AnyConnect VPN to ASA packages

Similar Questions

• Would become Anyconnect essentials Premium AnyConnect vpn on asa

  Dear team,

  We have a pair of cisco ASA 5520 with version 8.2 (5) works well with active mode / standby. As the situation requires, we intend to change the SSL vpn to clientless SSL VPN (AnyConnect Premium) to anyconnect vpn with mobile clients (IOS & Android)

  Please specify below

  (1) I have read, we cannot have two Anyconnect Essentials & AnyConnect Premium on the same system time. We need to disable accordingly to our need-pl correct me?

  (2) what is the best way to have the device for end-user client deployment? pushing of ASA or install individually on the system? Can I have the best, I mean the latest version of windows, client MAC e.t.c I shud get?

  While pushing ASA LU that much memory cache will be used, since we have IPS (AIP - SSM) modules has also installed on ASA who shud method I adopt here?

  (3) what is the exact product for license Anyconnect Essentials & customer name mobile (IOS & Android) we get from cisco?

  (4) once I get the correct license how do I active in systems? should I remove the failover command and install the license in two devices separately?

  (5) Finally, I need to authenticate vpn anyconnect essentials with LDAP that is already configured for clientless SSL VPN(AnyConnect Premium). any suggestions here?

  Below the version Sh emitted by the devices, it seems essential Anyconnect is already active... Please correct me?

  Active Firewall
  ===============

  System image file is "disk0: / asa825 - k8.bin.
  The configuration file to the startup was "startup-config '.

  Material: ASA5520, 2048 MB RAM, Pentium 4 Celeron 2000 MHz processor
  Internal ATA Compact Flash, 256 MB
  BIOS Flash Firmware Hub @ 0xffe00000, 1024 KB

  Hardware encryption device: edge Cisco ASA - 55 x 0 Accelerator (revision 0 x 0)
  Start firmware: CN1000-MC-BOOT - 2.00
  SSL/IKE firmware: CNLite-MC-Smls-PLUS - 2.03
  Microcode IPSec:-CNlite-MC-IPSECm-HAND - 2.05

  0: Ext: GigabitEthernet0/0: the address is a493.4ca3.ce0a, irq 9
  1: Ext: GigabitEthernet0/1: the address is a493.4ca3.ce0b, irq 9
  2: Ext: GigabitEthernet0/2: the address is a493.4ca3.ce0c, irq 9
  3: Ext: GigabitEthernet0/3: the address is a493.4ca3.ce0d, irq 9
  4: Ext: Management0/0: the address is a493.4ca3.ce09, irq 11
  5: Int: internal-Data0/0: the address is 0000.0001.0002, irq 11
  6: Int: internal-Control0/0: the address is 0000.0001.0001, irq 5

  The devices allowed for this platform:
  The maximum physical Interfaces: unlimited
  VLAN maximum: 150
  Internal hosts: unlimited
  Failover: Active/active
  VPN - A: enabled
  VPN-3DES-AES: enabled
  Security contexts: 2
  GTP/GPRS: disabled
  SSL VPN peers: 2
  Total of the VPN peers: 750
  Sharing license: disabled
  AnyConnect for Mobile: disabled
  AnyConnect Cisco VPN phone: disabled
  AnyConnect Essentials: enabled
  Assessment of Advanced endpoint: disabled
  Proxy sessions for the UC phone: 2
  Total number of Sessions of Proxy UC: 2
  Botnet traffic filter: disabled

  This platform includes an ASA 5520 VPN Plus license.

  =====================================================

  Firewall standby
  ================

  Updated Saturday, May 20, 11 16:00 by manufacturers
  System image file is "disk0: / asa825 - k8.bin.
  The configuration file to the startup was "startup-config '.

  Material: ASA5520, 2048 MB RAM, Pentium 4 Celeron 2000 MHz processor
  Internal ATA Compact Flash, 256 MB
  BIOS Flash Firmware Hub @ 0xffe00000, 1024 KB

  Hardware encryption device: edge Cisco ASA - 55 x 0 Accelerator (revision 0 x 0)
  Start firmware: CN1000-MC-BOOT - 2.00
  SSL/IKE firmware: CNLite-MC-Smls-PLUS - 2.03
  Microcode IPSec:-CNlite-MC-IPSECm-HAND - 2.05

  0: Ext: GigabitEthernet0/0: the address is 6073.5cab.3fae, irq 9
  1: Ext: GigabitEthernet0/1: the address is 6073.5cab.3faf, irq 9
  2: Ext: GigabitEthernet0/2: the address is 6073.5cab.3fb0, irq 9
  3: Ext: GigabitEthernet0/3: the address is 6073.5cab.3fb1, irq 9
  4: Ext: Management0/0: the address is 6073.5cab.3fb2, irq 11
  5: Int: internal-Data0/0: the address is 0000.0001.0002, irq 11
  6: Int: internal-Control0/0: the address is 0000.0001.0001, irq 5

  The devices allowed for this platform:
  The maximum physical Interfaces: unlimited
  VLAN maximum: 150
  Internal hosts: unlimited
  Failover: Active/active
  VPN - A: enabled
  VPN-3DES-AES: enabled
  Security contexts: 2
  GTP/GPRS: disabled
  SSL VPN peers: 2
  Total of the VPN peers: 750
  Sharing license: disabled
  AnyConnect for Mobile: disabled
  AnyConnect Cisco VPN phone: disabled
  AnyConnect Essentials: enabled
  Assessment of Advanced endpoint: disabled
  Proxy sessions for the UC phone: 2
  Total number of Sessions of Proxy UC: 2
  Botnet traffic filter: disabled

  This platform includes an ASA 5520 VPN Plus license.

  Thank you

  1 correct. You can run one or the other, but not both.

  2 since you have the upgrade memory to 2 GB, you should be fine perform web deployment via the pkg file method.

  3. for a 5520, you need:

  L-ASA-AC-E-5520 =
  L-ASA-AC-M-5520

  .. .to the Essentials and Mobile licenses respectively.

  4. on ASA 8.2, you need licenses for both units. If you upgrade to 8.3 + (8.4 (7) recommend at least), you can share licenses between members of a pair of HA. If you choose not to upgrade, just apply the key of activation on the rescue unit, then on the unit activates. You don't need to move on and in the failover configuration. Failover of the rescue unit status will show as ineligible briefly while he holds the new license is not the case of the active unit. Which will be resolved after you have applied the same license on the main unit. (If you were on 8.3 + would not happen at all).

  5. simply create a new connection profile for customers of Essentials by using the same AAA server group.

• AnyConnect VPN on ASA behind Internet router

  I have script like below and that you need assistance please

  Switch 10.10.1.1/30---> (10.10.1.2/30 inside the Interface) of base ASA (10.10.2.2/30 outside interface)---> public INT router (30.30.30.30/30) (10.10.2.1/30 LAN).

  I have configured the VPN but it needs more setup in the router and the VPN should be the public ip address so outside users can access.

  Fix.

  --

  Please do not forget to select a correct answer and rate useful posts

• I can't ping the interface inside of asa or telnet, when I came across the anyconnect vpn

  Hey Cisco net guys pro

  When I connect via anyconnect VPN to ASA 9.x, OS, I cannot ping inside
  the interface of asa or telnet, but I could ping at the interface of the router address
  ASA, the same two subnet

  Telnet 0.0.0.0 0.0.0.0 inside

  ICMP allow any insid

  Hi Ibrahim.

  Try 'inside access management' and let us know how it rates.

  Kind regards
  Dinesh Moudgil

  PS Please rate helpful messages.

• ASA Anyconnect VPN do not work or download the VPN client

  I have a Cisco ASA 5505 that I try to configure anyconnect VPN and thought, I've changed my setup several times but trying to access my static public IP address of the external IP address to download the image, I am not able to. Also when I do a package tracer I see he has been ignored through the acl when the packets from side to the ASA via port 443, it drops because of the ACL. My DMZ so will he look like something trying to access the ASA via the VPN's going to port 443. Here is my config

  XXXX # sh run
  : Saved
  :
  ASA Version 8.4 (3)
  !
  hostname XXXX
  search for domain name
  activate pFTzVNrKdD9x5rhT encrypted password
  zPBAmb8krxlXh.CH encrypted passwd
  names of
  !
  interface Ethernet0/0
  Outside-interface description
  switchport access vlan 20
  !
  interface Ethernet0/1
  Uplink DMZ description
  switchport access vlan 30
  !
  interface Ethernet0/2
  switchport access vlan 10
  !
  interface Ethernet0/3
  switchport access vlan 10
  !
  interface Ethernet0/4
  Ganymede + ID description
  switchport access vlan 10
  switchport monitor Ethernet0/0
  !
  interface Ethernet0/5
  switchport access vlan 10
  !
  interface Ethernet0/6
  switchport access vlan 10
  !
  interface Ethernet0/7
  Description Wireless_AP_Loft
  switchport access vlan 10
  !
  interface Vlan10
  nameif inside
  security-level 100
  IP 192.168.10.1 255.255.255.0
  !
  interface Vlan20
  nameif outside
  security-level 0
  IP address x.x.x.249 255.255.255.248
  !
  Vlan30 interface
  no interface before Vlan10
  nameif dmz
  security-level 50
  IP 172.16.30.1 255.255.255.0
  !
  boot system Disk0: / asa843 - k8.bin
  passive FTP mode
  DNS lookup field inside
  DNS domain-lookup outside
  DNS domain-lookup dmz
  DNS server-group DefaultDNS
  Name-Server 8.8.8.8
  Server name 8.8.4.4
  search for domain name
  network obj_any1 object
  subnet 0.0.0.0 0.0.0.0
  network of the Webserver_DMZ object
  Home 172.16.30.8
  network of the Mailserver_DMZ object
  Home 172.16.30.7
  the object DMZ network
  172.16.30.0 subnet 255.255.255.0
  network of the FTPserver_DMZ object
  Home 172.16.30.9
  network of the Public-IP-subnet object
  subnet x.x.x.248 255.255.255.248
  network of the FTPserver object
  Home 172.16.30.8
  network of the object inside
  192.168.10.0 subnet 255.255.255.0
  network of the VPN_SSL object
  10.101.4.0 subnet 255.255.255.0
  outside_in list extended access permit tcp any newspaper object Mailserver_DMZ eq www
  outside_in list extended access permit tcp any newspaper EQ 587 Mailserver_DMZ object
  outside_in list extended access permit tcp any newspaper SMTP object Mailserver_DMZ eq
  outside_in list extended access permit tcp any newspaper of the Mailserver_DMZ eq pop3 object
  outside_in list extended access permit tcp any newspaper EQ 2525 Mailserver_DMZ object
  outside_in list extended access permit tcp any newspaper of the Mailserver_DMZ eq imap4 object
  outside_in list extended access permit tcp any newspaper EQ 465 Mailserver_DMZ object
  outside_in list extended access permit tcp any newspaper EQ 993 Mailserver_DMZ object
  outside_in list extended access permit tcp any newspaper EQ 995 object Mailserver_DMZ
  outside_in list extended access permit tcp any newspaper EQ 5901 Mailserver_DMZ object
  outside_in list extended access permit tcp any newspaper Mailserver_DMZ eq https object
  Note access list ACL for VPN Tunnel from Split vpn_SplitTunnel
  vpn_SplitTunnel list standard access allowed 192.168.10.0 255.255.255.0
  pager lines 24
  Enable logging
  timestamp of the record
  exploitation forest-size of the buffer to 8192
  logging trap warnings
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  MTU 1500 dmz
  local pool VPN_SSL 10.101.4.1 - 10.101.4.4 255.255.255.0 IP mask
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 647.bin
  don't allow no asdm history
  ARP timeout 14400
  NAT (inside, outside) static source inside inside static destination VPN_SSL VPN_SSL
  NAT (exterior, Interior) static source VPN_SSL VPN_SSL
  !
  network obj_any1 object
  NAT static interface (indoor, outdoor)
  network of the Webserver_DMZ object
  NAT (dmz, outside) static x.x.x.250
  network of the Mailserver_DMZ object
  NAT (dmz, outside) static x.x.x.. 251
  the object DMZ network
  NAT (dmz, outside) static interface
  Access-group outside_in in external interface
  Route outside 0.0.0.0 0.0.0.0 x.x.x.254 1
  Timeout xlate 03:00
  Pat-xlate timeout 0:00:30
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  AAA-server protocol Ganymede HNIC +.
  AAA-server host 192.168.10.2 HNIC (inside)
  Timeout 60
  key *.
  identity of the user by default-domain LOCAL
  Console HTTP authentication AAA HNIC
  AAA console HNIC ssh authentication
  Console AAA authentication telnet HNIC
  AAA authentication secure-http-client
  http 192.168.10.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ca trustpoint localtrust
  registration auto
  Configure CRL
  Crypto ca trustpoint VPN_Articulate2day
  registration auto
  name of the object CN = vpn.articulate2day.com
  sslvpnkey key pair
  Configure CRL
  Telnet 192.168.10.0 255.255.255.0 inside
  Telnet timeout 30
  SSH 192.168.10.0 255.255.255.0 inside
  SSH timeout 15
  SSH version 2
  Console timeout 0
  No vpn-addr-assign aaa

  DHCP-client update dns
  dhcpd dns 8.8.8.8 8.8.4.4
  dhcpd outside auto_config
  !
  dhcpd address 192.168.10.100 - 192.168.10.150 inside
  dhcpd allow inside
  !
  dhcpd address dmz 172.16.30.20 - 172.16.30.23
  dhcpd enable dmz
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  authenticate the NTP
  NTP server 192.168.10.2
  WebVPN
  allow outside
  AnyConnect image disk0:/anyconnect-linux-64-3.1.06079-k9.pkg 1
  AnyConnect enable
  tunnel-group-list activate
  internal VPN_SSL group policy
  VPN_SSL group policy attributes
  value of server DNS 8.8.8.8
  client ssl-VPN-tunnel-Protocol
  Split-tunnel-policy tunnelspecified
  value of Split-tunnel-network-list vpn_SplitTunnel
  the address value VPN_SSL pools
  WebVPN
  activate AnyConnect ssl dtls
  AnyConnect Dungeon-Installer installed
  AnyConnect ssl keepalive 15
  AnyConnect ssl deflate compression
  AnyConnect ask enable
  ronmitch50 spn1SehCw8TvCzu7 encrypted password username
  username ronmitch50 attributes
  type of remote access service
  type tunnel-group VPN_SSL_Clients remote access
  attributes global-tunnel-group VPN_SSL_Clients
  address VPN_SSL pool
  Group Policy - by default-VPN_SSL
  tunnel-group VPN_SSL_Clients webvpn-attributes
  enable VPNSSL_GNS3 group-alias
  type tunnel-group VPN_SSL remote access
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  inspect esmtp
  !
  global service-policy global_policy
  context of prompt hostname
  no remote anonymous reporting call
  call-home
  Profile of CiscoTAC-1
  no active account
  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
  email address of destination [email protected] / * /
  destination-mode http transport
  Subscribe to alert-group diagnosis
  Subscribe to alert-group environment
  Subscribe to alert-group monthly periodic inventory
  monthly periodicals to subscribe to alert-group configuration
  daily periodic subscribe to alert-group telemetry
  Cryptochecksum:d41d8cd98f00b204e9800998ecf8427e
  : end

  XXXX #.

  You do not have this configuration:

   object network DMZ nat (dmz,outside) static interface

  Try and take (or delete):

   object network DMZ nat (dmz,outside) dynamic interface

• MAC and PC can reach the same an ASA for Anyconnect VPN?

  Hi, we have MAC and PC users. We configure the Anyconnect VPN in an ASA. But two users need two image of sorts. We must therefore use the two commands:

  AnyConnect image disk0: / anyconnect -win- 3.1.04066 - k9.pkg

  AnyConnect image disk0: / anyconnect -macosx- i386 - 2.5.2014 - k9.pkg.

  This is what two commands cannot coexist in an ASA. How to solve the problem? I hope your suggestion. Thank you

  They can co-exist, but you must add different sequence numbers at the end of each command.

• Cisco ASA and AnyConnect VPN certificate error

  Hello

  I am trying to configure Cisco AnyConnect VPN and everything works, but I get this warning message when the connection is opened:

  Error.jpg

  

  I don't have public certificate in ASA. Is it possible to use the self-signed certificate and get rid of this warning message?

  Hello

  This is expected behavior on the SAA for an SSL connection. You can certainly use the certificate self-signed on the SAA and then apply it on the external interface.
  Once done, you will need to install this certificate on the clients and this will alleviate the popup error message.

  Here is a document that you can refer to create a self-signed certificate.
  https://supportforums.Cisco.com/document/44116/ASA-self-signed-certificate-WebVPN

  Kind regards
  Dinesh Moudgil

  PS Please note the useful messages.

• Select the timeout on ASA Cisco Anyconnect VPN

  Hello world

  I use the Cisco Anyconnect VPN client with the ASA 5540 firewall. I need allow a time-out on the VPN clients, so they log off after x hours of inactivity.

  Thank you to

  Best respect

  Hello

  To my understanding of the default timeout value is 30 minutes

  You should be able to change this setting in the "username" configurations (if you use LOCAL AAA on the SAA) or under the configurations of the 'group policy' .

  The command is

  VPN-idle-timeout

  Here is the link of the commands reference

  http://www.Cisco.com/c/en/us/TD/docs/security/ASA/ASA-command-reference/...

  -Jouni

• How Anyconnect VPN users will connect with cisco ASA, which uses the server (domain controller) Radius for authentication

  Hi team

  Hope you do well. !!!

  currently I am doing a project which consists in CISCO ASA-5545-X, RADIUS (domain controller) server for authentication. Here, I need to configure Anyconnect VPN and host checker in cisco asa.

  1 users will connect: user advanced browser on SSL VPN pop past username and password.

  2. (cisco ASA) authentication: VPN sends credentials to the RADIUS server.

  3 RADIUS server: authentication: receipt and SSL VPN (ASA) group.

  4 connectivity creation: If employee: PC so NAW verified compliance, no PC check Assign user to the appropriate role and give IP.

  This is my requirement, so someone please guide me how to set up step by step.

  1. how to set up the Radius Server?

  2. how to configure CISCO ASA?

  Thanks in advance.

  Hey Chick,

  Please consult the following page of installation as well as ASA Radius server. The ASA end there is frankly nothing much difference by doing this.

  http://www.4salesbyself.com/1configuring-RADIUS-authentication-for-webvp...

  Hope this helps

  Knockaert

• SSH for indoor or outdoor IP de ASA over anyconnect vpn

  Hello world

  I have ssl anyconnect vpn for my lab at home.

  When I connect via anyconnect SSL I am unable to ssh to ASA inside and outside IP is this default behavior?

  I have access to administration config inside configured on the SAA.

  VPN IP 10.10.10.10 pool

  SSH 10.10.10.0 255.255.255.0 outside

  Concerning

  Mahesh

  Try adding a line like:

  nat (outside,any) source static vpn_pool_ip vpn_pool_ip destination static inside inside no-proxy-arp

• ASA checks AnyConnect VPN computer name

  Hi all

  I have searched the Forum and documentation, but have not found a solution to my problem.  I'm guessing it happens sometimes, but maybe I'm looking for the wrong thing.  We AnyConnect deployed across our cell phones, but have trouble with employees who do get the software from other sources AnyConnect and install on personal computers.  We are an agency, although relatively small, but we have policies in place and I need to lock for users unable to connect to the VPN unless you're a book PC connected to our AD domain.  I found a possible solution is to use dynamic access within the ASA policies to check the Windows computer name.  So I set up LDAP and has created a policy to check an AAA attribute.  It lets me select "MemberOf", which I assume it is the Group of users, but I need to check the name of the computer on the client before allowing access.

  Step by step of what I did, does anyone know of a more logical or easier way to lock on what AnyConnect VPN client computers can be used?

  Or if I go about this common sense with dynamic access policies, anyone have any suggestions or knowledge of documentation that helps to configure things properly when you check the computer name LDAP attribute?

  Thank you!

  JD

  Hey Joe,

  You do not need LDAP to do this, what you need is CSD (Cisco Secure Desktop) combined with DAP.

  Once you enable SSC, edit your DAP strategy and instead of an IPN to attribute you to try, add an attribute of endpoint (on the right hand side).

  To verify the host name, select the type of the attribute "peripheral".

  Alternatively, you can also activate the sweep of host (under Contract) and let the CSD to check the presence of a file with a certain file name, or a registry entry or a process name. CSD passes the result of this verification to the PAD, so you can use it in a policy (attributes of endpoint of type process, registry and files).

  Another alternative is to use the CSD with a policy before opening session - that you cannot check the host name, but it does not have control over the IP, OS type, certificate as well as the presence of a process, the registry key, the file. In this case you need not to DAP.

  HTH

  Herbert

• AnyConnect VPN for Cisco ASA 5505 refused connections

  I'm trying to set up my Cisco 5505 with AnyConnect VPN client VPN access.  Here is the relevant information of my config:

  interface Vlan2
  
      mac-address xxxx.xxxx.xxxx
  
      nameif outside
  
      security-level 0
  
      ip address A.A.A.A 255.255.255.240
  
      !
  
      access-list outside_access_in extended permit tcp any host C.C.C.C eq pptp
  
      access-list outside_access_in extended permit tcp any host C.C.C.C eq https
  
      access-list outside_access_in extended permit tcp any host C.C.C.C eq ftp
  
      access-list outside_access_in extended permit tcp any host C.C.C.D eq https
  
      access-list outside_access_in extended permit tcp any host C.C.C.D eq ftp
  
      access-list outside_access_in extended permit tcp any host C.C.C.D eq www
  
      access-list outside_access_in extended permit tcp any host C.C.C.C eq smtp
  
      access-list outside_access_in extended permit icmp any any
  
      access-list outside_access_in extended permit tcp any host C.C.C.D eq ssh
  
      access-list outside_access_in extended permit tcp any host C.C.C.D eq 8080
  
      access-list outside_access_in extended permit gre any host C.C.C.C
  
      access-list outside_access_out extended permit ip any any
  
      access-list inside_access_in extended permit ip any any
  
      access-list inside_access_in extended permit ip any interface outside
  
      access-list inside_access_out extended permit ip any any
  access-group inside_access_in in interface inside
  
      access-group inside_access_out out interface inside
  
      access-group outside_access_in in interface outside
  
      access-group outside_access_out out interface outside
  webvpn
  
      enable inside
  
      enable outside
  
      svc image disk0:/anyconnect-win-2.4.1012-k9.pkg 1
  
      svc enable
  group-policy DfltGrpPolicy attributes
  
      dns-server value X.X.X.X
  
      vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
  
      split-tunnel-policy tunnelspecified
  
      split-tunnel-network-list value
  
      address-pools value palm
  
      webvpn
  
        svc rekey time 30
  
        svc rekey method ssl
  
        svc ask enable default webvpn
  policy-map global_policy
  
      class inspection_default
  
        inspect pptp
  
        inspect http
  
        inspect icmp
  
        inspect ftp
  
      !
  

  When I try to connect, I get this error in the real-time log viewer:

  TCP access denied by ACL from X.X.X.X/57356 to outside:A.A.A.A/443
  

  Here are the details of the license:

  Licensed features for this platform:
  
      Maximum Physical Interfaces  : 8
  
      VLANs                        : 3, DMZ Restricted
  
      Inside Hosts                 : Unlimited
  
      Failover                     : Disabled
  
      VPN-DES                      : Enabled
  
      VPN-3DES-AES                 : Enabled
  
      SSL VPN Peers                : 2
  
      Total VPN Peers              : 10
  
      Dual ISPs                    : Disabled
  
      VLAN Trunk Ports             : 0
  
      Shared License               : Disabled
  
      AnyConnect for Mobile        : Disabled
  
      AnyConnect for Linksys phone : Disabled
  
      AnyConnect Essentials        : Disabled
  
      Advanced Endpoint Assessment : Disabled
  
      UC Phone Proxy Sessions      : 2
  
      Total UC Proxy Sessions      : 2
  
      Botnet Traffic Filter        : Disabled
  This platform has a Base license.
  

  Can someone tell me what I am doing wrong or what access list I'm missing?

  I have two Cisco ASA 5510 firewall with a similar setup configuration and the AnyConnect SSL VPN works great.

  Hi Matt,

  You are probably landing on the tunnel-group by default - you will need to indicate which group to connect to the client. This can be done in different ways - I see that you already have a defined group aliases, but to be able to use that you must configure:

  WebVPN

  tunnel-group-list activate

  Alternatively, if you have only a single group, you can add 'group-url https://yourasa.yourcompany.com/ permit' to the webvpn attributes tunnel-group.

  HTH

  Herbert

• AnyConnect VPN is not access to the ASA

  Hello

  I have an ASA 5512 - x configured as a hub AnyConnect VPN, but when I connect I can not access the firewall... I can ping the address 10.4.11.2 but I can not connect... No idea what to do? It's the running configuration:

  : Saved

  :

  ASA 1.0000 Version 2

  !

  asa-oi hostname

  domain xx.xx.xx.xx

  activate 7Hb0WWuK1NRtRaEy encrypted password

  2KFQnbNIdI.2KYOU encrypted passwd

  names of

  1.1.1.1 DefaultGW-outside name description default gateway outside

  name 10.4.11.1 description DefaultGW - Default Gateway inside Inside

  !

  interface GigabitEthernet0/0

  nameif inside

  security-level 100

  IP 10.4.11.2 255.255.255.0

  !

  interface GigabitEthernet0/5

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/5.2000

  VLAN 2000

  nameif outside

  security-level 0

  IP 1.1.1.2 255.255.255.252

  !

  interface Management0/0

  Shutdown

  No nameif

  no level of security

  no ip address

  management only

  !

  boot system Disk0: / asa861-2-smp - k8.bin

  passive FTP mode

  clock timezone BRST-3

  clock summer-time recurring BRDT 2 Sun Oct 0:00 Sun Feb 3 0:00

  DNS lookup field inside

  DNS domain-lookup outside

  DNS server-group DefaultDNS

  1.1.1.1 server name

  1.1.1.2 server name

  domain xx.xx.xx.xx

  permit same-security-traffic inter-interface

  permit same-security-traffic intra-interface

  network of the PoolAnyConnect object

  subnet 10.6.4.0 255.255.252.0

  access extensive list permits all ip a outside_in

  list of access by standard tunnel allowed 10.0.0.0 255.0.0.0

  pager lines 24

  Enable logging

  timestamp of the record

  exploitation forest-size of the buffer 1048576

  logging buffered information

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  mask 10.6.4.1 - 10.6.7.254 255.255.252.0 IP local pool PoolAnyConnect

  ICMP unreachable rate-limit 1 burst-size 1

  ICMP allow any inside

  ICMP allow all outside

  ASDM image disk0: / asdm - 66114.bin

  enable ASDM history

  ARP timeout 14400

  NAT (inside, outside) static source any any static destination PoolAnyConnect PoolAnyConnect non-proxy-arp-search to itinerary

  NAT (exterior, Interior) static source PoolAnyConnect PoolAnyConnect non-proxy-arp-search to itinerary

  Access-group outside_in in external interface

  Route outside 0.0.0.0 0.0.0.0 DefaultGW-outdoor 1

  Route inside 10.0.0.0 255.0.0.0 DefaultGW-Inside 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  AAA-Server LDAP protocol ldap

  AAA-server host 3.3.3.3 LDAP (inside)

  Timeout 5

  LDAP-base-dn o = xx

  LDAP-scope subtree

  LDAP-naming-attribute sAMAccountName

  novell server type

  identity of the user by default-domain LOCAL

  the ssh LOCAL console AAA authentication

  AAA authentication enable LOCAL console

  AAA authentication http LOCAL console

  Enable http server

  http 0.0.0.0 0.0.0.0 inside

  http 2.2.2.2 255.255.255.240 outside

  Telnet timeout 5

  SSH 0.0.0.0 0.0.0.0 inside

  SSH 2.2.2.2 255.255.255.240 outside

  SSH timeout 10

  Console timeout 10

  management-access inside

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  SSL cipher aes128-sha1 aes256-3des-sha1 sha1

  WebVPN

  allow outside

  AnyConnect essentials

  AnyConnect image disk0:/anyconnect-win-3.1.03103-k9.pkg 1

  AnyConnect enable

  tunnel-group-list activate

  internal GrpPolicyAnyConnect group strategy

  attributes of Group Policy GrpPolicyAnyConnect

  value of server DNS 1.1.1.1 1.1.1.2

  VPN - 1000 simultaneous connections

  client ssl-VPN-tunnel-Protocol

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value in tunnel

  field default value xx.xx.xx.xx

  admin Dp4l7Cmqr7SMHl.l encrypted privilege 15 password username

  tunnel-group AnyConnect type remote access

  tunnel-group AnyConnect General attributes

  address pool PoolAnyConnect

  LDAP authentication group-server

  Group Policy - by default-GrpPolicyAnyConnect

  tunnel-group AnyConnect webvpn-attributes

  enable AnyConnect group-alias

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  inspect the ctiqbe

  inspect the http

  inspect the dcerpc

  inspect the dns

  inspect the icmp

  inspect the icmp error

  inspect the they

  inspect the amp-ipsec

  inspect the mgcp

  inspect the pptp

  inspect the snmp

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  Cryptochecksum:9399e42e238b5824eebaa115c93ad924

  : end

  BTW, I changed the NAT configuration many attempts the problem, this is the current...

  YPU need to allow your client VPN address pool (10.6.4.1 mask - 10.6.7.254 255.255.252.0) ssh and http from 'outside' access, which is where they come from. Add them to the:

  http 0.0.0.0 0.0.0.0 inside

  http 2.2.2.2 255.255.255.240 outside

  SSH 0.0.0.0 0.0.0.0 inside

  SSH 2.2.2.2 255.255.255.240 outside

• ASA 5510 Anyconnect licenses with Cisco Anyconnect VPN IP phone

  Hi, hoping someone can shed some light on what I'm just more confused over trying to get by. Not sure if this goes in the section IP Telehpony or here...

  We have an ASA 5510 with the base license. We need to install IP phones to home teleworkers, and I understand there are Cisco IP phones that have built-in VPN clients to enable a tunnel to the central private network. IT seems that you can't use Anyconnect VPN to do this, and I am trying to establish what upgrade licenses, we must apply to the ASA, as both Anyconnect licenses that you get for free on the SAA is not enough.

  This is the phone that we seek;

  http://www.Cisco.com/en/us/prod/collateral/voicesw/ps6788/phones/ps10499/ps11005/data_sheet_c78-603725.html

  I want to know is the Anyconnect Essentials license will work with these IP phones?

  When I do a version of the show,

  The devices allowed for this platform:

  The maximum physical Interfaces: unlimited

  VLAN maximum: 50

  Internal hosts: unlimited

  Failover: disabled

  VPN - A: enabled

  VPN-3DES-AES: enabled

  Security contexts: 0

  GTP/GPRS: disabled

  SSL VPN peers: 2

  The VPN peers total: 250

  Sharing license: disabled

  AnyConnect for Mobile: disabled

  AnyConnect for Linksys phone: disabled

  AnyConnect Essentials: disabled

  Assessment of Advanced endpoint: disabled

  Proxy sessions for the UC phone: 2

  Total number of Sessions of Proxy UC: 2

  Botnet traffic filter: disabled

  This platform includes a basic license.

  It shows "AnyConnect for Linksys phone: Disabled", it is the same for the Cisco IP phones? It is the kind of specific license, should I seek for Anyconnect on IP phones or will Essentials?

  Hi Leo,

  you will need 2 licenses: an Anyconnect Premium license and a permit «Anyconnect of Cisco VPN phone»

  ASA 8.2 and earlier license "for Cisco VPN Phone" has been named "for phone Linksys' it's the same.

  CFR. http://www.Cisco.com/en/us/docs/security/ASA/asa84/license/license_management/license.html#wp1487574

  HTH

  Herbert

• Phones AnyConnect VPN cannot connect to network ASA high-speed AT & T uverse

  Phones AnyConnect VPN are configured to connect to the ASA 5510 running 8.4 (4), and it uses the Active Directory credentials to connect. The connection is successful external ISP systems including Comcast and smaller independent service providers. However, when all of us at the AT & T uverse service take this phone 7965 even at home it networks fails to make any connection to the ASA at all. A capture of packets on the ASA shows no activity connection to the IP address of our uverse.

  What's more, is that we can successfully authenticate the VPN of the phone when using the local account credentials (e.g. username admin password * priv 15) that are entered on the SAA. AT & T said that they are not blocking the ports. It is the confusion that this works for users to access local connection, but not with A/D.

  So I guess the question is: what is the first handshake TCP/UDP composed when a Cisco IP phone links AnyConnect SSL to an ASA and negotiates the authentication of the number of A/D? For example, what are the port numbers used in this handshake?  I couldn't find all the diagrams illustrating the HRT and the RFC for DTLS do not seem to have the answer either.

  Thanks in advance.

  -Athonia

  Note: we have a TAC case open currently with subject ASA 5510 VPN Edition w / 250 annyconnect user - SSL VPN for phones. Configuration

  I too ran on this issue and here is a description of what I found.

  If you use automatic network detection first trys phone ping the TFTP server, he has learned from the DHCP server or manually set with the parameter of the alternate TFTP server.  If the TFTP server is accessible the VPN will not connect and will not allow the user to connect manually.

  ATT Uverse use DHCP option 150, the same option as Cisco UC uses to automatically set the TFTP servers, to locate the local home gateway so that the STB can join him.  For this reason, you should notice that when you have a VPN phone on the network and view network settings the IP address of the TFTP server is the IP address of your default gatewat (The ATT router).

  Because of the automatic detection of network works in ping the TFTP server that the phone will always think that it is connected to the local network.  The workaround is to manually set the TFTP server on the phone * to the IP address that the TFTP server would have been if she had leared it from the DHCP server on your corporate network.  The reason you should do this instead of just using a Bogon address, is that once the VPN is connected it tryes to register to the address that you specified.

  Please let me know if this solves your problem as it did in our case.

  * If you do not know how to set the TFTP replacement setting you must first select the "replacement" TFTP protocol and press on * #.  This will allow you to change the default no to Yes.  The below named parameter TFTP Server 1 will then allow you to manually specify the address.