ASA5505 PROBLEM VPN

Similar Questions

• With tunnel VPN ASA5505 problem

  The business needs is for a VLAN again on site to go directly back to an internet service to site B.

  Site A and B are connected by a service of WES MB 100.

  A site is a site of campus with about 25 switches. Him become VLAN on the site is for the engineer access only, so they can access their companys remote access service. This VLAN must stay back so there is very little potential of a trade-off on the live network.

  The solution that I just put in place is to place an ASA5505 as the dhcp server for him VLAN become to Site A. All clients on that VLAN become get a 192.168.100.x address. The external interface on the ASA5505 to Site A is put on the live network to allow a site VPN tunnel to be put in place between the ASA5505 and the Internet - an another ASA5505 firewall

  The Site A ASA5505 was put in place with inside and outside interfaces with the same level of security. 192.168.100.x subnet is exempt from NAT. Traffic is configured to transmit via the interfaces with the same level of security and the tunnel of L2L is coming.

  But I can not all connectivity to the internet from any host on the 192.168.100.x VLAN.

  This is made more complex because the external interfaces on both of the ASA are the corporate network...

  The default route to the Site B ASA5505 is 87.xx.xx.1, the ISP router.

  The Site B ASA5505 connects directly to the ISP router.

  Site has ASA5505

  --------------------

  access-list no. - nat extended ip 192.168.100.0 allow 255.255.255.0 any

  Access access-list ON scope ip 192.168.100.0 allow 255.255.255.0 any

  NAT (inside) - access list 0 no - nat

  Access-Group No. - nat inside interface

  Route outside 0.0.0.0 0.0.0.0 10.0.99.254 1

  Crypto ipsec transform-set AES-256 aes-256-esp esp-sha-hmac

  vpn-traffic 10 crypto card matches the address OUT access

  card crypto vpn-traffic 10 peers set ##Site B IP address #.

  card crypto vpn-traffic 10 game of transformation-AES-256

  vpn-traffic outside crypto map interface

  tunnel-group ##Site B IP address # type ipsec-l2l

  tunnel-group ##Site B IP address # ipsec - attributes

  pre-shared-key *.

  Site B ASA5505

  -------------------

  permit same-security-traffic intra-interface

  access-list no. - nat extended ip 192.168.100.0 allow 255.255.255.240 all

  outside_access_in of access allowed any ip an extended list

  Global (inside) 1 interface

  NAT (inside) - access list 0 no - nat

  NAT (outside) 1 192.168.100.0 255.255.255.0

  Access-Group No. - nat inside interface

  Access-group outside_access_in in interface outside

  Crypto ipsec transform-set AES-256 aes-256-esp esp-sha-hmac

  Crypto ipsec transform-set esp-aes-256 set1, esp-sha-hmac

  card crypto vpn-traffic 10 correspondence address wootton hall

  card crypto vpn-traffic 10 peers set ##Site an IP #.

  crypto-vpn 10 transform-set set1 traffic map

  vpn-traffic outside crypto map interface

  I spent some time on it and really need some advice form experts out there!

  Can you help me to know where I have gone wrong?

  Dan

  There are some parts of the configuration that you have published to that surprise me, such as the assignment of the default route on the inside interface. But these things are not at the heart of your problem. I agree that the core of your problem is probably the sheep access list. If I understand your needs, what you need is 192.168.100.0 is not translated by going to meets B, and is translated by going to the Internet. But your translation says access list never 192.168.100.0 since your access list as another destination:

  access-list no. - nat extended ip 192.168.100.0 allow 255.255.255.0 any

  My suggestion is to rewrite this access list and change the destination of the 'all' to be addresses behind B (LAN to B).

  HTH

  Rick

• VPN-ASA5505 problem

  Hi all

  I inherited this VPN and get slowly upward. At least users can connect to it now!  I had a few problems. Users can connect to the VPN, but cannot ping or access shared files on the server (192.168.2.3), but the VPN users must be able to make full use of the network.

  I removed the NAT rule.

  #no nat (inside) 1 0.0.0.0 0.0.0.0)

  And after removing that, VPN users have been able to navigate and access to internal resources. However, users in the office now had no internet. I went and added the rule of return and returned internet.

  Believe it is related to the split tunneling, what can I do to activate full VPN access and still have internet at Headquarters?

  ASA Version 7.2 (4)

  !

  ciscoasa hostname

  domain default.domain.invalid

  activate mI3N1CPoxB4FJhZg encrypted password

  2KFQnbNIdI.2KYOU encrypted passwd

  names of

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.2.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  209.124.X.X 255.255.255.252 IP address

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  passive FTP mode

  Server DNS 192.168.2.3 Group

  DNS server-group DefaultDNS

  domain default.domain.invalid

  the Exchange25 object-group network

  access-list standard split allow 192.168.2.0 255.255.255.0

  access-list extended sheep permit ip 192.168.2.0 255.255.255.0 192.168.2.0 255.255.255.0

  access-list extended sheep permit ip 192.168.2.0 255.255.255.0 192.168.10.0 255.255.255.0

  out_in of access allowed any ip an extended list

  outside_access_in list extended access permit tcp any eq smtp host 192.168.2.3 eq smtp

  outside_access_in list extended access permit tcp any host 192.168.2.3 eq https

  outside_access_in list extended access permit tcp any host 192.168.2.3 eq www

  outside-access allowed extended access list tcp no matter what interface outside eq 7000

  outside-access allowed extended access list tcp no matter what interface outside eq 3389

  outside-access allowed extended access list tcp no matter what interface outside eq 587

  outside-access allowed extended access list tcp no matter what interface outside eq https

  LAN_nat0_outbound list of allowed ip extended access any 192.168.10.0 255.255.255.0

  pager lines 24

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  IP local pool vpnpool 192.168.2.31 - 192.168.2.60

  ICMP unreachable rate-limit 1 burst-size 1

  ICMP allow any inside

  ASDM image disk0: / asdm - 524.bin

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access LAN_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0

  public static tcp (indoor, outdoor) interface 192.168.2.3 smtp smtp netmask 255.255.255.255

  public static tcp (indoor, outdoor) interface 7000 192.168.2.80 7000 netmask 255.255.255.255

  public static interface 3389 192.168.2.3 (indoor, outdoor) tcp 3389 netmask 255.255.255.255

  public static interface 587 587 netmask 255.255.255.255 tcp (indoor, outdoor) 192.168.2.3

  public static tcp (indoor, outdoor) interface https 192.168.2.3 https netmask 255.255.255.255

  Access-group out_in in interface outside

  Route outside 0.0.0.0 0.0.0.0 209.124.192.45 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  Enable http server

  http 0.0.0.0 255.255.255.255 outside

  http 192.168.2.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto-map dynamic dynmap 10 game of transformation-ESP-3DES-SHA

  map mymap 65000-isakmp ipsec crypto dynamic dynmap

  mymap outside crypto map interface

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Crypto isakmp nat-traversal 20

  Telnet 0.0.0.0 0.0.0.0 inside

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  management-access inside

  dhcpd dns 192.168.2.3

  !

  attributes of Group Policy DfltGrpPolicy

  No banner

  WINS server no

  value of server DNS 192.168.2.3

  DHCP-network-scope no

  VPN-access-hour no

  VPN - 5 concurrent connections

  VPN-idle-timeout 30

  VPN-session-timeout no

  VPN-filter no

  Protocol-tunnel-VPN IPSec l2tp ipsec webvpn

  allow password-storage

  disable the IP-comp

  Re-xauth disable

  Group-lock no

  disable the PFS

  IPSec-udp disable

  IPSec-udp-port 10000

  Split-tunnel-policy tunnelall

  Split-tunnel-network-list no

  TMA.local value by default-field

  Split-dns no

  Disable dhcp Intercept 255.255.255.255

  disable secure authentication unit

  disable authentication of the user

  user-authentication-idle-timeout 10

  disable the IP-phone-bypass

  disable the leap-bypass

  disable the NEM

  Dungeon-client-config backup servers

  MSIE proxy server no

  MSIE-proxy method non - change

  Internet Explorer proxy except list - no

  Disable Internet Explorer-proxy local-bypass

  disable the NAC

  NAC-sq-period 300

  NAC-reval-period 36000

  NAC-by default-acl no

  address pools no

  enable Smartcard-Removal-disconnect

  the firewall client no

  rule of access-client-none

  WebVPN

  url-entry functions

  HTML-content-filter none

  Home page no

  4 Keep-alive-ignore

  gzip http-comp

  no filter

  list of URLS no

  value of customization DfltCustomization

  port - forward, no

  port-forward-name value access to applications

  SSO-Server no

  value of deny message connection succeeded, but because some criteria have not been met, or because of a specific group policy, you are not allowed to use the VPN features. Contact your administrator for more information

  SVC no

  SVC Dungeon-Installer installed

  SVC keepalive no

  generate a new key SVC time no

  method to generate a new key of SVC no

  client of dpd-interval SVC no

  dpd-interval SVC bridge no

  deflate compression of SVC

  internal TMAgroup group strategy

  attributes of Group Policy TMAgroup

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value split

  gene AzJFyGPWta7durW9 encrypted privilege 15 password username

  username admin privilege 15 encrypted password hLjunphNGLvrgsRP

  username TMAen encrypted password ojCI79mnpWOehEZC

  tunnel-group TMAgroup type ipsec-ra

  attributes global-tunnel-group TMAgroup

  address vpnpool pool

  Group Policy - by default-TMAgroup

  IPSec-attributes tunnel-group TMAgroup

  pre-shared-key *.

  !

  !

  context of prompt hostname

  Cryptochecksum:78c4838558d030ac964d2c331deed909

  : end

  Hello

  Please add the following to your configuration:

  nonat_inside ip access list allow any 192.168.2.0 255.255.255.0
  

  NAT (inside) 0-list of access nonat_inside
  

  You must keep the "nat (inside) 1 0.0.0.0 0.0.0.0 ' so that your users access to the Internet.

  "Nat (inside) 0 nonat_inside access-list" allows to bypass the above rule only for traffic destined to the VPN pool.

  In addition, it is to you if you want to use split tunneling or not.

  More information on tunneling split:

  ASA/PIX: Allow the tunneling split for the VPN Clients on the example of Configuration of ASA

  Let me know.

  Portu.

  Please note all useful posts

• Client VPN ASA5505 problem

  My ASA5505Plus to connect to the internet and a laptop, the laptop can access the internet.

  a VPN client connect to the ASA but cannot access internal or external IPs

  I see that the default gateway is wrong, but cannot find how to change it:

  ********************************

  The connection-specific DNS suffix. :

  ... Description: Cisco Systems VPN card

  Physical address.... : 00-05-9A-3C-78-00

  DHCP active...: No.

  ... The IP address: 192.168.200.5

  ... Subnet mask: 255.255.255.0.

  ... Default gateway. : 192.168.200.1.

  DNS servers...: 4.2.2.2.

  ************************************

  I hope that's why I can't access either the laptop (192.168.200.2), Telnet (192.168.200.4) or through the internet via the customer management. I don't know if that part is configured correctly

  configuration see attachment

  Ofir,

  Try the following

  IP local pool VPN_Pool 172.16.20.1 - 172.16.20.254 netmask 255.255.255.0

  inside_nat0_outbound 192.168.200.0 ip access list allow 255.255.255.0 172.16.20.0 255.255.255.0

  no access list inside_nat0_outbound extended permits all ip 192.168.200.4 255.255.255.252

  allow no extended access list inside_nat0_outbound 255.255.255.0 IP 192.168.200.0 192.168.200.0 255.255.255.0

  Split_T 192.168.200.0 ip access list allow 255.255.255.0 172.16.20.0 255.255.255.0

  tunnel-group test general attributes

  address pool VPN_Pool

  no address pool test

  test group policy attributes

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list Split_T

  Crypto isakmp nat-traversal 20

  management-access inside

  Concerning

• ASA5505 problem of asymmetric routing? (I think)

  Good evening everyone,

  I'm looking for suggestions for a solutoion I met today... I am installing a new router and firewall into an existing network. The router is an Edgewater VOIP router to a cable connection with static IP. The firewall is an ASA5505 (security more). There is a third-party router in the mixture (Cisco 1841) which has a PTP connection goes to another site. I'll try to verbally explain the architecture of the network:

  Unfortunately, the existing network was flattened on a 19 on which I'm not allowed to change so:

  VLAN 1 = data network (they used a large 19)

  VLAN 40 = voice (for VOIP phones)

  Edgewater Port 4 > UNTAG 1, tag 40 > ASA5505 Port 0

  Edgewater Port WAN > Cable Modem

  Edgewater DHCP Server for VLAN 40

  ASA5505 Port 0 > UNTAG 1, tag 40 > router Edgewater

  1 port ASA5505 > UNTAG 1, tag 40 > Cisco 2950 FE0/4 (set manually vlan the native 1 2950 to work)

  2 port ASA5505 > UNTAG 1, tag 40 > Cisco SG300 Gig1

  Voice of ASA5505 route 0.0.0.0 0.0.0.0 VLAN40_IP_OF_EDGEWATER

  ASA5505 data route 0.0.0.0 0.0.0; 0 VLAN1_IP_OF_EDGEWATER

  ASA5505 DHCPD for VLAN 1 (small subnet, the rest is ready for static with a gateway from the Cisco 1841 (infrastructure))

  Cisco 2950 4 > UNTAG 1, tag 40 > ASA5505 Port 1

  Cisco 2950 GIg1 > UNTAG 1, tag 40 > Cisco 2950 B

  DG of Cisco 2950 a = IP of Cisco 1841

  Cisco 2950 B Gig1 > UNTAG 1, tag 40 > Gig1 Cisco 2950 (rising MM fiber)

  Cisco 2950 B FE11 > UNTAG 1, tag 40 > Cisco 1841 FE0/0

  Cisco 2950B DG = IP of Cisco 1841

  Cisco 1841 FE0/0 0/0.1 dot1q native 0/0.40 dot1q 40 > FE11 Cisco 2950 B

  Road to Cisco 1841 ip 0.0.0.0 0.0.0.0 firewall VLAN 1 Interface IP (Changed to ip route ip VLAN40_NETWORK VLAN40_IP_OF_EDGEWATER and VLAN1_NETWORK VLAN1_IP_TO_ASA5505)

  Cisco also has internal IP routes through the private point of connection to another site...

  I'm replacing out of their existing connection is a sonicwall firewall and adding a few new POE switches for VOIP phones, VOIP router and an ASA5505. I can't play nice no matter what I tried. It seems that I am running into problems of asymmetric routing (ASA send me some)

  Deny TCP (no relation) on the VLAN 1 static and given dhcp VLAN40 DHCP handed the Edgewater works fine, I can browse on without any problem)...

  I'm not sure what the best approach is to do this. They need to keep the 1841 for now until a connection VPN of STS can be configured with the ASA5505 to their ASA5510 at the other site (months on the road by their budget). All of their PC is statically allocated and using their default gateway as the C1841.

  If you need output all configs I created so far or havy of suggestions on how to solve my problem, I'd love to hear about them. I tried everything short of re - structuring their entire network or deletion of my VOIP router that manages a large number of configurations for VOIP PBX phones.

  Thank you!

  Jon

  Apologies, but this is a very confusing description of how it is configured.  A diagram would probably help.

  If the new VoIP router's DHCP server for vlan 40 where are the customers compared to this?

  You have two lanes on the SAA pointing the VoIP router, what is the reasoning behind this?

  Why are you the ASA to the router VoIP trunking?

  The VoIP router can hand out DHCP addresses for a network, that it is not directly connected or is it why you extended vlan 40 completely out to the VoIP router?

  The router VoIP must give the vlan 40 IPs.

  I guess maybe it's to do with my lack of understanding as to exactly what does a VoIP router (as opposed to a normal router).

  So maybe you could clarify?

  Jon

  Jon

• Problem VPN ASA 5505 8.3 (1) a site

  Hello

  My problem is with VPN site-to-site. It's between ASA5505 8.3 (1) and Pix 501 6.3 (5). The tunnel is created between them and it's good, here you have the results to see the crypto ipsec's and isakmp his

  ciscoasa # sh crypto isakmp his

  ITS enabled: 1

  Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)

  Total SA IKE: 1

  1 peer IKE: 91.X.X.57

  Type: L2L role: initiator

  Generate a new key: no State: MM_ACTIVE

  ciscoasa # sh crypto ipsec his

  Interface: outside

  Tag crypto map: outside_map, seq num: 1, local addr: 79.X.X.2

  list of access vpn extended permit ip 192.168.10.0 255.255.255.0 192.168.11.0 255.255.255.0

  local ident (addr, mask, prot, port): (192.168.10.0/255.255.255.0/0/0)

  Remote ident (addr, mask, prot, port): (192.168.11.0/255.255.255.0/0/0)

  current_peer: 91.X.X.57

  #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0

  #pkts decaps: 3757, #pkts decrypt: 3757, #pkts check: 3757

  compressed #pkts: 0, unzipped #pkts: 0

  #pkts uncompressed: 0, comp #pkts failed: 0, #pkts Dang failed: 0

  success #frag before: 0, failures before #frag: 0, #fragments created: 0

  Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0

  #send errors: 0, #recv errors: 0

  local crypto endpt. : 79.X.X.2/0, remote Start crypto. : 91.X.X.57/0

  Path mtu 1500, fresh ipsec generals 74, media, mtu 1500

  current outbound SPI: F1C2FD46

  current inbound SPI: 1BCF8C49

  SAS of the esp on arrival:

  SPI: 0x1BCF8C49 (466586697)

  transform: aes-256-esp esp-md5-hmac no compression

  running parameters = {L2L, Tunnel}

  slot: 0, id_conn: 376832, crypto-card: outside_map

  calendar of his: service life remaining (KB/s) key: (4373665/20348)

  Size IV: 16 bytes

  support for replay detection: Y

  Anti-replay bitmap:

  0xFFFFFFFF to 0xFFFFFFFF

  outgoing esp sas:

  SPI: 0xF1C2FD46 (4056087878)

  transform: aes-256-esp esp-md5-hmac no compression

  running parameters = {L2L, Tunnel}

  slot: 0, id_conn: 376832, crypto-card: outside_map

  calendar of his: service life remaining (KB/s) key: (4374000/20348)

  Size IV: 16 bytes

  support for replay detection: Y

  Anti-replay bitmap:

  0x00000000 0x00000001

  But the problem is, as you can see in a show crypto ipsec sa, there is now traffic to a remote network of ASA

  #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0

  I have a single device on the remote network sends data to a sysloger on the local network and it works fine, all received messages but not other way to traffic.

  To make sure that I go see the Nat and packet - trace entry inside tcp 192.168.10.7 1024 192.168.11.250 80 and looks like SHEEP works very well and traffic is allowed, but still once anything gets into the tunnel of local network

  Results

  ciscoasa # sh nat

  Manual NAT policies (Section 1)

  1 (one) to (all) source static sheep sheep sheep destination static sheep

  translate_hits = 0, untranslate_hits = 38770

  2 (inside) for the service public static obj - the source (on the outside) TCP1433 TCP1433 79.X.X.5 192.168.10.7

  translate_hits = 0, untranslate_hits = 95

  3 (inside) to the source (external) static obj - 192.168.10.7 interface service zzz zzz

  translate_hits = 0, untranslate_hits = 19

  4 (inside) of the (whole) source static obj - 10.0.0.0 obj - 10.0.0.0 destination static obj - 192.168.2.0 obj - 192.168.2.0

  translate_hits = 17, untranslate_hits = 0

  5 (inside) of the (whole) source static obj - obj - static 192.168.10.0 192.168.10.0 obj - obj-destination 10.1.1.1 10.1.1.1

  translate_hits = 134, untranslate_hits = 0

  6 (inside) to the (whole) source static obj - 10.1.1.1 obj - 10.1.1.1 destination static obj - 192.168.10.0 obj - 192.168.10.0

  translate_hits = 0, untranslate_hits = 0

  7 (inside) of the (whole) source static obj - 192.168.0.0 obj - 192.168.0.0 destination static obj - 192.168.2.0 obj - 192.168.2.0

  translate_hits = 172, untranslate_hits = 53

  Auto NAT policies (Section 2)

  1 (inside) (outside) source static obj - 192.168.10.3 service TCP 3389 3389 79.X.X.5

  translate_hits = 12, untranslate_hits = 4823

  2 (inside) (outside) source static obj - 192.168.10.5 79.X.X.3 DNS

  translate_hits = 341869, untranslate_hits = 41531

  3 (inside) (outside) source static obj - 192.168.10.3 - 01 79.X.X.5 service TCP 444 444

  translate_hits = 0, untranslate_hits = 0

  4 (inside) to the source (external) static obj - 192.168.10.7 tcp 3389 3389 service interface

  translate_hits = 21, untranslate_hits = 751

  5 (inside) (outside) source static obj - 192.168.10.7 - 02 interface tcp 8080 https service

  translate_hits = 0, untranslate_hits = 100

  6 (inside) (outside) source static obj - 192.168.10.11 79.X.X.5 TCP smtp smtp service

  translate_hits = 2, untranslate_hits = 18838

  7 (inside) (outside) source static obj - 192.168.10.11 - 01 udp 443 443 service 79.X.X.5

  translate_hits = 0, untranslate_hits = 0

  8 (inside) (outside) source static obj - 192.168.10.11 - 02 79.X.X.5 tcp https https service

  translate_hits = 221, untranslate_hits = 9770

  9 (inside) (outside) source static obj - 192.168.10.11 - 03 79.X.X.5 tcp https https service

  translate_hits = 0, untranslate_hits = 0

  10 (inside) (outside) source static obj - 192.168.10.15 79.X.X.5 service tcp www 81

  translate_hits = 0, untranslate_hits = 34

  11 (inside) (outside) source static obj - 192.168.10.26 79.X.X.5 service TCP 8080 8080

  translate_hits = 9, untranslate_hits = 4407

  12 (inside) (outside) source static obj - 192.168.10.26 - 01 79.X.X.5 tcp 8080 www service

  translate_hits = 0, untranslate_hits = 578

  13 (inside) (outside) source static obj - 192.168.10.220 79.X.X.6 service TCP 3389 3389

  translate_hits = 0, untranslate_hits = 41

  14 (inside) (outside) source static obj - 192.168.10.220 - 1 79.X.X.6 tcp https https service

  translate_hits = 0, untranslate_hits = 3

  15 (inside) to the obj_any interface dynamic source (external)

  translate_hits = 410005, untranslate_hits = 144489

  16 (invited) to dynamic interface of the source (outside) obj_any-01

  translate_hits = 19712, untranslate_hits = 4490

  ciscoasa # packet - trace entry inside tcp 192.168.10.7 1024 192.168.11.250 80

  Phase: 1

  Type: UN - NAT

  Subtype: static

  Result: ALLOW

  Config:

  NAT (any, any) source static sheep sheep sheep destination static sheep

  Additional information:

  NAT divert on exit to the outside interface

  Untranslate 192.168.11.250/80 to 192.168.11.250/80

  Phase: 2

  Type: ACCESS-LIST

  Subtype: Journal

  Result: ALLOW

  Config:

  Access-group inside_out in interface inside

  access-list extended inside_out permit ip 192.168.10.0 255.255.255.0 192.168.11.0 255.255.255.0

  Additional information:

  Direct flow from returns search rule:

  ID = 0xd9886ae8, priority = 13, area = allowed, deny = false

  hits = 18503, user_data = 0xd6581290, cs_id = 0 x 0, use_real_addr, flags = 0 x 0 = 0 protocol

  IP/ID=192.168.10.0 SRC, mask is 255.255.255.0, port = 0

  IP/ID=192.168.11.0 DST, mask is 255.255.255.0, port = 0, dscp = 0 x 0

  input_ifc = output_ifc = any to inside,

  Phase: 3

  Type: IP-OPTIONS

  Subtype:

  Result: ALLOW

  Config:

  Additional information:

  Direct flow from returns search rule:

  ID = 0xd80c87c8, priority = 0, sector = inspect-ip-options, deny = true

  hits = 1047092, user_data = 0 x 0, cs_id = 0 x 0, reverse, flags = 0 x 0 = 0 protocol

  IP/ID=0.0.0.0 SRC, mask is 0.0.0.0, port = 0

  IP/ID=0.0.0.0 DST, mask is 0.0.0.0, port = 0, dscp = 0 x 0

  input_ifc = output_ifc = any to inside,

  Phase: 4

  Type: NAT

  Subtype:

  Result: ALLOW

  Config:

  NAT (any, any) source static sheep sheep sheep destination static sheep

  Additional information:

  Direct flow from returns search rule:

  ID = 0xd9859830, priority = 6, area = nat, deny = false

  hits = 2107, user_data = 0xd83a9b48, cs_id = 0 x 0, use_real_addr, flags = 0 x 0 = 0 protocol

  IP/ID=192.168.10.0 SRC, mask is 255.255.255.0, port = 0

  IP/ID=192.168.11.0 DST, mask is 255.255.255.0, port = 0, dscp = 0 x 0

  input_ifc = none, output_ifc = any

  Phase: 5

  Type: HOST-LIMIT

  Subtype:

  Result: ALLOW

  Config:

  Additional information:

  Direct flow from returns search rule:

  ID = 0xd8114d98, priority = 0, domain = host-limit, deny = false

  hits = 674350, user_data = 0 x 0, cs_id = 0 x 0, flags = 0 x 0 = 0 protocol

  IP/ID=0.0.0.0 SRC, mask is 0.0.0.0, port = 0

  IP/ID=0.0.0.0 DST, mask is 0.0.0.0, port = 0, dscp = 0 x 0

  input_ifc = output_ifc = any to inside,

  Phase: 6

  Type: VPN

  Subtype: encrypt

  Result: ALLOW

  Config:

  Additional information:

  Direct flow from returns search rule:

  ID = 0xd83a9960, priority = 70, domain = encrypt, deny = false

  hits = 26732, user_data = 0xce165c, cs_id = 0xd83ad0e8, reverse, flags = 0 x 0 = 0 protocol

  IP/ID=192.168.10.0 SRC, mask is 255.255.255.0, port = 0

  IP/ID=192.168.11.0 DST, mask is 255.255.255.0, port = 0, dscp = 0 x 0

  input_ifc = none, output_ifc = external

  Phase: 7

  Type: NAT

  Subtype: rpf check

  Result: ALLOW

  Config:

  NAT (any, any) source static sheep sheep sheep destination static sheep

  Additional information:

  Direct flow from returns search rule:

  ID = 0xd98d1d70, priority = 6, area = nat-reversed, deny = false

  hits = 1419, user_data = 0xd83a9b48, cs_id = 0 x 0, use_real_addr, flags = 0 x 0 = 0 protocol

  IP/ID=192.168.10.0 SRC, mask is 255.255.255.0, port = 0

  IP/ID=192.168.11.0 DST, mask is 255.255.255.0, port = 0, dscp = 0 x 0

  input_ifc = none, output_ifc = any

  Phase: 8

  Type: VPN

  Subtype: ipsec-tunnel-flow

  Result: ALLOW

  Config:

  Additional information:

  Reverse flow from returns search rule:

  ID = 0xd9bda388, priority = 69 = ipsec-tunnel-flow area, deny = false

  hits = 486, user_data is 0x13492cc, cs_id = 0 x 0, reverse, flags = 0 x 0 = 0 protocol

  IP/ID=192.168.11.0 SRC, mask is 255.255.255.0, port = 0

  IP/ID=192.168.10.0 DST, mask is 255.255.255.0, port = 0, dscp = 0 x 0

  input_ifc = out, output_ifc = any

  Phase: 9

  Type: IP-OPTIONS

  Subtype:

  Result: ALLOW

  Config:

  Additional information:

  Reverse flow from returns search rule:

  ID = 0xd8192ab0, priority = 0, sector = inspect-ip-options, deny = true

  hits = 1169899, user_data = 0 x 0, cs_id = 0 x 0, reverse, flags = 0 x 0 = 0 protocol

  IP/ID=0.0.0.0 SRC, mask is 0.0.0.0, port = 0

  IP/ID=0.0.0.0 DST, mask is 0.0.0.0, port = 0, dscp = 0 x 0

  input_ifc = out, output_ifc = any

  Phase: 10

  Type: CREATING STREAMS

  Subtype:

  Result: ALLOW

  Config:

  Additional information:

  New workflow created with the 1293619 id, package sent to the next module

  Information module for forward flow...

  snp_fp_tracer_drop

  snp_fp_inspect_ip_options

  snp_fp_tcp_normalizer

  snp_fp_translate

  snp_fp_adjacency

  snp_fp_encrypt

  snp_fp_fragment

  snp_ifc_stat

  Information for reverse flow...

  snp_fp_tracer_drop

  snp_fp_inspect_ip_options

  snp_fp_ipsec_tunnel_flow

  snp_fp_translate

  snp_fp_tcp_normalizer

  snp_fp_adjacency

  snp_fp_fragment

  snp_ifc_stat

  Result:

  input interface: inside

  entry status: to the top

  entry-line-status: to the top

  output interface: outside

  the status of the output: to the top

  output-line-status: to the top

  Action: allow

  It is a complete config for ASA

  VPN

  Network local 192.168.10.0/24

  remote network 192.168.11.0/24

  Config

  :

  ASA Version 8.3 (1)

  !

  ciscoasa hostname

  domain.com domain name

  activate the password * encrypted

  passwd * encrypted

  names of

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.10.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP 79.X.X.2 255.255.255.248

  !

  interface Vlan12

  prior to interface Vlan1

  nameif comments

  security-level 80

  192.168.4.1 IP address 255.255.255.0

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  switchport access vlan 2

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  switchport access vlan 12

  !

  boot system Disk0: / asa831 - k8.bin

  passive FTP mode

  clock timezone GMT/UTC 0

  summer time clock GMT/BDT recurring last Sun Mar 01:00 last Sun Oct 02:00

  DNS domain-lookup outside

  DNS server-group DefaultDNS

  Server name 192.168.10.11

  domain.com domain name

  permit same-security-traffic inter-interface

  permit same-security-traffic intra-interface

  network object obj - 192.168.0.0

  Subnet 192.168.0.0 255.255.0.0

  network object obj - 192.168.2.0

  Subnet 192.168.2.0 255.255.255.128

  network object obj - 10.0.0.0

  subnet 10.0.0.0 255.0.0.0

  network object obj - 192.168.10.2

  host 192.168.10.2

  network object obj - 192.168.10.2 - 01

  host 192.168.10.2

  network object obj - 192.168.10.3

  host 192.168.10.3

  network object obj - 192.168.10.2 - 02

  host 192.168.10.2

  network object obj - 192.168.10.2 - 03

  host 192.168.10.2

  network object obj - 192.168.10.3 - 01

  Home 192.168.10.7

  network object obj - 192.168.10.5

  host 192.168.10.5

  newserver network object

  Home 192.168.10.7

  New SQL Server description

  network object obj - 192.168.10.7

  Home 192.168.10.7

  network of the A_79.X.X.6 object

  Home 79.X.X.6

  network of the PublicServer_NAT1 object

  Home 192.168.10.7

  zzz service object

  service source eq 1 65535 udp syslog destination range

  Syslog description

  purpose of the 79.X.X.5 network

  Home 79.X.X.5

  service of the TCP1433 object

  destination service tcp source eq 1433 1 65535 range

  Description TCP1433

  network object obj - 192.168.10.220

  Home 192.168.10.220

  network object obj - 192.168.10.220 - 1

  Home 192.168.10.220

  network object obj - 192.168.10.222

  Home 192.168.10.222

  network object obj - 192.168.10.2 - 04

  host 192.168.10.2

  network object obj - 192.168.10.7 - 02

  Home 192.168.10.7

  network object obj - 192.168.10.11

  Home 192.168.10.11

  network object obj - 192.168.10.11 - 01

  Home 192.168.10.11

  network object obj - 192.168.10.11 - 02

  Home 192.168.10.11

  network object obj - 192.168.10.11 - 03

  Home 192.168.10.11

  network object obj - 192.168.10.26

  Home 192.168.10.26

  network object obj - 192.168.10.26 - 01

  Home 192.168.10.26

  network object obj - 192.168.10.15

  Home 192.168.10.15

  network object obj - 192.168.10.11 - 04

  Home 192.168.10.11

  network object obj - 10.1.1.1

  host 10.1.1.1

  network object obj - 192.168.10.0

  192.168.10.0 subnet 255.255.255.0

  network object obj - 192.168.10.220 - 2

  Home 192.168.10.220

  network vpn-local object

  192.168.10.0 subnet 255.255.255.0

  object network vpn - ru

  subnet 192.168.11.0 255.255.255.0

  network obj_any object

  subnet 0.0.0.0 0.0.0.0

  network obj_any-01 object

  subnet 0.0.0.0 0.0.0.0

  object-group service syslog udp

  Service Description syslog group

  port-object eq syslog

  object-group service udp zzzz

  port-object eq syslog

  object-group service sss udp

  port-object eq syslog

  object-group network sheep

  object-network 192.168.10.0 255.255.255.0

  object-network 192.168.11.0 255.255.255.0

  object-network 192.168.3.0 255.255.255.0

  outside_all of access allowed any ip an extended list

  VPN_splitTunnelAcl list standard access allowed 192.168.0.0 255.255.0.0

  VPN_splitTunnelAcl list standard access allowed 10.0.0.0 255.0.0.0

  permit inside_nat0_outbound to access extended list ip 192.168.0.0 255.255.0.0 192.168.2.0 255.255.255.128

  inside_nat0_outbound to access ip 10.0.0.0 scope list allow 255.0.0.0 192.168.2.0 255.255.255.128

  access-list extended inside_out allow ip 192.168.11.0 255.255.255.0 192.168.10.0 255.255.255.0

  access-list extended inside_out permit ip 192.168.10.0 255.255.255.0 192.168.11.0 255.255.255.0

  scope of the inside_out to the list of permitted any one ip access

  inside_out to the access list extended 192.168.11.0 allowed any ip 255.255.255.0

  inside_out to the list of access permit tcp host 192.168.10.2 any eq smtp

  inside_out to the list of access permit tcp any any eq smtp

  access-list extended inside_out allow udp 192.168.10.0 255.255.255.0 host 10.1.1.1

  access-list extended inside_out permit udp host 10.1.1.1 192.168.10.0 255.255.255.0

  inside_out to the list of allowed extensive access icmp host 192.168.10.7 all

  inside_out to the list of allowed extensive access a whole icmp

  outside_zzz list of allowed ip extended access any external interface

  outside_zzz list extended access permit tcp host 87.X.X.73 host 79.X.X.5 eq 1433

  outside_zzz tcp extended access list refuse any host 79.X.X.5 eq 1433

  outside_zzz list extended access permitted tcp 207.126.144.0 255.255.240.0 eq 79.X.X.5 the smtp host

  outside_zzz tcp extended access list refuse any host 79.X.X.5 eq smtp

  outside_zzz access-list extended permit ip any host 79.X.X.5

  outside_zzz of access allowed any ip an extended list

  permit access list extended ip 192.168.10.0 outside_in 255.255.255.0 192.168.11.0 255.255.255.0

  access extensive list ip 192.168.11.0 outside_in allow 255.255.255.0 192.168.10.0 255.255.255.0

  access extensive list ip 192.168.11.0 outside_in allow 255.255.255.0 any

  outside_in list extended access permit tcp any host 192.168.10.15 eq 81

  outside_in list extended access permit ip any host 192.168.10.5

  access-list outside_in extended permit ip any host 79.X.X.4

  outside_in list extended access permit tcp host 82.X.X.166 host 192.168.10.7 eq 1433

  outside_in list extended access permit tcp host 84.X.X.30 host 192.168.10.7 eq 1433

  outside_in list extended access tcp refuse any host 192.168.10.7 eq 1433

  outside_in list extended access permit tcp any host 192.168.10.3 eq 444

  outside_in list extended access permitted tcp 207.126.144.0 255.255.240.0 host 192.168.10.11 eq 444

  outside_in list extended access permitted tcp 207.126.144.0 255.255.240.0 eq smtp host 192.168.10.11

  outside_in list extended access permitted tcp 207.126.144.0 255.255.240.0 host 192.168.10.2 eq smtp

  outside_in list extended access tcp refuse any host 192.168.10.11 eq smtp

  outside_in list extended access tcp refuse any host 192.168.10.2 eq smtp

  outside_in list extended access permit tcp any host 192.168.10.2 eq smtp

  outside_in list extended access permit udp any host 192.168.10.2 eq 443

  outside_in list extended access permit tcp any host 192.168.10.3 eq 3389

  outside_in list extended access permit tcp any host 192.168.10.2 eq 4125

  outside_in list extended access permit tcp any host 192.168.10.11 eq https

  outside_in list extended access permit tcp any host 192.168.10.2 eq https

  outside_in list extended access allowed esp all the host 91.X.X.57

  outside_in list extended access permit tcp any host 192.168.10.3 eq 1433

  access-list extended outside_in permit ip host 91.X.X.57 all

  access-list outside_in extended permit ip any host 79.X.X.5

  access-list outside_in extended permit ip any host 79.X.X.2

  outside_in list extended access permit tcp any host 79.X.X.6 eq 3389

  outside_in list extended access permit tcp any host 192.168.10.220 eq 3389

  outside_in list extended access permit tcp any host 79.X.X.5 eq 81

  access extensive list permits all ip a outside_in

  outside_in list extended access permit tcp host 91.X.X.178 host 192.168.10.7 eq 1433

  outside_in list extended access permit tcp host 87.X.X.73 host 192.168.10.7 eq 1433

  access-list extended qnap permit ip host 192.168.10.26 all

  access-list extended qnap permit ip any host 192.168.10.26

  phone_bypass list extended access allowed host 10.1.1.1 ip 192.168.10.0 255.255.255.0

  permit phone_bypass to access extended list ip 192.168.10.0 255.255.255.0 host 10.1.1.1

  phone_bypass list extended access allowed host 10.1.1.1 ip 192.168.2.0 255.255.255.0

  phone_bypass to access extended list ip 192.168.2.0 allow 255.255.255.0 host 10.1.1.1

  list of access vpn extended permit ip 192.168.10.0 255.255.255.0 192.168.11.0 255.255.255.0

  extended vpn 192.168.11.0 ip access list allow 255.255.255.0 192.168.10.0 255.255.255.0

  pager lines 24

  Enable logging

  exploitation forest-size of the buffer 1024000

  logging asdm-buffer-size 512

  logging buffered information

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  Comments of MTU 1500

  mask of local pool RemoteVPN 192.168.2.20 - 192.168.2.100 IP 255.255.255.0

  ICMP unreachable rate-limit 1 burst-size 1

  ICMP allow any inside

  ICMP allow all outside

  ASDM image disk0: / asdm - 631.bin

  enable ASDM history

  ARP timeout 14400

  NAT (any, any) source static sheep sheep sheep destination static sheep

  NAT source service (Interior, exterior) static obj - 192.168.10.7 79.X.X.5 TCP1433 TCP1433

  NAT (inside, outside) source static obj - 192.168.10.7 interface service zzz zzz

  NAT (inside, all) source static obj - 10.0.0.0 obj - 10.0.0.0 destination static obj - 192.168.2.0 obj - 192.168.2.0

  NAT (inside, all) source static obj - 192.168.10.0 obj - 192.168.10.0 destination static obj - 10.1.1.1 obj - 10.1.1.1

  NAT (inside, all) source static obj - 10.1.1.1 obj - 10.1.1.1 destination static obj - 192.168.10.0 obj - 192.168.10.0

  NAT (inside, all) source static obj - 192.168.0.0 obj - 192.168.0.0 destination static obj - 192.168.2.0 obj - 192.168.2.0

  !

  network object obj - 192.168.10.3

  NAT (inside, outside) static service tcp 3389 3389 79.X.X.5

  network object obj - 192.168.10.3 - 01

  NAT (inside, outside) static 79.X.X.5 tcp 444 444 service

  network object obj - 192.168.10.5

  NAT (inside, outside) public static dns 79.X.X.3

  network object obj - 192.168.10.7

  NAT (inside, outside) interface static service tcp 3389 3389

  network object obj - 192.168.10.220

  NAT (inside, outside) static service tcp 3389 3389 79.X.X.6

  network object obj - 192.168.10.220 - 1

  NAT (inside, outside) static 79.X.X.6 tcp https https service

  network object obj - 192.168.10.7 - 02

  NAT (inside, outside) interface static tcp 8080 https service

  network object obj - 192.168.10.11

  NAT (inside, outside) static 79.X.X.5 tcp smtp smtp service

  network object obj - 192.168.10.11 - 01

  NAT (inside, outside) udp 443 443 service 79.X.X.5 static

  network object obj - 192.168.10.11 - 02

  NAT (inside, outside) static 79.X.X.5 tcp https https service

  network object obj - 192.168.10.11 - 03

  NAT (inside, outside) static 79.X.X.5 tcp https https service

  network object obj - 192.168.10.26

  NAT (inside, outside) static 79.X.X.5 8080 8080 tcp service

  network object obj - 192.168.10.26 - 01

  NAT (inside, outside) static 79.X.X.5 tcp 8080 www service

  network object obj - 192.168.10.15

  NAT (inside, outside) static 79.X.X.5 tcp 81 www service

  network obj_any object

  NAT dynamic interface (indoor, outdoor)

  network obj_any-01 object

  NAT dynamic interface (guest, outdoor)

  Access-group inside_out in interface inside

  Access-group outside_in in external interface

  Route outside 0.0.0.0 0.0.0.0 79.X.X.1 1

  Route inside 10.0.0.0 255.0.0.0 192.168.10.4 1

  Route outside 10.1.1.1 255.255.255.255 192.168.10.4 1

  Route outside 192.168.11.0 255.255.255.0 79.X.X.2 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  dynamic-access-policy-registration DfltAccessPolicy

  RADIUS Protocol RADIUS AAA server

  reactivation impoverishment deadtime mode 1

  AAA-server RADIUS (inside) host 192.168.10.7

  key *.

  AAA authentication http LOCAL console

  the ssh LOCAL console AAA authentication

  LOCAL AAA authorization command

  http server enable 444

  http 0.0.0.0 0.0.0.0 inside

  http 0.0.0.0 0.0.0.0 outdoors

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  No vpn sysopt connection permit

  Service resetoutside

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-SHA 256 - aes - esp esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  Crypto-map dynamic outside_dyn_map pfs set 20 Group1

  Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA

  card crypto outside_map 1 match for vpn

  outside_map game 1 card crypto peer 91.X.X.57

  card crypto outside_map 1 set of transformation-ESP-AES-SHA

  outside_map map 1 lifetime of security association set seconds 28800 crypto

  card crypto outside_map 1 set security-association life kilobytes 4608000

  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

  outside_map interface card crypto outside

  crypto isakmp identity address

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  lifetime 28800

  Crypto isakmp nat-traversal 3600

  Telnet timeout 5

  SSH 0.0.0.0 0.0.0.0 inside

  SSH 0.0.0.0 0.0.0.0 outdoors

  SSH timeout 30

  Console timeout 0

  dhcpd dns 83.X.X.8 83.X.X.10

  dhcpd outside auto_config

  !

  dhcpd address 192.168.10.50 - 192.168.10.100 inside

  dhcpd dns 83.X.X.8 83.X.X.10 interface inside

  dhcpd lease interface 600 inside

  dhcpd interface to domain.com domain inside

  !

  Reviews of dhcpd address 192.168.4.50 - 192.168.4.100

  Dhcpd lease 600 interface comments

  Comments enable dhcpd

  !

  priority queue inside

  priority-queue outdoors

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  NTP 93.170.32.1 Server

  NTP 93.170.32.2 Server

  NTP 89.145.68.17 Server prefer

  WebVPN

  allow outside

  SVC image disk0:/anyconnect-win-2.4.1012-k9.pkg 1 regex 'Windows NT'

  SVC image disk0:/anyconnect-wince-ARMv4I-2.4.1012-k9.pkg 2 regex "Windows CE"

  enable SVC

  Auto-signon allow ip 192.168.0.0 255.255.0.0 basic auth-type

  internal l2l group policy

  attributes of the l2l group policy

  VPN-idle-timeout no

  Protocol-tunnel-VPN IPSec

  attributes of Group Policy DfltGrpPolicy

  value of server DNS 192.168.10.11

  Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list VPN_splitTunnelAcl

  value by default-field DOMAINl.local

  internal VPNv group strategy

  attributes of Group Policy VPNv

  value of server DNS 192.168.10.11

  Protocol-tunnel-VPN IPSec webvpn

  Split-tunnel-policy tunnelspecified

  value of Split-tunnel-network-list VPN_splitTunnelAcl

  field default value domain.com

  password username test * encrypted privilege 0

  username test attributes

  VPN-group-policy VPNv

  ID password cisco * encrypted

  roger password username * encrypted privilege 15

  attributes global-tunnel-group DefaultRAGroup

  address pool RemoteVPN

  attributes global-tunnel-group DefaultWEBVPNGroup

  address pool RemoteVPN

  Group-LOCAL RADIUS authentication server

  type tunnel-group VPNv remote access

  attributes global-tunnel-group VPNv

  address pool RemoteVPN

  Group-LOCAL RADIUS authentication server

  Group Policy - by default-VPNv

  IPSec-attributes tunnel-group VPNv

  pre-shared key *.

  tunnel-group testgroup type remote access

  tunnel-group testgroup General attributes

  management of the password password-expire-to-days 90

  tunnel-group 91.X.X.57 type ipsec-l2l

  IPSec-attributes tunnel-group 91.X.X.57

  pre-shared key *.

  !

  Global class-card class

  match default-inspection-traffic

  class-map qnap_band

  corresponds to the list of access qnap

  The class-card phone

  corresponds to the phone_bypass access list

  !

  !

  Policy-map global_policy

  Global category

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Policy-map qnap_access

  class qnap_band

  512000 64000 police entry

  512000 64000 release of police

  phone class

  set the advanced options of the tcp-State-bypass connection

  World-Policy policy-map

  Global category

  inspect the dns

  inspect the ftp

  inspect the pptp

  inspect the rtsp

  inspect the sip

  inspect the skinny

  Policy-map phone_bypass_policy

  phone class

  set the advanced options of the tcp-State-bypass connection

  !

  service-policy-international policy global

  service-policy qnap_access to the inside interface

  privilege level 3 mode exec cmd command perfmon

  privilege level 3 mode exec cmd ping command

  mode privileged exec command cmd level 3

  logging of the privilege level 3 mode exec cmd commands

  privilege level 3 exec command failover mode cmd

  privilege level 3 mode exec command packet cmd - draw

  privilege level 5 see fashion exec running-config command

  order of privilege show level 3 exec mode reload

  privilege level 3 exec mode control fashion show

  privilege see the level 3 exec firewall command mode

  privilege see the level 3 exec mode command ASP.

  processor mode privileged exec command to see the level 3

  privilege command shell see the level 3 exec mode

  privilege show level 3 exec command clock mode

  privilege exec mode level 3 dns-hosts command show

  privilege see the level 3 exec command access-list mode

  logging of orders privilege see the level 3 exec mode

  privilege, level 3 see the exec command mode vlan

  privilege show level 3 exec command ip mode

  privilege, level 3 see fashion exec command ipv6

  privilege, level 3 see the exec command failover mode

  privilege, level 3 see fashion exec command asdm

  exec mode privilege see the level 3 command arp

  command routing privilege see the level 3 exec mode

  privilege, level 3 see fashion exec command ospf

  privilege, level 3 see the exec command in aaa-server mode

  AAA mode privileged exec command to see the level 3

  privilege see the level 3 exec mode command crypto

  privilege, level 3 see fashion exec command vpn-sessiondb

  privilege level 3 exec mode command ssh show

  privilege, level 3 see fashion exec command dhcpd

  privilege, level 3 see the vpnclient command exec mode

  privilege, level 3 see fashion exec command vpn

  privilege level see the 3 blocks from exec mode command

  privilege, level 3 see fashion exec command wccp

  privilege, level 3 see the exec command in webvpn mode

  privilege control module see the level 3 exec mode

  privilege, level 3 see fashion exec command uauth

  privilege see the level 3 exec command compression mode

  level 3 for the show privilege mode configure the command interface

  level 3 for the show privilege mode set clock command

  level 3 for the show privilege mode configure the access-list command

  level 3 for the show privilege mode set up the registration of the order

  level 3 for the show privilege mode configure ip command

  level 3 for the show privilege mode configure command failover

  level 5 mode see the privilege set up command asdm

  level 3 for the show privilege mode configure arp command

  level 3 for the show privilege mode configure the command routing

  level 3 for the show privilege mode configure aaa-order server

  level mode 3 privilege see the command configure aaa

  level 3 for the show privilege mode configure command crypto

  level 3 for the show privilege mode configure ssh command

  level 3 for the show privilege mode configure command dhcpd

  level 5 mode see the privilege set privilege to command

  privilege level clear 3 mode exec command dns host

  logging of the privilege clear level 3 exec mode commands

  clear level 3 arp command mode privileged exec

  AAA-server of privilege clear level 3 exec mode command

  privilege clear level 3 exec mode command crypto

  level 3 for the privilege cmd mode configure command failover

  clear level 3 privilege mode set the logging of command

  privilege mode clear level 3 Configure arp command

  clear level 3 privilege mode configure command crypto

  clear level 3 privilege mode configure aaa-order server

  context of prompt hostname

  call-home

  Profile of CiscoTAC-1

  no active account

  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

  email address of destination [email protected] / * /

  destination-mode http transport

  Subscribe to alert-group diagnosis

  Subscribe to alert-group environment

  Subscribe to alert-group monthly periodic inventory

  monthly periodicals to subscribe to alert-group configuration

  daily periodic subscribe to alert-group telemetry

  Thanks in advance for any help.

  Wojciech salvation,

  Based on this info, I think that you can run in CSCtb53186, this bug has affected many versions before 8.3 and when fixed DEVs they were always be some details in waiting, and they created CSCtd36473 to these outstanding issues. CSCtd36473 is fixed on 8.3.1.1 intermediate version however is not fixed on 8.3.1 so I suggest you spend at least 8.3.2

  http://www.Cisco.com/Cisco/software/release.html?mdfid=279916854&flowid=4818&softwareid=280775065&release=8.3.2.Ed&rellifecycle=&relind=available&RelType=latest

  Read this:

  Interface: outside
  Tag crypto map: outside_map, seq num: 1, local addr: 79.X.X.2

  list of access vpn extended permit ip 192.168.10.0 255.255.255.0 192.168.11.0 255.255.255.0
  local ident (addr, mask, prot, port): (192.168.10.0/255.255.255.0/0/0)
  Remote ident (addr, mask, prot, port): (192.168.11.0/255.255.255.0/0/0)
  current_peer: 91.Y.Y.57

  #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0
  #pkts decaps: 502, #pkts decrypt: 502, #pkts check: 502
  compressed #pkts: 0, unzipped #pkts: 0
  #pkts uncompressed: 0, comp #pkts failed: 0, #pkts Dang failed: 0
  success #frag before: 0, failures before #frag: 0, #fragments created: 0
  Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0
  #send errors: 0, #recv errors: 0

  outgoing esp sas:

  SPI: 0xDE50E6EA (3729843946)

  transform: aes-256-esp esp-md5-hmac no compression

  running parameters = {L2L, Tunnel}

  slot: 0, id_conn: 425984, crypto-card: outside_map

  calendar of his: service life remaining (KB/s) key: (4374000/28234)

  Size IV: 16 bytes

  support for replay detection: Y

  Anti-replay bitmap:

  0x00000000 0x00000001

  VPN CTX = 0x015F913C

  By peer IP = 192.168.11.0
  Pointer = 0xD98CACD0
  State = upwards
  Flags = BA + ESP
  ITS = 0X019235E7
  SPI = 0xDE50E6EA
  Group = 0
  Pkts = 0
  Pkts bad = 0
  Incorrect SPI = 0
  Parody = 0
  Bad crypto = 0
  Redial Pkt = 0
  Call redial = 0
  VPN = filter

  hits = 0, user_data is0x15f913c, cs_id = 0xd83ad0e8, reverse, flags = 0 x 0 = 0 protocol
  IP/ID=192.168.10.0 SRC, mask is 255.255.255.0, port = 0
  IP/ID=192.168.11.0 DST, mask is 255.255.255.0, port = 0, dscp = 0 x 0

  hits = 44437, user_data is0xce165c, cs_id = 0xd83ad0e8, reverse, flags = 0 x 0 = 0 protocol
  IP/ID=192.168.10.0 SRC, mask is 255.255.255.0, port = 0
  IP/ID=192.168.11.0 DST, mask is 255.255.255.0, port = 0, dscp = 0 x 0

  As you can see above we are a different context to encrypt the traffic (not used with the spi of the sh cry ipsec his)

  If you do the same packet tracer, but this time with the details of the key words at the end probs you will get to see that we use 0xce165c.

  Just looked at your configuration again and before you do the upgrade please correct this:

  list of access vpn extended permit ip 192.168.10.0 255.255.255.0 192.168.11.0 255.255.255.0

  extended vpn 192.168.11.0 ip access list allow 255.255.255.0 192.168.10.0 255.255.255.0

  Just remove the second line:

  no -access extended vpn ip 192.168.11.0 list allow 255.255.255.0 192.168.10.0 255.255.255.0

  Also:

  No outside_map interface card crypto outside

  and then:

  outside_map interface card crypto outside

  See if that helps before perforrming upgrade,

  Kind regards.

• ASA5505 configure VPN primary and backup

  Dear experts,

  I would like to ask you a few question that now I didn't get any primary VPN and backup connection, how can we do on this is sue? (I mean that when the primary reduction, then backup connection is automatically)

  Could you advice me how can I do?

  Best regards

  Rechard_hk

  I guess we should have asked for a bit more information, it seems Marwan and I responded almost at the same time, and I'm sure he'll provide great info.

  I had more geared towards a scenario of a firewall failure fault tolerance or an ISP connection failed in an architecture Fw DOUBLE and DOUBLE tis.

  Assuming that you want to have redundant firewall design, is when you look into the firewall active / standby to provide firewall redundancy, but when it comes to connections continues with VPN when one firewall fails, this is with characteristic State in place.

  IM providing links for reference belloe to get an idea of fws active and reserve but ASA5505 is the only model who is a stateless person, it is not dynamic which means connections will have to re - perform when one firewall fails.

  Also to implement two firewalls for the implementation of the changeover you need security more license to enable the active feature and reserve. This license will also include the activation of support DMZ and power create a VLAN to 20, as well as support Double TIS.

  Example of active / standby

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00807dac5f.shtml

  Comparison of the ASA - Look into Ipsec more license and features.

  http://www.Cisco.com/en/us/products/ps6120/prod_models_comparison.html

  On the other hand you may have in the future a backup ISP link, not only do you have active failover / standby but you can also have a backup ISP must link primary link fails with ALS and follow-up of Staic routing.

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00806e880b.shtml

  Rgds

  Jorge

• ASA5505 - Maximum VPN Clients

  Hey all, any idea what the maximum number of VPN clients can connect to the ASA5505? It runs to the base image. Thank you, robert.

  The devices allowed for this platform:

  The maximum physical Interfaces: 8

  VLAN: 3, restricted DMZ

  Internal hosts: unlimited

  Failover: disabled

  VPN - A: enabled

  VPN-3DES-AES: enabled

  Peer VPN: 10

  WebVPN peers: 2

  Double ISP: disabled

  Junction ports VLAN: 0

  This platform includes a basic license.

  Yes, apparently your interpretation is correct. If you have a race box you lab this place and see what happens after the grid of th 11' client attempted to connect. Most likely the client wil see an error message.

  Please rate if useful.

  Concerning

  Farrukh

• Problem VPN gateway to gateway Cisco RV042 861

  Hello. I have problems with tunneling IPSec between a RV042 and a Cisco 861. I configured the IKE, turn the value, the access list and the Crypto map into the pit 861 the console and I configured the tunnel in the RV042 web application with the same IKE encryption, Diffie-Hellman group and authentication but the connection does not work. Advice or review for this type of connection? Thank you.

  Your default traffic will be natting to the outside world.

  You need without Nat Traffc of Source ip to Destination ip that you authorized in the VPN access list.

  Mean simply to deny source ip to destination ip in NAT ACL.

• Problem VPN l2l * No. Tx and Rx *.

  Hi friends,

  I have a problem with the version 2 of ASA´s 5540 and 5510 8.4.3 and 8.2.5 respectively, TOPOLOGY: LAN - ASA-* WAN *-ASA - LAN

  I have no side 5540 TX

  # sh vpn-sessiondb detail l2l

  Session type: LAN-to-LAN detailed

  Link: 189.213.94.5

  Index: 107 IP Addr: 189.213.94.5

  Protocol: IPsec IKEv1

  Encryption: hashing 3DES 3DES 3DES: SHA1 SHA1 SHA1

  TX Bytes: 0 bytes Rx: 19104

  Opening time: 09:30:57 CST Friday, February 8, 2013

  Duration: 0: 00: 14:00

  IKEv1 Tunnels: 1

  IPsec Tunnels: 2

  IKEv1:

  Tunnel ID: 107.1

  The UDP Src Port: 500 UDP Dst Port: 500

  IKE Neg Mode: Hand Auth Mode: preSharedKeys

  Encryption: 3DES hash: SHA1

  Generate a new key Int (T): 86400 seconds given to the key Left (T): 85549 seconds

  Group D/H: 2

  Name of the filter: OUTSIDE_cryptomap_1

  IPv6 filter:

  IPsec:

  Tunnel ID: 107,2

  Local addr: 10.10.0.0/255.255.255.0/0/0

  Remote addr: 192.168.2.0/255.255.255.0/0/0

  Encryption: 3DES hash: SHA1

  Encapsulation: Tunnel PFS Group: 2

  Generate a new key Int (T): 28800 seconds given to the key Left (T): 27949 seconds

  Generate a new key Int (D): 4608000 K-bytes given to the key Left (D): 4607991 K-bytes

  Idle Time Out: 0 Minutes idling left: 0 Minutes

  TX Bytes: 0 bytes Rx: 10200

  TX pkts: 0 Rx Pkts: 170

  IPsec:

  Tunnel ID: 107.3

  Local addr: 10.5.0.0/255.255.0.0/0/0

  Remote addr: 192.168.2.0/255.255.255.0/0/0

  Encryption: 3DES hash: SHA1

  Encapsulation: Tunnel PFS Group: 2

  Generate a new key Int (T): 28800 seconds given to the key Left (T): 27952 seconds

  Generate a new key Int (D): 4608000 K-bytes given to the key Left (D): 4607992 K-bytes

  Idle Time Out: 0 Minutes idling left: 0 Minutes

  TX Bytes: 0 bytes Rx: 8904

  TX pkts: 0 Rx Pkts: 84

  NAC:

  Reval Int (T): 0 seconds Left (T) Reval: 0 seconds

  SQ (T) Int: 0 seconds EoU Age (T): 852 seconds

  Chock on the left (T): 0 second Posture token:

  Redirect URL:

  And I have no side 5510 Rx

  # sh vpn-sessiondb detail l2l

  Session type: LAN-to-LAN detailed

  Link: 201.140.121.82

  Index: 695 IP Addr: 201.140.121.82

  Protocol: IPsec IKE

  Encryption: 3DES hash: SHA1

  TX Bytes: 22480 Rx bytes: 0

  Connect time: 17:33:15 CST Friday, February 8, 2013

  Duration: 0: 00: 16:00

  IKE tunnels: 1

  IPsec Tunnels: 2

  IKE:

  Tunnel ID: 695.1

  The UDP Src Port: 500 UDP Dst Port: 500

  IKE Neg Mode: Hand Auth Mode: preSharedKeys

  Encryption: 3DES hash: SHA1

  Generate a new key Int (T): 86400 seconds given to the key Left (T): 85407 seconds

  Group D/H: 2

  Name of the filter:

  IPsec:

  Tunnel ID: 695.2

  Local addr: 192.168.2.0/255.255.255.0/0/0

  Remote addr: 10.10.0.0/255.255.255.0/0/0

  Encryption: 3DES hash: SHA1

  Encapsulation: Tunnel PFS Group: 2

  Generate a new key Int (T): 28800 seconds given to the key Left (T): 27808 seconds

  Generate a new key Int (D): 4608000 K-bytes given to the key Left (D): 0 K-bytes

  Idle Time Out: 0 Minutes idling left: 0 Minutes

  TX Bytes: 11880 Rx bytes: 0

  TX pkts: Rx 198 Pkts: 0

  IPsec:

  Tunnel ID: 695.3

  Local addr: 192.168.2.0/255.255.255.0/0/0

  Remote addr: 10.5.0.0/255.255.0.0/0/0

  Encryption: 3DES hash: SHA1

  Encapsulation: Tunnel PFS Group: 2

  Generate a new key Int (T): 28800 seconds given to the key Left (T): 27811 seconds

  Generate a new key Int (D): 4608000 K-bytes given to the key Left (D): 0 K-bytes

  Idle Time Out: 0 Minutes idling left: 0 Minutes

  TX Bytes: 10600 Rx bytes: 0

  TX pkts: Rx 100 Pkts: 0

  NAC:

  Reval Int (T): 0 seconds Left (T) Reval: 0 seconds

  SQ (T) Int: 0 seconds EoU Age (T): 994 seconds

  Chock on the left (T): 0 second Posture token:

  Redirect URL:

  Hope you guys could help me understand the issue correctly.

  Thank you!

  Looks like your problem is that you have the route to 192.168.2.X pointing inwards on your 5540, when it should be pointing to your interface OUTSIDE, or just leave the default route take care of it.

  Remove the static method for 192.168.2.0 on the 5540:

  no road inside 192.168.2.0 255.255.255.0 10.10.0.1 1

  Then see if two-way communication that happens. Try: entry packet - trace inside the 10.10.0.1 icmp 1 1 192.168.2.1

  Once again. If all checked out, see if you have two-way communication through the VPN.

• Login problem VPN on PIX on the side of the inside of the n/w

  I am tring to connect to the vpn server (pix) outside my laptop within the network.

  I have routed ip vpn on pix515 and fine ping pix.but not able to ping of 3550 switch and computer laptop.

  How to get the vpn ip Switch? as I don't know the mask of the ip...

  I would also like to know... is their something extra that I need on pix or 3550?

  Hello!

  -What is the default gateway of your laptop?

  -You do any kind of NAT on the PIX? What is NAT PAT, static or normal?

  -Can you ping the inside of the PIX of the laptop?

  There could be several problems to solve here.

  (1) first of all, make sure that your laptop has access to the internet

  (2) If you want to ping him make sure internet you have an ACL on the PIX like the one below:

  i.e.

  Allow Access - list icmp an entire TEST

  TEST group access in the interface outside

  Also make sure you have no access list applied inside the PIX

  -Now, can you connect at all?

  -When you connect to? Another PIX? Router? Hub?

  If you pass by PAT make sure that you have this command on the PIX:

  "fixup protocol esp-ike.

  Please let me know if you can answer my questions, in this way, it would be easier to help you.

  Frank

• Problem VPN site-to-site

  Hi people,

  My company wishes to set up a VPN between our situation in Sarajevo and Mostar. We have a Cisco 871w in Sarajevo, it is in production, and the other will also be a router Cisco in Mostar.

  I'm not much configuration of Cisco routers so it was better for me to test the scenario in Packet Tracer, but it simply does not work.

  I added the tracer package file (see attachment), so it would be great if someone could take a look and tell me where is the problem.

  I'm not sure if the Cisco 871w supports this type of VPN or should I buy another router VPN?

  Thanks in advance,

  Damir

  Thank you...

  The problem is the NAT statement that you configured is not exempt crypto traffic. He gets PATed to the IP address that you configure on the NAT pool, and it does not match the ACL (ACL 101) crypto more, so this isn't the start of the VPN tunnel.

  Here's what you need to set up:

  Router Sarajevo:

  access-list 120 deny ip 192.168.10.0 0.0.0.255 192.168.20.0 0.0.0.255

  access-list 120 permit ip 192.168.10.0 0.0.0.255 any

  no ip inside the pool overld nat overload source list 7

  IP nat inside source list pool 120 overld overload

  Router Mostar:

  access-list 120 deny ip 192.168.20.0 0.0.0.255 192.168.10.0 0.0.0.255

  access-list 120 allow ip 192.168.20.0 0.0.0.255 any

  no ip inside the pool overld nat overload source list 7

  IP nat inside source list pool 120 overld overload

  I hope this helps.

• Any login problem VPN - ASA5510

  Hi all

  I'm simulate Anyconnect VPN connection in the laboratory. I have a problem when the Anyconnect VPN on ASA5510 configuration.

  I can have a successful connection anyconnect but I can't ping my firewall IPs Interface while I'm in the connection.

  ASA 5510

  Outside intellectual property: 192.168.1.1/24

  PC connected to the external Interface: 192.168.1.10/24

  Domestic IP:10.10.10.1/24

  PC connected inside the Interface: 10.10.10.100/24

  Pool: 10.20.20.11 - 10.20.20.50/24

  I have a VPN connection & the PC connected to the external Interface receives an IP address from the pool assigned (10.20.20.11 with the default gateway of 10.20.20.1). But I can't reach (ping/telent) to the ASA, even if I'm on the anyconnect VPN.

  I think that this is mainly because NAT/routing issue...

  Please find the attached file (with show execution & see the release of the version).

  Thanks in advance.

  Set "inside access management.

  Sent by Cisco Support technique iPad App

• ASA5505 - remove VPN connections

  Hey all, have a simple question.

  the following page indicates it can handle up to 10 connections vpn with a basic license. This means that we can configure only 10 credentials of the vpn user/pass? or, we can create, for example 50 accounts user/pass, but only 10 can remote in at the same time.

  http://www.Cisco.com/en/us/products/ps6120/prod_models_comparison.html

  Thanks for the help.

  -robert

  Robert,

  That's right... 10 ways to connections VPN is a vpn connections simultaneous maximum with base... license you can create as many users in the local database asa but only 10 RA VPN client sessions can be established, however, that this column includes also the VPN L2L, say if you have 1 site-to-site vpn and 9 RA vpn which has a total of 10 sessions VPN.

  Concerning

• Problem VPN site to Site with overlapping networks

  We currently have a PIX 515E firewall as a headboard with many tunnels of site-to-site configured for her with the enpoints of PIX 506. Our internal LAN addressing scheme is 172.18.0.0 255.255.0.0. Addresses of local network in two of the remote networks with congigured VPN site-to-site are 172.18.107.0 255.255.255.224 and 172.18.107.32 255.255.255.0. Remote network access to all services on our internal network very well. We have 20 other network segments configured the same way. The 172.18.107.32.0 network needs to communicate with the 172.18.107.0 network for the services of file on the other remote PIX. Since the station PIX will not allow traffic to leave the same interface it came we thought with him we would just set up a tunnel from site to site between the two remote LAN. After the configuration of the site to another remote firewalls do not appear to try to establish tunnels when sending valuable traffic. I turned on debug for ISAKMP and nothing is either sent or received on a remote Firewall with regard to these tunnels. It's almost like since we already have a tunnel set to our 172.18.0.0 internal LAN that the remote PIX will not build specifically to 172.18.107.0 tunnel. I am able to ping each remote peer with each other and hear protection rules, but nothing has ever been established.

  Is what we are trying to do possible? Sorry for the long post but the kind of a strange scenario. Thanks in advance for any help.

  In what order are the numbers of seqence card crypto for configuring vpn on pix distance units? It could be that you are trying to install is a lot and will be checked later as head of pix. If this is the case, then yes the 172.18/16 road prevail the 172.18.107/24. Try to rebuild the entrance card crypto with a lower number so that traffic to 172.18.107/24 comes first.

  I would like to know how it works.