AnyConnect VPN is not access to the ASA
Hello
I have an ASA 5512 - x configured as a hub AnyConnect VPN, but when I connect I can not access the firewall... I can ping the address 10.4.11.2 but I can not connect... No idea what to do? It's the running configuration:
: Saved
:
ASA 1.0000 Version 2
!
asa-oi hostname
domain xx.xx.xx.xx
activate 7Hb0WWuK1NRtRaEy encrypted password
2KFQnbNIdI.2KYOU encrypted passwd
names of
1.1.1.1 DefaultGW-outside name description default gateway outside
name 10.4.11.1 description DefaultGW - Default Gateway inside Inside
!
interface GigabitEthernet0/0
nameif inside
security-level 100
IP 10.4.11.2 255.255.255.0
!
interface GigabitEthernet0/5
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/5.2000
VLAN 2000
nameif outside
security-level 0
IP 1.1.1.2 255.255.255.252
!
interface Management0/0
Shutdown
No nameif
no level of security
no ip address
management only
!
boot system Disk0: / asa861-2-smp - k8.bin
passive FTP mode
clock timezone BRST-3
clock summer-time recurring BRDT 2 Sun Oct 0:00 Sun Feb 3 0:00
DNS lookup field inside
DNS domain-lookup outside
DNS server-group DefaultDNS
1.1.1.1 server name
1.1.1.2 server name
domain xx.xx.xx.xx
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
network of the PoolAnyConnect object
subnet 10.6.4.0 255.255.252.0
access extensive list permits all ip a outside_in
list of access by standard tunnel allowed 10.0.0.0 255.0.0.0
pager lines 24
Enable logging
timestamp of the record
exploitation forest-size of the buffer 1048576
logging buffered information
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
mask 10.6.4.1 - 10.6.7.254 255.255.252.0 IP local pool PoolAnyConnect
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any inside
ICMP allow all outside
ASDM image disk0: / asdm - 66114.bin
enable ASDM history
ARP timeout 14400
NAT (inside, outside) static source any any static destination PoolAnyConnect PoolAnyConnect non-proxy-arp-search to itinerary
NAT (exterior, Interior) static source PoolAnyConnect PoolAnyConnect non-proxy-arp-search to itinerary
Access-group outside_in in external interface
Route outside 0.0.0.0 0.0.0.0 DefaultGW-outdoor 1
Route inside 10.0.0.0 255.0.0.0 DefaultGW-Inside 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
AAA-Server LDAP protocol ldap
AAA-server host 3.3.3.3 LDAP (inside)
Timeout 5
LDAP-base-dn o = xx
LDAP-scope subtree
LDAP-naming-attribute sAMAccountName
novell server type
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
AAA authentication enable LOCAL console
AAA authentication http LOCAL console
Enable http server
http 0.0.0.0 0.0.0.0 inside
http 2.2.2.2 255.255.255.240 outside
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 inside
SSH 2.2.2.2 255.255.255.240 outside
SSH timeout 10
Console timeout 10
management-access inside
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
SSL cipher aes128-sha1 aes256-3des-sha1 sha1
WebVPN
allow outside
AnyConnect essentials
AnyConnect image disk0:/anyconnect-win-3.1.03103-k9.pkg 1
AnyConnect enable
tunnel-group-list activate
internal GrpPolicyAnyConnect group strategy
attributes of Group Policy GrpPolicyAnyConnect
value of server DNS 1.1.1.1 1.1.1.2
VPN - 1000 simultaneous connections
client ssl-VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value in tunnel
field default value xx.xx.xx.xx
admin Dp4l7Cmqr7SMHl.l encrypted privilege 15 password username
tunnel-group AnyConnect type remote access
tunnel-group AnyConnect General attributes
address pool PoolAnyConnect
LDAP authentication group-server
Group Policy - by default-GrpPolicyAnyConnect
tunnel-group AnyConnect webvpn-attributes
enable AnyConnect group-alias
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
inspect the ctiqbe
inspect the http
inspect the dcerpc
inspect the dns
inspect the icmp
inspect the icmp error
inspect the they
inspect the amp-ipsec
inspect the mgcp
inspect the pptp
inspect the snmp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:9399e42e238b5824eebaa115c93ad924
: end
BTW, I changed the NAT configuration many attempts the problem, this is the current...
YPU need to allow your client VPN address pool (10.6.4.1 mask - 10.6.7.254 255.255.252.0) ssh and http from 'outside' access, which is where they come from. Add them to the:
http 0.0.0.0 0.0.0.0 inside
http 2.2.2.2 255.255.255.240 outside
SSH 0.0.0.0 0.0.0.0 inside
SSH 2.2.2.2 255.255.255.240 outside
Tags: Cisco Security
Similar Questions
-
Lock the AnyConnect VPN with broader access list
I'm trying to lock my AnyConnect VPN interface. I use the split tunneling. I want only to http tunnel traffic to an external http server we have and ftp to another external server behave. I don't want anything else through the tunnel or anywhere else allowed on our network. My current setup, I can connect to the vpn and the servers ping external ip address, but not by name. I can also not navigate anywhere else while I'm connected. It is not imperative for me to navigate anywhere else, when you are connected, but I need to allow only access specified above.
Configuration:
attributes Anyconnect-group policy
VPN-tunnel-Protocol svc webvpn
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list WebAccessVPN
WebVPN
list of URLS no
SVC request to enable default webvpn
WebAccessVPN list extended access allow icmp disable any newspaper host FTP - EXT object-group Ping_and_Trace
External FTP FTP access WebAccessVPN-list comment
WebAccessVPN list extended access permitted tcp disable no matter what newspaper to host FTP - EXT object-group DM_INLINE_TCP_2
WebAccessVPN list extended access allow icmp disable any newspaper host LICENSING-EXT object-group Ping_and_Trace
WebAccessVPN list extended access allowed object-group TCPUDP any LICENSING-EXT eq www log disable host
WebAccessVPN list extended access deny ip any object-group DM_INLINE_NETWORK_1
You can use the vpn filter under the attributes of political group. In the vpn-filter, you can reference the access list you created.
-
Cisco vpn client to connect but can not access to the internal network
Hi all
I have a VPN configured on cisco 5540. My vpn was working fine, but suddenly there is a question that the cisco vpn client to connect but can not access to the internal network
Any help would be much appreciated.
Hi Samir,
I suggest that you go to the ASA and check the configuration to make sure that it complies with the requirements according to the reference below link:
http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml
(The link above includes split tunneling, but this is just an option.
Please paste the output of "sh cry ipsec his" here so that we can check if phase 2 is properly trained. I would say as you go to IPSEC vpn client on your PC and check increment in packets sent and received in the window 'status '.
Let me know if this can help,
See you soon,.
Christian V
-
Hi team
Hope you do well. !!!
currently I am doing a project which consists in CISCO ASA-5545-X, RADIUS (domain controller) server for authentication. Here, I need to configure Anyconnect VPN and host checker in cisco asa.
1 users will connect: user advanced browser on SSL VPN pop past username and password.
2. (cisco ASA) authentication: VPN sends credentials to the RADIUS server.
3 RADIUS server: authentication: receipt and SSL VPN (ASA) group.
4 connectivity creation: If employee: PC so NAW verified compliance, no PC check Assign user to the appropriate role and give IP.
This is my requirement, so someone please guide me how to set up step by step.
1. how to set up the Radius Server?
2. how to configure CISCO ASA?
Thanks in advance.
Hey Chick,
Please consult the following page of installation as well as ASA Radius server. The ASA end there is frankly nothing much difference by doing this.
http://www.4salesbyself.com/1configuring-RADIUS-authentication-for-webvp...
Hope this helps
Knockaert
-
AnyConnect VPN users cannot access remote subnets?
I googled this until blue in the face without result. I don't understand why Cisco this so difficult? When clients connect to the anyconnect vpn, they can access the local subnet, but cannot access the resources in remote offices. What should I do to allow my anyconnect vpn clients access to my remote sites?
Cisco 5510 8.4
Hello
What are remote sites using as Internet gateway? Their default route here leads to the ASA or have their own Internet gateway? If they use this ASA for their Internet connection while they should already have a default route that leads traffic to the VPN to the pool, even if they had no specific route for the VPN itself pool. If they use their own local Internet gateway and the default route is not directed to this ASA then you would naturally have a route on the remote site (and anything in between) indicating the remote site where to join the pool of 10.10.224.0/24 VPN network.
In addition to routing, you must have configured for each remote site and the VPN pool NAT0
Just a simple example of NAT0 configuration for 4 networks behind the ASA and simple VPN field might look like this
object-group network to REMOTE SITES
object-network 10.10.10.0 255.255.255.0
object-network 10.10.20.0 255.255.255.0
object-network 10.10.30.0 255.255.255.0
object-network 10.10.40.0 255.255.255.0
network of the VPN-POOL object
10.10.224.0 subnet 255.255.255.0
NAT static destination DISTANCE-SITES SITES source (indoor, outdoor) REMOTE static VPN-VPN-POOL
The above of course assumes that the remote site are located behind the interface 'inside' (although some networks, MPLS) and naturally also the remote site networks are made for the sake of examples.
Since you are using Full Tunnel VPN should be no problem to the user VPN transfer traffic to this ASA in question.
My first things to check would be configuring NAT0 on the ASA and routing between remote sites and this ASA (regarding to reach the VPN pool, not the ASA network IP address)
Are you sure that the configuration above is related to this? Its my understanding that AnyConnect uses only IKEv2 and the foregoing is strictly defined for IKEv1?
-Jouni
-
Termination of the client PIX VPN and Internet access from the same interface
Hello
VPN remote users connect to PIX (7.2) outside interface, but need to have these clients to access the Internet through the PIX outside interface as well. Need this because PIX IPs is registered and allowed access to some electronic libraries. One way would be to set up a proxy within the network and vpn users have access to the Internet through the proxy, but can it be done without proxy?
Yes, public internet on a stick
-
I bought the kit the student creative cloud after the expiration of my first free month of the trial. Now I can not access all the apps.
Hi zackf49452714,
I'm sorry for the inconvenience caused.
Please follow the steps https://helpx.adobe.com/creative-cloud/help/sign-in-out-activate-apps.html
https://helpx.Adobe.com/x-productkb/policy-pricing/activate-deactivate-products.html
https://helpx.Adobe.com/x-productkb/policy-pricing/activation-network-issues.html
Let us know if this helps!
-
ASA Anyconnect VPN do not work or download the VPN client
I have a Cisco ASA 5505 that I try to configure anyconnect VPN and thought, I've changed my setup several times but trying to access my static public IP address of the external IP address to download the image, I am not able to. Also when I do a package tracer I see he has been ignored through the acl when the packets from side to the ASA via port 443, it drops because of the ACL. My DMZ so will he look like something trying to access the ASA via the VPN's going to port 443. Here is my config
XXXX # sh run
: Saved
:
ASA Version 8.4 (3)
!
hostname XXXX
search for domain name
activate pFTzVNrKdD9x5rhT encrypted password
zPBAmb8krxlXh.CH encrypted passwd
names of
!
interface Ethernet0/0
Outside-interface description
switchport access vlan 20
!
interface Ethernet0/1
Uplink DMZ description
switchport access vlan 30
!
interface Ethernet0/2
switchport access vlan 10
!
interface Ethernet0/3
switchport access vlan 10
!
interface Ethernet0/4
Ganymede + ID description
switchport access vlan 10
switchport monitor Ethernet0/0
!
interface Ethernet0/5
switchport access vlan 10
!
interface Ethernet0/6
switchport access vlan 10
!
interface Ethernet0/7
Description Wireless_AP_Loft
switchport access vlan 10
!
interface Vlan10
nameif inside
security-level 100
IP 192.168.10.1 255.255.255.0
!
interface Vlan20
nameif outside
security-level 0
IP address x.x.x.249 255.255.255.248
!
Vlan30 interface
no interface before Vlan10
nameif dmz
security-level 50
IP 172.16.30.1 255.255.255.0
!
boot system Disk0: / asa843 - k8.bin
passive FTP mode
DNS lookup field inside
DNS domain-lookup outside
DNS domain-lookup dmz
DNS server-group DefaultDNS
Name-Server 8.8.8.8
Server name 8.8.4.4
search for domain name
network obj_any1 object
subnet 0.0.0.0 0.0.0.0
network of the Webserver_DMZ object
Home 172.16.30.8
network of the Mailserver_DMZ object
Home 172.16.30.7
the object DMZ network
172.16.30.0 subnet 255.255.255.0
network of the FTPserver_DMZ object
Home 172.16.30.9
network of the Public-IP-subnet object
subnet x.x.x.248 255.255.255.248
network of the FTPserver object
Home 172.16.30.8
network of the object inside
192.168.10.0 subnet 255.255.255.0
network of the VPN_SSL object
10.101.4.0 subnet 255.255.255.0
outside_in list extended access permit tcp any newspaper object Mailserver_DMZ eq www
outside_in list extended access permit tcp any newspaper EQ 587 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper SMTP object Mailserver_DMZ eq
outside_in list extended access permit tcp any newspaper of the Mailserver_DMZ eq pop3 object
outside_in list extended access permit tcp any newspaper EQ 2525 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper of the Mailserver_DMZ eq imap4 object
outside_in list extended access permit tcp any newspaper EQ 465 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper EQ 993 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper EQ 995 object Mailserver_DMZ
outside_in list extended access permit tcp any newspaper EQ 5901 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper Mailserver_DMZ eq https object
Note access list ACL for VPN Tunnel from Split vpn_SplitTunnel
vpn_SplitTunnel list standard access allowed 192.168.10.0 255.255.255.0
pager lines 24
Enable logging
timestamp of the record
exploitation forest-size of the buffer to 8192
logging trap warnings
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
MTU 1500 dmz
local pool VPN_SSL 10.101.4.1 - 10.101.4.4 255.255.255.0 IP mask
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 647.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside, outside) static source inside inside static destination VPN_SSL VPN_SSL
NAT (exterior, Interior) static source VPN_SSL VPN_SSL
!
network obj_any1 object
NAT static interface (indoor, outdoor)
network of the Webserver_DMZ object
NAT (dmz, outside) static x.x.x.250
network of the Mailserver_DMZ object
NAT (dmz, outside) static x.x.x.. 251
the object DMZ network
NAT (dmz, outside) static interface
Access-group outside_in in external interface
Route outside 0.0.0.0 0.0.0.0 x.x.x.254 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
AAA-server protocol Ganymede HNIC +.
AAA-server host 192.168.10.2 HNIC (inside)
Timeout 60
key *.
identity of the user by default-domain LOCAL
Console HTTP authentication AAA HNIC
AAA console HNIC ssh authentication
Console AAA authentication telnet HNIC
AAA authentication secure-http-client
http 192.168.10.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ca trustpoint localtrust
registration auto
Configure CRL
Crypto ca trustpoint VPN_Articulate2day
registration auto
name of the object CN = vpn.articulate2day.com
sslvpnkey key pair
Configure CRL
Telnet 192.168.10.0 255.255.255.0 inside
Telnet timeout 30
SSH 192.168.10.0 255.255.255.0 inside
SSH timeout 15
SSH version 2
Console timeout 0
No vpn-addr-assign aaaDHCP-client update dns
dhcpd dns 8.8.8.8 8.8.4.4
dhcpd outside auto_config
!
dhcpd address 192.168.10.100 - 192.168.10.150 inside
dhcpd allow inside
!
dhcpd address dmz 172.16.30.20 - 172.16.30.23
dhcpd enable dmz
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
authenticate the NTP
NTP server 192.168.10.2
WebVPN
allow outside
AnyConnect image disk0:/anyconnect-linux-64-3.1.06079-k9.pkg 1
AnyConnect enable
tunnel-group-list activate
internal VPN_SSL group policy
VPN_SSL group policy attributes
value of server DNS 8.8.8.8
client ssl-VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list vpn_SplitTunnel
the address value VPN_SSL pools
WebVPN
activate AnyConnect ssl dtls
AnyConnect Dungeon-Installer installed
AnyConnect ssl keepalive 15
AnyConnect ssl deflate compression
AnyConnect ask enable
ronmitch50 spn1SehCw8TvCzu7 encrypted password username
username ronmitch50 attributes
type of remote access service
type tunnel-group VPN_SSL_Clients remote access
attributes global-tunnel-group VPN_SSL_Clients
address VPN_SSL pool
Group Policy - by default-VPN_SSL
tunnel-group VPN_SSL_Clients webvpn-attributes
enable VPNSSL_GNS3 group-alias
type tunnel-group VPN_SSL remote access
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect esmtp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:d41d8cd98f00b204e9800998ecf8427e
: endXXXX #.
You do not have this configuration:
object network DMZ nat (dmz,outside) static interface
Try and take (or delete):
object network DMZ nat (dmz,outside) dynamic interface
-
ASA 5505 VPN established, cannot access inside the network
Hi, I recently got an ASA 5505, and I spent weeks to find a way to set up a VPN on it.
After a few days, I finally found the solution to connect to my ASA with a VPN client yet and cannot access devices that are connected to the ASA.
Here is my config:
ASA Version 8.2 (5)
!
hostname asa01
domain kevinasa01.net
activate 8Ry2YjIyt7RRXU24 encrypted password
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
switchport access vlan 5
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address dhcp setroute
!
interface Vlan5
No nameif
security-level 50
IP 172.16.1.1 255.255.255.0
!
passive FTP mode
DNS server-group DefaultDNS
domain kevinasa01.net
permit same-security-traffic intra-interface
Remote_Kevin_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.254.0 255.255.255.240
inside_nat0_outbound list of allowed ip extended access all 192.168.254.0 255.255.255.0
inside_nat0_outbound list of allowed ip extended access entire 192.168.1.0 255.255.255.0
sheep - in extended Access-list allow IP 192.168.254.0 255.255.255.0 192.168.1.0 255.255.255.0
access extensive list ip 192.168.254.0 outside_access_in allow 255.255.255.0 any
access extensive list ip 192.168.254.0 inside_access_in allow 255.255.255.0 any
pager lines 24
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
pool pool 192.168.254.1 - 192.168.254.10 255.255.255.0 IP mask
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (outside) 1 192.168.254.0 255.255.255.0
NAT (inside) 0 access-list sheep - in
NAT (inside) 1 192.168.1.0 255.255.255.0
NAT (inside) 1 0.0.0.0 0.0.0.0
Access-group outside_access_in in interface outside
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
management-access inside
dhcpd outside auto_config
!
dhcpd address 192.168.1.5 - 192.168.1.36 inside
dhcpd allow inside
!a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal Remote_Kevin group strategy
attributes of Group Policy Remote_Kevin
value of server DNS 192.168.1.12 192.168.1.13
VPN - connections 3
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list Remote_Kevin_splitTunnelAcl
kevinasa01.NET value by default-field
username kevin mz6JxJib/sQqvsw9 password encrypted privilege 0
username kevin attributes
VPN-group-policy Remote_Kevin
type tunnel-group Remote_Kevin remote access
attributes global-tunnel-group Remote_Kevin
address-pool
Group Policy - by default-Remote_Kevin
IPSec-attributes tunnel-group Remote_Kevin
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
inspect the icmp error
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:2bb1da52d1993eb9b13c2f6dc97c16cd
: endThank you
Hello
I read your message quickly through my cell phone. I don't know why you have spent your config twice. Maybe a typo issue.
I see the acl sheep in the wrong way. I mean 192.168.254 are your pool VPN and 192.168.1.0 your local LAN.
The acl must be:
sheep - in extended access-list permit ip 192.168.1.0 255.255.255.0 192.168.254.0 255.255.255.0
For nat (inside), you have 2 lines:
NAT (inside) 1 192.168.1.0 255.255.255.0 ==> it is redundant as the 1 below does the same thing with more networks if there is inside side. You can delete it.
NAT (inside) 1 0.0.0.0 0.0.0.0Why are you doing this nat (outside)?
NAT (outside) 1 192.168.254.0 255.255.255.0
Here are the first questions that I have seen by reading through my mobile. Let's change this and let me know. I'll take a look later with a computer (tonight or tomorrow)
Thank you.
PS: Please do not forget to rate and score as good response if this solves your problem.
-
Configuration of the Cisco ACS 5.3 AnyConnect VPN and management of a Cisco ASA 5500.
We have configured a Cisco ASA 5505 as a VPN endpoint for one of our user groups. It works, but it works too well.
We have a group called XXX we need to have access to the Cisco AnyConnect Client. We have selected this group of our Active Directory and added to our ACS configuration. We've also added a group called YYY that will manage the ASA. However, this group has no need to access the VPN.
We added XXX movies for the elements of the policy of access to the network-> authorization profiles. We also have a profile of YYY.
She continues to knock on our default Service rule that says allow all.
We have also created a default network access rule. for this.
I am at a loss. I'm sure I missed a checkbox or something.
Any help would be really appreciated.
Dwane
We use Protocol Management GANYMEDE ASA and Ray for VPN access?
For administration, you must change the device by default admin access strategy and create a permission policy. Even by the way, you can change the network access by default for vpn access and create a respective policy for that too.
On the SAA, you must configure Ganymede and Ray both as a server group.
For the administration, you can set Ganymede as an external authentication under orders aaa Server
AAA-server protocol Ganymede GANYMEDE +.
Console HTTP authentication AAA GANYMEDE
Console Telnet AAA authentication RADIUS LOCAL
authentication AAA ssh console LOCAL GANYMEDE
Console to enable AAA authentication RADIUS LOCAL
For VPN, you must set the authentication radius under the tunnel-group.
I hope this helps.
Kind regards
Jousset
The rate of useful messages-
-
Ipad Cisco ipsec VPN connects but not access to the local network
Hi guys,.
I am trying to connect our ipads to vpn to access network resources. IPSec cisco ipad connects but not lan access and cannot ping anything not even not the interfaces of the router.
If I configure the vpn from cisco on a laptop, it works perfectly, I can ping all and can access resources on the local network if my guess is that the traffic is not going in the tunnel vpn between ipad and desktop.
Cisco 877.
My config is attached.
Any ideas?
Thank you
Build-in iPad-client is not useful to your configuration.
You have three options:
(1) remove the ACL of your vpn group. Without split tunneling client will work.
2) migrate legacy config crypto-map style. Here, you can use split tunneling
3) migrate AnyConnect.
The root of the problem is that the iPad Gets the split tunneling-information. But instead of control with routing traffic should pass through the window / the tunnel and which traffic is allowed without the VPN of the iPad tries to build a set of SAs for each line in your split-tunnel-ACL. But with the model-virtual, SA only is allowed.
-
When remote users to connect to the Cisco ASA VPN and authenticate with Cisco AnyConnect client, they then full access to the environment internal of LAN of business as if they were sitting at their desks in the Office of the Corporation.
Right?
After that the remote client authenticates to the AnyConnect VPN, it is sensible to then run remote users of traffic through the corporate firewall (outside to inside) before allowing LAN access full corporate?
Remote_User - vpn - ANYCONNECT-(outside) (inside) firewall - CORP_LAN
Thank you
Frank
Hello
Yes, by default, all traffic will be sent through the tunnel.
If there are users VPN shouldn't be able to reach the resources, you need to establish rules for access to it. The best way to do this is by using VPN filter.
-
Enable WebVPN without granting access to the ASA/AMPS/CLI
Is there a way to allow access to users WebVPN (SSL) through the ASA (8.2.1) without allowing them to connect via ASDM, SSH, Telnet or CLI? I want to warn my VPN users to access the configuration of the firewall.
I see in ASDM there are certain formulations on "it's effective only if AAA authenticates command console is configured" but I do not understand what it is explained.
Thanks in advance,
Greg
You can restrict local users with the following:
name of user attributes
type of remote access service
You need aaa authenticate console orders because when its not defined you can come as the default username (pix) or no username at all and the password enable (in the case of Deputy Ministers DEPUTIES). If there is no sent username, so we cannot verify obviously not the option of type 'service' in the attributes of user name. Here is more information on the command "aaa authenticate console":
http://www.Cisco.com/en/us/docs/security/ASA/asa80/command/reference/A1.html#wp1535834
-heather
-
Cisco Anyconnect VPN does not work in windows 7 64 bit
Hello
I found that the cisco anyconnect (version 3, any series) does not work in windows 7 (64-bit).
The vpn is connected, but there is not any internet access.I tried to solve the problems of:
-Disabling the firewall.
-disable the anti-virus etc.
But while I tried using with 32 bit, it works very well.
Also, I found that there is not a specific version of anyconnect vpn for only 64-bit.
Do any body have the idea how to solve this problem, either it's a bug of cisco vpn itself?
Certainly, you just need to install a later version of AnyConnect. You need a Cisco, for example a SmartNet maintenance contract, to download the new versions.
-
VPN is not talk for the subnet behind a remote router
Hi all
I was hitting my head on the wall for a few days everything that is wrong with my configuration ASA...
That's what I got:
AnyConnect vpn (10.10.70.0/24)-online tunnel => ASA5505 performer v9.1.2 (10.10.20.1)-online (10.10.20.2) router (10.10.50.1) 1841-online my environment tour (10.10.50.0/24)
VPN is allowed to authenticate, get an address, ping 10.10.20.0/24 but unable to pass traffic (ping, ftp, etc.) 10.10.50.0 network at all.
Using EIGRP between ASA and 1841, tried static set time 'network' then 'redisturbute' and the ' redisturbute static route-map ", still no luck.
Found several docs, tried, doesn't seem to help...
https://supportforums.Cisco.com/thread/2206416
http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00809d07de.shtml
Help, please...
Attach the configs for the ASA and router
Thank you in advance!
Keith S.
Hi Keith,
You are using IKEv1 or IKEV2.
It comes to your configuration:
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
Crypto-map dynamic outside_dyn_map 20 set transform-set ESP-3DES-SHA ikev1
Crypto-map dynamic outside_dyn_map 20 the value reverse-road
test of dynamic-map 10 crypto-card, the value reverse-road
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
The dynamic map that is applied to the interface is SYSTEM_DEFAULT_CRYPTO_MAP which is an ikev2.
But the question is not the one. Depending on your configuration, there is a runnning between the ASA and the router EIGRP and according to your router table routing does not know where is 10.10.70.0/24 subnet is. To inject the subnet pool VPN in the routing table that we need an arriere-route control that you configured on a card which is not in use. Try this:
Crypto than dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 Road opposite value.
And let me know if it helps.
Thank you
Jeet Kumar
Maybe you are looking for
-
I do not have a firefox button and didn't get to the general page
I have firefox symbol in the upper left corner, but I don't have a button that takes me to the general page. Do I need a button, and if not how to access the General page? If I need a button how to do it
-
HP envy 15-j104sl: display not working not properly
Hello I have a Hp Envy 15-j104sl, unfortunately after a fall, the screen does not work properly: sometimes, the left part or the entire display turns white and it is impossible to use it unless I move the screen / hinges in another post.The glass is
-
How do remove you a bug on ipad
I get a message (even though I'm on Safari), telling me that I won a free iPad and click OK. It is not possible out of the screen unless you click OK, and I'm not willing to do. I turned off the iPad for 2 days and he is still on the screen of Safa
-
What happened to my setting of brightness on my desk?
I have a desktop of windows 7 and I tried to adjust the brightness, but the cursor left. A lot of people have this problem with their laptop and I could not find something which does not disappear?