ASA VS 3 G/GPRS
Hello world!!
We want to work with the ASA VPN with customers with 3 G/GPRS devices.
Need a special permit? Material 3 G/GPRS can be connected without the mobile AnyConnect?
Thanks in advance
Hi Francisco,.
I'm assuming that users will always have AnyConnect installed on Windows\Mac\Linux but they will use just a GPRS\3G Modem to WAN connectivity?
If above is true you don't need any license of Mobile special license.
However, if users must connect using AnyConnect installed on the iPhone, etc. then you will need a mobile license.
Thank you
Naman
Tags: Cisco Security
Similar Questions
-
Features licensed on an ASA update
The device is a Cisco ASA 5520 9.1 (4) running.
Installing AnyConnect Essentials and AnyConnect for Mobile.
Already have a license for AnyConnect Premium peer (10 users).
I was wondering if I can simply install the new AnyConnect Essentials license regardless of the existing license Premium AnyConnect peers.
I was wondering if the AnyConnnect for the Mobile license recognizes the number of users associated with the AnyConnect Essentials license or license Premium AnyConnect peers.
The devices allowed for this platform:
The maximum physical Interfaces: unlimited perpetual
VLAN maximum: 150 perpetual
Guests of the Interior: perpetual unlimited
Failover: Active/active perpetual
Encryption - A: enabled perpetual
AES-3DES-Encryption: activated perpetual
Security contexts: 2 perpetual
GTP/GPRS: Disabled perpetual
AnyConnect peers Premium: 10 perpetual
AnyConnect Essentials: Disabled perpetual
Counterparts in other VPNS: 750 perpetual
Total VPN counterparts: 750 perpetual
Shared license: disabled perpetual
AnyConnect for Mobile: disabled perpetual
AnyConnect Cisco VPN phone: disabled perpetual
Assessment of Advanced endpoint: disabled perpetual
Proxy UC phone sessions: 2 perpetual
Proxy total UC sessions: 2 perpetual
Botnet traffic filter: activated 281 daysIntercompany Media Engine: Disabled perpetual
Cluster: Disabled perpetualThis platform includes an ASA 5520 VPN Plus license.
AnyConnect Essentials and Premium AnyConnect can exist as the licenses on an ASA, but either one or the other can be used.
Once you enter the command "anyconnect essentials", it allows to disable all features you may have configured to use the Premium license.
-
Hi all
We bought a new device of 5515 x ASA. I'm confused with the license available on the device.
How many users can connect with the Anyconnect VPN client to the device?
The maximum physical Interfaces: unlimited perpetual
VLAN maximum: 100 perpetual
Guests of the Interior: perpetual unlimited
Failover: Active/active perpetual
Encryption - A: enabled perpetual
AES-3DES-Encryption: activated perpetual
Security contexts: 2 perpetual
GTP/GPRS: Disabled perpetual
AnyConnect Premium peers: 2 perpetual
AnyConnect Essentials: Disabled perpetual
Counterparts in other VPNS: 250 perpetual
Total VPN counterparts: 250 perpetual
Shared license: disabled perpetual
AnyConnect for Mobile: disabled perpetual
AnyConnect Cisco VPN phone: disabled perpetual
Assessment of Advanced endpoint: disabled perpetual
Proxy total UC sessions: 2 perpetual
Botnet traffic filter: disabled perpetual
The IPS Module: Disabled perpetual
Cluster: Activated perpetual
Members of the cluster: 2 perpetualThis platform includes an ASA 5515 Security Plus license.
FC
Philip AnyConnect 4.x licenses are NOT limited to a single ASA (or pair HA). It is a change of 3.x and earlier versions.
You can exchange the PAKs against ASAs as are used for remote access VPN in a given customer.
As long as you do not exceed the number of authorized users, you in the terms of the license. The number of users is not currently technically - applied is to the customer, such as advised by their dealer, buy the right level of license.
-
How much max VPN session is my ASA
This is my version to see the ASA5512 VPN
"Other peers VPN: 250" means that I can use 250 IPSEC session? If I still use MAX 250 VPN Cisco AnyConnect Secure Mobility Client session?
"Total peer VPN: 250" means that I can use 2 Anyconnect premium + 248 250 IPSEC or IPSEC session at the same time?"AnyConnect for Mobile: Disabled" means, I can't use AnyConnect Secure mobility Client (smartphone apps) connect to the ASA by AnyConnect SSL? Can I use AnyConnect secure mobility Client (smartphone apps) connect to the ASA by IPSEC?
The devices allowed for this platform:
The maximum physical Interfaces: unlimited perpetual
VLAN maximum: 100 perpetual
Guests of the Interior: perpetual unlimited
Failover: Active/active perpetual
Encryption - A: enabled perpetual
AES-3DES-Encryption: activated perpetual
Security contexts: 2 perpetual
GTP/GPRS: Disabled perpetual
AnyConnect Premium peers: 2 perpetual
AnyConnect Essentials: Disabled perpetual
Counterparts in other VPNS: 250 perpetual
Total VPN counterparts: 250 perpetual
Shared license: disabled perpetual
AnyConnect for Mobile: disabled perpetual
AnyConnect Cisco VPN phone: disabled perpetual
Assessment of Advanced endpoint: disabled perpetual
Proxy UC phone sessions: 2 perpetual
Proxy total UC sessions: 2 perpetual
Botnet traffic filter: disabled perpetual
Intercompany Media Engine: Disabled perpetual
The IPS Module: Disabled perpetual
Cluster: Disabled perpetualTHX
Hello!
ASA5512 can contain up to 250 concurrent VPN of any type: IPsec Site to Site or IPsec Remote access or Anyconnect SSL VPN or IPsec IKEv2, or even without VPN client.
This means you can use 2 Anyconnect premium + 248 IPSEC VPN from Site to Site. Or, for example, 200 simultaneous IPsec Site to Site VPN + 25 Client VPN (IPsec IKEv1) + 25 AnyConnect VPN (SSL or IPsec IKE v2). But not more than 250 and then at the same time.
"AnyConnect for Mobile" is now obsolete. The license for Anyconnect schema was changed in early 2015. You can see the new pattern here:
http://www.Cisco.com/c/dam/en/us/products/security/AnyConnect-og.PDF
With the new scheme, if you need to connect mobile devices (iOS, Android and so on), using the Anyconnect client, you just need to have a license Anyconnect MORE for the necessary amount of users/devices. License AnyConnect more open along the lines in the output of the show version:
AnyConnect Premium Peers : 250 perpetual
AnyConnect for Mobile : Enabled perpetualAnyConnect for Cisco VPN Phone : Enabled perpetualAdvanced Endpoint Assessment : Enabled perpetual
But, despite the exit "AnyConnect peers Premium: 250 perpetual", you will have the right to use no more then amount ordered... If you need advanced features, for example, Suite B cryptography or VPN without customer, you must order license Anyconnect Apex for amount of users/devices needed. For ASA5512, you need to order licenses Anyconnect more or Apex, but no more so for 250 users, because ASA5512 can't take no more then 250 simultaneous connections. If you want to use the Anyconnect client for mobile devices and you use IPsec IKEv2 for VPN, you will also need order licenses Anyconnect more or Apex. I hope this helps. -
Need to improve my image of Cisco ASA 5510 of asa821 - k8.bin to asa903 - k8.bin with the following license. Do I have to purchase a new license with upgrade of the image?
#sh version
Cisco Adaptive Security Appliance Version 8.2 software (1)
Version 6.2 Device Manager (1)
Updated Wednesday, 5 May 09 22:45 by manufacturers
System image file is "disk0: / asa821 - k8.bin.
The configuration file to the startup was "startup-config '.
TMN-5510 294 days 2 hours
Material: ASA5510, 256 MB of RAM, processor Pentium 4 Celeron 1600 MHz
Internal ATA Compact Flash, 256 MB
BIOS Flash M50FW080 @ 0xffe00000, 1024 KB
Hardware encryption device: edge Cisco ASA - 55 x 0 Accelerator (revision 0 x 0)
Start firmware: CN1000-MC-BOOT - 2.00
SSL/IKE firmware: CNLite-MC-Smls-PLUS - 2.03
Microcode IPSec:-CNlite-MC-IPSECm-HAND - 2.04
0: Ext: Ethernet0/0: the address is *.
1: Ext: Ethernet0/1: address is *.
2: Ext: Ethernet0/2: address is *.
3: Ext: Ethernet0/3: address is *.
4: Ext: Management0/0: address *.
5: Int: internal-Data0/0: the address is *.
6: Int: internal-Control0/0: the address is *.
The devices allowed for this platform:
The maximum physical Interfaces: unlimited
VLAN maximum: 100
Internal hosts: unlimited
Failover: Active/active
VPN - A: enabled
VPN-3DES-AES: enabled
Security contexts: 2
GTP/GPRS: disabled
SSL VPN peers: 2
The VPN peers total: 250
Sharing license: disabled
AnyConnect for Mobile: disabled
AnyConnect for Linksys phone: disabled
AnyConnect Essentials: disabled
Assessment of Advanced endpoint: disabled
Proxy sessions for the UC phone: 2
Total number of Sessions of Proxy UC: 2
Botnet traffic filter: disabled
This platform includes an ASA 5510 Security Plus license.
Series number:
Running Activation Key: ****************************************************************************
Registry configuration is 0x1
Last modified by enable_15 to the configuration 22:29:35.255 * Friday, April 4, 2014
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------
Need help
> Do I need to purchase a new license with upgrade of the image?
NO.
But check the:
1)
https://supportforums.Cisco.com/document/48646/ASA-83-upgrade-what-you-n...
(2) to migrate the configuration of 8.21 to 9.03 asking TAC cisco help
-
Am I limited to a certain number of sessions anyconnect? Should clarify it please?
The devices allowed for this platform:
The maximum physical Interfaces: unlimited
VLAN maximum: 200
Internal hosts: unlimited
Failover: Active/active
VPN - A: enabled
VPN-3DES-AES: enabled
Security contexts: 2
GTP/GPRS: disabled
VPN peers: 5000
WebVPN peers: 2
AnyConnect for Mobile: disabled
AnyConnect for Linksys phone: disabled
Assessment of Advanced endpoint: disabled
Proxy UC sessions: 2
It seems that you have the basic licence that only support 2 session anyconnect.
http://www.Cisco.com/en/us/docs/security/ASA/asa82/license/license82.html#wp172967
-
Withdrawal of licence assessment of ASA
Hello
We install a trial license on our ASA 8.4 version for premium Anyconnect and Adv Endpoint protection.
We already have the license keys. But the evaluation period is only 28 days and after that, the license will not be valid.
How to return to the previous level of license after the eval license period is over?
Help, please.
Kind regards
Anand
SH version
Cisco Adaptive Security Appliance Software Version 7.0000 23
Version 7.3 Device Manager (3)Update on Tue, 09-Oct-14 15:45 by manufacturers
System image file is "disk0: / asa847-23 - k8.bin.
The configuration file to the startup was "startup-config '.ASA in 73 days, 2 hours ago
Material: ASA5510-K8, 1024 MB RAM, Pentium 4 Celeron 1600 MHz processor
Internal ATA Compact Flash, 256 MB
BIOS Flash M50FW080 @ 0xfff00000, 1024 KBHardware encryption device: edge Cisco ASA - 55 x 0 Accelerator (revision 0 x 0)
Start firmware: CN1000-MC-BOOT - 2.00
SSL/IKE firmware: CNLite-MC-Smls-PLUS - 2.03
Microcode IPSec:-CNlite-MC-IPSECm-HAND - 2.06
Number of Accelerators: 10: Ext: Ethernet0/0: the address is 001b.2a34.b77a, irq 9
1: Ext: Ethernet0/1: the address is 001b.2a34.b77b, irq 9
2: Ext: Ethernet0/2: the address is 001b.2a34.b77c, irq 9
3: Ext: Ethernet0/3: the address is 001b.2a34.b77d, irq 9
4: Ext: Management0/0: the address is 001b.2a34.b779, irq 11
5: Int: not used: irq 11
6: Int: not used: irq 5The devices allowed for this platform:
The maximum physical Interfaces: unlimited perpetual
VLAN maximum: 100 perpetual
Guests of the Interior: perpetual unlimited
Failover: Active/active perpetual
VPN - A: enabled perpetual
VPN-3DES-AES: activated perpetual
Security contexts: 2 perpetual
GTP/GPRS: Disabled perpetual
AnyConnect Premium peers: 2 perpetual
AnyConnect Essentials: Disabled perpetual
Counterparts in other VPNS: 250 perpetual
Total VPN counterparts: 250 perpetual
Shared license: disabled perpetual
AnyConnect for Mobile: disabled perpetual
AnyConnect Cisco VPN phone: disabled perpetual
Assessment of Advanced endpoint: disabled perpetual
Proxy UC phone sessions: 2 perpetual
Proxy total UC sessions: 2 perpetual
Botnet traffic filter: disabled perpetual
Intercompany Media Engine: Disabled perpetualThis platform includes an ASA 5510 Security Plus license.
Serial number: JMX1116L1BK
Activation key permanent running: 0 x 62037353 0x3425458a 0xccf1d564 0xae340060 0x0d1007a4Anand,
You can simply enter «disable
activation key» Reference. In addition, you can leave it just coming out and it will not be available after evaluation of timer period is exhausted.
In both cases, he ASA should return to the level of initial permanent license.
-
Would become Anyconnect essentials Premium AnyConnect vpn on asa
Dear team,
We have a pair of cisco ASA 5520 with version 8.2 (5) works well with active mode / standby. As the situation requires, we intend to change the SSL vpn to clientless SSL VPN (AnyConnect Premium) to anyconnect vpn with mobile clients (IOS & Android)
Please specify below
(1) I have read, we cannot have two Anyconnect Essentials & AnyConnect Premium on the same system time. We need to disable accordingly to our need-pl correct me?
(2) what is the best way to have the device for end-user client deployment? pushing of ASA or install individually on the system? Can I have the best, I mean the latest version of windows, client MAC e.t.c I shud get?
While pushing ASA LU that much memory cache will be used, since we have IPS (AIP - SSM) modules has also installed on ASA who shud method I adopt here?
(3) what is the exact product for license Anyconnect Essentials & customer name mobile (IOS & Android) we get from cisco?
(4) once I get the correct license how do I active in systems? should I remove the failover command and install the license in two devices separately?
(5) Finally, I need to authenticate vpn anyconnect essentials with LDAP that is already configured for clientless SSL VPN(AnyConnect Premium). any suggestions here?
Below the version Sh emitted by the devices, it seems essential Anyconnect is already active... Please correct me?
Active Firewall
===============System image file is "disk0: / asa825 - k8.bin.
The configuration file to the startup was "startup-config '.Material: ASA5520, 2048 MB RAM, Pentium 4 Celeron 2000 MHz processor
Internal ATA Compact Flash, 256 MB
BIOS Flash Firmware Hub @ 0xffe00000, 1024 KBHardware encryption device: edge Cisco ASA - 55 x 0 Accelerator (revision 0 x 0)
Start firmware: CN1000-MC-BOOT - 2.00
SSL/IKE firmware: CNLite-MC-Smls-PLUS - 2.03
Microcode IPSec:-CNlite-MC-IPSECm-HAND - 2.050: Ext: GigabitEthernet0/0: the address is a493.4ca3.ce0a, irq 9
1: Ext: GigabitEthernet0/1: the address is a493.4ca3.ce0b, irq 9
2: Ext: GigabitEthernet0/2: the address is a493.4ca3.ce0c, irq 9
3: Ext: GigabitEthernet0/3: the address is a493.4ca3.ce0d, irq 9
4: Ext: Management0/0: the address is a493.4ca3.ce09, irq 11
5: Int: internal-Data0/0: the address is 0000.0001.0002, irq 11
6: Int: internal-Control0/0: the address is 0000.0001.0001, irq 5The devices allowed for this platform:
The maximum physical Interfaces: unlimited
VLAN maximum: 150
Internal hosts: unlimited
Failover: Active/active
VPN - A: enabled
VPN-3DES-AES: enabled
Security contexts: 2
GTP/GPRS: disabled
SSL VPN peers: 2
Total of the VPN peers: 750
Sharing license: disabled
AnyConnect for Mobile: disabled
AnyConnect Cisco VPN phone: disabled
AnyConnect Essentials: enabled
Assessment of Advanced endpoint: disabled
Proxy sessions for the UC phone: 2
Total number of Sessions of Proxy UC: 2
Botnet traffic filter: disabledThis platform includes an ASA 5520 VPN Plus license.
=====================================================
Firewall standby
================Updated Saturday, May 20, 11 16:00 by manufacturers
System image file is "disk0: / asa825 - k8.bin.
The configuration file to the startup was "startup-config '.Material: ASA5520, 2048 MB RAM, Pentium 4 Celeron 2000 MHz processor
Internal ATA Compact Flash, 256 MB
BIOS Flash Firmware Hub @ 0xffe00000, 1024 KBHardware encryption device: edge Cisco ASA - 55 x 0 Accelerator (revision 0 x 0)
Start firmware: CN1000-MC-BOOT - 2.00
SSL/IKE firmware: CNLite-MC-Smls-PLUS - 2.03
Microcode IPSec:-CNlite-MC-IPSECm-HAND - 2.050: Ext: GigabitEthernet0/0: the address is 6073.5cab.3fae, irq 9
1: Ext: GigabitEthernet0/1: the address is 6073.5cab.3faf, irq 9
2: Ext: GigabitEthernet0/2: the address is 6073.5cab.3fb0, irq 9
3: Ext: GigabitEthernet0/3: the address is 6073.5cab.3fb1, irq 9
4: Ext: Management0/0: the address is 6073.5cab.3fb2, irq 11
5: Int: internal-Data0/0: the address is 0000.0001.0002, irq 11
6: Int: internal-Control0/0: the address is 0000.0001.0001, irq 5The devices allowed for this platform:
The maximum physical Interfaces: unlimited
VLAN maximum: 150
Internal hosts: unlimited
Failover: Active/active
VPN - A: enabled
VPN-3DES-AES: enabled
Security contexts: 2
GTP/GPRS: disabled
SSL VPN peers: 2
Total of the VPN peers: 750
Sharing license: disabled
AnyConnect for Mobile: disabled
AnyConnect Cisco VPN phone: disabled
AnyConnect Essentials: enabled
Assessment of Advanced endpoint: disabled
Proxy sessions for the UC phone: 2
Total number of Sessions of Proxy UC: 2
Botnet traffic filter: disabledThis platform includes an ASA 5520 VPN Plus license.
Thank you
1 correct. You can run one or the other, but not both.
2 since you have the upgrade memory to 2 GB, you should be fine perform web deployment via the pkg file method.
3. for a 5520, you need:
L-ASA-AC-E-5520 =
L-ASA-AC-M-5520.. .to the Essentials and Mobile licenses respectively.
4. on ASA 8.2, you need licenses for both units. If you upgrade to 8.3 + (8.4 (7) recommend at least), you can share licenses between members of a pair of HA. If you choose not to upgrade, just apply the key of activation on the rescue unit, then on the unit activates. You don't need to move on and in the failover configuration. Failover of the rescue unit status will show as ineligible briefly while he holds the new license is not the case of the active unit. Which will be resolved after you have applied the same license on the main unit. (If you were on 8.3 + would not happen at all).
5. simply create a new connection profile for customers of Essentials by using the same AAA server group.
-
ASA 5520 - SSL VPN (Anyconnect) licenses
Hello
Can someone clarify for me the SSL VPN/AnyConnect for the ASA 5520 license? Specifically, the differences between the AnyConnect Essentials and AnyConnect Premium. Our current license looks like this:
The devices allowed for this platform:
The maximum physical Interfaces: unlimited
VLAN maximum: 150
Internal hosts: unlimited
Failover: Active/active
VPN - A: enabled
VPN-3DES-AES: enabled
Security contexts: 2
GTP/GPRS: disabled
SSL VPN peers: 2
Total of the VPN peers: 750
Sharing license: disabled
AnyConnect for Mobile: disabled
AnyConnect Cisco VPN phone: disabled
AnyConnect Essentials: disabled
Assessment of Advanced endpoint: disabled
Proxy sessions for the UC phone: 2
Total number of Sessions of Proxy UC: 2
Botnet traffic filter: disabledThis platform includes an ASA 5520 VPN Plus license.
I guess that means that we have just the 2 'free trial' SSL VPN licenses and nothing else.
I would like to add 25 or maybe 50 SSL VPN licenses and be able to use a combination of full free client, thin client and groups client AnyConnect. The 'ASA5500-SSL-25' (or 50) would be the correct license I need to buy?
Thank you
Rob
Hello
The essentials license is per device and does not allow full-tunnel.
If you need other features like Secure Desktop, without client SSL and other optional features such as shared licenses, you must go to the Premium license.
Federico.
-
I have 2 questions:
1.I have firewall 2xASA with different licenses.
The devices allowed for this platform:
The maximum physical Interfaces: unlimited
VLAN maximum: 150
Internal hosts: unlimited
Failover: Active/active
VPN - A: enabled
VPN-3DES-AES: enabled
Security contexts: 2
GTP/GPRS: disabled
VPN peers: 750
WebVPN peers: 2
This platform includes an ASA 5520 VPN Plus license.
Hardware encryption device: edge Cisco ASA - 55 x 0 Accelerator (revision 0 x 0)
Start firmware: CNlite-MC-Boot-Cisco - 1.2
SSL/IKE firmware: CNlite-MC-IPSEC-Admin - 3.03
Microcode IPSec:-CNlite-MC-IPSECm-HAND - 2.04
0: Ext: Ethernet0/0: the address is 0018.195b.ccfa, irq 9
1: Ext: Ethernet0/1: the address is 0018.195b.ccfb, irq 9
2: Ext: Ethernet0/2: the address is 0018.195b.ccfc, irq 9
3: Ext: Ethernet0/3: the address is 0018.195b.ccfd, irq 9
4: Ext: Management0/0: the address is 0018.195b.ccf9, irq 11
5: Int: not used: irq 11
6: Int: not used: irq 5
The devices allowed for this platform:
The maximum physical Interfaces: unlimited
VLAN maximum: 50
Internal hosts: unlimited
Failover: disabled
VPN - A: enabled
VPN-3DES-AES: enabled
Security contexts: 0
GTP/GPRS: disabled
VPN peers: 250
WebVPN peers: 2
This platform includes a basic license.
1. in the first output, you can see active/active failover, even I set up active / standby. Why?
2. in the first output, you can see that the platform has VPN Plus license, but second is basic license. How it is linked with the system ASA IOS? Or isn't depends on ASA IOS. Licenses of Ant are burned for some chip on ASA, maybe? Can someone give me the link with more information on this subject.
Thank you
Leo,
As Rick says, there is only one version of the software PIX / ASA for each version. Individual are activated by a license key. So what I wanted to say, is that the 1st device has a license that gives the capacity of 750 concurrent VPN connections, while the 2nd may have 250. The 2nd device also supports VLAN less and a single context.
All these features can be upgraded with a new license key and reboot, no new software would be necessary.
-
ASA 5505 VPN Probs with IPhone 4
Hi all
my boss has a problem with the phone 4. When he is @Home he use his WLAN to download emails from the Exchange Server to the phone. It works without problem. When he's on the road he establish a VPN Tunnel but it cannot download, emails or something else. With the monitor of the ASDM, I see the connection, but no data flow when it use HSDPA, 3G, Edge or GPRS. Has anyone an idea to solve this problem?
The ASA config:
If the VPN works wirelessly, it should also work via GPRS, etc. This means that the configuration of the SAA is correct.
Since iPhone Client VPN is not a Cisco VPN Client, but built Apple VPN Client, please contact Apple for more support on that.
Here are the URL of Cisco, which said that for your reference:
Hope this helps your new.
-
ASA 5510, get the right pair
Hi, I have a 5510 with security more on 7.2 (3) and I'm looking to pick up a 2nd economic unit on eBay to set up like a pair of HA a/s. Of course, there is a little supply, and one I am looking at matches closely enough. My question to the Board of Directors is how special is licensing when it comes to match? Both are Security Plus, and I don't understand why the discrepancies in Max VLAN, security contexts, and a few other parameters.
My reading abt licensing indicates different levels of security over for example Max VLAN is just indicated that 100. I think it's because the #2 is on 7.0 (3). Maybe some of these features have increased in later versions? But I have no way to control until I have buy TI -.
The plan will be to upgrade all two to 8.2 and bump mine to 1 GB to match... I wanted to just make sure that I wouldn't be in a situation where they would not match for some reason any. Thanks in advance
Mine
Material: ASA5510, 256 MB of RAM, processor Pentium 4 Celeron 1600 MHz
Internal ATA Compact Flash, 256 MB
BIOS Flash M50FW080 @ 0xffe00000, 1024 KB
The devices allowed for this platform:
The maximum physical Interfaces: unlimited
VLAN maximum: 100
Internal hosts: unlimited
Failover: Active/active
VPN - A: enabled
VPN-3DES-AES: enabled
Security contexts: 2
GTP/GPRS: disabled
VPN peers: 250
WebVPN peers: 2
This platform includes an ASA 5510 Security Plus license.
Project #2
Material: ASA5510, 1024 MB RAM, Pentium 4 Celeron 1600 MHz processor
Internal ATA Compact Flash, 256 MB
BIOS Flash Firmware Hub @ 0xffe00000, 1024 KBThe devices allowed for this platform:
The maximum physical Interfaces: unlimited
VLAN maximum: 25
Internal hosts: unlimited
Failover: Active / standby
VPN - A: enabled
VPN-3DES-AES: enabled
Security contexts: 0
GTP/GPRS: disabled
VPN peers: 150This platform includes an ASA 5510 Security Plus license.
Hello
Indeed, there are some differences that you need to fix in order to be able to have a failover pair, BUT as you increase her memory... Why don't you go to 8.3 as the restriction of licenses will disappear for failover purposes,
the units will now share it instead to compare
concerning
-
ASA 5510 w / license more lost security contexts
I have an ASA 5510 with license more than security and when I looked the devices a few days ago, I had 2 contexts, however after you have configured the port of Mgm as a regular port contexts show 0, why? I can't find anywhere on the internet where this problem occurred: this is the result of show worm:
Cisco Adaptive Security Appliance Software Version 7.0 (8)
Updated Sunday, 31 May 08 23:48 by manufacturers
System image file is "disk0: / asa708 - k8.bin.
The configuration file to the startup was "startup-config '.
SHIELDASA01 up to 21 hours 16 minutes
Material: ASA5510, 256 MB of RAM, processor Pentium 4 Celeron 1600 MHz
Internal ATA Compact Flash, 256 MB
BIOS Flash M50FW080 @ 0xffe00000, 1024 KB
Hardware encryption device: edge Cisco ASA - 55 x 0 Accelerator (revision 0 x 0)
Start firmware: CNlite-MC-Boot-Cisco - 1.2
SSL/IKE firmware: CNlite-MC-IPSEC-Admin - 3.03
Microcode IPSec:-CNlite-MC-IPSECm-HAND - 2.05
0: Ext: Ethernet0/0: the address is 0021.a025.2d3c, irq 9
1: Ext: Ethernet0/1: the address is 0021.a025.2d3d, irq 9
2: Ext: Ethernet0/2: the address is 0021.a025.2d3e, irq 9
3: Ext: Ethernet0/3: the address is 0021.a025.2d3f, irq 9
4: Ext: Management0/0: the address is 0021.a025.2d3b, irq 11
5: Int: not used: irq 11
6: Int: not used: irq 5
The devices allowed for this platform:
The maximum physical Interfaces: unlimited
VLAN maximum: 25
Internal hosts: unlimited
Failover: Active / standby
VPN - A: enabled
VPN-3DES-AES: enabled
Security contexts: 0
GTP/GPRS: disabled
VPN peers: 150
This platform includes an ASA 5510 Security Plus license.
I'm not showing the serial number and keys licese for obivious reasons. Any help? Thanks in advance.
You might want to try upgrading your IOS on the SAA, see if it can help, can you check the firewall mode (single or multiple) you're currently on? is your asa transparant or routed?
-
ASA 5510 Anyconnect licenses with Cisco Anyconnect VPN IP phone
Hi, hoping someone can shed some light on what I'm just more confused over trying to get by. Not sure if this goes in the section IP Telehpony or here...
We have an ASA 5510 with the base license. We need to install IP phones to home teleworkers, and I understand there are Cisco IP phones that have built-in VPN clients to enable a tunnel to the central private network. IT seems that you can't use Anyconnect VPN to do this, and I am trying to establish what upgrade licenses, we must apply to the ASA, as both Anyconnect licenses that you get for free on the SAA is not enough.
This is the phone that we seek;
I want to know is the Anyconnect Essentials license will work with these IP phones?
When I do a version of the show,
The devices allowed for this platform:
The maximum physical Interfaces: unlimited
VLAN maximum: 50
Internal hosts: unlimited
Failover: disabled
VPN - A: enabled
VPN-3DES-AES: enabled
Security contexts: 0
GTP/GPRS: disabled
SSL VPN peers: 2
The VPN peers total: 250
Sharing license: disabled
AnyConnect for Mobile: disabled
AnyConnect for Linksys phone: disabled
AnyConnect Essentials: disabled
Assessment of Advanced endpoint: disabled
Proxy sessions for the UC phone: 2
Total number of Sessions of Proxy UC: 2
Botnet traffic filter: disabled
This platform includes a basic license.
It shows "AnyConnect for Linksys phone: Disabled", it is the same for the Cisco IP phones? It is the kind of specific license, should I seek for Anyconnect on IP phones or will Essentials?
Hi Leo,
you will need 2 licenses: an Anyconnect Premium license and a permit «Anyconnect of Cisco VPN phone»
ASA 8.2 and earlier license "for Cisco VPN Phone" has been named "for phone Linksys' it's the same.
CFR. http://www.Cisco.com/en/us/docs/security/ASA/asa84/license/license_management/license.html#wp1487574
HTH
Herbert
-
AnyConnect VPN license on ASA 5510
Hello
We have ASA 5510 IPS with basic license. We must now Anyconnect support for more than 2 users.
Anyconnect (tunnel mode) but essentially Anyconnect license enough? Do need me a license for SSL VPN peers?
What about Anyconnect without customer, I see that I need a premium license?
This one is pretty ASA5510-SSL50-K9? It's really expensive compared the Anyconnect Essentials.
Here is my worm out sh:
The devices allowed for this platform:
The maximum physical Interfaces: unlimited
VLAN maximum: 50
Internal hosts: unlimited
Failover: disabled
VPN - A: enabled
VPN-3DES-AES: enabled
Security contexts: 0
GTP/GPRS: disabled
SSL VPN peers: 2
The VPN peers total: 250
Sharing license: disabled
AnyConnect for Mobile: disabled
AnyConnect Cisco VPN phone: disabled
AnyConnect Essentials: disabled
Assessment of Advanced endpoint: disabled
Proxy sessions for the UC phone: 2
Total number of Sessions of Proxy UC: 2
Botnet traffic filter: disabledThis platform includes a basic license.
Yes, AnyConnect Premium includes all the SSL features (including the complete tunnel mode AnyConnect - which is what sustains essential AnyConnect).
So if you buy the 50 user for AnyConnect Premium license, you can have up to 50 SSL VPN connections, if they are the combination of all without customer, or combination of tunnel without customer and full, or just full tunnel. All with a maximum of 50 simultaneous SSL tunnels.
Maybe you are looking for
-
How can I make a set of my pre-installed Windows XP system recovery disks?
How can I make a set of recovery discs from my Windows XP pre-installed system supplied with the machine? It works ok (so not the repair feature). It there is just so much junk from test facilities in the background that I want to do a complete wipe-
-
Blue Screen (screen of death) occurs at the Normal boot and Safe Mode
I have a problem with my acer 1 aspire d255-2351 it starts up like the ordinary thing, you know then this screen blue suddenly pops up then shutts down while I tried all methods to try to resolve the problem, it shows the blue screen I have a pop can
-
Windows Media Player plays only one file at a time
These days, my Media Player acted upward. It will play a music/film without problem, but when I try to play multiple files at the same time it hangs and I have to Ctrl-Alt-Delete to stop the player because it does more. When I try to use it again a
-
Hello I was working on a large Excel file with a formula and stop of Excel to the answer. I restart my PC and go to the response center > troubleshooting > Performance. En error message says that a system problem has prevented this process to continu
-
Create the hyperlink in a text field
I have a form that collects data from a customer. The number of customers is their phone number. This issue is already known and stored in a "cPhone" text field in the form. After all data are collected on the form, I then need to browse the site of