Cannot access within LAN of Cisco Anyconnect
I'm new to the firewall and try to get my Anyconnect test configuration to connect to addresses within my Local network. The Anyconnect client connects easily, I can get to addresses Internet and tracer package told me it falls to phase 6, svc-webvpn. Can someone post my config? I don't know I'm missing something pretty obvious. Config is pasted below:
!
interface Ethernet0/0
Description< uplink="" to="" isp="">
switchport access vlan 20
!
interface Ethernet0/1
Description< inside="">
switchport access vlan 10
Speed 100
full duplex
!
interface Ethernet0/2
Description< home="" switch="">
switchport access vlan 10
!
interface Ethernet0/3
switchport access vlan 10
!
interface Ethernet0/4
!
interface Ethernet0/5
Shutdown
!
interface Ethernet0/6
Shutdown
!
interface Ethernet0/7
Shutdown
!
interface Vlan10
nameif inside
security-level 100
IP 192.168.1.99 address 255.255.255.0
!
interface Vlan20
nameif OUTSIDE
security-level 0
DHCP client dns update
IP address dhcp setroute
!
Vlan30 interface
No nameif
no level of security
no ip address
!
Banner motd
Banner motd +... +
Banner motd |
Banner motd | Any unauthorized use or access prohibited * |
Banner motd |
Banner motd | The Officer allowed the exclusive use.
Banner motd | You must have explicit permission to access or |
Banner motd | configure this device. All activities performed.
Banner motd | on this unit can be saved and violations of.
Banner motd | This strategy may result in disciplinary action, and |
Banner motd | may be reported to the police authorities. |
Banner motd |
Banner motd | There is no right to privacy on this device. |
Banner motd |
Banner motd +... +
Banner motd
boot system Disk0: / asa824-k8
passive FTP mode
clock timezone cst - 6
clock to summer time recurring cdt
permit same-security-traffic intra-interface
ICMP-type of object-group DEFAULT_ICMP
Description< default="" icmp="" types="" permit="">
response to echo ICMP-object
ICMP-unreachable object
ICMP-object has exceeded the time
object-group network obj and AnyConnect
host of the object-Network 192.168.7.20
host of the object-Network 192.168.7.21
host of the object-Network 192.168.7.22
host of the object-Network 192.168.7.23
host of the object-Network 192.168.7.24
host of the object-Network 192.168.7.25
access-list 101 extended allow icmp a whole
!
Note access-list ACL_OUTSIDE < anyconnect="" permit=""> >
ACL_OUTSIDE list extended access permitted tcp everything any https eq
ACL_OUTSIDE list extended access permit icmp any any DEFAULT_ICMP object-group
!
VPN_NAT list extended access permit ip host 192.168.7.20 all
VPN_NAT list extended access permit ip host 192.168.7.21 all
VPN_NAT list extended access permit ip host 192.168.7.22 all
VPN_NAT list extended access permit ip host 192.168.7.23 all
VPN_NAT list extended access permit ip host 192.168.7.24 all
VPN_NAT list extended access permit ip host 192.168.7.25 all
access-list extended sheep allowed ip group object obj-AnyConnect 192.168.1.0 255.255.255.0
pager lines 24
Enable logging
timestamp of the record
logging buffered information
logging trap information
exploitation forest asdm errors
MTU 1500 inside
Outside 1500 MTU
mask 192.168.7.20 - 192.168.7.25 255.255.255.0 IP local pool AnyconnectPool
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 645.bin
don't allow no asdm history
ARP timeout 14400
Global (1 interface OUTSIDE)
NAT (INSIDE) 1 192.168.1.0 255.255.255.0
NAT (OUTSIDE) 1 access-list VPN_NAT
Access-group ACL_OUTSIDE in interface OUTSIDE
!
router RIP
network 192.168.1.0
passive-interface OUTSIDE
version 2
!
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
AAA authentication http LOCAL console
Enable http server
http 192.168.1.0 255.255.255.0 inside
http 192.168.2.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Sysopt connection tcpmss 1200
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4688000 association
Crypto-map dynamic dynmap 20 the value transform-set ESP-3DES-SHA
map outside_map 64553-isakmp ipsec crypto dynamic dynmap
outside_map interface card crypto OUTSIDE
!
ISAKMP crypto identity hostname
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
VPN-addr-assign local reuse-delay 120
SSH 192.168.1.0 255.255.255.0 inside
SSH 192.168.2.0 255.255.255.0 inside
SSH timeout 60
Console timeout 0
management-access INTERIOR
DHCP-client broadcast-flag
dhcpd x.x.x.x dns
dhcpd rental 43200
dhcpd ping_timeout 2000
dhcpd auto_config OUTSIDE
!
dhcpd address 192.168.1.150 - 192.168.1.180 inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
NTP 216.229.0.179 Server
SSL encryption, 3des-sha1-aes128-sha1 aes256-sha1 sha1 rc4
localtrust point of trust SSL outdoors
WebVPN
allow outside
AnyConnect essentials
SVC disk0:/anyconnect-win-4.2.01035-k9.pkg 1 image
SVC disk0:/anyconnect-linux-64-4.2.01035-k9.pkg 2 image
Picture disk0:/anyconnect-macosx-i386-4.2.01035-k9.pkg 3 SVC
enable SVC
tunnel-group-list activate
attributes of Group Policy DfltGrpPolicy
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
internal Anyconnect group strategy
attributes Anyconnect-group policy
value x.x.x.x DNS server
VPN-tunnel-Protocol svc
the address value AnyconnectPool pools
type tunnel-group remotevpn remote access
tunnel-group Anyconnect type remote access
tunnel-group Anyconnect General attributes
strategy-group-by default Anyconnect
tunnel-group Anyconnect webvpn-attributes
enable MY_RA group-alias
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
Auto-update 30 3 1 survey period
Update automatic timeout 1
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:d41d8cd98f00b204e9800998ecf8427e
: end
Hello
You are missing a NAT FREE for Anyconnect traffic would allow you to access inside the network.
access-list allowed sheep ip 192.168.1.0 255.255.255.0 192.168.7.0 255.255.255.0
NAT (inside) 0 access-list sheep
Add these two lines in the config file and you should be able to access the network interior.
Kind regards
Aditya
Please evaluate the useful messages and mark the correct answers.
Tags: Cisco Security
Similar Questions
-
CANNOT ACCESS THE LAN WITH THE EASY VPN CONFIGURATION
Hello
I configured easy vpn server in cisco 1905 SRI using ccp. The router is already configured with zone based firewall. With the help of vpn client I can reach only up to the internal interface of the router, but cannot access the LAN from my company. I need to change any configuration of ZBF since it is configured as "deny everything" from outside to inside? If so that all protocols should I match? Also is there any exemption of NAT for VPN clients? Please help me! Thanks in advance.
Please see my full configuration:
Router #sh run
Building configuration...Current configuration: 8150 bytes
!
! Last modification of the configuration at 05:40:32 UTC Wednesday, July 4, 2012 by
! NVRAM config updated 06:04 UTC Tuesday, July 3, 2012 by
! NVRAM config updated 06:04 UTC Tuesday, July 3, 2012 by
version 15.1
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
router host name
!
boot-start-marker
boot-end-marker
!
!
Passwords security min-length 6
no set record in buffered memory
enable secret 5 xxxxxxxxxxx
!
AAA new-model
!
!
AAA authentication login default local
AAA authentication login ciscocp_vpn_xauth_ml_1 local
AAA authorization exec default local
AAA authorization ciscocp_vpn_group_ml_1 LAN
!
!
!
!
!
AAA - the id of the joint session
!
!
No ipv6 cef
IP source-route
no ip free-arps
IP cef
!
Xxxxxxxxx name server IP
IP server name yyyyyyyyy
!
Authenticated MultiLink bundle-name Panel
!parameter-map local urlfpolicy TSQ-URL-FILTER type
offshore alert
block-page message "Blocked according to policy"
parameter-card type urlf-glob FACEBOOK
model facebook.com
model *. Facebook.comparameter-card type urlf-glob YOUTUBE
mires of youtube.com
model *. YouTube.comparameter-card type urlf-glob CRICKET
model espncricinfo.com
model *. espncricinfo.comparameter-card type urlf-glob CRICKET1
webcric.com model
model *. webcric.comparameter-card type urlf-glob YAHOO
model *. Yahoo.com
model yapoparameter-card type urlf-glob PERMITTEDSITES
model *.parameter-card type urlf-glob HOTMAIL
model hotmail.com
model *. Hotmail.comCrypto pki token removal timeout default 0
!
Crypto pki trustpoint TP-self-signed-2049533683
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 2049533683
revocation checking no
rsakeypair TP-self-signed-2049533683
!
Crypto pki trustpoint tti
crl revocation checking
!
Crypto pki trustpoint test_trustpoint_config_created_for_sdm
name of the object [email protected] / * /
crl revocation checking
!
!
TP-self-signed-4966226213 crypto pki certificate chain
certificate self-signed 01
3082022B 30820194 02111101 300 D 0609 2A 864886 F70D0101 05050030 A0030201
2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43647274 31312F30
69666963 32303439 35323236 6174652D 3833301E 170 3132 30363232 30363332quit smoking
encryption pki certificate chain tti
for the crypto pki certificate chain test_trustpoint_config_created_for_sdm
license udi pid CISCO1905/K9 sn xxxxxx
licence start-up module c1900 technology-package datak9
username privilege 15 password 0 xxxxx xxxxxxx
!
redundancy
!
!
!
!
!
type of class-card inspect entire tsq-inspection-traffic game
dns protocol game
ftp protocol game
https protocol game
match icmp Protocol
match the imap Protocol
pop3 Protocol game
netshow Protocol game
Protocol shell game
match Protocol realmedia
match rtsp Protocol
smtp Protocol game
sql-net Protocol game
streamworks Protocol game
tftp Protocol game
vdolive Protocol game
tcp protocol match
udp Protocol game
match Protocol l2tp
class-card type match - all BLOCKEDSITES urlfilter
Server-domain urlf-glob FACEBOOK game
Server-domain urlf-glob YOUTUBE game
CRICKET urlf-glob-domain of the server match
game server-domain urlf-glob CRICKET1
game server-domain urlf-glob HOTMAIL
class-map type urlfilter match - all PERMITTEDSITES
Server-domain urlf-glob PERMITTEDSITES match
inspect the class-map match tsq-insp-traffic type
corresponds to the class-map tsq-inspection-traffic
type of class-card inspect correspondence tsq-http
http protocol game
type of class-card inspect all match tsq-icmp
match icmp Protocol
tcp protocol match
udp Protocol game
type of class-card inspect correspondence tsq-invalid-src
game group-access 100
type of class-card inspect correspondence tsq-icmp-access
corresponds to the class-map tsq-icmp
!
!
type of policy-card inspect urlfilter TSQBLOCKEDSITES
class type urlfilter BLOCKEDSITES
Journal
reset
class type urlfilter PERMITTEDSITES
allow
Journal
type of policy-card inspect SELF - AUX-OUT-policy
class type inspect tsq-icmp-access
inspect
class class by default
Pass
policy-card type check IN and OUT - POLICIES
class type inspect tsq-invalid-src
Drop newspaper
class type inspect tsq-http
inspect
service-policy urlfilter TSQBLOCKEDSITES
class type inspect tsq-insp-traffic
inspect
class class by default
drop
policy-card type check OUT IN-POLICY
class class by default
drop
!
area inside security
security of the OUTSIDE area
source of security OUT-OF-IN zone-pair outside the destination inside
type of service-strategy check OUT IN-POLICY
zone-pair IN-to-OUT DOMESTIC destination outside source security
type of service-strategy inspect IN and OUT - POLICIES
security of the FREE-to-OUT source destination free outdoors pair box
type of service-strategy inspect SELF - AUX-OUT-policy
!
Crypto ctcp port 10000
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
!
crypto ISAKMP policy 2
Group 2
!
ISAKMP crypto client configuration group vpntunnel
XXXXXXX key
pool SDM_POOL_1
include-local-lan
10 Max-users
ISAKMP crypto ciscocp-ike-profile-1 profile
vpntunnel group identity match
client authentication list ciscocp_vpn_xauth_ml_1
ISAKMP authorization list ciscocp_vpn_group_ml_1
client configuration address respond
virtual-model 1
!
!
Crypto ipsec transform-set TSQ-TRANSFORMATION des-esp esp-md5-hmac
!
Profile of crypto ipsec CiscoCP_Profile1
game of transformation-TRANSFORMATION TSQ
set of isakmp - profile ciscocp-ike-profile-1
!
!
!
!
!
!
the Embedded-Service-Engine0/0 interface
no ip address
response to IP mask
IP directed broadcast to the
Shutdown
!
interface GigabitEthernet0/0
Description LAN INTERFACE-FW-INSIDE
IP 172.17.0.71 255.255.0.0
IP nat inside
IP virtual-reassembly in
security of the inside members area
automatic duplex
automatic speed
!
interface GigabitEthernet0/1
Description WAN-INTERNET-INTERNET-FW-OUTSIDE
IP address xxxxxx yyyyyyy
NAT outside IP
IP virtual-reassembly in
security of the OUTSIDE member area
automatic duplex
automatic speed
!
interface Serial0/0/0
no ip address
response to IP mask
IP directed broadcast to the
Shutdown
no fair queue
2000000 clock frequency
!
type of interface virtual-Template1 tunnel
IP unnumbered GigabitEthernet0/0
ipv4 ipsec tunnel mode
Tunnel CiscoCP_Profile1 ipsec protection profile
!
local IP SDM_POOL_1 172.17.0.11 pool 172.17.0.20
IP forward-Protocol ND
!
no ip address of the http server
local IP http authentication
IP http secure server
!
IP nat inside source list 1 interface GigabitEthernet0/1 overload
IP route 0.0.0.0 0.0.0.0 yyyyyyyyy
IP route 192.168.1.0 255.255.255.0 172.17.0.6
IP route 192.168.4.0 255.255.255.0 172.17.0.6
!
access-list 1 permit 172.17.0.0 0.0.255.255
access-list 100 permit ip 255.255.255.255 host everything
access-list 100 permit ip 127.0.0.0 0.255.255.255 everything
access-list 100 permit ip yyyyyy yyyyyy everything
!
!
!
!
!
!
!
!
control plan
!
!
!
Line con 0
line to 0
line 2
no activation-character
No exec
preferred no transport
transport of entry all
output transport lat pad rlogin lapb - your MOP v120 udptn ssh telnet
StopBits 1
line vty 0 4
transport input ssh rlogin
!
Scheduler allocate 20000 1000
endA few things to change:
(1) pool of IP must be a single subnet, it is not the same subnet as your subnet internal.
(2) your NAT ACL 1 must be changed to ACL extended for you can configure NAT exemption, so if your pool is reconfigured to be 10.10.10.0/24:
access-list 120 deny ip 172.17.0.0 0.0.255.255 10.10.10.0 0.0.0.255
access-list 120 allow ip 172.17.0.0 0.0.255.255 everything
overload of IP nat inside source list 120 interface GigabitEthernet0/1
No inside source list 1 interface GigabitEthernet0/1 ip nat overload
(3) OUT POLICY need to include VPN traffic:
access-list 121 allow ip 10.10.10.0 0.0.0.255 172.17.0.0 0.0.255.255
type of class-card inspect correspondence vpn-access
game group-access 121
policy-card type check OUT IN-POLICY
vpn-access class
inspect
-
one of the VM cannot access network LAN
Hello
I configured 3 VM on an ESXi 4.1 (see attached jpg file). one of the virtual machine (GSPPBPCDBVM), it cannot access the network LAN, even cannot ping Bridge but can ping GSPPBPCVM after I walk today, previously, it was ok. The other 2 VM can access LAN network. What could be the problem?
GSPPBPCVM (128.1.8.x)
GSPPBPCDBVM (128.1.8.x)
AEPAD (10.8.1.x)
vmnic1 (to connect to the local network virtual 128.1.8.x)
vmnic0 (to connect to the local network virtual 10.8.1.x)
Thank you and best regards,
Kelvin
With the configuration you have posted, you have a 50/50 chance that none of your VM will have access to the network, since you have 2 NICs connected to two different VLANS and virtual machines are assigned to these network cards based on the virtual switch port (assuming you use the default settings).
To properly set up the network, you have two options:
1.) VLAN tagging on the physical switch ports (what you have)
In this case, you will need to create a second vSwitch and attach the second NETWORK card to this switch. Then connect virtual machines to the vSwitch and port group that is connected to the switch port VLAN corresponding physics.
2.) VLAN tagging on the virtual port group (this is what I recommend)
Configure the ports on your physical switch as the trunk (or ports 'labelled' If you use Procurve switches), create another port VM on vSwitch0 group and set up VLAN tags on the gropus (VMKernel, VM Network1, VM Network2) port
Take a look at http://www.vmware.com/files/pdf/virtual_networking_concepts.pdf for more information.
André
-
Cannot access ' inside' LAN of AnyConnect VPN
Hello. I am having trouble with my VPN connection where I can connect to it very well, and access the internet, but I can't access the internal network. Anyone have any ideas on what I can check to solve that?
I think that the suggestion concerning the exemption of NAT is very good. If that is not the issue, then I have some other suggestions.
-with the session created VPN review information the AnyConnect and look in the route Details tab and be sure that these LAN addresses appear as secure routes.
-check that the devices in the local network that you can not reach a route to addresses in the pool of the VPN.
HTH
Rick
-
RV320 VPN cannot access peripheral LAN using iPad
With the help of RV320, firmware 1.1.1.06
LAN 192.168.1.x 255.255.255.0
VPN 192.168.09.100 to 192.168.09.150
I need to access a device on the local network using this VPN connection from iPad. The Unit received address DHCP on LAN, broadcasts its presence every second on the Port 4992.
When it is on the LAN, the iPAD sees the presence of broadcasting and accesses the device without problem. When I VPN in, easy VPN works well. I configured the firewall of the router as the rules:
Allow All traffic [1] LAN 192.168.9.100 ~ 192.168.9.150 192.168.1.1 ~ 192.168.1.255 Always
Allow All traffic [1] LAN 192.168.1.1 ~ 192.168.1.255 192.168.9.100 ~ 192.168.9.150 Alway
If I first connect to the device when the iPad is on the local network, I turn off WiFi and connect through the VPN, I can continue to control the device. However, if I'm not connected to the device locally first, I see the presence broadcast on port 4992 when it connects first via the VPN. Broadcasting does not reach the iPad from a 192.168.1.x device connected 192.168.9.x.
What is the correct way for the iPad on the 192.168.9.x, see the dissemination of 192.168.1.x?
Hello
Broadcasts will not be sent on the VPN tunnel. The only traffic that will pass from the LAN to your customer's traffic specifically aimed at it, otherwise the router send him outside. Looks like your presence Pack is a show, so all VPN clients won't be able to see.
I think that when you connect locally you are picking up on the broadcast and then when you go to the VPN that has not passed yet, so why does it work if you connect locally first.
Hope that helps a little,
Christopher Ebert - Advanced Network Support Engineer
Cisco Small Business Support Center
* Please note the useful messages *.
-
VPN works, but cannot access the LAN...
I have cisco vpn client connection to a 1721 at the office. the client connects and I can access the office LAN but but not the local network. I have the box checked in client vpn to allow access to the local network. Help, please!
Thank you!
Matt
Here is the config:
Current configuration: 3901 bytes
!
version 12.2
horodateurs service debug datetime msec
Log service timestamps datetime msec
encryption password service
!
Cerberus hostname
!
start the system flash c1700-k9o3sy7 - mz.122 - 11.T10.bin
AAA new-model
!
!
RADIUS AAA server group SERVERS RADIUS
auth-port 1645 192.168.69.1 Server acct-port 1646
!
AAA authentication login LOGIN group SERVERS RADIUS local
local NETGROUPAUTH AAA authorization network
AAA - the id of the joint session
!
username mattheff password xxx
username mikeheff password xxx
clock timezone CST - 6
clock to summer time recurring CDT 2 Sun Mar 2:00 1 Sun Nov 02:00
IP subnet zero
!
!
IP domain name heffnet.net
name of the IP-server 68.94.156.1
name of the IP-server 68.94.157.1
DHCP excluded-address IP 192.168.69.1 192.168.69.99
DHCP excluded-address IP 192.168.69.111 192.168.69.254
!
dhcp HEFFNET_LAN_POOL_1 IP pool
network 192.168.69.0 255.255.255.0
router by default - 192.168.69.254
Server DNS 68.x.x.1 68.94.157.1
!
audit of IP notify Journal
Max-events of po verification IP 100
VPDN enable
!
VPDN-group pppoe
demand dial
Protocol pppoe
!
!
!
crypto ISAKMP policy 3
BA 3des
preshared authentication
Group 2
!
Configuration group VPNGROUP crypto isakmp client
8mathef8 key
68.x.x.1 DNS 68.94.157.1
heffnet.net field
pool VPN_CLIENT_POOL
ACL 102
!
!
Crypto ipsec transform-set esp-3des esp-sha-hmac VPNSET1
!
crypto dynamic-map 10 DYNMAP
game of transformation-VPNSET1
!
!
list of authentication of card crypto VPNCLIENTMAP customer LOGIN
list of crypto isakmp NETGROUPAUTH VPNCLIENTMAP card authorization
crypto card for the VPNCLIENTMAP client configuration address respond
card crypto VPNCLIENTMAP 10-isakmp dynamic ipsec DYNMAP
!
!
!
!
interface Loopback0
IP address 1.1.x.x.255.255.252
!
ATM0 interface
Heffnet WAN/SBC DSL Interface Description
no ip address
No atm ilmi-keepalive
PVC 0/35
PPPoE-client dial-pool-number 69
!
DSL-automatic operation mode
no fair queue
!
interface FastEthernet0
Heffnet LAN Interface Description
IP 192.168.69.254 255.255.255.0
IP nat inside
IP tcp adjust-mss 1452
route VPN_ROUTE_MAP card intellectual property policy
automatic speed
!
interface Dialer69
MTU 1492
the negotiated IP address
NAT outside IP
encapsulation ppp
Dialer pool 69
PPP chap hostname cerberus
PPP chap password xxx
PPP pap sent-username [email protected] / * / password xxx
card crypto VPNCLIENTMAP
!
local IP VPN_CLIENT_POOL 192.168.70.200 pool 192.168.70.253
IP nat inside source list interface INTERNALLY Dialer69 overload
!
IP classless
IP route 0.0.0.0 0.0.0.0 Dialer69
no ip address of the http server
!
!
INTERNAL extended IP access list
deny ip 192.168.69.0 0.0.0.255 192.168.70.0 0.0.0.255
IP 192.168.69.0 allow 0.0.0.255 any
!
record 192.168.69.1
access-list 101 permit ip 192.168.69.0 0.0.0.255 192.168.70.0 0.0.0.255
access-list 102 permit ip 192.168.69.0 0.0.0.255 any
!
VPN_ROUTE_MAP allowed 10 route map
corresponds to the IP 101
set ip next-hop 1.1.1.2
!
alias exec s show ip interface brief
alias exec sr show running-config
!
Line con 0
privilege level 15
Synchronous recording
line to 0
privilege level 15
Synchronous recording
line vty 0 4
privilege level 15
Synchronous recording
line vty 5 15
privilege level 15
Synchronous recording
!
Scheduler allocate 4000 1000
end
Hi Matt,
The config looks good. Please make sure that you get a route to 192.168.69.0 255.255.255.0 network only after the connection to the VPN client. Please also correspond to the exit "route print" before and after the connection. One last thing, I hope that the local network is not 192.168.69.0.
HTH,
Please rate if this helps,
Kind regards
Kamal
-
Remote VPN cannot access devices LAN or internet
So I have a server and a computer inside that I can access through an ASA 5505 with ASA 9.2 (1) and ASDM 7.2 (1)
The computer on 192.168.1.110 via port 8080 can show me a demo site.
The server on 192.168.1.222 got my DNS, HTTP, FTP, mail and more about it.
Outside, I got a computer (by outside, I hear from the firewall and the cable directly into the computer) on 192.168.20.2 and firewall outside being 192.168.20.1
From the outside I can access the 8080 without problem (and I guess as well with the server, but it is on another default gateway and are not accessible right now). -When I connect through my VPN I am assigned 192.168.30.5 but unable to connect inside the computer through 192.168.1.110:8080.
This will return the error: asymmetrical NAT rules matched for before and back flow; Connection for udp src outdoors: 192.168.30.5/49608 (...) dst inside: 192.168.1.222/53 refused because of the failure of the path reverse NAT.
Somewhere, I had a conflict or a non-created access rule. Anyone who wants to take a shot?
I marked with "BOLD" for what I thought that may be the cause.
ciscoasa (config) # sh running-config
: Saved
:
ASA Version 9.2 (1)
!
ciscoasa hostname
activate 8Ry2YjIyt7RRXU24 encrypted password
volatile xlate deny tcp any4 any4
volatile xlate deny tcp any4 any6
volatile xlate deny tcp any6 any4
volatile xlate deny tcp any6 any6
volatile xlate deny udp any4 any4 eq field
volatile xlate deny udp any4 any6 eq field
volatile xlate deny udp any6 any4 eq field
volatile xlate deny udp any6 any6 eq field
2KFQnbNIdI.2KYOU encrypted passwd
names of
192.168.30.5 mask - 192.168.30.200 local pool Pool of IP IP 255.255.255.0
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.254 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
address 192.168.20.1 255.255.255.0
!
boot system Disk0: / asa921 - k8.bin
passive FTP mode
permit same-security-traffic intra-interface
network obj_any object
subnet 0.0.0.0 0.0.0.0
object network testServer-8080
host 192.168.1.110
Description of the test server
network of the object server-21
Home 192.168.1.222
Description of the test server
network of the object Server-25
Home 192.168.1.222
Description of the test server
network of the object Server-53
Home 192.168.1.222
Description of the test server
network of the object server-80
Home 192.168.1.222
Description of the test server
network of the object server-443
Home 192.168.1.222
Description of the test server
network of the object server-2525
Home 192.168.1.222
Description of the test server
network of the object server-993
Home 192.168.1.222
Description of the test server
network of the object server-6001
Home 192.168.1.222
Description of the test server
network of the object server-6002
Home 192.168.1.222
Description of the test server
network of the object server-6003
Home 192.168.1.222
Description of the test server
network of the object server-6004
Home 192.168.1.222
Description of the test server
network of the VPN HOST object
192.168.30.0 subnet 255.255.255.0
network of the object inside
host 192.168.1.0
the vpn server object network
Home 192.168.1.222
outside_access_in list extended access permit tcp any object testServer-8080 eq 8080
outside_access_in list extended access permit tcp any object server-21 eq ftp
outside_access_in list extended access permit tcp any object Server-25 eq smtp
outside_access_in list extended access permit tcp any object server-2525 2525 eq
outside_access_in list extended access permit udp any object server-53 eq inactive field
outside_access_in list extended access permit tcp any object server-80 eq www
outside_access_in list extended access permit tcp any object server-443 https eq
outside_access_in list extended access permit tcp any object server-993 993 eq
outside_access_in list extended access permit tcp any object server-6001 eq 6001
outside_access_in list extended access permit tcp any object server-6002 6002 eq
outside_access_in list extended access permit tcp any object server-6003 eq 6003
outside_access_in list extended access permit tcp any object server-6004 eq 6004
outside_access_in to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.30.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 721.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) VPN-dynamic HOSTS within static destination to source Server VPN - vpn server
!
network obj_any object
NAT dynamic interface (indoor, outdoor)
object network testServer-8080
NAT (inside, outside) interface static 8080 8080 tcp service
network of the object server-21
NAT static (inside, inside) of the service ftp ftp tcp interface
network of the object Server-25
NAT (inside, outside) interface static tcp smtp smtp service
network of the object Server-53
NAT static (inside, inside) interface tcp service area
network of the object server-80
NAT (inside, outside) interface static tcp www www service
network of the object server-443
NAT (inside, outside) interface static tcp https https service
network of the object server-2525
NAT (inside, outside) interface static 2525 2525 tcp service
network of the object server-993
NAT (inside, outside) interface static tcp 993 993 service
network of the object server-6001
NAT (inside, outside) interface static tcp 6001 6001 service
network of the object server-6002
NAT (inside, outside) interface static tcp 6002 6002 service
network of the object server-6003
NAT (inside, outside) interface static 6003 6003 tcp service
network of the object server-6004
NAT (inside, outside) interface static service tcp 6004 6004
Access-group outside_access_in in interface outside
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
RADIUS AAA server HSS-auth-server protocol
allow only
AAA-server HSS-auth-server (inside) host 192.168.1.222
Timeout 5
key *.
identity of the user by default-domain LOCAL
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec pmtu aging infinite - the security association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
trustpool crypto ca policy
Crypto isakmp nat-traversal 30
Crypto ikev1 allow outside
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH stricthostkeycheck
SSH timeout 5
SSH group dh-Group1-sha1 key exchange
Console timeout 0dhcpd outside auto_config
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
internal HSSvpn group strategy
attributes of Group Policy HSSvpn
value of server DNS 192.168.1.222
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value outside_access_in ! This value was its own name earlier
HSS.dk value by default-field
type tunnel-group HSSvpn remote access
attributes global-tunnel-group HSSvpn
address IP-pool pool
HSS-auth-server authentication-server-group
Group Policy - by default-HSSvpn
password-management
IPSec-attributes tunnel-group HSSvpn
IKEv1 pre-shared-key *.
tunnel-group HSSvpn ppp-attributes
No chap authentication
no authentication ms-chap-v1
ms-chap-v2 authentication
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:9859258e11364180cf9b3e21173b3f2f
: endHello
"Nat" bold configuration is incorrect, as you would expect.
Replace it with something like this
the object of the LAN network
subnet 192.168.1.0 255.255.255.0NAT (inside, outside) 1 static source LAN LAN to static destination HOST-VPN-VPN-HOST
I also suggest using a separate access the ACL of the Tunnel from Split 'standard' list.
For example
standard SPLIT-TUNNEL access list permit 192.168.1.0 255.255.255.0
Naturally, you must pass the ACL above to used "group policy" .
In addition, if you want to control the incoming connections to VPN users in 'outside_access_in' ACL, then you could change the default settings on the SAA by running the command
No vpn sysopt connection permit
If you need to return back then just to deliver without 'no' in front. Then back to its default value. This does not show in the running configuration by the way.
With this setting all connections from VPN connections should be allowed on the interface ACL interface that ends the VPN connection. If in your case that would be the ACL attached to the 'outside' interface.
Hope this helps :)
-Jouni
-
Hello
I am setting up a VPN on a Cisco ASA 5510 version 8.4 remote access (4) 1.
When I try to connect via the Cisco VPN client software, I am able to connect however I am unable to access network resources.
However, I can ping the servers in the other site that is connected through the VPN site-to site to the main site!
VPN client--> main site (ping times on)--> Site connected with the main site with VPN S2S (successful ping)
Please help me I need to find a solution as soon as POSSIBLE!
Thank you in advance.
Hello
Please remove the NAT exemption and the re - issue the command but with #1, so it will place the NAT as first line:
No nat (SERVERS, external) static source SERVERS_LAN SERVERS_LAN NETWORK_OBJ_10.10.40.8_29 NETWORK_OBJ_10.10.40.8_29 non-proxy-arp-search of route static destination
NAT (SERVERS, external) 1 static source SERVERS_LAN SERVERS_LAN NETWORK_OBJ_10.10.40.8_29 NETWORK_OBJ_10.10.40.8_29 non-proxy-arp-search of route static destination
After re-configured this way, make sure that this command is also available:
Sysopt connection permit VPN
This sysopt will allow traffic regardles any ACL a fall, just in case. Please continue to run a package tracer and post it here,
Packet-trace entry Server icmp XXXXXX 8 0 detailed YYYYY
XXXX--> server IP
AAAA--> VPN IP of the user
Don't forget to do the two steps and a just in case, capture Please note and mark it as correct the useful message!
Thank you
David Castro,
-
On ASA 5505 VPN cannot access remote (LAN)
I have an ASA 5505 upward and running, all static NAT statements I need to forward ports to the internal services such as smtp, desktop remotely and it works very well, however I have set up an IPSEC vpn connection that authenticates to our DC and part works. However, after I connect and cannot ping anything on the local network or access services. I don't know what a NAT statement I have corrected. Here is the config. I really need to get this up and going tomorrow. Thanks for any help.
Tyler
Just remove the line of nat (outside) and ACL outside_nat0_outbound.
And talk about these statements:
IPSec-1 sysopt connection permit... (If it is disabled, you can check with sh run sysopt).
2, crypto isakmp nat traversal 10 or 20
3 no NAT ACL, mention your local subnets as the source and vpn client as the destination.
4, create the other ACL (ST) with different name and source and destination like no nat ACL.
5, then type nat (inside) 0 access-list sheep
6, in the dwgavpn group policy, talk to splittunnel tunnelspecified and mention the tunnel split ACL (ST).
Concerning
-
Windows 2003 cannot access remote network via Cisco VPN
I have two computers at home, an XP Pro SP2 and another is Windows 2003 server SP1. If I set Cisco VPN XP (version 4.6) the Office (ASA 5510), I can access the office network resources. However, if I set the Cisco VPN on 2003, can I? t do the same thing. After studying the two routing tables, I think XP has this road: 192.168.0.0 255.255.0.0 192.168.101.5 192.168.101.5 1, but the 2003 doesn't? t. If I add this route manually (rou? add 192.168.0.0 mask 255.255.255.0 192.168.101.3) 2003, then I can access resources. Why?
tale of 2003 routing.
Active routes:
Network Destination gateway metric Interface subnet mask
0.0.0.0 0.0.0.0 192.168.10.1 192.168.10.3 40
x.x.x.37 255.255.255.255 192.168.10.1 192.168.10.3 1
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
192.168.10.0 255.255.255.0 192.168.10.3 192.168.10.3 40
192.168.10.3 255.255.255.255 127.0.0.1 127.0.0.1 40
192.168.10.255 255.255.255.255 192.168.10.3 192.168.10.3 40
192.168.101.0 255.255.255.0 192.168.101.3 192.168.101.3 10
192.168.101.3 255.255.255.255 127.0.0.1 127.0.0.1 10
192.168.101.255 255.255.255.255 192.168.101.3 192.168.101.3 10
224.0.0.0 240.0.0.0 192.168.10.3 192.168.10.3 40
224.0.0.0 240.0.0.0 192.168.101.3 192.168.101.3 10
255.255.255.255 255.255.255.255 192.168.10.3 192.168.10.3 1
255.255.255.255 255.255.255.255 192.168.101.3 192.168.101.3 1
Default gateway: 192.168.10.1
===========================================================================
Persistent routes:
None
VPN client has not been tested on Win2003. Customer requirements are described here:
http://www.Cisco.com/univercd/CC/TD/doc/product/VPN/client/4_6/relnt/4604cln.htm#wp1024664
and the show to competition of WinXP is supported.
-
IPsec VPN with Cisco AnyConnect and 1921 ISR G2 router
Hello
Is it possible to establish a remote access VPN IPSec using Cisco Anyconnect client with router Cisco ISR G2 1921.
If someone does share it please the sample configuration. as I've been on this topic since last week a.
My Cisco rep recommended I have not try AnyConnect a router ISR or ASR. So I used an Open Source client. Don't say that AnyConnect won't work, just the route I took on my project. I work good known configuration for a 1921 with strongSwan as a Client. It is with IPSEC and IKEV2 using certificates for authentication.
-
I have problems to access the resources within the network when connecting with the Cisco VPN client for a version of 8.4 (3) operation of the IOS Cisco ASA 5510. I tried all new NAT 8.4 orders but cannot access the network interior. I can see traffic in newspapers when ping. I can only assume I have NAT evil or it's because the inside interface of the ASA is on the 24th of the same subnet as the network interior? Please see config below, any suggestion would be appreciated. I configured a VPN site to another in this same 5510 and it works well
Thank you
interface Ethernet0/0
Speed 100
full duplex
nameif outside
security-level 0
IP x.x.x.x 255.255.255.240
!
interface Ethernet0/1
Speed 100
full duplex
nameif inside
security-level 100
IP 10.88.10.254 255.255.255.0
!
interface Management0/0
Shutdown
nameif management
security-level 0
no ip address
!
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
network of the PAT_to_Outside_ClassA object
10.88.0.0 subnet 255.255.0.0
network of the PAT_to_Outside_ClassB object
subnet 172.16.0.0 255.240.0.0
network of the PAT_to_Outside_ClassC object
Subnet 192.168.0.0 255.255.240.0
network of the LocalNetwork object
10.88.0.0 subnet 255.255.0.0
network of the RemoteNetwork1 object
Subnet 192.168.0.0 255.255.0.0
network of the RemoteNetwork2 object
172.16.10.0 subnet 255.255.255.0
network of the RemoteNetwork3 object
10.86.0.0 subnet 255.255.0.0
network of the RemoteNetwork4 object
10.250.1.0 subnet 255.255.255.0
network of the NatExempt object
10.88.10.0 subnet 255.255.255.0
the Site_to_SiteVPN1 object-group network
object-network 192.168.4.0 255.255.254.0
object-network 172.16.10.0 255.255.255.0
object-network 10.0.0.0 255.0.0.0
outside_access_in deny ip extended access list a whole
inside_access_in of access allowed any ip an extended list
11 extended access-list allow ip 10.250.1.0 255.255.255.0 any
outside_1_cryptomap to access extended list ip 10.88.0.0 255.255.0.0 allow object-group Site_to_SiteVPN1
mask 10.250.1.1 - 10.250.1.254 255.255.255.0 IP local pool Admin_Pool
NAT static NatExempt NatExempt of the source (indoor, outdoor)
NAT (inside, outside) static source any any static destination RemoteNetwork4 RemoteNetwork4-route search
NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork1 RemoteNetwork1
NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork2 RemoteNetwork2
NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork3 RemoteNetwork3
NAT (inside, outside) static source LocalNetwork LocalNetwork static destination RemoteNetwork4 RemoteNetwork4-route search
!
network of the PAT_to_Outside_ClassA object
NAT dynamic interface (indoor, outdoor)
network of the PAT_to_Outside_ClassB object
NAT dynamic interface (indoor, outdoor)
network of the PAT_to_Outside_ClassC object
NAT dynamic interface (indoor, outdoor)
Access-group outside_access_in in interface outside
inside_access_in access to the interface inside group
Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
dynamic-access-policy-registration DfltAccessPolicy
Sysopt connection timewait
Service resetoutside
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-ikev1 esp-md5-hmac bh-series
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto-map dynamic dynmap 10 set pfs
Crypto-map dynamic dynmap 10 set transform-set bh - set ikev1
life together - the association of security crypto dynamic-map dynmap 10 28800 seconds
Crypto-map dynamic dynmap 10 kilobytes of life together - the association of safety 4608000
Crypto-map dynamic dynmap 10 the value reverse-road
card crypto mymap 1 match address outside_1_cryptomap
card crypto mymap 1 set counterpart x.x.x.x
card crypto mymap 1 set transform-set ESP-AES-256-SHA ikev1
card crypto mymap 86400 seconds, 1 lifetime of security association set
map mymap 1 set security-association life crypto kilobytes 4608000
map mymap 100-isakmp ipsec crypto dynamic dynmap
mymap outside crypto map interface
crypto isakmp identity address
Crypto isakmp nat-traversal 30
Crypto ikev1 allow outside
IKEv1 crypto ipsec-over-tcp port 10000
IKEv1 crypto policy 5
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 1
life 86400
IKEv1 crypto policy 50
preshared authentication
the Encryption
md5 hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
preshared authentication
aes-256 encryption
sha hash
Group 1
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
Telnet timeout 5
Console timeout 0
management-access inside
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal BACKDOORVPN group policy
BACKDOORVPN group policy attributes
value of VPN-filter 11
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelall
BH.UK value by default-field
type tunnel-group BACKDOORVPN remote access
attributes global-tunnel-group BACKDOORVPN
address pool Admin_Pool
Group Policy - by default-BACKDOORVPN
IPSec-attributes tunnel-group BACKDOORVPN
IKEv1 pre-shared-key *.
tunnel-group x.x.x.x type ipsec-l2l
tunnel-group ipsec-attributes x.x.x.x
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
Excellent.
Evaluate the useful ticket.
Thank you
Rizwan James
-
AnyConnect VPN users cannot access remote subnets?
I googled this until blue in the face without result. I don't understand why Cisco this so difficult? When clients connect to the anyconnect vpn, they can access the local subnet, but cannot access the resources in remote offices. What should I do to allow my anyconnect vpn clients access to my remote sites?
Cisco 5510 8.4
Hello
What are remote sites using as Internet gateway? Their default route here leads to the ASA or have their own Internet gateway? If they use this ASA for their Internet connection while they should already have a default route that leads traffic to the VPN to the pool, even if they had no specific route for the VPN itself pool. If they use their own local Internet gateway and the default route is not directed to this ASA then you would naturally have a route on the remote site (and anything in between) indicating the remote site where to join the pool of 10.10.224.0/24 VPN network.
In addition to routing, you must have configured for each remote site and the VPN pool NAT0
Just a simple example of NAT0 configuration for 4 networks behind the ASA and simple VPN field might look like this
object-group network to REMOTE SITES
object-network 10.10.10.0 255.255.255.0
object-network 10.10.20.0 255.255.255.0
object-network 10.10.30.0 255.255.255.0
object-network 10.10.40.0 255.255.255.0
network of the VPN-POOL object
10.10.224.0 subnet 255.255.255.0
NAT static destination DISTANCE-SITES SITES source (indoor, outdoor) REMOTE static VPN-VPN-POOL
The above of course assumes that the remote site are located behind the interface 'inside' (although some networks, MPLS) and naturally also the remote site networks are made for the sake of examples.
Since you are using Full Tunnel VPN should be no problem to the user VPN transfer traffic to this ASA in question.
My first things to check would be configuring NAT0 on the ASA and routing between remote sites and this ASA (regarding to reach the VPN pool, not the ASA network IP address)
Are you sure that the configuration above is related to this? Its my understanding that AnyConnect uses only IKEv2 and the foregoing is strictly defined for IKEv1?
-Jouni
-
Deactivate the filter driver Cisco AnyConnect Network Access Manager
I hope that it is the community just to post this in.
I was wondering if it is possible to script disable the "Cisco AnyConnect Network Access Manager filter driver" for a LAN connection?
By comparison to the registry before and after it is manually turned off via Control Panel control-> network and Internet-> network-> connection to the Local network connections, I came with:
: remove the filter Cisco AnyConnect Network Access Manager driver
: the list of filters for the LAN adapter
reg delete HKLM\SYSTEM\CurrentControlSet\Control\Class\ {4D36E972-E325-11CE-BFC1-08002BE10318} \0007\Linkage /v FilterList/f: import the Cisco AnyConnect Network Access Manager filter driver
: to the list of filters, excluding the LAN adapter
Reg import linkage - no - lan.reg: remove the filter Cisco AnyConnect Network Access Manager driver
: the network of the LAN adapter config
reg delete HKLM\SYSTEM\CurrentControlSet\Control\Network /v /f Config: import the Cisco AnyConnect Network Access Manager filter driver
: to the network with the exception of the LAN adapter config
Reg import network - no - lan.reg: Remove the adapter LAN of the list of maps where the
: Cisco AnyConnect Network Access Manager filter driver is used
reg delete HKLM\SYSTEM\CurrentControlSet\services\acnamfd\Parameters\Adapters\ {77197E43-5875-469F-A3A5-A97F63A32E0A} /fThis disables 'Cisco AnyConnect Network Access Manager filter driver' to connect to the local network, but it is not automatically to my wireless connection. However, if I manually in a not checked the "Cisco AnyConnect Network Access Manager Filter Driver', the connection automatically changes my wireless.
The end result, I'm looking for must be able to use a wireless connection and at the same time be able to use the connection to the local network, when I connect directly to some work equipment to download the firmware files.
Any thoughts would be greatly appreciated.
Thank you.
Hi Paul,.
Instead of hacking the registry, you can use nvspbind.exe for this task. You can download the tool here. It will be also NAM automatically mode interfaces.
https://Gallery.technet.Microsoft.com/Hyper-V-network-VSP-bind-cf937850
Disable: nvspbind.exe /d "Wireless network connection" csco_acnamfd
activate: nvspbind.exe/e 'Wireless network connection' csco_acnamfd
Thank you.
-
RVL200 SSL VPN: cannot access a remote LAN with iPad2
RVL200 firmware 1.1.12.1
iPad2 cannot access any device on the Remote LAN despite the closed padlock icon.
Is there another App needed? Or how to debug SSL VPN?
Emmanuel,
Were you able to access the LAN devices? Also, have you connected using a Mac or a PC successfully to verify that the devices are available? Sometimes antivirus and firewall software can block access to devices from a remote IP address.
Maybe you are looking for
-
How you people would get 10.2.3?
People- The forum more and more, I see 10.2.3 is available. However, when I use the App Store App and try to look for updates, I get the response "no updates available". Y at - there a trick to this? Thank you!
-
Hello I'm a bit new to these must therefore ask from you experts. Tried to browse this forum, but did not find an answer to this question. I need to get my AV system with only the RJ45 connection network. However, I don't have cables on show so I nee
-
I can't download or add the update of Silverlight that the upgrade to MSE requires, because I get the error code: B888FFFF.
-
Bb 9800 fast Smartphones Battry blackBerry drain
I torch 9800 it loads quickly on the subject in an hour but also quickly drain to the subject hours in. 4 or 5...I changed the battery, but even please tell mehow to extend my battery life
-
2008 mac compatible with photoshop?
We have a Mac which is since 2008 updated with os Yosemite. We are unable to download photoshop, if anyone else has had this problem? Is it because our computer is too old?