ASA 5520 customize logo in vpn without customer portal

Similar Questions

• ASA 5520 to Juniper ss505m vpn

  I'm having a problem with the vpn site to site between a asa 5520 and Juniper ss 505 m. The tunnel rises, but we seem unable to pass traffic through the vpn tunnel.  It appears on the remote side makes a connection to the ftp server on the Local Server, but is never prompt identification of connection information.

  April 19, 2016 13:27:13 SQL-B2B-01: % ASA-4-402116: IPSEC: received a package ESP x.x (SPI = 0xD167A5E8, sequence number = 0xD).

  241.90 (user = X.X.241.90) at X.X.167.230.  Inside the package décapsulés does not match policy negotiated in the SA.  The

  package specifies its destination as its Protocol TCP, its source such as X.X.2.68 and X.X.167.233.  SA specifies its loc

  proxy of Al X.X.167.233/255.255.255.255/tcp/5376 and his remote_proxy as X.X.2.68/255.255.255.255/tcp/5376.

  list of remote ip-group of objects allowed extended West Local Group object

  NAT static Local_Pub Local destination (indoor, outdoor) static source Remote

  Crypto ipsec ikev1 transform-set esp-aes-256 Remote esp-sha-hmac

  West-map 95 crypto card is the Remote address
  card crypto West-map 95 set peer X.X.241.90
  map West-map 95 set transform-set Remote ikev1 crypto
  card crypto West-map 95 defined security-association life seconds 28800

  Juniper-

  "Remote-ftp" X.X.167.233 255.255.255.255

  Gateway proposal P1 preshare "[email protected]/ * /" proposal "pre-g2-aes256-sha-28800.

  P2-proposal "no-pfs-esp-aes256-sha-28800" No. - pfs esp aes256 sha-1 second 28800

  ----------------------

  the top of the policy of "Trust" to "Untrust" "X.X.2.68/32" "Remote-ftp' 'ftp' vpn"Remote-vpn"tunnel log

  put on top of the "Untrust" policy to the "Trust" "Remote-ftp' 'X.X.2.68/32' 'ftp' vpn"SonoraQ-vpn"tunnel sign

  I do not know Juniper, but it seems that it is trying to negotiate the use of only 5376/tcp on the tunnel, when it should be negotiated just Protocol "ip".

• Cisco ASA 5520 cannot ping between VPN Tunnels

  I have the main site and sites A and B.  A to connect to the hand and B connects to the main.  I can ping from A hand and has for main.  I can ping from main to B and B to main.  However, I can not ping from A to B.  A and B are sonicwall 2040 and main is a 5520.  The question should not be with the 5520 none allowing traffic between the two VPN Tunnels, but I can't understand why it does not work.  Can someone give an idea on that?  Thanks in advance.

  Hello

  I see that you use ASDM. Always makes my eyes bleed when I need to look at the DM_INLINE of named objects and try to make sense the CLI format

  Seems to me that there are problems with the NAT.

  If you don't mind a small break between the main Site and remote locations, I'd say changing some follows the NAT configuration

  Remove old

  no nat source (indoor, outdoor) public static DM_INLINE_NETWORK_9 DM_INLINE_NETWORK_9 DM_INLINE_NETWORK_10 DM_INLINE_NETWORK_10 non-proxy-arp-search of route static destination

  no nat source (indoor, outdoor) public static DM_INLINE_NETWORK_11 DM_INLINE_NETWORK_11 DM_INLINE_NETWORK_12 DM_INLINE_NETWORK_12 non-proxy-arp-search of route static destination

  Add a new

  object-group network NETWORK-2790

  object-network 10.217.0.0 255.255.255.0

  object-network 10.217.1.0 255.255.255.0

  object-group network NETWORK-3820

  object-network 10.216.0.0 255.255.255.0

  object-network 10.216.1.0 255.255.255.0

  object-group network NETWORK-COLO

  object-net 10.8.0.0 255.255.255.0

  destination of NETWORK of NETWORK-2790-2790 static NAT (outside, outside) static source NETWORK - 3820 - 3820

  NAT static destination of NETWORK of NETWORK-COLO-COLO (indoor, outdoor) static source NETWORK - 2790 - 2790

  NAT static destination of NETWORK of NETWORK-COLO-COLO (indoor, outdoor) static source NETWORK - 3820 - 3820

  The first new line of configuring NAT manages the NAT0 configuration for traffic between SiteA and SiteB. The following configurations of NAT 2 manage the NAT0 for traffic between the main Site - hand Site SiteA - SiteB

  -Jouni

• What VPN work as a PPTP vpn firewall CISCO-ASA-5520.

  Hi all

  Can you please tell me which replace the VPN I can configure PPTP on ASA 5520 firewall. What VPN work as a PPTP vpn firewall CISCO-ASA-5520.

  You can use the wizard VPN of RA with ASDM and confiugre L2TP IPSEC VPN that does not need a VPN Client must be installed.

  Michael

  Please note all useful posts

• SSL VPN without disabled in ASA5505 after the Activation of the AnyConnect client

  Hello everyone,

  I am facing a problem with the VPN service in ASA 5505. Initially, I was using SSL VPN without customer who was working absolutely fine, no problem. Recently I bought AnyConnect Essentials License with license AnyConnect VPN, Mobile (for focusing on the Client SSL VPN Service for desktop and mobile respectively) and have activated these keys inside of the firewall. After that I may be able to connect to based on the VPN Client, using the AnyConnect client. Clientless VPN access is not allowing you to connect and displays an error (see the attached screenshot).

  I created two VPN profiles Viz, basic (for clientless VPN) and rvsvpn (for client based VPN). Download the AnyConnect Client I can connect to the rvsvpn profile. But if I try to connect using the basic profile, it throws an error has been to what is displayed in the exhibition.

  Please help me in this regard, as what can be done to use both the vpn connection profile. Or what the use of AnyConnect disables client access?

  Waiting for your help.

  Thanks in advance.

  Samrat.

  "Anyconnect essentials" in your configuration command to disable all profiles without customer (as well as other features that require the Premium license).

  Essentials and Premium are mutually exclusive as the performance of duties. You can have both installed licenses, but only use one or the other (and never both at once) in your running configuration.

• IPSec VPN to asa 5520

  Hello

  First I must admit that I am not very versed in Cisco equipment or in general IPSEC connections so my apologies if I'm doing something really good obviously stupid, but I checked through any kind of things that I could find on the internet on the configuration of IPSEC VPN.

  The setup I have is an asa 5520 (o/s 8.2) firewall which, for now, is connected to a temporary connection beautiful style home broadband for testing purposes. The netopia router is configured to allow ipsec passthrough and redirect 62515 UDP, TCP 10000, 4500 UDP, UDP 500 ports in the asa 5520.

  I'm trying to connein out of a laptop with disabled windows firewall and vpn cisco 5.0.02.0090 client version.

  I ran several attempts through the ipsec configuration wizard options. most of the time that nothing comes in the newspaper to show that a connection was attempted, but there is a way I can set up product options the following on the firewall log:

  4. Sep 24 2010 | 13: 54:29 | 713903 | Group = VPNtest9, IP = 86.44.x.x, error: cannot delete PeerTblEntry

  5: Sep 24 2010 | 13: 54:29 | 713902 | Group = VPNtest9, IP = 86.44.x.x, drop table homologous counterpart does not, no match!

  6. Sep 24 2010 | 13: 54:21 | 713905 | Group VPNtest9, IP = 86.44.x.x, P1 = relay msg sent to AM WSF

  3: Sep 24 2010 | 13: 54:21 | 713201 | Group = VPNtest9, IP = 86.44.x.x, double-Phase 1 detected package. Retransmit the last packet.

  6. Sep 24 2010 | 13: 54:16 | 713905 | Group VPNtest9, IP = 86.44.x.x, P1 = relay msg sent to AM WSF

  3: Sep 24 2010 | 13: 54:16 | 713201 | Group = VPNtest9, IP = 86.44.x.x, double-Phase 1 detected package. Retransmit the last packet.

  6. Sep 24 2010 | 13: 54:11 | 713905 | Group VPNtest9, IP = 86.44.x.x, P1 = relay msg sent to AM WSF

  3: Sep 24 2010 | 13: 54:11 | 713201 | Group = VPNtest9, IP = 86.44.x.x, double-Phase 1 detected package. Retransmit the last packet.

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  3: Sep 24 2010 | 13: 54:06 | 713257 | 1 failure to phase: incompatibility of types of attributes of class Group Description: RRs would be: Group 2 FCMS would: Group 1

  6. Sep 24 2010 | 13: 54:06 | 302015 | 86.44.x.x | 51905 | 192.168.0.27 | 500 | Built UDP inbound connection 7487 for Internet:86.44.x.x/51905 (86.44.x.x/51905) at identity:192.168.0.27/500 (192.168.0.27/500)

  and this, in the journal of customer:

  Cisco Systems VPN Client Version 5.0.02.0090

  Copyright (C) 1998-2007 Cisco Systems, Inc.. All rights reserved.

  Customer type: Windows, Windows NT

  Running: 5.1.2600 Service Pack 3

  24 13:54:08.250 24/09/10 Sev = Info/4 CM / 0 x 63100002

  Start the login process

  25 13:54:08.265 24/09/10 Sev = Info/4 CM / 0 x 63100004

  Establish a secure connection

  26 13:54:08.265 24/09/10 Sev = Info/4 CM / 0 x 63100024

  Attempt to connect with the server "213.94.x.x".

  27 13:54:08.437 24/09/10 Sev = Info/6 IKE/0x6300003B

  Attempts to establish a connection with 213.94.x.x.

  28 13:54:08.437 24/09/10 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Frag), VID(Nat-T), VID (Unity)) at 213.94.x.x

  29 13:54:08.484 24/09/10 Sev = Info/4 IPSEC / 0 x 63700008

  IPSec driver started successfully

  30 13:54:08.484 24/09/10 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  31 13:54:13.484 24/09/10 Sev = Info/4 IKE / 0 x 63000021

  Retransmit the last package!

  32 13:54:13.484 24/09/10 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (Retransmission) to 213.94.x.x

  33 13:54:18.484 24/09/10 Sev = Info/4 IKE / 0 x 63000021

  Retransmit the last package!

  34 13:54:18.484 24/09/10 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (Retransmission) to 213.94.x.x

  35 13:54:23.484 24/09/10 Sev = Info/4 IKE / 0 x 63000021

  Retransmit the last package!

  36 13:54:23.484 24/09/10 Sev = Info/4 IKE / 0 x 63000013

  SEND to > ISAKMP OAK AG (Retransmission) to 213.94.x.x

  37 13:54:28.484 24/09/10 Sev = Info/4 IKE / 0 x 63000017

  Marking of IKE SA delete (I_Cookie = 36C50ACCE984B0B0 R_Cookie = 0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING

  38 13:54:28.984 24/09/10 Sev = Info/4 IKE/0x6300004B

  IKE negotiation to throw HIS (I_Cookie = 36C50ACCE984B0B0 R_Cookie = 0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING

  39 13:54:28.984 24/09/10 Sev = Info/4 CM / 0 x 63100014

  Could not establish the Phase 1 SA with the server '213.94.x.x' due to the 'DEL_REASON_PEER_NOT_RESPONDING '.

  40 13:54:28.984 24/09/10 Sev = Info/5 CM / 0 x 63100025

  Initializing CVPNDrv

  41 13:54:28.984 24/09/10 Sev = Info/6 CM / 0 x 63100046

  Set indicator established tunnel to register to 0.

  42 13:54:28.984 24/09/10 Sev = Info/4 IKE / 0 x 63000001

  Signal received IKE to complete the VPN connection

  43 13:54:29.187 24/09/10 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  44 13:54:29.187 24/09/10 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  45 13:54:29.187 24/09/10 Sev = Info/4 IPSEC / 0 x 63700014

  Remove all keys

  46 13:54:29.187 24/09/10 Sev = Info/4 IPSEC/0x6370000A

  IPSec driver successfully stopped

  I have connectivity full http from the internet to a machine inside the asa 5520 so I think that the static routing and NAT'ing should be ok, but I am pleased to provide you with all the details.

  Can you see what I'm doing wrong?

  Thank you

  Sam

  Pls add the following policy:

  crypto ISAKMP policy 10

  preshared authentication

  the Encryption

  md5 hash

  Group 2

  You can also run debug on the ASA:

  debugging cry isa

  debugging ipsec cry

  and retrieve debug output after trying to connect.

• VPN site to site & outdoor on ASA 5520 VPN client

  Hi, I'm jonathan rivero.

  I have an ASA 5520 Version 8.0 (2), I configured the site-to-site VPN and works very well, in the other device, I configured the VPN Client for remote users and works very well, but I try to cofigure 2 VPNs on ASA 5520 on the same outside interface and I have the line "outside_map interface card crypto outdoors (for VPN client). , but when I set up the "crypto map VPNL2L outside interface, it replaces the command', and so I can have only a single connection.

  the executed show.

  ASA1 (config) # sh run

  : Saved

  :

  ASA Version 8.0 (2)

  !

  hostname ASA1

  activate 7esAUjZmKQSFDCZX encrypted password

  names of

  !

  interface Ethernet0/0

  nameif inside

  security-level 100

  address 172.16.3.2 IP 255.255.255.0

  !

  interface Ethernet0/1

  nameif outside

  security-level 0

  IP 200.20.20.1 255.255.255.0

  !

  interface Ethernet0/1.1

  VLAN 1

  nameif outside1

  security-level 0

  no ip address

  !

  interface Ethernet0/2

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Ethernet0/3

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Ethernet0/4

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  interface Ethernet0/5

  Shutdown

  No nameif

  no level of security

  no ip address

  !

  2KFQnbNIdI.2KYOU encrypted passwd

  passive FTP mode

  object-group, net-LAN

  object-network 172.16.0.0 255.255.255.0

  object-network 172.16.1.0 255.255.255.0

  object-network 172.16.2.0 255.255.255.0

  object-network 172.16.3.0 255.255.255.0

  object-group, NET / remote

  object-network 172.16.100.0 255.255.255.0

  object-network 172.16.101.0 255.255.255.0

  object-network 172.16.102.0 255.255.255.0

  object-network 172.16.103.0 255.255.255.0

  object-group network net-poolvpn

  object-network 192.168.11.0 255.255.255.0

  access list outside nat extended permit ip net local group object all

  access-list extended sheep allowed ip local object-group net object-group net / remote

  access-list extended sheep allowed ip local object-group net net poolvpn object-group

  access-list splittun-vpngroup1 extended permitted ip local object-group net net poolvpn object-group

  pager lines 24

  Within 1500 MTU

  Outside 1500 MTU

  outside1 MTU 1500

  IP local pool ippool 192.168.11.1 - 192.168.11.100 mask 255.255.255.0

  no failover

  ICMP unreachable rate-limit 100 burst-size 10

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0 access-list sheep

  NAT (inside) 1 access list outside nat

  Route outside 0.0.0.0 0.0.0.0 200.20.20.1 1

  Route inside 172.16.0.0 255.255.255.0 172.16.3.2 1

  Route inside 172.16.1.0 255.255.255.0 172.16.3.2 1

  Route inside 172.16.2.0 255.255.255.0 172.16.3.2 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout, uauth 0:05:00 absolute

  dynamic-access-policy-registration DfltAccessPolicy

  the ssh LOCAL console AAA authentication

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  86400 seconds, duration of life crypto ipsec security association

  Crypto ipsec kilobytes of life security-association 400000

  Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA

  card crypto VPNL2L 1 match for sheep

  card crypto VPNL2L 1 set peer 200.30.30.1

  VPNL2L 1 transform-set ESP-3DES-MD5 crypto card game

  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

  outside_map interface card crypto outside

  crypto isakmp identity address

  crypto ISAKMP allow outside

  crypto ISAKMP policy 20

  preshared authentication

  3des encryption

  md5 hash

  Group 2

  life 86400

  crypto ISAKMP policy 30

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  crypto ISAKMP policy 65535

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  a basic threat threat detection

  Statistics-list of access threat detection

  !

  !

  internal vpngroup1 group policy

  attributes of the strategy of group vpngroup1

  banner value +++ welcome to Cisco Systems 7.0. +++

  value of 192.168.0.1 DNS server 192.168.1.1

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value splittun-vpngroup1

  value by default-ad domain - domain.local

  Split-dns value ad - domain.local

  the address value ippool pools

  username password asa1 VRTlLlJ48/PoDKjS encrypted privilege 15

  tunnel-group 200.30.30.1 type ipsec-l2l

  IPSec-attributes tunnel-group 200.30.30.1

  pre-shared-key *.

  type tunnel-group vpngroup1 remote access

  tunnel-group vpngroup1 General-attributes

  ippool address pool

  Group Policy - by default-vpngroup1

  vpngroup1 group of tunnel ipsec-attributes

  pre-shared-key *.

  context of prompt hostname

  Cryptochecksum:00000000000000000000000000000000

  : end

  ASA2 (config) #sh run

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  86400 seconds, duration of life crypto ipsec security association
  Crypto ipsec kilobytes of life security-association 400000
  card crypto VPNL2L 1 match for sheep
  card crypto VPNL2L 1 set peer 200.30.30.1
  VPNL2L 1 transform-set ESP-3DES-MD5 crypto card game
  VPNL2L interface card crypto outside
  crypto isakmp identity address
  crypto ISAKMP allow outside
  crypto ISAKMP policy 20
  preshared authentication
  3des encryption
  md5 hash
  Group 2
  life 86400

  tunnel-group 200.30.30.1 type ipsec-l2l
  IPSec-attributes tunnel-group 200.30.30.1
  pre-shared key cisco

  my topology:

  

  I try with the following links, but did not work

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080912cfd.shtml

  http://www.Cisco.com/en/us/products/ps6120/products_tech_note09186a00807e0aca.shtml

  Best regards...

  "" I thing both the force of the SAA with the new road outside, why is that? ".

  without the road ASA pushes traffic inward, by default.

  In any case, this must have been a learning experience.

  Hopefully, this has been no help.

  Please rate, all the helful post.

  Thank you

  Rizwan Muhammed.

• SSL VPN without client customization

  Hi all

  I'm learning to clientless SSL on ASA 5520 VPN customization, but I can't seem to add a few.

  y at - it a command or a sine qua non before customization? It could be question of java or asdm?

  ciscoasa # sh ve

  Cisco Adaptive Security Appliance Software Version 8.4 (2)

  Device Version 7.0 Manager (1)

  

  "AnyConnect Premium peers: 2 perpetual" is the key bit there. Those are the two included AnyConnect Premium counterparts with the ASAs.

  The VPN peers 'Other' and 'Total' to take into account the fact that you have also up to 10 IPsec VPN (remote access) or site to site over the two remote access client VPN active one any time.

  In general a remote VPN access can be:

  a. clientless SSL (only a browser required by the counterpart, but requires confusedly, AnyConnect Premium license on the SAA),.

  b. full-tunnel SSL (launch browser or directly from the Anyconnect client, requires either AnyConnect Premium or Essentials on the SAA), or

  c. based on IPsec (using the Cisco's IPsec client inherited with IKEv1 (no AnyConnect license required) or 3.0 AnyConnect client or later (with Essentials or Premium license on the SAA) with IKEv2).

  And there will be a test on this.

• SSL VPN using ASA 5520 mode cluster - several problems

  I configured 2 ASA 5520 s in the load balancing cluster mode. I connect using anyconnect and I download the customer the first time and everything works well except outlook. I don't know why outlook does not work.

  The second problem is after the anyconnect client is installed on your machine, he remembers that ASA (say ASA2) he first connected and the GUI shows the address IP of ASA2 instead of the virtual IP address of the cluster. I want users always connect using the virtual IP address.

  The third problem I have is there is a default group of SSL VPN and I want all users to use this group. In the initial web page, there is a drop down menu which shows that this group, but I still want to disable this menu drop-down.

  Any suggestions?

  To disable the drop-down menu, you can turn it off with the command

  WebVPN

  no activation of tunnel-group-list

  This will take care of your last issue.

  ***************************

  You can create a profile of the Anyconnect client with the name of the server you want to connect with and that make the ASA that will solve your problem of virtual IP.

  **************************

  Regarding Outlook, do you use specific ports which allows inspection of the ASA. Take a look at the list of inspection on the SAA and perhaps try to disable inspection and see if it works.

  *****************************

• Using Cisco Client to site VPN on a behind a NAT ASA 5520

  I apologize if this has been asked and we answered in the forums.  I looked, and while I found a large number of entries that were dancing all around this question, I never found nothing which addressed this specific issue.   We currently use an ASA 5520 as the head end of a relatively large customer to site IPSEC VPN (approximately 240 users, not consecutively).   This ASA is currently sitting behind a Checkpoint firewall with a real publicly addressable IP address on its public interface.  All of our customers use the legacy Cisco VPN (not the one anyconnect) client.  We plan to a few controllers F5 link set up between ISPS and firewalls.   For VPN connectivity F5 recommends that we NAT IP address (called a broad IP) to point back to a private IP address on the ASA and F5.  My question is, will this work?   I've always heard say that the head of line needed to have a public IP address on this subject because this is what will be placed in packages for the client to respond to.

  For further information, here's what we have now and what we are invited to attend.

  Current

  ISP - router - firewall-fire - ASA (public IP address as endpoint)

  Proposed

  ISP - router - F5 (public IP address as endpoint using a NAT to ASA) - Firewall - ASA (10.X.X.X as its external interface)

  Proposed alternative

  ISP - router - F5 (public IP address as endpoint using a NAT to ASA) - ASA (10.X.X.X as its external interface)

  All thoughts at this moment would be greatly appreciated.   Thank you!

  Hello

  If there is a static NAT one by one on F5 to the external interface of the ASA, then I don't think they would be any problems.
  Because when the client will attempt to connect to IKE to the translated public IP, F5 will redirect the request to ASA outside interface that is configured for the VPN.

  In addition, to ensure the udp500, 4500 and esp is allowed and then you should be good to go.

  HTH

  Concerning
  Mohit

• ASA 5520 - SSL VPN (Anyconnect) licenses

  Hello

  Can someone clarify for me the SSL VPN/AnyConnect for the ASA 5520 license?  Specifically, the differences between the AnyConnect Essentials and AnyConnect Premium.  Our current license looks like this:

  The devices allowed for this platform:
  The maximum physical Interfaces: unlimited
  VLAN maximum: 150
  Internal hosts: unlimited
  Failover: Active/active
  VPN - A: enabled
  VPN-3DES-AES: enabled
  Security contexts: 2
  GTP/GPRS: disabled
  SSL VPN peers: 2
  Total of the VPN peers: 750
  Sharing license: disabled
  AnyConnect for Mobile: disabled
  AnyConnect Cisco VPN phone: disabled
  AnyConnect Essentials: disabled
  Assessment of Advanced endpoint: disabled
  Proxy sessions for the UC phone: 2
  Total number of Sessions of Proxy UC: 2
  Botnet traffic filter: disabled

  This platform includes an ASA 5520 VPN Plus license.

  I guess that means that we have just the 2 'free trial' SSL VPN licenses and nothing else.

  I would like to add 25 or maybe 50 SSL VPN licenses and be able to use a combination of full free client, thin client and groups client AnyConnect.  The 'ASA5500-SSL-25' (or 50) would be the correct license I need to buy?

  Thank you

  Rob

  Hello

  The essentials license is per device and does not allow full-tunnel.

  If you need other features like Secure Desktop, without client SSL and other optional features such as shared licenses, you must go to the Premium license.

  http://www.Cisco.com/en/us/prod/collateral/vpndevc/ps6032/ps6094/ps6120/data_sheet_c78-527494_ps10884_Products_Data_Sheet.html

  Federico.

• IKEv2 VPN without using licensed SSL? (ASA-5512)

  Hi all

  I enabled Cisco 'Anyconnect Premium peers' for customer less connections vpn ssl, the obvious snag is that for Anyconnect ikev2 sessions he wants to use the SSL license pool instead of the IPSEC pool (which I have a lot of connection for 'peers VPN Total: 250' licenses.

  * Is it possible to configure Anyconnect to connect through IPSEC and use licensed IPSEC (while keeping Premium Anyconnect active peers)?

  * Should I consider 3rd third-party vpn outside Anyconnect clients?

  CyA

  Craig

  Remote access to sessions with IKEv2 will always consume a Premium license. Change for another customer will not help unless you change to a customer that uses the legacy technology with EasyVPN. But this should not be the solution.

  If you enable AnyConnect Essentials, you can use AnyConnect with IPSec the platform limit, but you cannot use the features award (as a clientless) more at the same time.

  In a situation like that where many AnyConnect-Sessions are necessary and only a couple of sessions without client, I installed AnyConnectEssentials on the ASA principal and deployed an another ASA only for VPN without client. Due to the high cost of premium VPN licenses, is much cheaper then buying the Premium licenses for all VPN users.

  Sent by Cisco Support technique iPad App

• Routing with Cisco ASA 5520 VPN

  I have installed IPsec vpn remote users in the Cisco ASA 5520 using RADIUS in my main network. Works very well. I have a site to my Cisco ASA5520 tunnels going to other sites, some of the tunnels have Cisco ASA and some have SonicWalls. I wish that my users VPN remote IPSec to be able to navigate in these tunnels is a site to access remote subnets attached to these tunnels. Do I need to use a combination of routing and the ACL? Or can I just use ACL only? Or just use routing only?

  Thank you

  Carlos

  Hello

  The key to set up here is the two ACL of VPN L2L end points that determine the 'interesting' traffic to connect VPN L2L. You will also need to confirm that the connection of the VPN Client is configured so that traffic to the remote sites have sent to the connection of the VPN client. There are also other things that you should check on your ASA plant

  Here most of the things you usually have to confirm

  • Set up 'permit same-security-traffic intra-interface' if it is already present in your configuration
    • This setting will allow connections to form between the hosts that are connected to the same interface on the ASA. In this case, applies because the VPN client users are connected to the interface 'outside' of the ASA and also remote sites are connected to the ASA to "external". If the traffic between the remote VPN Client and VPN L2L sites will be to enter and exit the same interface
  • You will need to check how the customer if configured VPN connection. Split or full Tunnel tunnel
    • If the connection of the VPN Client is configured as Split Tunnel then you need to add all the networks from the remote to the Split Tunnel, so that the connections between the VPN Client is transmitted to the ASA and from there connections VPN L2L
    • If the connection of the VPN Client is configured as full Tunnel, then there no problem that all traffic is transferred to the Client VPN connection all its assets
  • Define the VPN pool in the ACL of VPN L2L
    • You should make sure that the pool network VPN Client is defined in the ACL that define 'interesting' traffic to connect VPN L2L. So, you need to add the pool VPN VPN L2L configurations on the sites of Central America and remote control
  • Configure NAT0 / NAT exempt for remote VPN Client to L2L VPN Site traffic at both ends of the VPN L2L
    • You must ensure that the NAT0 / exempt NAT rules exist for the VPN Client for Remote Site traffic. This will have to be configured on the SAA "outside" interface. Format of configuration varies naturally a bit on the ASA Central his software level.

  These should be the most common things to set up and confirm for traffic to flow between the VPN Client and Remote Sites

  Hope this helps please rate if yes or ask more if necessary.

  -Jouni

• Tunnel VPN ASA 5520 (DMZ + INSIDE) destined for OUTSIDE

  I can't find any reference to anywhere else.

  We have an ASA 5520 to our site HQ (inside the network) with several regional subnets on the DMZ interface.

  We need connectivity VPN Site to Site between the INSIDE and a remote control on the OUTSIDE of the site, as well as between the DMZ subnets and even outside the site. The interface from the OUTSIDE of the SAA must be local VPN endpoint for all tunnels.

  I created a S2S VPN between the INSIDE and the OUTSIDE site and it works great.

  When I create a VPN S2S tunnel between a site of DMZ and even outside the site (using the same settings the and remote, but with a cryptomap different because the local subnet (DMZ) is different from the other inside the subnet, the traffic gets the mapping (show crypto isakmp his) to the same cryptomap that was created for the access to the tunnel from the OUTSIDE) , instead of to the new cryptomap, so remote endpoint deletes it, and traffic also causes SPI incorrect of for the remote endpoint, which makes the original INTERIOR outside OF THE VPN tunnel to fall from time to time.

  Is this a bug?

  I also did a local S2S VPN tunnel configuration test of networks as everything INSIDE and the DMZ. With the help of the wizard VPN S2S leads ASA only to create a NAT rule exempted for the subnet on the INSIDE interface. Can I manually create another tax-exempt NAT rule to the side of the DMZ and use this a S2S tunnel to connect sites inside and DMZ to the remote OFF-SITE in a connection profile?

  I'm building a Rube Goldberg?

  Thank you

  George

  Hi George,.

  It seems you have a situation overlapping it, are you sure that subnets inside did not overlap with the networks from the DMZ?  A package tracer could clarify wha that the ASA is actually sending.

  In addition, you can merge the two interfaces on the same card encryption if you wish, just make sure that the NAT is configured correctly.   For example; Source NAT (all, outside) static...

  It may be useful

  -Randy-

• How many group Supportepar ASA 5520 vpn for remote access

  Hello

  Howmany vpn group is supported on asa 5520 with configuraion vpn remote access.

  Concerning

  1 if nat-control is disabled and you do not have any other order NAT in your config file, you do not have it. Try to remove the existing "NAT 0" command and "clear xlate."

  2. you must ensure that your network inside know they can go by ASA to access remote vpn client IP. You have any device layer 3 behind the ASA that does the routing. If so, please verify that this is the routing table.