ASA software order of operations

Similar Questions

• Order of operations NAT on Site to Site VPN Cisco ASA

  Hello

  I have a question about the order of operations NAT on Site to Site VPN Cisco ASA 8.2.x. I have a scenario where the internal IP address of the range 10.17.128.x are NATTED IP public 31.10.10.x. below is the config:

  Tunnel normally passes traffic to dmz - 31.10.11.10, 31.10.11.11 servers.

  But the servers NATTED (10.17.128.x <->31.10.10.x) does not work.

  inside_map crypto 50 card value transform-set ESP-3DES-SHA

  tunnel-group 100.1.1.1 type ipsec-l2l

  tunnel-group 100.1.1.1 General-attributes

  Group Policy - by default-PHX_HK

  IPSec-attributes tunnel-group 100.1.1.1

  pre-shared key *.

  internal PHX_HK group policy

  PHX_HK group policy attributes

  VPN-filter no

  Protocol-tunnel-VPN IPSec svc webvpn

  card crypto inside_map 50 match address outside_cryptomap_50

  peer set card crypto inside_map 50 100.1.1.1

  inside_map crypto 50 card value transform-set ESP-3DES-SHA

  inside_map crypto 50 card value reverse-road

  the PHX_Local object-group network

  host of the object-Network 31.10.11.10

  host of the object-Network 31.10.11.11

  host of the object-Network 31.10.10.10

  host of the object-Network 31.10.10.11

  host of the object-Network 31.10.10.12

  host of the object-Network 31.10.10.13

  host of the object-Network 10.17.128.20

  host of the object-Network 10.17.128.21

  host of the object-Network 10.17.128.22

  host of the object-Network 10.17.128.23

  the HK_Remote object-group network

  host of the object-Network 102.1.1.10

  inside_nat0_outbound list extended access permitted ip object-group PHX_Local-group of objects HK_Remote

  ACL_INSIDE list extended access permitted ip object-group PHX_Local-group of objects HK_Remote

  ACL_OUTSIDE list extended access permitted ip object-group HK_Remote-group of objects PHX_Local

  outside_cryptomap_50 list extended access permitted ip object-group PHX_Local-group of objects HK_Remote

  Route outside 102.1.1.10 255.255.255.255 30.1.1.1 1

  public static 31.10.10.10 (Interior, exterior) 10.17.128.20 netmask 255.255.255.255

  public static 31.10.10.11 (Interior, exterior) 10.17.128.21 netmask 255.255.255.255

  public static 31.10.10.12 (Interior, exterior) 10.17.128.22 netmask 255.255.255.255

  public static 31.10.10.13 (Interior, exterior) 10.17.128.23 netmask 255.255.255.255

  He started to work when I did another group of object by name PHX_Local1 and added to the list of access inside_nat0_outbound, instead of the object group PHX_Local, as below:

  the PHX_Local1 object-group network

  host of the object-Network 31.10.10.10

  host of the object-Network 31.10.10.11

  host of the object-Network 31.10.10.12

  host of the object-Network 31.10.10.13

  No inside_nat0_outbound access list extended only to allowed ip object-group PHX_Local-group of objects HK_Remote

  inside_nat0_outbound list extended access permitted ip object-group PHX_Local1-group of objects HK_Remote

  Can you please help me understand why group object PHX_Local failed with access-list inside_nat0_outbound, but he began to work with the Group of objects PHX_Local1.

  Also, if you could tell me the order of operations to NAT via VPN Site to Site, it would be useful.

  Thank you

  Kind regards

  Thomas

  Hello

  I think you could have said the original question in a way that could be missleading. In other words, if I understand now.

  From what I understand now, you have the DMZ set up the server that are measured with a public IP address on the real servers. And for those that you have configured NAT0.

  Then you have other servers that do not have public IP addresses themselves, but they are translated on the SAA.

  If this is the case, then the next question would be. The server with the NAT should attend the L2L VPN connection with their real IP or address IP NAT.

  Of course if you configure static NAT for the same servers and NAT0 the NAT0 will always win.

  You have these guests who were not able to use the VPN L2L

  31.10.10.10 10.17.128.20

  31.10.10.11 10.17.128.21

  31.10.10.12 10.17.128.22

  31.10.10.13 10.17.128.23

  IF you want them to go to the VPN L2L with their original IP address then you must configure

  object-group, LAN

  host of the object-Network 10.17.128.20

  host of the object-Network 10.17.128.21

  host of the object-Network 10.17.128.22

  host of the object-Network 10.17.128.23

  object-group, REMOTE network

  host of the object-Network 102.1.1.10

  inside_nat0_outbound list extended access allowed ip-group of objects LOCAL object-group remote

  outside_cryptomap_50 list extended access allowed ip-group of objects LOCAL object-group remote

  IF you want to use the L2L VPN with the public IP address, then you must configure

  object-group, LAN

  host of the object-Network 31.10.10.10

  host of the object-Network 31.10.10.11

  host of the object-Network 31.10.10.12

  host of the object-Network 31.10.10.13

  object-group, REMOTE network

  host of the object-Network 102.1.1.10

  outside_cryptomap_50 list extended access allowed ip-group of objects LOCAL object-group remote

  EDIT: in this case you naturally do not configure any NAT0 for actual IP addresses we want precisely the IP addresses to be visible to the L2L VPN with the IP NAT address.

  Or you can of course use the same "object-group" as currently but change the content in an appropriate manner

  Be sure to mark it as answered if it was answered.

  Ask more if necessary

  -Jouni

• How to make a copy of all the software and the operating system that came stock with the laptop?

  I have a laptop that I have replaced the motherboard and now HD took a dump and should be replaced also. I need the software and the operating system disk, so I can restore the operating system to order.

  Please advise!

  This link will take you to a web document that explains how to order a recovery for the initially installed operating system disk.

  Here is the support for your laptop computer portal.

  Best regards

  ERICO

• Order of operations

  What is the best order of operations to perform an upgrade of RAM, upgrade the OS and firmware update on a freshly wiped Macbook?

  The laptop in question is a Macbook version 7.1; 2.4 GHz; 250GB, 2x1GB RAM.

  I have the installation discs for Snow Leopard.

  I want to upgrade to El Capitan, and I would like to install 16 GB of RAM (2X8GB), I understand that this model can accept 16BG despite the specs from Apple.

  The System Profiler indicates that the firmware is not the latest version, which is believe is necessary for the 16 GB of RAM to work.

  To update the firmware, I would need to install it (temporarily) Snow Leopard, correct? And then should I upgrade the RAM, then the OS? Or is there a better order?

  Thanks for any idea.

  a. install the original OS first to see if that works correctly.

  b. then update the firmware, and it should work correctly after that too.

  c. now you can go after your wishes, without slipping questions with you:

  install more RAM using 2x8GB modules of the correct specifications (PC3-8500 (1066 MHz) of 204-pin DDR3 SO-DIMM) have a good brand, Crucial research or OWC.

  Use the mac and see if everything is still OK.

  4. all applications you want to use to ensure compatibility with ElCapitan 10.11.6 research:

  Search developer sites, a general site that helps (not always) is roaringapps.com

  5. check the operation of your Apple ID.

  6. download ElCapitan since the Appstore. You can make a bootable stick with Setup on this topic, if you have a backup before installing ElCapitan in the Applications folder. Then install ElCapitan and enjoy.

  Lex

• We have the assurance of software on the operating system server & CALs client server. License expires in June 2013. expires in June 2013. We need to exercise our upgrade to licences before June 2012?

  Original title: Software Assurance

  We have the assurance of software on the operating system server & CALs client server. Our agreement expires in June 2013. Do we need to exercise our upgrade to the licenses before 2012 June?

  Hello

  Thanks for asking this question to Microsoft Community.

  I suggest you check the Microsoft Software Assurance Web site for assistance.

  http://www.Microsoft.com/licensing/software-assurance/default.aspx

  Software Assurance FAQ:
  http://www.Microsoft.com/licensing/software-assurance/FAQ.aspx

  In addition, you can contact support by calling team: 800-936-3500.

  Hope this information helps.

• Order of operations for PIX

  I intend to migrate from ducts in the ACL, and I'm interested to know the order of operations.

  Lets assume that I have access list on the external interface that allows the packet HTTP & HTTPS to the Web server. However, on the DMZ interface I encouraged only SMTP packets.

  Do I need to allow packets to the Web server on the DMZ interface?

  Can't control the before State of ACL table PIX?

  (Please let me know if there is any document which deals with the order of operations.)

  Thank you.

  I'm a little confused by your example, but I think I know what you're looking for.

  Yes, the PIX search a connection exstablished front of LCD. Therefore, if the package has been allowed in through the ACL on your external interface on a server web DMZ, the answer would automatically be allowed. You must enable explicitly all traffic through the ACL on the interface DMZ that you wanted to come (initiated, this isn't an answer) of the web server on the DMZ. For example, open a web browser on the web server itself should be allowed.

  And ACL have a higher priority than the pipes so mix are not a good idea (just an info).

  Scott

• NAT order of operation on the PIX firewall

  Hi all.

  Can someone refer me to a document that clearly explains the order of operations on a PIX w firewall NAT / code 6.3 (3) or 6.3 (5)?

  The statements are first aveluated? Static Nat, static policy NAT, NAT/PAT dynamics and so forth, for outbound connections?

  And for incoming connections? I know that xlate table is checked on the first place for incoming connections, but, assuming that there is no entry corresponds to an incoming packet... What is the medal in which NAT set out are avaluated?

  TKS in advance.

  Diego

  Hello

  Refers to these positions. These are the same though...

  http://Forum.Cisco.com/eForum/servlet/NetProf?page=NetProf&Forum=security&topic=firewalling&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1ddb829a/0#selected_message

  http://Forum.Cisco.com/eForum/servlet/NetProf?page=NetProf&Forum=security&topic=firewalling&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1ddb999a/1#selected_message

  HTH

  AK

• What is the order of operations

  Where can I find the order of operations that are evaluated by the Oracle database? I mean, for example, for a query like this:

  Select an element, rank on (partition of order in...) r

  from t1, t2

  where t1.x = t2.x

  and t2.other_something = 'value '.

  order by 1;

  We can say that: "order by" going to last, "rank" works on lines after that the paintings are "United" and "selected". So in a sense, there is an order of operations. I understand that the actual order of operations when execution can be different if optimizer concludes on an equivalent, alternative execution plan. But what is a sort of operations of op "basic" order Oracle follows "to understand" the request even before trying to understand the alternative form. Is there such a list of order of operations?

  Thank you

  Hello

  946279 wrote:

  Where can I find the order of operations that are evaluated by the Oracle database? I mean, for example, for a query like this:

  Select an element, rank on (partition of order in...) r

  from t1, t2

  where t1.x = t2.x

  and t2.other_something = 'value '.

  order by 1;

  We can say that: "order by" going to last, "rank" works on lines after that the paintings are "United" and "selected". So in a sense, there is an order of operations. I understand that the actual order of operations when execution can be different if optimizer concludes on an equivalent, alternative execution plan. But what is a sort of operations of op "basic" order Oracle follows "to understand" the request even before trying to understand the alternative form. Is there such a list of operations?

  Thank you

  No, I've never seen any kind of official list like that, no doubt because, as you say, the optimizer does not follow these rules; the optimizer has done what he thinks is the fastest way to get the results that you specified.

  It may be useful to imagine things in the following order:

  1. Subqueries
  2. Joins (including the join in the WHERE clause conditions)
  3. PIVOT and UNPIVOT
  4. START WITH and CONNECT BY clauses
  5. WHERE clause
  6. Clause GROUP BY and aggregate functions
  7. HAVING clause
  8. Analytic functions (for example, RANK)
  9. ORDER BY clause

  Again, this has the same relationship to what actaully goes according to the drawings of atoms you see in science books have to the real atoms.  It can help you to remember (for example) that an analytic function (n ° 8 in the list above) may rely on an aggregate function (#6), but not vice versa.

  Yet once, SQL is not a procedural language, and the optimizer does not actually follow a rule of procedure like this.

• order of operations in the execution plan

  Hello

  I'm not sure if my order of the following execution plan is correct.

  So hopefully someone can confirm or refute my order of the plan.

  
  

  This is the query:

  SELECT DISTINCT 'A3. ' "' ISIN '.

  Of

  "WERTPAPIERE" "A3."

  "LOGTABLE" "A2."

  "WP_STATUS" "A1".

  WHERE

  "A2". "PK_ID"= "A3". "" IDENTITY CARD "AND

  "A2". "" REFERENCE "> TIMESTAMP' 2014-01-06 18:30 ' AND

  "A2". "" REFERENCE "< = TIMESTAMP' 2014-01-08 07:00 ' AND

  "A2". "" LOG_DATUM "> TIMESTAMP' 2014-01-07 18:30 ' AND

  "A2". "" LOG_DATUM "< = TIMESTAMP' 2014-01-08 07:00 ' AND

  "A2". "TABLE" = "WERTPAPIERE" AND "

  "A3". ' BATCH '= 'A1'. "" IDENTITY CARD "AND

  "A1". "" CODE "<>" * 33' AND "

  (THERE ARE

  (SELECT "BESTANDS_MERKM" 0 "A7"

  WHERE 'A7 '. "ID"= "A3". "' BESTANDS_MERKMAL_ID ' AND ('A7'. "CODE"= "1" OR "A7". "CODE"(= '2')) AND ("A3" ".") " USER name "= 'Ect' OR 'A3'." USER name "= 'pro' OR 'A3'". "" Username "(= 'prom') or does NOT EXIST"

  (SELECT 0

  OF 'BESTANDS_MERKM' "A6".

  WHERE "A6". «ID «= NVL ("A3".» ("' BESTANDS_MERKMAL_ID ', 0) AND ("A6". "CODE"= "1" OR "A6". "CODE"(= '2')) AND ("A3" ".") " Username "="Res"OR"A3"." Username "(= 'prom') AND ("A3"". ")" LOESCH_KZ_ID' IS NULL OR EXISTS

  (SELECT 0

  OF 'WERTPAPIER_LOESCH_KZ' "A5".

  WHERE "A5". "ID"= "A3". "' LOESCH_KZ_ID ' AND 'A5 '. (("CODE"="1")) AND THERE ARE

  (SELECT 'PRODUKTGRUPPE_SEGMENT' 0 'A4'

  WHERE "A4". "ID"= "A3". "' PRODUKTGRUPPE_SEGMENTIERUNG_ID ' AND ('A4'. "CODE"= "USE" OR "A4". "CODE"= "ZUUZ" OR "A4". "CODE"= "4000" OR "A4". "CODE"= "5000" OR "A4". "CODE"= "3000" OR "A4". "CODE"= "4444" OR "A4". "CODE"= "4445" OR "A4". "CODE"= "5544" OR "A4". "CODE"= "6544" OR "A4". «CODE ' = ' 6543 "OR"A4".» ((("CODE"="8765')))

  The plan has been acquired through dbms_xplan:

  Select * from table (dbms_xplan.display_cursor (format = > 'ALLSTATS LAST SCHEMA'));

  
  

  Here's the plan:

  
  

  -----------------------------------------------------------------------------------------------------------------------------------------------------------------

  | ID | Operation | Name                     | Begins | E - lines. A - lines.   A - time | Pads | Bed |  OMem |  1Mem | Used Mem.

  -----------------------------------------------------------------------------------------------------------------------------------------------------------------

  |   0 | SELECT STATEMENT |                          |      1.        |   1252 | 00:05:55.03 |      11 M |    594K |       |       |          |

  |   1.  UNIQUE HASH |                          |      1.  28517 |   1252 | 00:05:55.03 |      11 M |    594K |  1135K |  1135K | 2976K (0) |

  |*  2 |   FILTER                               |                          |      1.        |   2579 | 00:05:55.02 |      11 M |    594K |       |       |          |

  |*  3 |    HASH JOIN |                          |      1.    571K |   2219K | 00:05:53.49 |      11 M |    594K |  1306K |  1306K | 1 272 K (0) |

  |*  4 |     INDEX SCAN FULL | WP_STAT_UPI |      1.     57.     57. 00:00:00.01 |       1.      0 |       |       |          |

  |   5.     NESTED LOOPS |                          |      1.        |   2219K | 00:05:52.17 |      11 M |    594K |       |       |          |

  |   6.      NESTED LOOPS |                          |      1.    583K |   2219K | 00:00:18.62 |     726K |    436K |       |       |          |

  |   7.       RANGE OF SINGLE PARTITION |                          |      1.    583K |   2219K | 00:00:12.29 |     436K |    436K |       |       |          |

  |   8.        PARTITION LIST ALL |                          |      1.    583K |   2219K | 00:00:11.96 |     436K |    436K |       |       |          |

  |*  9 |         TABLE ACCESS FULL | LOGTABLE |      4.    583K |   2219K | 00:00:11.61 |     436K |    436K |       |       |          |

  | * 10 |       INDEX UNIQUE SCAN | WP_PK_I                  |   2219K |      1.   2219K | 00:00:05.34 |     289K |    491.       |       |          |

  |  11.      TABLE ACCESS BY INDEX ROWID | WERTPAPIERE |   2219K |      1.   2219K | 00:05:32.59 |      10 M |    157K |       |       |          |

  | * 12 |    TABLE ACCESS BY INDEX ROWID | BESTANDS_MERKM |      5.      1.      2. 00:00:00.01 |       8.      0 |       |       |          |

  | * 13 |     INDEX UNIQUE SCAN | BESTANDS_MERKM_PK_I |      5.      1.      4. 00:00:00.01 |       4.      0 |       |       |          |

  | * 14 |    TABLE ACCESS BY INDEX ROWID | BESTANDS_MERKM |      3.      1.      0 | 00:00:00.01 |       5.      0 |       |       |          |

  | * 15 |     INDEX UNIQUE SCAN | BESTANDS_MERKM_PK_I |      3.      1.      2. 00:00:00.01 |       3.      0 |       |       |          |

  | * 16.    TABLE ACCESS BY INDEX ROWID | PRODUKTGRUPPE_SEGMENT |      3.      1.      2. 00:00:00.01 |       6.      0 |       |       |          |

  | * 17.     INDEX UNIQUE SCAN | PRG_SEG_PK_I |      3.      1.      3. 00:00:00.01 |       3.      0 |       |       |          |

  | * 18.    INDEX UNIQUE SCAN | WERTPAPIER_LOESCH_KZ_UPI |      2.      1.      1. 00:00:00.01 |       2.      0 |       |       |          |

  -----------------------------------------------------------------------------------------------------------------------------------------------------------------

  Vector data

  -------------

  /*+

  BEGIN_OUTLINE_DATA

  IGNORE_OPTIM_EMBEDDED_HINTS

  OPTIMIZER_FEATURES_ENABLE ('11.2.0.3')

  DB_VERSION ('11.2.0.3')

  ALL_ROWS

  OUTLINE_LEAF(@"SEL$2")

  OUTLINE_LEAF(@"SEL$3")

  OUTLINE_LEAF(@"SEL$4")

  OUTLINE_LEAF(@"BLOCK1")

  OUTLINE_LEAF(@"SEL$1")

  OUTLINE(@"BLOCK1")

  FULL (@"SALT$ 1" "A2"@"SEL$1")

  INDEX (@"SALT$ 1" "A3"@"SEL$1" ("WERTPAPIERE".) "ID")) "

  INDEX (@"SALT$ 1" "A1"@"SEL$1" ("WP_STATUS".) "CODE" "WP_STATUS" "." " ID'))

  LEADING (@"SALT$ 1" "A2"@"SEL$1" "A3"@"SEL$1" "A1"@"SEL$1")

  USE_NL (@"SALT$ 1" "A3"@"SEL$1")

  NLJ_BATCHING (@"SALT$ 1" "A3"@"SEL$1")

  USE_HASH (@"SALT$ 1" "A1"@"SEL$1")

  SWAP_JOIN_INPUTS (@"SALT$ 1" "A1"@"SEL$1")

  USE_HASH_AGGREGATION(@"SEL$1")

  INDEX_RS_ASC (@"BLOCK1" "A4"@"BLOCK1" ("PRODUKTGRUPPE_SEGMENT".) "ID")) "

  INDEX (@"SALT$ 4" "A5"@"SEL$4" ("WERTPAPIER_LOESCH_KZ".) "CODE" "WERTPAPIER_LOESCH_KZ" "." " ID'))

  INDEX_RS_ASC (@"SALT$ 3" "A6"@"SEL$3" ("BESTANDS_MERKM".) "ID")) "

  INDEX_RS_ASC (@"SALT$ 2" "A7"@"SEL$2" ("BESTANDS_MERKM".) "ID")) "

  END_OUTLINE_DATA

  */

  According to independent-combine- JOIN operation by HASH, I assumed the first operation's Id 4 because the "INDEX FULL SCAN' on 'WP_STAT_UPI' is the first child.

  So I guess the order of operations by Id is 4,9,10 and so on.

  I got my information from the official oracle documentation, the book of Troubleshooting Oracle Performance (APRESS) and some research on the internet.

  Unfortunately so far I have found a good documentation on the scheduling. Most of the tutorials and documentation talk a lot operations themselves, but very little about the opening sequence.

  According to the section ATTACK to State "LEADING(@"SEL$1""A2"@"SEL$1""A3"@"SEL$1""A1"@"SEL$1")", for the classification should be Id: 9,10 and so on.

  
  

  I also tried to find order information in the v$ sql_plan. The database version is 11.2.
  

  
  

  Any help welcome.

  
  

  Best regards
  

  Your interpretation is correct (even if you have obscured the lines 5-8, but they do not add significant value to what you're saying).

  The explanation of the difference between your interpretation and the indicator leading() is the indicator USE_HASH() is accompanied by a hint of swap_join_inputs(). Hash joins | Oracle scratchpad indicator tells you the order of join optimizer was examining, but the optimizer exchange the roles of man and hash tables when it comes to her 'now to join A1 (WP_STAT)' part of the analysis - and this is reflected in the implementation plan.

  Symbolically, the main indicator says

  You should join A2 and A3--> (A2, A3)

  Then you must join A1--> ((A2, A3), A1)

  But Exchange - join entries. (A1, (A2, A3))

  Concerning

  Jonathan Lewis

• RemoteObject order of operations

  I need help understanding the order of operations in Flex. I have an initApp() function that is called in the attribute of the tag in the Application creationComplete. Inside this function, I try to call four different methods of a single RemoteObject and then move the tables returned each RO function to another function that combines all of the tables.
  
  (see code below)
  
  The problem occurs in the assembleTreeArray function because none of the tables being moved in have something in them.
  
  When I throw in a bunch of breakpoints and step by step application, I noticed that the whole function initApp() runs before the RO result handler functions are called. With that being the case, when can I run the assembleTreeArray function?
  
  Thanks for the advice or nudges in the right direction.
  -Scott
  
  

  You have four calls to the remote object, each of which will return in no particular order and asynchronously.

  The functions of result can each call assembleTreeArray. assembleTreeArray can test to see if the four ArrayCollections are available (non-null) and when they are it can assemble the table.

• Cisco asa 9.1: crypto acl - order, order of operations,.

  Hello

  Let's say we have the following configuration

  VPN1 list extended access permitted ip 192.168.1.0 255.255.255.0 10.0.0.0 255.0.0.0

  card crypto mymap 10 correspondence address vpn1

  card crypto mymap 10 peers set x.x.x.x

  access-list extended 192.168.1.0 ip VPN2 allow 255.255.255.0 10.1.1.0 255.255.255.0

  mymap 20 match address vpn2 crypto card

  card crypto mymap 20 peers set y.y.y.y

  In the above example, what happens if you intend to send a packet to a host on the 10.1.1.x and her counterpart that x.x.x.x is down (not SA).

  If Asa will verify that the SA is down or away he starts the process of the next crypto access list according to the sequence number of crypto card? or simply drag the package?

  If Asa trial next crypto map entry/crypto acl and that if no matching ACL? Packets are sent as clear text?

  Thank you explantion

  Peter

  Hi Peter,.

  This would work if the first tunnel is down and there is not SA for her.

  However, it is not recommended to overlap crypto ACL.

  Kind regards

  Aditya

  Please evaluate the useful messages and mark the correct answers.

• If you use SSD what size minimum, you can use I'll just install the softwar winds 7 operation and put all the other programs on a hard drive Sata is the way it should be done?

  I'm building a new PC, I have the motherboard and it has a location for an SSD, this who has the ability of minium are? and if this store just drive the sofware opererating only, as I intend to have all my programs and data on a SATA hard drive is the way to corect to go? Could someone ' a please advise please.

  The minimum I recommend is 80 GB, if you can go for 128 GB to 160 GB, I would go for it.

  Windows 7 uses 10 GB of disk space, and you have to take into account future, Service Packs and updates.

  You must also consider your page file size that will depend on the amount of RAM you have installed.

  Other disk space requirements include your programs and hardware drivers.

  The benefits of having an SSD is to accelerate the performance of the operating system and applications. In order to have a just installed SSD for upgrading the operating system on a mechanical HDD as well as your programs wouldn't make sense. Store content or data that you create on the HARD disk.

• software order questions

  Hello, I bought students year Software hosted yesterday evening and I received an email saying that you have problems with your ordering system. I really need this software as soon as POSSIBLE, and he said I would be back here today, but I did not yet? I was wondering what was happening with my order now and when I get it?

  To the link below, click on the still need help? option in the blue box below and choose the option to chat or by phone...
  Make sure that you are logged on the Adobe site, having cookies enabled, clearing your cookie cache.  If it fails to connect, try to use another browser.

  Creative cloud support (all creative cloud customer service problems)
  http://helpx.Adobe.com/x-productkb/global/service-CCM.html ( http://adobe.ly/19llvMN )

• Order of operations under pl

  in this operation
  
  validTo > = trunc (SYSDATE - 35 + 1/24).
  
  Operations would be done in which order?
  
  1 SYSDATE - 35.
  2 + 1/24?
  
  Or vice versa?
  
  Thanks in advance

  Less and more have equal priority. Mathematically, the answer remains the same, no matter what either less or more is done first.

  SQL> select 1+2-1 as ANSWER from dual;
  
      ANSWER
  ----------
           2
  
  SQL> select 1+(2-1) as ANSWER from dual;
  
      ANSWER
  ----------
           2
  
  SQL> select (1+2)-1 as ANSWER from dual;
  
      ANSWER
  ----------
           2
  
  SQL> 
  

• Lost software possibly stolen operating system (XP).

  I upgraded my OS from millenium to XP PRO a couple of years and registered. I recently came across some problems that I have the installation disc for. until a month ago I had the case of disk with all of the information in this case. We recently had a few flights in our House for which the culprit was caught. I went unnoticed that he could take my drive because I always leave with my folder on the computer. The target of culprits was computer and our identities. Yet once again, I did not notice that the housing and the drive was taken to a well. My question is. Given that I register the software with Microsoft can I replace through Microsoft.

  Microsoft does not make this kind of tracking software, and even if they don't that Windows XP has been withdrawn from the market for many years already make impossible replacement.