3
network object obj - 192.168.10.7
NAT (inside, outside) interface static service tcp 3389 3389
network object obj - 192.168.10.220
NAT (inside, outside) static service tcp 3389 3389 79.X.X.6
network object obj - 192.168.10.220 - 1
NAT (inside, outside) static 79.X.X.6 tcp https https service
network object obj - 192.168.10.7 - 02
NAT (inside, outside) interface static tcp 8080 https service
network object obj - 192.168.10.11
NAT (inside, outside) static 79.X.X.5 tcp smtp smtp service
network object obj - 192.168.10.11 - 01
NAT (inside, outside) udp 443 443 service 79.X.X.5 static
network object obj - 192.168.10.11 - 02
NAT (inside, outside) static 79.X.X.5 tcp https https service
network object obj - 192.168.10.11 - 03
NAT (inside, outside) static 79.X.X.5 tcp https https service
network object obj - 192.168.10.26
NAT (inside, outside) static 79.X.X.5 8080 8080 tcp service
network object obj - 192.168.10.26 - 01
NAT (inside, outside) static 79.X.X.5 tcp 8080 www service
network object obj - 192.168.10.15
NAT (inside, outside) static 79.X.X.5 tcp 81 www service
network obj_any object
NAT dynamic interface (indoor, outdoor)
network obj_any-01 object
NAT dynamic interface (guest, outdoor)
Access-group inside_out in interface inside
Access-group outside_in in external interface
Route outside 0.0.0.0 0.0.0.0 79.X.X.1 1
Route inside 10.0.0.0 255.0.0.0 192.168.10.4 1
Route outside 10.1.1.1 255.255.255.255 192.168.10.4 1
Route outside 192.168.11.0 255.255.255.0 79.X.X.2 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
RADIUS Protocol RADIUS AAA server
reactivation impoverishment deadtime mode 1
AAA-server RADIUS (inside) host 192.168.10.7
key *.
AAA authentication http LOCAL console
the ssh LOCAL console AAA authentication
LOCAL AAA authorization command
http server enable 444
http 0.0.0.0 0.0.0.0 inside
http 0.0.0.0 0.0.0.0 outdoors
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
No vpn sysopt connection permit
Service resetoutside
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-SHA 256 - aes - esp esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto-map dynamic outside_dyn_map pfs set 20 Group1
Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA
card crypto outside_map 1 match for vpn
outside_map game 1 card crypto peer 91.X.X.57
card crypto outside_map 1 set of transformation-ESP-AES-SHA
outside_map map 1 lifetime of security association set seconds 28800 crypto
card crypto outside_map 1 set security-association life kilobytes 4608000
map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
outside_map interface card crypto outside
crypto isakmp identity address
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
lifetime 28800
Crypto isakmp nat-traversal 3600
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 inside
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 30
Console timeout 0
dhcpd dns 83.X.X.8 83.X.X.10
dhcpd outside auto_config
!
dhcpd address 192.168.10.50 - 192.168.10.100 inside
dhcpd dns 83.X.X.8 83.X.X.10 interface inside
dhcpd lease interface 600 inside
dhcpd interface to domain.com domain inside
!
Reviews of dhcpd address 192.168.4.50 - 192.168.4.100
Dhcpd lease 600 interface comments
Comments enable dhcpd
!
priority queue inside
priority-queue outdoors
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
NTP 93.170.32.1 Server
NTP 93.170.32.2 Server
NTP 89.145.68.17 Server prefer
WebVPN
allow outside
SVC image disk0:/anyconnect-win-2.4.1012-k9.pkg 1 regex 'Windows NT'
SVC image disk0:/anyconnect-wince-ARMv4I-2.4.1012-k9.pkg 2 regex "Windows CE"
enable SVC
Auto-signon allow ip 192.168.0.0 255.255.0.0 basic auth-type
internal l2l group policy
attributes of the l2l group policy
VPN-idle-timeout no
Protocol-tunnel-VPN IPSec
attributes of Group Policy DfltGrpPolicy
value of server DNS 192.168.10.11
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list VPN_splitTunnelAcl
value by default-field DOMAINl.local
internal VPNv group strategy
attributes of Group Policy VPNv
value of server DNS 192.168.10.11
Protocol-tunnel-VPN IPSec webvpn
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list VPN_splitTunnelAcl
field default value domain.com
password username test * encrypted privilege 0
username test attributes
VPN-group-policy VPNv
ID password cisco * encrypted
roger password username * encrypted privilege 15
attributes global-tunnel-group DefaultRAGroup
address pool RemoteVPN
attributes global-tunnel-group DefaultWEBVPNGroup
address pool RemoteVPN
Group-LOCAL RADIUS authentication server
type tunnel-group VPNv remote access
attributes global-tunnel-group VPNv
address pool RemoteVPN
Group-LOCAL RADIUS authentication server
Group Policy - by default-VPNv
IPSec-attributes tunnel-group VPNv
pre-shared key *.
tunnel-group testgroup type remote access
tunnel-group testgroup General attributes
management of the password password-expire-to-days 90
tunnel-group 91.X.X.57 type ipsec-l2l
IPSec-attributes tunnel-group 91.X.X.57
pre-shared key *.
!
Global class-card class
match default-inspection-traffic
class-map qnap_band
corresponds to the list of access qnap
The class-card phone
corresponds to the phone_bypass access list
!
!
Policy-map global_policy
Global category
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Policy-map qnap_access
class qnap_band
512000 64000 police entry
512000 64000 release of police
phone class
set the advanced options of the tcp-State-bypass connection
World-Policy policy-map
Global category
inspect the dns
inspect the ftp
inspect the pptp
inspect the rtsp
inspect the sip
inspect the skinny
Policy-map phone_bypass_policy
phone class
set the advanced options of the tcp-State-bypass connection
!
service-policy-international policy global
service-policy qnap_access to the inside interface
privilege level 3 mode exec cmd command perfmon
privilege level 3 mode exec cmd ping command
mode privileged exec command cmd level 3
logging of the privilege level 3 mode exec cmd commands
privilege level 3 exec command failover mode cmd
privilege level 3 mode exec command packet cmd - draw
privilege level 5 see fashion exec running-config command
order of privilege show level 3 exec mode reload
privilege level 3 exec mode control fashion show
privilege see the level 3 exec firewall command mode
privilege see the level 3 exec mode command ASP.
processor mode privileged exec command to see the level 3
privilege command shell see the level 3 exec mode
privilege show level 3 exec command clock mode
privilege exec mode level 3 dns-hosts command show
privilege see the level 3 exec command access-list mode
logging of orders privilege see the level 3 exec mode
privilege, level 3 see the exec command mode vlan
privilege show level 3 exec command ip mode
privilege, level 3 see fashion exec command ipv6
privilege, level 3 see the exec command failover mode
privilege, level 3 see fashion exec command asdm
exec mode privilege see the level 3 command arp
command routing privilege see the level 3 exec mode
privilege, level 3 see fashion exec command ospf
privilege, level 3 see the exec command in aaa-server mode
AAA mode privileged exec command to see the level 3
privilege see the level 3 exec mode command crypto
privilege, level 3 see fashion exec command vpn-sessiondb
privilege level 3 exec mode command ssh show
privilege, level 3 see fashion exec command dhcpd
privilege, level 3 see the vpnclient command exec mode
privilege, level 3 see fashion exec command vpn
privilege level see the 3 blocks from exec mode command
privilege, level 3 see fashion exec command wccp
privilege, level 3 see the exec command in webvpn mode
privilege control module see the level 3 exec mode
privilege, level 3 see fashion exec command uauth
privilege see the level 3 exec command compression mode
level 3 for the show privilege mode configure the command interface
level 3 for the show privilege mode set clock command
level 3 for the show privilege mode configure the access-list command
level 3 for the show privilege mode set up the registration of the order
level 3 for the show privilege mode configure ip command
level 3 for the show privilege mode configure command failover
level 5 mode see the privilege set up command asdm
level 3 for the show privilege mode configure arp command
level 3 for the show privilege mode configure the command routing
level 3 for the show privilege mode configure aaa-order server
level mode 3 privilege see the command configure aaa
level 3 for the show privilege mode configure command crypto
level 3 for the show privilege mode configure ssh command
level 3 for the show privilege mode configure command dhcpd
level 5 mode see the privilege set privilege to command
privilege level clear 3 mode exec command dns host
logging of the privilege clear level 3 exec mode commands
clear level 3 arp command mode privileged exec
AAA-server of privilege clear level 3 exec mode command
privilege clear level 3 exec mode command crypto
level 3 for the privilege cmd mode configure command failover
clear level 3 privilege mode set the logging of command
privilege mode clear level 3 Configure arp command
clear level 3 privilege mode configure command crypto
clear level 3 privilege mode configure aaa-order server
context of prompt hostname
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Thanks in advance for any help.
Wojciech salvation,
Based on this info, I think that you can run in CSCtb53186, this bug has affected many versions before 8.3 and when fixed DEVs they were always be some details in waiting, and they created CSCtd36473 to these outstanding issues. CSCtd36473 is fixed on 8.3.1.1 intermediate version however is not fixed on 8.3.1 so I suggest you spend at least 8.3.2
Read this:
Interface: outside
Tag crypto map: outside_map, seq num: 1, local addr: 79.X.X.2list of access vpn extended permit ip 192.168.10.0 255.255.255.0 192.168.11.0 255.255.255.0
local ident (addr, mask, prot, port): (192.168.10.0/255.255.255.0/0/0)
Remote ident (addr, mask, prot, port): (192.168.11.0/255.255.255.0/0/0)
current_peer: 91.Y.Y.57#pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
#pkts decaps: 502, #pkts decrypt: 502, #pkts check: 502
compressed #pkts: 0, unzipped #pkts: 0
#pkts uncompressed: 0, comp #pkts failed: 0, #pkts Dang failed: 0
success #frag before: 0, failures before #frag: 0, #fragments created: 0
Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0
#send errors: 0, #recv errors: 0outgoing esp sas:
SPI: 0xDE50E6EA (3729843946)
transform: aes-256-esp esp-md5-hmac no compression
running parameters = {L2L, Tunnel}
slot: 0, id_conn: 425984, crypto-card: outside_map
calendar of his: service life remaining (KB/s) key: (4374000/28234)
Size IV: 16 bytes
support for replay detection: Y
Anti-replay bitmap:
0x00000000 0x00000001
VPN CTX = 0x015F913C
By peer IP = 192.168.11.0
Pointer = 0xD98CACD0
State = upwards
Flags = BA + ESP
ITS = 0X019235E7
SPI = 0xDE50E6EA
Group = 0
Pkts = 0
Pkts bad = 0
Incorrect SPI = 0
Parody = 0
Bad crypto = 0
Redial Pkt = 0
Call redial = 0
VPN = filterhits = 0, user_data is0x15f913c, cs_id = 0xd83ad0e8, reverse, flags = 0 x 0 = 0 protocol
IP/ID=192.168.10.0 SRC, mask is 255.255.255.0, port = 0
IP/ID=192.168.11.0 DST, mask is 255.255.255.0, port = 0, dscp = 0 x 0hits = 44437, user_data is0xce165c, cs_id = 0xd83ad0e8, reverse, flags = 0 x 0 = 0 protocol
IP/ID=192.168.10.0 SRC, mask is 255.255.255.0, port = 0
IP/ID=192.168.11.0 DST, mask is 255.255.255.0, port = 0, dscp = 0 x 0As you can see above we are a different context to encrypt the traffic (not used with the spi of the sh cry ipsec his)
If you do the same packet tracer, but this time with the details of the key words at the end probs you will get to see that we use 0xce165c.
Just looked at your configuration again and before you do the upgrade please correct this:
list of access vpn extended permit ip 192.168.10.0 255.255.255.0 192.168.11.0 255.255.255.0
extended vpn 192.168.11.0 ip access list allow 255.255.255.0 192.168.10.0 255.255.255.0
Just remove the second line:
no -access extended vpn ip 192.168.11.0 list allow 255.255.255.0 192.168.10.0 255.255.255.0
Also:
No outside_map interface card crypto outside
and then:
outside_map interface card crypto outside
See if that helps before perforrming upgrade,
Kind regards.
-
Hello
I installed oracle 10g. It works well, but after that it says "connection refused, unable to open a session" and I have password expiration date chked its null and I gave a date even then I face same problem. So I reinstall every day, but is there a solution to this.
coz I create my own picture space users and load some tables of soft working people. but I find connection problems. I saved the screenshots of db pswd / login I give evry time I load.
.. KCOracle 8.1.6 is released in 1999. I didn't know that you can still download.
I installed 11g (2007) on a Windows desktop several times recently, and 10g (2004) is quite similar to the installation process and roughly the same configuration. 8i was probably similar, but I don't really know.
"ORA-01034: ORACLE is not available ' means that the database is not running (or possibly SQL * more couldn't find) so you need confirm if it runs or not and from there. However this thread is about 10g connection problems. You should start a new thread for 8i startup problems. This forum is for questions of SQL and PL/SQL in any way - you could try {forum: id = 61} or {forum: id = 64}.
-
Hello
I hope that there is someone who can help me.
When I connect the iMac (el capitan 10.11.3), bought in February. 2016, with the admin account, there no problem.
When I go to the user & preferences of groups to make some changes to the same admin account, I try to unlock the admin account. I fill the same password but it keep nine of the 10 times saying the password is not correct. I tried to change my password but he repeats to me that the password is incorrect. I do not use my ID apple for this admin account password. I would like to open a session without trying 25 times or more...
Thank you for your attention,
Kind regards
Toos
First, please ensure that caps lock is not on. Note that on some models of laptops, the LED of the caps lock key may not work when you start up if FileVault is turned on. When shift caps lock is enabled, there will be an arrow icon in the text box where you enter the password. Build on this, not on the LED.
Another reason why the password can not be recognized, is that the keyboard (input source) in the login screen is not what you expect. You can select one of the available provisions by choosing in the menu flag in the upper right, if it is displayed, or even browse the by pressing the key combination command-space or command-option-space.
If the user account is associated with an Apple ID, and you know the password Apple ID, then maybeApple ID can be used to reset your password for the user account. In OS X 10.10 and later versions, this option also works with FileVault, but only if you have enabled when you turn on FileVault. It is not retroactive. If not, see below.
Note: If you have enabled FileVault, this procedure does not apply. Follow rather the instructions on this page, under the heading "If you forget your password."
Start in recovery mode. When OS X Utilities window, select
Utilities ▹ Terminal
in the menu bar at the top of the screen, not one of the items in the OS X Utilities window.
In the window that opens, type this:
resetp
Press the tab key. The partial order you entered will automatically end this:
resetpassword
Press return. Opens a window to reset the password. Close the Terminal window to get him out of the way.
Select the boot volume ("Macintosh HD", unless you have given it a different name) if not already selected. You won't be able to do this if FileVault is turned on.
Select your username in the menu option allows you to select the account if not already selected.
Follow the prompts to reset the password. It is safer to choose a password that includes only the characters a - z, A - Z and 0-9.
Select
▹ Restart
in the menu bar.
You should now be able to login with the new password, but will reset the keychain (empty). If you have forgotten the password for the keychain (which is normally the same as the password for the connection), there is no way to recover it.
Maybe you are looking for
-
Pinned tabs are not visible.
After I pin a tab in ff29, she disappears to the left of the row of tabs. I see a grey box blank where the pinned tabs were visible in ff28.
-
Why not Windows Media Player 11 does not recognize w4a files in the library list more.
I have Windows XP Pro (SP3) with Windows Media Player 11. I had a virus wipe my hard drive (everything has been updated) and after reinstalling and updating everything, it no longer recognizes the w4a files, but it automatically plays them the OMP 11
-
How can I get rid of the malware known as Windows of custom settings?
Here we have a computer that has picked up the malware known as Windows of the custom settings. I downloaded, installed and tried to run Spyware Doctor, SuperAntiSpyware and a few others. I can't launch the software, obviously this malware prevents w
-
Many images open in separate windows photo gallery windows.
I want to be able to open multiple images in windows separated from windows photo gallery. When I open a photo, it opens a window of photo gallery. But then I find another image and it opens in the same window and the previous photo has disappeared
-
I have the following machine: model m9600t, KX745AV-ABA product number. I am running Windows 7 without problem. I want to update now for Windows 8, but through a compatibility check, he said that the system will not support Secure Boot. As I understa