Configuration AnyConnect helps Juniper SRX

Similar Questions

• Help to configure Anyconnect

  I'm trying to configure Anyconnect for the 1st time through the graphical interface, even if I'm comfortable with the command line if necessary.  I am familiar with IOS and PIX before 8.3 so this is my 1st time with newer versions. My equipment is in a lab at the moment environment, but will be put into production soon.  I get the following error when you try to establish an Anyconnect VPN connection with the local account on the ASA. Here is my config

  

  ASA 1.0000 Version 2

  !

  hostname TOR1PLXSD01

  activate sxZETAvnsVuPSnUc encrypted password

  FomDbcd6ujnk.spR encrypted passwd

  names of

  !

  interface GigabitEthernet0/0

  Description management

  Speed 1000

  full duplex

  nameif inside

  security-level 100

  IP 172.21.20.1 255.255.255.0 watch 172.21.20.2

  !

  interface GigabitEthernet0/1

  Speed 1000

  full duplex

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/1.20

  Data Plexxus description

  VLAN 20

  nameif data

  security-level 50

  IP 172.16.18.1 255.255.255.0 watch 172.16.18.2

  !

  interface GigabitEthernet0/1.25

  DMZ description

  VLAN 25

  nameif DMZ

  security-level 25

  no ip address

  !

  interface GigabitEthernet0/2

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/3

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/4

  nameif outside

  security-level 0

  IP address XXX1 255.255.255.224 x.x.x.2

  interface GigabitEthernet0/5

  STATE/LAN failover Interface Description

  !

  interface Management0/0

  nameif management

  security-level 100

  IP 192.168.1.1 255.255.255.0

  management only

  !

  boot system Disk0: / asa861-2-smp - k8.bin

  passive FTP mode

  DNS domain-lookup data

  DNS server-group DefaultDNS

  Server name 172.16.18.21

  Server name 172.16.18.22

  network of the OBJ_INSIDE object - HOSTS_172.21.20.0

  172.21.20.0 subnet 255.255.255.0

  network of the OBJ_DATA object - HOSTS_172.16.18.0

  172.16.18.0 subnet 255.255.255.0

  acl_outside list extended access permit icmp any one

  acl_data list extended access permit icmp any one

  acl_inside list extended access permit icmp any one

  acl_dmz list extended access permit icmp any one

  pager lines 24

  Enable logging

  Within 1500 MTU

  data of MTU 1500

  MTU 1500 DMZ

  Outside 1500 MTU

  management of MTU 1500

  IP local pool vpn_pool1 172.16.22.5 - 172.16.22.250 mask 255.255.255.0

  IP local pool vpn_pool2 172.16.23.5 - 172.16.23.250 mask 255.255.255.0

  failover

  primary failover lan unit

  LAN failover failover GigabitEthernet0/5 interface

  link failover failover GigabitEthernet0/5

  failover interface ip Failover 4.4.4.1 255.255.255.0 ensures 4.4.4.2

  ICMP unreachable rate-limit 1 burst-size 1

  ICMP allow any privileged

  ICMP allow all data

  ICMP allow all DMZ

  ICMP allow all outside

  ASDM image disk0: / asdm - 66114.bin

  don't allow no asdm history

  ARP timeout 14400

  !

  network of the OBJ_INSIDE object - HOSTS_172.21.20.0

  NAT (inside, outside) dynamic 68.71.198.102

  network of the OBJ_DATA object - HOSTS_172.16.18.0

  NAT (data, Outside) 68.71.198.102 Dynamics

  acl_inside access to the interface inside group

  Access-group acl_data in the interface data

  Access-group acl_dmz in DMZ interface

  Access-group acl_outside in interface outside

  Route outside 0.0.0.0 0.0.0.0 68.71.198.97 1

  Route of data 172.16.5.0 255.255.255.0 172.16.18.3 1

  Route data 172.16.10.0 255.255.255.0 172.16.18.3 1

  Route of data 172.16.13.0 255.255.255.0 172.16.18.3 1

  Route of data 172.16.14.0 255.255.255.0 172.16.18.3 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  identity of the user by default-domain LOCAL

  the ssh LOCAL console AAA authentication

  Enable http server

  http 172.21.20.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

  Telnet timeout 5

  SSH 172.21.20.0 255.255.255.0 inside

  SSH timeout 5

  Console timeout 0

  No vpn-addr-assign aaa

  No dhcp vpn-addr-assign

  management of 192.168.1.2 - dhcpd address 192.168.1.254

  enable dhcpd management

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  allow outside

  AnyConnect essentials

  AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1

  AnyConnect enable

  internal AnyConnectClientPolicy group strategy

  attributes of Group Policy AnyConnectClientPolicy

  WINS server no

  value of 172.16.18.21 DNS server 172.16.18.22

  client ssl-VPN-tunnel-Protocol ikev2

  plexxus.ca value by default-field

  the address value vpn_pool1 vpn_pool2 pools

  dmradmin 1ZwOzoVS5TWIvR0h encrypted password username

  type tunnel-group AnyConnectClientProfile remote access

  attributes global-tunnel-group AnyConnectClientProfile

  Group Policy - by default-AnyConnectClientPolicy

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  Cryptochecksum:659360d147ccf882ab6cbb6e170ca8d2

  : end

  TOR1PLXSD01

  ASA 1.0000 Version 2

  !

  hostname TOR1PLXSD01

  activate sxZETAvnsVuPSnUc encrypted password

  FomDbcd6ujnk.spR encrypted passwd

  names of

  !

  interface GigabitEthernet0/0

  Description management

  Speed 1000

  full duplex

  nameif inside

  security-level 100

  IP 172.21.20.1 255.255.255.0 watch 172.21.20.2

  !

  interface GigabitEthernet0/1

  Speed 1000

  full duplex

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/1.20

  Data Plexxus description

  VLAN 20

  nameif data

  security-level 50

  IP 172.16.18.1 255.255.255.0 watch 172.16.18.2

  !

  interface GigabitEthernet0/1.25

  DMZ description

  VLAN 25

  nameif DMZ

  security-level 25

  no ip address

  !

  interface GigabitEthernet0/2

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/3

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/4

  nameif outside

  security-level 0

  IP 68.71.198.100 255.255.255.224 watch 68.71.198.101

  !

  interface GigabitEthernet0/5

  STATE/LAN failover Interface Description

  !

  interface Management0/0

  nameif management

  security-level 100

  IP 192.168.1.1 255.255.255.0

  management only

  !

  boot system Disk0: / asa861-2-smp - k8.bin

  passive FTP mode

  DNS domain-lookup data

  DNS server-group DefaultDNS

  Server name 172.16.18.21

  Server name 172.16.18.22

  network of the OBJ_INSIDE object - HOSTS_172.21.20.0

  172.21.20.0 subnet 255.255.255.0

  network of the OBJ_DATA object - HOSTS_172.16.18.0

  172.16.18.0 subnet 255.255.255.0

  acl_outside list extended access permit icmp any one

  acl_data list extended access permit icmp any one

  acl_inside list extended access permit icmp any one

  acl_dmz list extended access permit icmp any one

  pager lines 24

  Enable logging

  Within 1500 MTU

  data of MTU 1500

  MTU 1500 DMZ

  Outside 1500 MTU

  management of MTU 1500

  IP local pool vpn_pool1 172.16.22.5 - 172.16.22.250 mask 255.255.255.0

  IP local pool vpn_pool2 172.16.23.5 - 172.16.23.250 mask 255.255.255.0

  failover

  primary failover lan unit

  LAN failover failover GigabitEthernet0/5 interface

  link failover failover GigabitEthernet0/5

  failover interface ip Failover 4.4.4.1 255.255.255.0 ensures 4.4.4.2

  ICMP unreachable rate-limit 1 burst-size 1

  ICMP allow any privileged

  ICMP allow all data

  ICMP allow all DMZ

  ICMP allow all outside

  ASDM image disk0: / asdm - 66114.bin

  don't allow no asdm history

  ARP timeout 14400

  !

  network of the OBJ_INSIDE object - HOSTS_172.21.20.0

  NAT (inside, outside) dynamic 68.71.198.102

  network of the OBJ_DATA object - HOSTS_172.16.18.0

  NAT (data, Outside) 68.71.198.102 Dynamics

  acl_inside access to the interface inside group

  Access-group acl_data in the interface data

  Access-group acl_dmz in DMZ interface

  Access-group acl_outside in interface outside

  Route outside 0.0.0.0 0.0.0.0 68.71.198.97 1

  Route of data 172.16.5.0 255.255.255.0 172.16.18.3 1

  Route data 172.16.10.0 255.255.255.0 172.16.18.3 1

  Route of data 172.16.13.0 255.255.255.0 172.16.18.3 1

  Route of data 172.16.14.0 255.255.255.0 172.16.18.3 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  identity of the user by default-domain LOCAL

  the ssh LOCAL console AAA authentication

  Enable http server

  http 172.21.20.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

  Telnet timeout 5

  SSH 172.21.20.0 255.255.255.0 inside

  SSH timeout 5

  Console timeout 0

  No vpn-addr-assign aaa

  No dhcp vpn-addr-assign

  management of 192.168.1.2 - dhcpd address 192.168.1.254

  enable dhcpd management

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  allow outside

  AnyConnect essentials

  AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1

  AnyConnect enable

  internal AnyConnectClientPolicy group strategy

  attributes of Group Policy AnyConnectClientPolicy

  WINS server no

  value of 172.16.18.21 DNS server 172.16.18.22

  client ssl-VPN-tunnel-Protocol ikev2

  plexxus.ca value by default-field

  the address value vpn_pool1 vpn_pool2 pools

  dmradmin 1ZwOzoVS5TWIvR0h encrypted password username

  type tunnel-group AnyConnectClientProfile remote access

  attributes global-tunnel-group AnyConnectClientProfile

  Group Policy - by default-AnyConnectClientPolicy

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  Cryptochecksum:659360d147ccf882ab6cbb6e170ca8d2

  : end

  I'm glad to hear that you fixed

  Please see this:

  network of the VPN_POOL object

  subnet 192.168.1.0 255.255.255.0--> adapt this to your real IP address range

  !

  the INTERNAL_NETWORKS_VPN object-group network

  object-network 192.168.2.0 255.255.255.0---> that corresponds to the internal network, you want to achieve through the tunnel.

  !

  NAT (inside, outside) 1 static source INTERNAL_NETWORKS_VPN INTERNAL_NETWORKS_VPN static destination

  VPN_POOL VPN_POOL-route search

  It's pretty much the NAT exempt 8.3, 8.4, 8.6...

  Additional information:

  ASA Pre-8, 3 8.3 NAT configuration examples

  Keep me posted.

  Thank you.

  Portu.

  Please note all useful messages.

• E HP6830 all-in-one: with disabilities... network configurations please help

  I'm having the same problem.  Just Bough this printer 2 weeks ago staples.  Everything I select, wifi, network, fax even scanning e-mail I receive a message indicating "built in the configuration of the network have been disable contact administrator or the person who created the printer.»

  Help, please.

  Hi @Babyd1967,

  Welcome to the Forums of HP Support! I understand that you can not access anything whether it's on the screen of the printer without administrator rights. I want to help you solve this problem. If this helps you to find a solution, please click on the button "Accept as Solution" down below in this message. If you want to say thanks for my effort to help, click on the 'Thumbs Up' to give me a Kudos.

  I can send you the reset of the printer in a private message. This should take care of this problem.
  In the forum next to your handle name simply click on the envelope to see.

  Please let me know the results and if there is anything else I can help you. Thank you.

• stuck on configuring updates, help

  I upgraded my pc, it is stuck on configuring updates 1 of 3, 0%, which can do to restore it, I have no cd boot and you cannot get into safe mode, I am running vista, please help

  Hi Julie1212,

  I suggest to organize for a Windows Vista disc that is the same edition as it is installed on your computer, then try the steps in the Microsoft Knowledge Base.

  An update is not installed successfully when you try to install the update in Windows Vista and Windows 7

  http://support.Microsoft.com/kb/949358

  I hope this helps.

• Configure AnyConnect (Mobile) on ASA5505

  I found some tutorials and guides on how to Setup on an ASA5505 AnyConnect, but I wanted to check before to make sure I was going to the right direction.

  Installation program:

  I have a very simple installation and the basic objective.  I have currently just a laptop on my ASA5505 E0/1 and then the ASA is configured with a static IP connected to the Internet.  I have ASA correctly configured and you can browse the web through the laptop.

  I also AnyConnect and AnyConnect Mobile licenses as well.

  Objective:

  I want to configure on the ASA5505 AnyConnect and simply to establish a successful connection to a device mobile android running AnyConnect necessary software on the market.

  ===========

  There are plenty of guides for specifc set ups, but as described, I want to keep it is as simple as possible.

  It would be a good guide to complete this?

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080972e4f.shtml

  Also, I am more comfortable with the CLI. Is it easier to use the ASDM Assistant for this?

  Thanks in advance.

  Hello Joffroi,

  Please check the question as answered so future users can learn from your own resolution

  Kind regards

  Julio

• After you have configured Anyconnect using the client of the wizard is unable to connect to Internet

  Hello

  I have a small Setup w/8.4 ASA - 5520. Outside goes to Internet, the inside is 172.17.0.0/16 network and management is 172.17.2.0/24. VPN IP pool is 172.17.8.0/24.

  After that I configured webvpn with the wizard, I have VPN into a fine, ping other IP switches and routers (ASA is running EIGRP and distributing its static route to the internet to its neighbors). I have Setup nat to allow for Internet access from the inside to the outside, use off interface as the translated source.

  After I VPN in, I am assigned a correct address for my pool VPN (172.17.8.21 for example). I can't ping or connect on the Internet however. Newspapers reveal nothing, I don't see any rejected packets. I can't reach the management either network. The management network is a switch that has all the ports of the management of the different switches, faders load, etc on this subject, but I can't access it.

  I wonder what type of NAT configuration, I have to do here and how to I'm to deny access to the Web interface and management, but nothing appears in newspapers despite debugging setup and open the firewall until completely bringing all traffic.

  The security level is 90 for the Interior and 0 to 100 outside management. The possibility of allowing equal security level interfaces pass traffic is selected. I got inside and the management to 100 before and it did not work with VPN.

  Please help, I do not have my config ASA handy ATM, but I will by hand in a few hours.

  I was wondering if anyone has recommendations on the use of NAT so I can get access, I need.

  Thanks in advance

  Patrick,

  Do not have access to an ASA myself so the commands below are not soundproof.

  But I guess if you're missing config NAT, it would be the document describing:

  https://supportforums.Cisco.com/docs/doc-11640

  To access the management, good show use some newspapers :-)

  show xlate det | I have IP_ADD (for source and destination IP)

  Show logg. I have IP_ADD (make sire logging is enabled for buffering on the level of information and to do for the source and destination)

  Marcin

• Bangin blackBerry smartphones ' my head against a wall re: Internet e-mail configuration. Help, please! I'm desperate.

  Argh...

  Have been trying for days to set up my email of internet.

  I bought an unlocked 8310 (AT & T) curve for my T-mobile account.  Everything works so far, including browsing the web, but I can't configure my Internet email.

  There is absolutely no icon on the phone to do this, I searched all the options that was suggested to me.  The only option I have is to set up an Email from the company, which I did not.  I have been in discussion with AT & T and TMobile and have entered my PIN and IMEI code on both sites to try to set up, with nothing working.

  All the ideas for the poor ole' me?

  Thank you

  Sarah

  

  Phew... I had figured it out.  TMobile sent me incorrect service for my telephone books.  Thanks for responding!

• Configure asa5520 help

  I connected my asa5520 as:

  CAT6 (port Access)-> ASA5520 (outside)

  CAT6 (trunk port)-> (inside)-> vlan101 and vlan 102

  because I need people to see inside the machines, I used "no-nat-control."

  asa5520 configured as:

  interface GigabitEthernet0/0

  No nameif

  no level of security

  no ip address

  !

  interface GigabitEthernet0/0,101

  VLAN 101

  nameif vlan101

  security-level 100

  10.1.1.1 IP address 255.255.255.0

  !

  interface GigabitEthernet0/0,102

  VLAN 102

  nameif vlan102

  security-level 100

  10.1.2.1 IP address 255.255.255.0

  !

  interface GigabitEthernet0/1

  nameif outside

  security-level 0

  IP 10.1.3.9 255.255.255.0

  access outside the permitted scope icmp a session list

  access outside the interface allowed icmp extended outside the vlan101 interface list

  outside access-group in external interface

  on the cat6, I add static route:

  Route IP 10.1.1.0 255.255.255.0 10.1.3.1

  IP route 10.1.2.0 255.255.255.0 10.1.3.1

  Currently:

  in the box to asa5520, I ping out any machine, but not inside any machine (10.1.1.12 or 10.1.2.12)

  from the outside, I can ping external interface (10.1.3.9), not in interface 10.1.1.1 and not inside the 10.1.1.12 machine

  inside the 10.1.1.12 machine, cannot ping anything.

  Please advice me what I did wrong?

  Thanks in advance

  Did you apply the "permit same-security-traffic inter-interface" command? This is to allow communication between the same interfaces of security (enabled by the inter-interface same-security-traffic command) offers the following benefits:

  ? You can configure more than 101 communication interfaces. If you use different levels for each interface, you can configure only one interface per level (0 to 100).

  ? You can allow traffic to flow freely between all the interfaces of security even without access lists.

  This is necessary because both of your interfaces Vlan101 and Vlan102 are set to use the same level of security 100:

  HostName (config) # permit same-security-traffic inter-interface

  hostname (config) #static (vlan101, vlan102) 10.1.1.0 10.1.1.0 netmask 255.255.255.0

  hostname (config) #static (vlan102, vlan101) 10.1.2.0 10.1.2.0 255.255.255.0 netmask

  http://www.Cisco.com/en/us/customer/products/ps6120/products_command_reference_chapter09186a008063f0fb.html#wp1283601

  Pls note all useful message (s)

  HTH

  AK

• VPN between a router from 1721 to a Juniper srx 240

  Hello

  Is it possible to set up a vpn tunnel on a 1721 router that uses the following ios:

  C1700-y7 - mz.124 - 13b .bin

  I thought I had read somewhere that the tunnels were not supported in the 1700s, but wanted to make sure. If they are I would like to know if they are supported in ios preceding.

  Thank you.

  Yes, 1721 supports the termination of VPN tunnels and you need IP/firewall and IPSec 56 or sets features IOS IP/firewall and IPSec 3DES.

  Here is the Cisco1721 router for your reference data sheet:

  http://www.Cisco.com/en/us/products/HW/routers/ps221/products_data_sheet09186a00800920ec.html

  However, please note that Cisco1721 has reached EOL:

  http://www.Cisco.com/en/us/prod/collateral/routers/ps221/prod_end-of-life_notice0900aecd8044473f.html

  In addition, the current ios you have: c1700-y7 - mz.124 - 13b .bin does not support IPSec. You need to download IOS with IP/firewall and IPSec 56 OR / IP/firewall and IPSec 3DES IOS feature sets to support IPSec.

  I hope this helps.

• AnyConnect Configuration problem

  Hi people,

  I am configuring anyconnect for purposes of test on our corporate network.

  I have an ASA connection to a LAN with a class B network configured on interface inside and another network of class B on the external interface.

  the routing is configured to inside the network and works well, ena and to the external network, I put a default route pointing to a switch that is connected to our router BGP Corporate!

  I have configured the Anyconnect with all necessary and all policies, but I can't any guest to external network.

  The ASA does not record anything so I wonder if any attempt even arrive at all or not.

  I have not configured NATexemption as I assume that this is not necessary, because I do not have any nating on this unit.

  Here is my configuration:

  Route outside 0.0.0.0 0.0.0.0 x.x.x.x (next hop switch)
  Inside x.x.0.0 255.255.0.0 route x.x.x.x 1

  Crypto ipsec pmtu aging infinite - the security association
  Crypto ca trustpoint ASDM_TrustPoint1
  registration auto
  name of the object CN = anyconnect-test
  Proxy-loc-transmitter
  Configure CRL
  trustpool crypto ca policy
  string encryption ca ASDM_TrustPoint1 certificates
  certificate a595f554

  WebVPN
  allow outside
  AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
  AnyConnect enable
  tunnel-group-list activate
  internal group anyconnect strategy
  attributes of the strategy group anyconnect
  client ssl-VPN-tunnel-Protocol
  Split-tunnel-policy tunnelall
  WebVPN
  AnyConnect Dungeon-Installer installed
  AnyConnect ask to activate default anyconnect timeout 10

  username xxxxxx encrypted password xxxxxxxxxxxxxx

  tunnel-group anyconnect type remote access
  tunnel-group anyconnect General attributes
  Connect-Net address pool
  strategy-group-by default anyconnect
  tunnel-group anyconnect webvpn-attributes
  allow group-alias anyconnect-test

  Any help would be appreciated.

  See you soon.

  Hello

  In this case, you need to resolve to see what it could be,

  Could you do the following:

  Allow the AnyConnect inside and try to connect from any inside the host of the IP address of the inside:

  WebVPN
  allow inside

  * If the user is able to connect from the inside, make sure that the VPN allowed Sysopt command is enabled:

  See the race all the sysopt

  No timewait sysopt connection
  Sysopt connection tcpmss 1380
  Sysopt connection tcpmss minimum 0
  Sysopt connection VPN - allowed--> is the one that counts
  Sysopt connection VPN-reclassify
  No sysopt preserve-vpn-stream connection
  no RADIUS secret ignore sysopt
  No outside sysopt noproxyarp
  No inside sysopt noproxyarp

  To use another port instead of 443:

  WebVPN

  port 4443--> this port is an example

  * Then try to access from the outside once again, if you are not in a position to ensure that the MTU on the external interface is 1400 or 1500

  * If the MTU is fine, go ahead and set up a capture on the external interface and a capture of fall as well, then we can see if the SAA is intercept traffic and a fall. If traffic isn't not being the ASA could be an ISP issue:

  Capture outdoors:

  capture of CAPE ip match host interface

  See the capture CAP--> appear on the CLI capture and show you if 443 443 TCP UDP packets receive ASA, and it will tell you if the ASA sends a response to the client

  type of projection to capture asp - file all the circular buffer

  See the drop shot | Inc. --> This will show if the ASA is declining by the session and also to give a reason.

  Note: If nothing is shown are of course the next hop IP address in front of the ASA (ISP), that it does not obstruct the ports.

  Please don't forget to rate and score as correct the helpful post!

  Let me know how it works and if extra help is needed!

  Kind regards

  David Castro

• AnyConnect Configuration

  So I had to take this cisco AnyConnect running on an asa5550 9.1 (7) 4. I am familiar with the heavy cisco client configuration, but I need to understand all aspects of AnyConnect. Can anyone provide a quick checklist of all the point needed for AnyConnect work?

  Very appreciated

  Hello

  You can check this link for configuration Anyconnect and work:

  http://www.Cisco.com/c/en/us/TD/docs/security/ASA/asa80/configuration/gu...

  Kind regards

  Aditya

  Please evaluate the useful messages and mark the correct answers.

• AnyConnect with hostscan configuration

  Hello Experts

  If one please send me the details of configuration for "Anyconnect with hostscan" firewall cisco-5545-x series.

  I really appreciate your response as soon as possible.

  This is fine in the section on "Configuration AnyConnect Hostscan" ASA Configuration Guide.

  Also, please see the section AnyConnect Admin Guide 'host Scan and Posture Module configuration'.

• AnyConnect: User based authentication certificate filtering Configuration

  Hello colleagues in the network.

  recently I needed to configure AnyConnect SSL VPN with certificate authentication to meet the needs of connection at the request of the features of Cisco Jabber.

  Everything is ok, but I need to filter users based on their personal certificate information. For example - all those who have a personal certificate from our CA can now access this VPN. I want to set the users by e-mail of the certificate and only these users are granted access.

  I used this command:

  WebVPN

  allow outside

  AnyConnect image disk0:/anyconnect-win-3.1.04072-k9.pkg 1

  AnyConnect enable

  tunnel-group-list activate

  Certificate-Group-map Cert - filter 10 company-Jabber

  map of encryption ca Cert certificate - filter 10

  name of the object attr eq ea [email protected] / * /

  The problem is that I have to go can visit his profile - if I change [email protected] / * / to

  On the AnyConnect client - I connect to the GroupURL of the connection profile Company-Jabber

  Hi Alexandre

  There are several ways to approach this and this depends somewhat on the rest of the config, for example if you have other groups of tunnel etc..

  I guess the easiest way (if it does not interfere with the rest of your configuration) is to add something like this:

  crypto ca certificate map Cert-Filter 65535 subject-name ne ""

  This would attract all users/certificates does not not from your previous rules.

  Under webvpn you map these users to another tunnel-group (connection profile):

  certificate-group-map Cert-Filter 65535 NoAccess

  And configure the NoAccess group so that access is denied (for example, by setting simultaneous connections to 0 in the corresponding Group Policy).

  Other means would be to use DAP (dynamic access policies) to pretty much the same as the certmap, or permission to LDAP (for example retrieves the user name for the certificate, then perform an LDAP search to see if the user is allowed to use the VPN - in this scenario, there is no need to list all the users on the ASA but for example you need to create a new group on your LDAP server that contains all VPN users).

  Let me know if you want to go further in the foregoing

  see you soon

  Herbert

• AnyConnect error is not reliable, it helps

  I have a client whose client Anyconnect began to appear the warning not approved when they connect later.  Original connections come out fine, and the certificate does not work.  What I noticed however is the URL of watch did not, but the INVESTIGATION period, so it's to see the SS and not CA when it connects. Is there anything else I need to do to prevent this?

  Oh, Yes. Thanks for the explanation.

  You must configure AnyConnect profile with the domain, COMPLETE the following:

  Configuration--> remote access VPN-->--> profile (Client) network access Client AnyConnect--> add

  Then change the profile under the menu "server list":

  In the host name field, type the FQDN and do not fill the field to the host address.

  Here is the information for your reference:

  http://www.Cisco.com/en/us/docs/security/vpn_client/AnyConnect/anyconnect31/Administration/Guide/ac03vpn.html#wp1199717

• AnyConnect + possible PSK (pre-shared key) as under with cisco vpn client ikev1 and ikev2

  Is it possible to create a VPN Anyconnect of RA with just the name of user and password + pre-shared key (Group) for the connection, as could do for ikev1 with cisco VPN client? I am running 8.4.X ASA code and looks like tunnel-group commands have 8.2.X somewhat change. If you change the group type of the tunnel for remote access, now there is no option for IKEv2 PSK. This is only available when you choose the type

  Type of TG_TEST FW1 (config) # tunnel - group?

  set up the mode commands/options:
  Site IPSec IPSec-l2l group
  Remote access using IPSec-IPSec-ra (DEPRECATED) group
  remote access remote access (IPSec and WebVPN) group
  WebVPN WebVPN Group (DEPRECATED)

  FW1(config-tunnel-General) # tunnel - group TG_TEST ipsec-attributes
  FW1(config-tunnel-IPSec) #?

  configuration of the tunnel-group commands:
  any required authorization request users to allow successfully in order to
  Connect (DEPRECATED)
  Allow chain issuing of the certificate
  output attribute tunnel-group IPSec configuration
  mode
  help help for group orders of tunnel configuration
  IKEv1 configure IKEv1
  ISAKMP policy configure ISAKMP
  not to remove a pair of attribute value
  by the peer-id-validate Validate identity of the peer using the peer
  certificate
  negotiation to Enable password update in RADIUS RADIUS with expiry
  authentication (DEPRECATED)

  FW1(config-tunnel-IPSec) # ikev1?

  the tunnel-group-ipsec mode commands/options:
  pre-shared key associate a key shared in advance with the connection policy

  I'm getting old so I hope that it is not in another complaint curmudgeonly on the loss of functionality. :)

  Many small businesses do not want to invest in the PKI. It is usually a pain to deploy, backup, make redundant, etc..

  But it would be nice to have a bit more security on VPN other than just the connections of username and password.

  If this is not possible, it is possible to configure the Anyconnect customer to IKEv1 with PSK and name at the level of the Group client?

  If this is not possible, WTH did cisco end customer VPN cisco as a choice of VPN connection (other than to get more fresh mail of license)?

  I really hope that something like this exists still!

  THX,

  WR

  You are welcome

  In addition to two factors, you can also do double authentication (ie the two using the user name and password). Each set of credentials can come from a Bank of different identities.

  With this scheme, you can can configure a local user name (common) with password on the SAA (think of it as your analog PSK) and the other be the AD user identification information.