AnyConnect macosx tls1.2 support

Similar Questions

• What version of AnyConnect is needed to support TLS v1.2

  I need support TLS v1.2 for PCI compliance. Can anyone confirm which version of AnyConnect is necessary? I can't say if it will support 3.x, or if I need to go to 4.x.

  Thank you

  -mike

  It requires AnyConnect 4.0.00048 or later with ASA 9.3 (2) or later version.

  Reference.

  Quote from the above referenced for AnyConnect 4.0 release notes:

  AnyConnect now supports TLS version 1.2 with the following additional cipher suites:

  • DHE-RSA-AES256-SHA256

  • DHE-RSA-AES128-SHA256

  • AES256-SHA256

  • AES128-SHA256

  Note	AnyConnect TLS 1.2 requires a secure gateway that also supports TLS 1.2. It is available in version 9.3 (2) of the ASA 5500 - X models.

• Cisco AnyConnect, Chrome OS Support

  Hello

  Do you know something about Cisco Anyconnect, Chrome o/s support? (Roadmap, etc.)

  Not the browser...

  Kind regards

  Hello

  As much as I know there no plan to support at this time.

  However that happens, if the system (chrome or Chrome) becomes popular we will work for you to make it work.

  It is linux based (AFAIR) and we already have the Anyconnect for Linux components, major problem could be integrated with GUI components.

  Been to any ship of flavor (OS Chrome or Chrome OS)?

  What I would say, it is to drop an email to your self, so they can report these applications to the business unit.

  Marcin

• Cisco AnyConnect do IPsec?

  Hi guys

  I have a Cisco ASA5520 with software Version 8.2 (5) in place, most my users are Mac users and I am currently looking into Cisco AnyConnect in comparison using the VPN client.

  I have a few questions

  (1) Cisco AnyConnect does he use IPSec or is it soley based SSL VPN?

  (2) the license information I have in my ASA below, I understand that I can get max 750 vpn peers am however I have reason to say that this does not apply to Cisco AnyConnect peers? and with Cisco AnyConnect, I can only have 2 peers? Also, what are the options for mobility anyconnect for?

  The devices allowed for this platform:

  The maximum physical Interfaces: unlimited

  VLAN maximum: 150

  Internal hosts: unlimited

  Failover: Active/active

  VPN - A: enabled

  VPN-3DES-AES: enabled

  Security contexts: 2

  GTP/GPRS: disabled

  SSL VPN peers: 2

  Total of the VPN peers: 750

  Sharing license: disabled

  AnyConnect for Mobile: disabled

  AnyConnect Cisco VPN phone: disabled

  AnyConnect Essentials: disabled

  Assessment of Advanced endpoint: disabled

  Proxy sessions for the UC phone: 2

  Total number of Sessions of Proxy UC: 2

  Botnet traffic filter: disabled

  (3) when you try to configure Cisco Anyconnect on the SAA by using ASDM, I noticed that I needed to download AnyConnect client images, but when I did this by downloading the .dmg for mac machines file I got the error message 'not an image valid of the SVC'. Is it because I'm under 8.2?

  Your help is highly appreciated

  Concerning

  Mohamed

  Hi Mohammad,.

  I'll answer your questions one by one:

  1 cisco Anyconnect version 3.0 and above all support SSL and IPSECv2 connection. If you want the user to connect using the Anyconnect client IPSECv2 then it will consume the SSL license and not the IPsec license however if you use IPSECv2 for connections such as vpn site to site then it will consume normal IPSec VPN license.

  2. one.  SSL VPN peers: this license gives you information about the number of users that can connect using SSL protocol for example using the Anyconnect and web portal customer also known as the clientless VPN based on. I see here there are only 2 licenses so at any given time only 2 users can connect successfully because 750 is the total number of licenses available for the VPN on the SAA, 698 only will be available for IPSec connections.

  b. Anyconnect for mobile: this license is required whenever a user connects from a Pocket like device: Iphone, Ipad, tablets etc.

  c. Anyconnect of Cisco VPN phone: Cisco IP phones have the ability to connect to an ASA remote using the SSL protocol and to enable this feature, you should have this license is activated on the SAA.

  d. Anyconnect essentials: Anyconnect there are two licenses, one > Anyconnect Premium and b > Anyconnect Essentials. AnyConnect essentials is less expensive as premium per report Anyconnect license. This license is for those who don't use webvpn or VPN without client. When the license is activated, the user can connect only to the Anyconnect VPN client.

  3. I don't know what image you use on the ASA. Please try the image named as anyconnect-macosx-i386 - 2.5.2010 - k9.pkg.

  To apply the changes using the command line, put this image on disk0: and then type this command on the CLI.

  Image disk0:/anyconnect-macosx-i386-2.5.2010-k9.pkg SVC

  Let me know if it helps.

  Thank you

  Vishnu Sharma

• Configuration AnyConnect helps Juniper SRX

  Hello and thanks for reading.

  This is a new Setup and I need support. I have not supported in TAC, but it has not proved effective.

  Internet - > Cisco ASA-> Juniper SRX-> extreme L3 SW-> APC

  What I've done so far is to install the latest images AnyConnect - anyconnect-macosx-i386 - 3.1.09013 - k9.pkg

  and running asa916-6 - k8.bin

  Please help with the Setup, with the IP space indicated, I have the last byte available for space public.184,.185, I drew the network in question. See photo.

  Untitled.PNG

  

  On the certificate, you can browse to your ASA outside interface and, using your browser ability inspection certificate, download the certificate to your local host. You can then import this certificate in the trusted root certificate authority (CA) store (or the equivalent on the non-windows hosts) and it will be not reliable for future connections. This may or may not be feasible by the technical knowledge of end users. For this reason and others, most enterprise deployments choose to use a problems of certificate by an established CA.

  For the issue of the domain, you must add your local domain if you / them to be added to the DNS suffix search list when a VPN connection is established.

• Cannot access internal network so AnyConnect SSL VPN, ASA 9.1 (6)

  Hello Cisco community support,

  I have a lab which consists of two virtual environments connected to a 3750-G switch that is connected to a 2901 router which is connected to an ASA 5512 - X which is connected to my ISP gateway. I configured SSL VPN using AnyConnect and can establish a VPN to the ASA from the outside but once connected, I can't access internal network resources or access the internet. My information network and ASA configuration is listed below. Thank you for any assistance you can offer.

  ISP network gateway: 10.1.10.0/24

  ASA to the router network: 10.1.40.0/30

  Pool DHCP VPN: 10.1.30.0/24

  Network of the range: 10.1.20.0/24

  Development network: 10.1.10.0/24

  : Saved
  :
  : Serial number: FCH18477CPT
  : Material: ASA5512, 4096 MB RAM, CPU Clarkdale 2793 MHz, 1 CPU (2 cores)
  :
  ASA 6,0000 Version 1
  !
  hostname ctcndasa01
  activate bcn1WtX5vuf3YzS3 encrypted password
  names of
  cnd-vpn-dhcp-pool 10.1.30.1 mask - 255.255.255.0 IP local pool 10.1.30.200
  !
  interface GigabitEthernet0/0
  nameif inside
  security-level 100
  IP 10.1.40.1 255.255.255.252
  !
  interface GigabitEthernet0/1
  nameif outside
  security-level 0
  address IP X.X.X.237 255.255.255.248
  !
  interface GigabitEthernet0/2
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/4
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/5
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  management only
  nameif management
  security-level 100
  IP 192.168.1.1 255.255.255.0
  !
  boot system Disk0: / asa916-1-smp - k8.bin
  boot system Disk0: / asa912-smp - k8.bin
  passive FTP mode
  permit same-security-traffic intra-interface
  network of the NETWORK_OBJ_10.1.30.0_24 object
  10.1.30.0 subnet 255.255.255.0
  network obj_any object
  network obj_10.1.40.0 object
  10.1.40.0 subnet 255.255.255.0
  network obj_10.1.30.0 object
  10.1.30.0 subnet 255.255.255.0
  outside_access_in list extended access permitted ip object NETWORK_OBJ_10.1.30.0_24 all
  FREE access-list extended ip 10.1.40.0 NAT allow 255.255.255.0 10.1.30.0 255.255.255.0
  access-list 101 extended allow any4 any4-answer icmp echo
  access-list standard split allow 10.1.40.0 255.255.255.0
  pager lines 24
  Enable logging
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  management of MTU 1500
  ICMP unreachable rate-limit 1 burst-size 1
  ICMP allow any inside
  ICMP allow all outside
  ASDM image disk0: / asdm - 743.bin
  don't allow no asdm history
  ARP timeout 14400
  no permit-nonconnected arp
  NAT (inside, outside) source obj_10.1.40.0 destination obj_10.1.40.0 static static obj_10.1.30.0 obj_10.1.30.0 non-proxy-arp-search to itinerary
  NAT (inside, outside) static source any any static destination NETWORK_OBJ_10.1.30.0_24 NETWORK_OBJ_10.1.30.0_24 non-proxy-arp-search to itinerary
  Access-group outside_access_in in interface outside
  !
  Router eigrp 1
  Network 10.1.10.0 255.255.255.0
  Network 10.1.20.0 255.255.255.0
  Network 10.1.30.0 255.255.255.0
  Network 10.1.40.0 255.255.255.252
  !
  Route outside 0.0.0.0 0.0.0.0 10.1.10.1 1
  Timeout xlate 03:00
  Pat-xlate timeout 0:00:30
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  without activating the user identity
  identity of the user by default-domain LOCAL
  Enable http server
  http 192.168.1.0 255.255.255.0 management
  http 192.168.1.0 255.255.255.0 inside
  http X.X.X.238 255.255.255.255 outside
  No snmp server location
  No snmp Server contact
  Crypto ipsec pmtu aging infinite - the security association
  Crypto ca trustpoint ASDM_Launcher_Access_TrustPoint_0
  registration auto
  full domain name no
  name of the object CN = 10.1.30.254, CN = ctcndasa01
  ASDM_LAUNCHER key pair
  Configure CRL
  trustpool crypto ca policy
  string encryption ca ASDM_Launcher_Access_TrustPoint_0 certificates
  certificate c902a155
  308201cd 30820136 a0030201 020204c 0d06092a 864886f7 0d 010105 9 02a 15530
  0500302b 31133011 06035504 03130 has 63 61736130 31311430 12060355 74636e64
  0403130 31302e31 2e33302e 32353430 1e170d31 35303731 32303530 3133315a b
  170d 3235 30373039 30353031 33315 has 30 2 b 311330 0403130a 11060355 6374636e
  64617361 30313114 30120603 55040313 0b31302e 312e3330 2e323534 30819f30
  0d06092a 864886f7 010101 05000381 8 d 0d 003081 89028181 00a47cfc 6b5f8b9e
  9b106ad6 857ec34c 01028f71 d35fb7b5 6a61ea33 569fefca 3791657f eeee91f2
  705ab2ea 09207c4f dfbbc18a 749b19ae d3ca8aa7 3370510b a5a96fd4 f9e06332
  4355 db1a4b88 475f96a1 318f7031 40668a4d afa44384 819d fa164c05 2e586ccc
  3ea59b78 5976f685 2abbdcf6 f3b448e5 30aa96a8 1ed4e178 0001300 020301 4 d d
  06092a 86 01010505 00038181 0093656f 639e138e 90b69e66 b50190fc 4886f70d
  42d9b4a8 11828da4 e0765d9c 52d84f8b 8e70747e e760de88 c43dc5eb 1808bd0f
  fd2230c1 53f68ea1 00f3e956 97eb313e 26cc49d7 25b927b5 43d8d3fa f212fcaf
  59eb8104 98e3a1d9 e05d3bcb 428cd7c6 61b530f5 fe193d15 ef8c7f08 37ad16f5
  d8966b50 917a88bb f4f30d82 6f8b58ba 61
  quit smoking
  Telnet timeout 5
  SSH stricthostkeycheck
  SSH timeout 5
  SSH group dh-Group1-sha1 key exchange
  Console timeout 0
  VPN-addr-assign local reuse / 360 time
  management of 192.168.1.2 - dhcpd address 192.168.1.254
  enable dhcpd management
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  Trust ASDM_Launcher_Access_TrustPoint_0 vpnlb-ip SSL-point
  SSL-trust outside ASDM_Launcher_Access_TrustPoint_0 point
  WebVPN
  allow outside
  AnyConnect image disk0:/anyconnect-linux-3.1.09013-k9.pkg 4
  AnyConnect image disk0:/anyconnect-macosx-i386-3.1.09013-k9.pkg 5
  AnyConnect image disk0:/anyconnect-win-3.1.09013-k9.pkg 6
  AnyConnect enable
  tunnel-group-list activate
  internal GroupPolicy_cnd-vpn group policy
  GroupPolicy_cnd-vpn group policy attributes
  WINS server no
  value of server DNS 8.8.8.8
  client ssl-VPN-tunnel-Protocol
  by default no
  xxxx GCOh1bma8K1tKZHa username encrypted password
  type tunnel-group cnd - vpn remote access
  tunnel-group global cnd-vpn-attributes
  address-cnd-vpn-dhcp-pool
  strategy-group-by default GroupPolicy_cnd-vpn
  tunnel-group cnd - vpn webvpn-attributes
  activation of the alias group cnd - vpn
  !
  ICMP-class class-map
  match default-inspection-traffic
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map icmp_policy
  icmp category
  inspect the icmp
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  inspect the icmp
  !
  global service-policy global_policy
  service-policy icmp_policy outside interface
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:261228832f3b57983bcc2b4ed5a8a9d0
  : end
  ASDM image disk0: / asdm - 743.bin
  don't allow no asdm history

  Can you confirm that this is correct, your diagram shows your IP address public on ASA as 30 while you have assinged on 'outside' interface like 29?

• IPSEC of AnyConnect-IKEv2 authentication failure

  I have configure Anyconnect webvpn using IPsec (IKEv2) to an ASA with version 8.4 (2). When I try to connect with Anyconnect Client mobility, I got an error message (see screenshot) authentication failed. I can't even invite him to put the name of user and password. Since him debugs, I get the following errors:

  % ASA-6-302015: built connection UDP incoming 354 for outside:x.x.x.x/52171 (x.x.x.x/52171) at identity:172.16.4.2/500 (172.16.4.2/500)

  % 5-ASA-750002: Local: 172.16.4.2:500 Remote:x.x.x.x:52171 Username:Unknown received a request IKE_INIT_SA

  % ASA-6-302015: built connection UDP incoming 355 for outside:x.x.x.x/52172 (x.x.x.x/52172) at identity:172.16.4.2/4500 (172.16.4.2/4500)

  % ASA-3-751006: failed local authentication: 172.16.4.2:4500 Remote:x.x.x.x:52172 Username:Unknown certificate.  Error: Impossible to retrieve the certificate chain

  % ASA-4-750003: Local: 172.16.4.2:4500 Remote:x.x.x.x:52172 Username:Unknown negotiation failed due to the ERROR: exchange Auth failed

  % ASA-6-302013: built of TCP connections incoming 356 for outside:x.x.x.x/52175 (x.x.x.x/52175) at identity:172.16.4.2/443 (172.16.4.2/443)

  % ASA-6-725001: from transfer SSL client outside:x.x.x.x/52175 for TLSv1 session.

  % ASA-725010 7: device supports the following 4 cipher (s).

  % ASA-7-725011: [1] encryption: RC4 - SHA

  % ASA-7-725011: [2] encryption: AES128-SHA

  % ASA-7-725011: [3] encryption: AES 256 - SHA

  % ASA-7-725011: [4] encryption: DES-CBC3-SHA

  % 7-ASA-725008: outside:x.x.x.x/52175 client SSL offers the following 18 cipher (s).

  % ASA-7-725011: encryption [1]: DHE-RSA-AES256-SHA

  % ASA-7-725011: [2] encryption: DHE-DSS-AES256-SHA

  % ASA-7-725011: [3] encryption: AES 256 - SHA

  % ASA-7-725011: [4] encryption: EDH-RSA-DES-CBC3-SHA

  % ASA-7-725011: [5] encryption: EDH-DSS-DES-CBC3-SHA

  % ASA-7-725011: [6] encryption: DES-CBC3-SHA

  % ASA-7-725011: [7] encryption: DHE-RSA-AES128-SHA

  % ASA-7-725011: [8] encryption: DHE-DSS-AES128-SHA

  % ASA-7-725011: [9] encryption: AES128-SHA

  % ASA-7-725011: [10] encryption: RC4 - SHA

  % ASA-7-725011: [11] encryption: RC4 - MD5

  % ASA-7-725011: [12] encryption: EDH-RSA-DES-CBC-SHA

  % ASA-7-725011: [13] encryption: EDH-DSS-DES-CBC-SHA

  % ASA-7-725011: [14] encryption: DES-CBC-SHA

  % ASA-7-725011: encryption [15]: EXP-EDH-RSA-DES-CBC-SHA

  % ASA-7-725011: encryption [16]: EXP-EDH-DSS-DES-CBC-SHA

  % ASA-7-725011: [17] encryption: EXP-DES-CBC-SHA

  % ASA-7-725011: [18] encryption: EXP-RC4-MD5

  % ASA-725012 7: device chooses cipher: RC4 - SHA for the SSL session with client outside:x.x.x.x/52175

  % ASA-6-725002: aircraft completed the SSL negotiation with customer outside:x.x.x.x/52175

  % ASA-6-725007: end of the SSL session with client outside:x.x.x.x/52175.

  % ASA-6-302014: disassembly of the TCP connection 356 for outside:x.x.x.x/52175 to identity:172.16.4.2/443 duration 0: 00:00 872 bytes TCP fins

  Here is my configuration:

  local pool VPNPOOL 172.17.1.1 - 172.17.1.40 255.255.255.0 IP mask

  object obj-vpnpool network

  172.17.1.0 subnet 255.255.255.0

  NAT (inside, outside) static source any any destination static obj-vpnpool obj-vpnpool

  standard SPLITUN-ACL access-list allowed 192.168.0.0 255.255.255.0

  standard SPLITUN-ACL access-list allowed 10.1.1.0 255.255.255.0

  IKEv2 crypto policy 1

  aes-256 encryption

  integrity sha

  Group 5 2 1

  FRP sha

  second life 86400

  Crypto ikev2 activate out of service the customer port 443

  Trustpoint crypto ikev2 remote access _SmartCallHome_ServerCA

  Crypto ipsec ikev2 ipsec-proposal TS1-IKEV2

  Protocol esp 3des, aes to aes-192, aes-256 encryption

  Esp integrity sha - 1, md5 Protocol

  crypto dynamic-map DYN-map 40 value ikev2 ipsec-proposal TS1-IKEV2

  card crypto ASA1VPN 65535 isakmp ipsec dynamic DYN-map

  ASA1VPN interface card crypto outside

  ISAKMP nat-traversal crypto

  WebVPN

  AnyConnect image disk0:/anyconnect-linux-3.0.5075-k9.pkg 1

  AnyConnect image disk0:/anyconnect-macosx-i386-3.0.5075-k9.pkg 2

  AnyConnect image disk0:/anyconnect-win-3.0.5075-k9.pkg 5

  AnyConnect profiles Main_IKEv2_client_profile disk0: / Main_IKEv2_client_profile.xml

  AnyConnect enable

  allow outside

  tunnel-group-list activate

  internal GroupPolicy_Main_IKEv2 group strategy

  attributes of Group Policy GroupPolicy_Main_IKEv2

  Ikev2 VPN-tunnel-Protocol

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value SPLITUN-ACL

  value of server DNS 192.168.0.245

  value of server WINS 192.168.0.245

  jiffix.local value by default-field

  WebVPN

  AnyConnect value Main_IKEv2_client_profile type user profiles

  AnyConnect Dungeon-Installer installed

  type tunnel-group RemoteAccessIKEv2 remote access

  attributes global-tunnel-group RemoteAccessIKEv2

  Group Policy - by default-GroupPolicy_Main_IKEv2

  address VPNPOOL pool

  tunnel-group RemoteAccessIKEv2 webvpn-attributes

  enable Main_IKEv2 group-alias

  username user password xxxxx

  attributes of user username

  VPN-group-policy GroupPolicy_Main_IKEv2

  management-access inside

  SSH 172.17.1.0 255.255.255.0 inside

  Main_IKEv2_client_profile. XML

  http://schemas.xmlsoap.org/encoding/">

  hostname - ASA (IPsec)

  y.y.y.y

  IPsec

  You have the trustpoint with configured '_SmartCallHome_ServerCA' certificate? The partial configuration above don't indicte something little script which is where authentication does not reach your output to the log above.

  The output from the output of 'show crypto ca server certificates' would be useful.

• Client AnyConnect on Macbook Air

  Hello

  For the client Anyconnect on the Macbook Air, IPSEC) 1 can be used?, 2) split tunneling is disabled?

  Hello

  For Mac:

  AnyConnect

  Activation of the IPsec IKEv2 connections

  OPERATING SYSTEM	AnyConnect 3.1 Predeploy the Package name
  Mac OS X	AnyConnect-macosx-i386 - k9.dmg

  Mac OS X

  Table 8 Mac OS X support modules and the new features in 3.1 AnyConnect

  AnyConnect Module 3.1	Feature	Mac OS X 10.6, 10.7, 10.8 x 86 (32-bit) or x 64 (64-bit)
  	Comments from customers	Yes
  VPN	Kernel	Yes
  	IPv6	Yes
  	Suite-B (IPsec only)	Yes
  Network Access Manager	Kernel	NO.
  	IPv6	NO.
  	Suite-B	NO.
  Posture & Hostscan	Kernel	Yes
  	IPv6	Yes
  	Keystroke logger	Yes x 86 (32-bit) only
  Web Security		Yes
  DART		Yes

  Cisco IPsec client

  The Cisco IPsec client only is not currently supported with MAC OSX 10.6, but the built-in MAC VPN client can be used. The current configuration of head IPsec used for current users of Cisco's VPN IPsec Client should work with this client.

  Split tunneling can be turned off (just choose tunnelall)

  ASA 8.x: allow the tunneling split for AnyConnect VPN Client on the example of Configuration of ASA

  Please check the following information:

  Deployment Client AnyConnect secure mobility

  Release notes for Cisco AnyConnect Secure Mobility, version 3.1 Client

  Thanx.

  Portu

  Please note any workstation that you be useful.

  
  

• Windows 10 anyconnect vpn client

  Can someone please explain to me how to download the windows client to vpn anyconnect 10 on my asa 5516 9.5 version and configure the asa for windows 10 clients? Any help would be greatly appreciated.

  Thank you

  Lake

  Hello Lakeram,

  It's the same process, you must download the AnyConnect that is officially supported by Windows 10, as you can see below:

  AnyConnect 3.1MR10 (3.1.10010) and later are compatible with Windows 10 official release. Technical assistance Center (TAC) will be available from 29/07/2015.

  Download package on the flash of the ASA and the move to the WebVPN as image for Windows, and then configure the Tunnel Group, group policy and the XML profile, please follow the guide below:

  - http://www.cisco.com/c/en/us/td/docs/security/vpn_client/anyconnect/anyc...

  - http://www.cisco.com/c/en/us/support/docs/security/anyconnect-secure-mob...

  Those two will help you to properly, configure the AnyConnect

  Keep me posted, please note and mark it as correct the useful message

  David Castro,

• Cannot access within LAN of Cisco Anyconnect

  I'm new to the firewall and try to get my Anyconnect test configuration to connect to addresses within my Local network. The Anyconnect client connects easily, I can get to addresses Internet and tracer package told me it falls to phase 6, svc-webvpn. Can someone post my config? I don't know I'm missing something pretty obvious. Config is pasted below:

  !

  interface Ethernet0/0

  Description< uplink="" to="" isp="">

  switchport access vlan 20

  !

  interface Ethernet0/1

  Description< inside="">

  switchport access vlan 10

  Speed 100

  full duplex

  !

  interface Ethernet0/2

  Description< home="" switch="">

  switchport access vlan 10

  !

  interface Ethernet0/3

  switchport access vlan 10

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  Shutdown

  !

  interface Ethernet0/6

  Shutdown

  !

  interface Ethernet0/7

  Shutdown

  !

  interface Vlan10

  nameif inside

  security-level 100

  IP 192.168.1.99 address 255.255.255.0

  !

  interface Vlan20

  nameif OUTSIDE

  security-level 0

  DHCP client dns update

  IP address dhcp setroute

  !

  Vlan30 interface

  No nameif

  no level of security

  no ip address

  !

  Banner motd

  Banner motd +... +

  Banner motd |

  Banner motd | Any unauthorized use or access prohibited * |

  Banner motd |

  Banner motd | The Officer allowed the exclusive use.

  Banner motd | You must have explicit permission to access or |

  Banner motd | configure this device. All activities performed.

  Banner motd | on this unit can be saved and violations of.

  Banner motd | This strategy may result in disciplinary action, and |

  Banner motd | may be reported to the police authorities. |

  Banner motd |

  Banner motd | There is no right to privacy on this device. |

  Banner motd |

  Banner motd +... +

  Banner motd

  boot system Disk0: / asa824-k8

  passive FTP mode

  clock timezone cst - 6

  clock to summer time recurring cdt

  permit same-security-traffic intra-interface

  ICMP-type of object-group DEFAULT_ICMP

  Description< default="" icmp="" types="" permit="">

  response to echo ICMP-object

  ICMP-unreachable object

  ICMP-object has exceeded the time

  object-group network obj and AnyConnect

  host of the object-Network 192.168.7.20

  host of the object-Network 192.168.7.21

  host of the object-Network 192.168.7.22

  host of the object-Network 192.168.7.23

  host of the object-Network 192.168.7.24

  host of the object-Network 192.168.7.25

  access-list 101 extended allow icmp a whole

  !

  Note access-list ACL_OUTSIDE < anyconnect="" permit=""> >

  ACL_OUTSIDE list extended access permitted tcp everything any https eq

  ACL_OUTSIDE list extended access permit icmp any any DEFAULT_ICMP object-group

  !

  VPN_NAT list extended access permit ip host 192.168.7.20 all

  VPN_NAT list extended access permit ip host 192.168.7.21 all

  VPN_NAT list extended access permit ip host 192.168.7.22 all

  VPN_NAT list extended access permit ip host 192.168.7.23 all

  VPN_NAT list extended access permit ip host 192.168.7.24 all

  VPN_NAT list extended access permit ip host 192.168.7.25 all

  access-list extended sheep allowed ip group object obj-AnyConnect 192.168.1.0 255.255.255.0

  pager lines 24

  Enable logging

  timestamp of the record

  logging buffered information

  logging trap information

  exploitation forest asdm errors

  MTU 1500 inside

  Outside 1500 MTU

  mask 192.168.7.20 - 192.168.7.25 255.255.255.0 IP local pool AnyconnectPool

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 645.bin

  don't allow no asdm history

  ARP timeout 14400

  Global (1 interface OUTSIDE)

  NAT (INSIDE) 1 192.168.1.0 255.255.255.0

  NAT (OUTSIDE) 1 access-list VPN_NAT

  Access-group ACL_OUTSIDE in interface OUTSIDE

  !

  router RIP

  network 192.168.1.0

  passive-interface OUTSIDE

  version 2

  !

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  dynamic-access-policy-registration DfltAccessPolicy

  AAA authentication http LOCAL console

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  http 192.168.2.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Sysopt connection tcpmss 1200

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4688000 association

  Crypto-map dynamic dynmap 20 the value transform-set ESP-3DES-SHA

  map outside_map 64553-isakmp ipsec crypto dynamic dynmap

  outside_map interface card crypto OUTSIDE

  !

  ISAKMP crypto identity hostname

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  VPN-addr-assign local reuse-delay 120

  SSH 192.168.1.0 255.255.255.0 inside

  SSH 192.168.2.0 255.255.255.0 inside

  SSH timeout 60

  Console timeout 0

  management-access INTERIOR

  DHCP-client broadcast-flag

  dhcpd x.x.x.x dns

  dhcpd rental 43200

  dhcpd ping_timeout 2000

  dhcpd auto_config OUTSIDE

  !

  dhcpd address 192.168.1.150 - 192.168.1.180 inside

  dhcpd allow inside

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  NTP 216.229.0.179 Server

  SSL encryption, 3des-sha1-aes128-sha1 aes256-sha1 sha1 rc4

  localtrust point of trust SSL outdoors

  WebVPN

  allow outside

  AnyConnect essentials

  SVC disk0:/anyconnect-win-4.2.01035-k9.pkg 1 image

  SVC disk0:/anyconnect-linux-64-4.2.01035-k9.pkg 2 image

  Picture disk0:/anyconnect-macosx-i386-4.2.01035-k9.pkg 3 SVC

  enable SVC

  tunnel-group-list activate

  attributes of Group Policy DfltGrpPolicy

  Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn

  internal Anyconnect group strategy

  attributes Anyconnect-group policy

  value x.x.x.x DNS server

  VPN-tunnel-Protocol svc

  the address value AnyconnectPool pools

  type tunnel-group remotevpn remote access

  tunnel-group Anyconnect type remote access

  tunnel-group Anyconnect General attributes

  strategy-group-by default Anyconnect

  tunnel-group Anyconnect webvpn-attributes

  enable MY_RA group-alias

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  context of prompt hostname

  Auto-update 30 3 1 survey period

  Update automatic timeout 1

  call-home

  Profile of CiscoTAC-1

  no active account

  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

  email address of destination [email protected] / * /

  destination-mode http transport

  Subscribe to alert-group diagnosis

  Subscribe to alert-group environment

  Subscribe to alert-group monthly periodic inventory

  monthly periodicals to subscribe to alert-group configuration

  daily periodic subscribe to alert-group telemetry

  Cryptochecksum:d41d8cd98f00b204e9800998ecf8427e

  : end

  Hello

  You are missing a NAT FREE for Anyconnect traffic would allow you to access inside the network.

  access-list allowed sheep ip 192.168.1.0 255.255.255.0 192.168.7.0 255.255.255.0

  NAT (inside) 0 access-list sheep

  Add these two lines in the config file and you should be able to access the network interior.

  Kind regards

  Aditya

  Please evaluate the useful messages and mark the correct answers.

• AnyConnect disables native IPv6 when it is connected.

  Hello

  I work in an environment with double stack.

  So I natively uses IPv6 (and incidentally v4) to connect to different resources/hosts.

  Whenever I use AnyConnect to connect to a remote site, all features of IPv6 local/native stops working.

  Gateways that I connect to with AnyConnect are not provides ipv6 connectivity or address.

  So to be clear, my question isn't everything get ipv6 to knit on anyconnect, or to be able to connect using the anyconnect via ipv6.

  It's just that whenever I connect somewhere via AnyConnect I lose ALL my IPv6 connectivity.

  I can't even ping my gateway via the link-local or global address.

  c:\>ping fe80::217:eff:fea0:89 c 1

  Ping fe80::217:eff:fea0:89 c 1 with 32 bytes of data:

  PING: transmit failed. General failure.

  PING: transmit failed. General failure.

  If I disconnect the AnyConnect client, it works very well.

  It is worth noting that when I connect with AnyConnect I'm a limited list of tunnel of splitting in return, not "any tunnel.

  All the information I have found relate to the AnyConnect to transport IPv6...

  Anyone who has a simular problem or can point me in the right direction to solve this problem?

  I use AnyConnect version 3.0.4235 on Windows 7 (64-bit)

  Hello

  According to my understanding of the issue, you are working on environment double stack. When you use AnyConnect to connect to a remote site an IPv6 connectivity local/native all stops working.

  And if you disconnect the client, everything starts to work. I researched and found the following: -.

  In a dual stack or a dual interface environment, the IPv6 traffic would also be sent through the IPv4 AnyConnect tunnel since this is the default behavior and its not fixed yet.
  
  Although we can provision IPv4 split tunneling, there is no capability to do IPv6 split tunneling on the ASA. So until IPv6 split tunneling rules are available via the ASA, the client will not support arbitrary leaking of IPv6 data outside of

  the tunnel. This is true even if ipv6 is not configured for anyconnect.

  So to sum up, the AnyConnect client does not support split-tunneling of the IPv6 traffic.  All IPv6 traffic must go over the AnyConnect tunnel (ie TunnelAll).  If you are not supporting IPv6 over the tunnel, you will not be able to access IPv6 resources when connected.  There is currently an enhancement request in place to support split-tunnel on IPv6 - bug ID CSCtb74535.  You can reference the details of this bug ID via our Bug Toolkit:

  http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCtb74535

  I hope it helps.

  Thank you

  Shilpa

• PC may have the connection, but why MAC cannot have Anyconnect VPN?

  Hi, we have MAC and PC users. Two users could reach inside the network through ASA and Anyconnect VPN. However, MAC users can not have connection (please see screenshot in attachment). The output of the show run webvpn command is below:

  Act(config-WebVPN) # sh run webvpn
  WebVPN
  allow outside
  allow inside
  CSD image disk0:/csd_3.5.841-k9.pkg
  AnyConnect image disk0:/anyconnect-win-3.1.04066-k9.pkg 1
  AnyConnect enable
  tunnel-group-list activate
  Auto-signon allow ip 0.0.0.0 0.0.0.0 auth-type all the

  The lack of configuration ""anyconnect image disk0: /anyconnect -macosx- i386 - 2.5.2014 - k9.pkg "all the time." We don't think that this is the reason why MAC users are unable to reach the inside of the network because we do not have this command for a long time. Any suggestions can give? Thank you.

  > The question is that the command for MAC was not there for long. Why is it could work when the order wasn't there?

  I don't know, but I remember that in versions, it was not necessary to have * all * images in flash. Perhaps this changed some time. , You upgrade your ASA recently before the problems began?

• MAC and PC can reach the same an ASA for Anyconnect VPN?

  Hi, we have MAC and PC users. We configure the Anyconnect VPN in an ASA. But two users need two image of sorts. We must therefore use the two commands:

  AnyConnect image disk0: / anyconnect -win- 3.1.04066 - k9.pkg

  AnyConnect image disk0: / anyconnect -macosx- i386 - 2.5.2014 - k9.pkg.

  This is what two commands cannot coexist in an ASA. How to solve the problem? I hope your suggestion. Thank you

  They can co-exist, but you must add different sequence numbers at the end of each command.

• Cisco ASA Anyconnect LAN access problem

  I have very simple network at home with the WAN IP address, ASA uses DHCP and gateway. plain of network of all no complications.

  X.X.X.X like a WAN

  192.168.1.0/24 as a LAN

  IP Pool 192.168.6.0/24 (VPN Pool)

  I am trying to configure AnyConnect (AC) so that I can connect remotely and get my resources on the LAN while out. I am to connect with AC and when you use split tunnel I'm browsing the web very well, but I have no access to the local network (without ICMP or TCP/UDP)

  Route looks good in customer AC

  unsecured network 0.0.0.0/0
  secure network 192.168.1.0/24

  What I'm missing for LAN access?, nat statement, list of access...?

  _____________________________

  Output of the command: "show run".

  : Saved
  :
  ASA Version 9.1 (5)
  !
  hostname asa01
  domain name asa

  names of
  192.168.6.2 mask - 192.168.6.100 local pool Pool VPN IP 255.255.255.0
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  switchport access vlan 5
  !
  interface Vlan1
  nameif inside
  security-level 100
  IP 192.168.1.1 255.255.255.0
  !
  interface Vlan2
  Outside description
  nameif outside
  security-level 0
  IP address XXXX
  !
  interface Vlan5
  nameif dmz
  security-level 50
  IP 192.168.100.1 address 255.255.255.0
  !
  boot system Disk0: / asa915 - k8.bin
  passive FTP mode
  clock timezone PST - 8
  clock summer-time recurring PDT
  DNS lookup field inside
  DNS domain-lookup outside
  DNS domain-lookup dmz
  DNS server-group DefaultDNS
  domain naisus.local
  permit same-security-traffic intra-interface
  network of the NETWORK_OBJ_192.168.1.0_24 object
  subnet 192.168.1.0 255.255.255.0
  network of the NETWORK_OBJ_192.168.6.0_25 object
  subnet 192.168.6.0 255.255.255.128
  object-group Protocol DM_INLINE_PROTOCOL_1
  icmp protocol object
  icmp6 protocol-object
  outside_access_in list extended access permit icmp any any idle state
  outside_access_in extended access list allow icmp6 all all idle state
  outside_access_in_1 list extended access allow DM_INLINE_PROTOCOL_1 of object-group a
  list of access allowed standard LAN 192.168.1.0 255.255.255.0
  pager lines 24
  Enable logging
  asdm of logging of information
  host of logging inside 192.168.1.99
  forest-hostdown operating permits
  Within 1500 MTU
  Outside 1500 MTU
  MTU 1500 dmz
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 741.bin
  don't allow no asdm history
  ARP timeout 14400
  no permit-nonconnected arp
  NAT (inside, outside) static source NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.6.0_25 NETWORK_OBJ_192.168.6.0_25 non-proxy-arp-search of route static destination
  !
  NAT source auto after (indoor, outdoor) dynamic one interface
  Access-group outside_access_in_1 in interface outside
  Route outside 0.0.0.0 0.0.0.0 X > X > X >
  Timeout xlate 03:00
  Pat-xlate timeout 0:00:30
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  identity of the user by default-domain LOCAL
  Enable http server
  http 192.168.1.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Crypto ipsec ikev2 ipsec-proposal OF
  encryption protocol esp
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 proposal ipsec 3DES
  Esp 3des encryption protocol
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal AES
  Esp aes encryption protocol
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 ipsec-proposal AES192
  Protocol esp encryption aes-192
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec ikev2 AES256 ipsec-proposal
  Protocol esp encryption aes-256
  Esp integrity sha - 1, md5 Protocol
  Crypto ipsec pmtu aging infinite - the security association
  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
  outside_map interface card crypto outside
  Crypto ca trustpoint ASDM_Launcher_Access_TrustPoint_0
  registration auto
  full domain name no
  name of the object CN = asa01, CN = 192.168.1.1
  ASDM_LAUNCHER key pair
  Configure CRL
  trustpool crypto ca policy
  string encryption ca ASDM_Launcher_Access_TrustPoint_0 certificates
  certificate 8b541b55
  308201c 3 c 3082012 a0030201 0202048b 0d06092a 864886f7 0d 010105 541b 5530
  XXXX
  quit smoking
  IKEv2 crypto policy 1
  aes-256 encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 10
  aes-192 encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 20
  aes encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 30
  3des encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  IKEv2 crypto policy 40
  the Encryption
  integrity sha
  Group 2 of 5
  FRP sha
  second life 86400
  Crypto ikev2 access remote trustpoint ASDM_Launcher_Access_TrustPoint_0
  Telnet 192.168.1.0 255.255.255.0 inside
  Telnet timeout 5
  SSH stricthostkeycheck
  SSH 192.168.1.0 255.255.255.0 inside
  SSH timeout 5
  SSH group dh-Group1-sha1 key exchange
  Console timeout 0

  dhcpd outside auto_config
  !
  dhcpd address 192.168.1.100 - 192.168.1.199 inside
  dhcpd dns 8.8.8.8 75.75.75.75 interface inside
  dhcpd naisus.home area inside interface
  dhcpd allow inside
  !
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  NTP server 50.116.56.17 source outdoors
  NTP server 108.61.73.243 source outdoors
  NTP server 208.75.89.4 prefer external source
  SSL-trust outside ASDM_Launcher_Access_TrustPoint_0 point
  Trust ASDM_Launcher_Access_TrustPoint_0 inside the vpnlb-ip SSL-point
  SSL-trust ASDM_Launcher_Access_TrustPoint_0 inside point
  WebVPN
  allow outside
  AnyConnect image disk0:/anyconnect-win-3.1.07021-k9.pkg 1 regex 'Windows NT'
  AnyConnect image disk0:/anyconnect-macosx-i386-3.1.07021-k9.pkg 2 regex "Intel Mac OS X.
  AnyConnect image disk0:/anyconnect-linux-64-3.1.07021-k9.pkg 3 regex "Linux".
  AnyConnect enable
  tunnel-group-list activate
  attributes of Group Policy DfltGrpPolicy
  VPN - connections 30
  VPN-idle-timeout 5
  internal GroupPolicy_AC_Profile group strategy
  attributes of Group Policy GroupPolicy_AC_Profile
  WINS server no
  4.2.2.2 DNS server value
  client ssl-VPN-tunnel-Protocol
  Split-tunnel-policy tunnelspecified
  Split-tunnel-network-list value LAN
  naisus.local value by default-field
  XX XX encrypted privilege 15 password username
  name of user XX attributes
  WebVPN
  chip-tunnel tunnel-policy tunnelall
  type tunnel-group AC_Profile remote access
  attributes global-tunnel-group AC_Profile
  address pool VPN-pool
  Group Policy - by default-GroupPolicy_AC_Profile
  tunnel-group AC_Profile webvpn-attributes
  enable AC_Profile group-alias
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  !
  global service-policy global_policy
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:xxx
  : end

  I'm not positive that's causing the problem, but I noticed that you have defined incoherent poolside VPN as a 24 (in the command name and that name is associated with the tunnel group) and 25 (in the command object on the network that is also referenced in the statement of NAT exempting NAT to that object). True your pool assigns addresses from the lower half of the 24, but still...

  I try to simplify things by using a single object for something like that, which is used in several places. With the help of objects the way they are intended, and which allows to avoid any discrepancies.

• AnyConnect VPN to ASA packages

  Anyone know where I can get the packages for the Anyconnect VPN client (Windows, OSX, Linux) to install in my ASA firewall to download?

  I need to upgrade the client, but I don't see on the site of Cisco are direct downloads for operating systems, not packages for the ASAs

  e.g. anyconnect-victory - 2.5.2014 - k9.pkg

  Hello Colin Higgins,

  You can find the last AnyConnect 3.1.X versions of client in the following link.

  https://software.Cisco.com/download/release.html?mdfid=286281272&SOFTWAR...

  In the previous link, look for the following files:

  -anyconnect-macosx-i386 - 3.1.08009 - k9.pkg
  -anyconnect-linux - 3.1.08009 - k9.pkg
  -anyconnect-victory - 3.1.08009 - k9.pkg

  You can download this file to the ASA and the next connection attempt, the end user must be able to download this new version.

  http://www.Cisco.com/c/en/us/TD/docs/security/vpn_client/AnyConnect/ANYC...

  I hope this helps.