Assignment of the ACS 5.2 VLAN dynamic - problem of vlan voice

Similar Questions

• Get some VLAN voice to work on 5548P

  Hello

  I was wondering if there is a way to accomplish the following. I want the passage to the tag the traffic on its own based on the YES Table and pass it up to the Sonicwall (DHCP server/router) without going through the phone itself do the marking. Is this possible? Currently, the installation so I put manually the VLAN ID on the phone itself, but these phones can work anywhere there is a sense of internet connection if I manually add the tag VLAN, the phone will not work outside of the corporate network.

  Thank you

  If your phone supports LLDP-MED, you can install the switch with a VLAN voice. This wiki covers the implementation of the VLAN voice.

  http://en.community.Dell.com/TechCenter/networking/w/wiki/configuring-Dell-PowerConnect-55xx-series-switch-voice-VLAN.aspx

  Do not have to configure phones that you configure LLDP-MED. The VLAN ID information are passed with LLDP-MED configured on the VoIP phone using the LLDP-MED mechanism. By this method, the voice from the VoIP phone data are tagged with the VLAN ID exchanged and the usual traffic would go to the PVID.

  Here is the link to the user guide. LLDP-MED configuration begins at page 540.

  FTP://FTP.Dell.com/ Manuals /Cccomplis /powerconnect-5524_User%27s%20Guide_en-us.pdf

  Once the phone is in the voice VLAN it can still receive an IP address by the DHCP server using the DHCP relay. The switch acts as a DHCP relay agent that listens for DHCP messages,

  and passes between DHCP servers and clients, residing in IP or VLAN different subnets.

  Relay DHCP and espionage begins on page 563 of the user guide.

  I hope this helps.

• Impossible to assign the IP address for VLAN 1 (6248)

  Nice day

  I bought two layer 3 PC 6248 switches. When I try to assign an IP address by default VLAN 1, it displays an error 'failed to remove management VLAN - ID ".  These predisposees are already preconfigured with the IP address 192.168.0.1 for VLAN 1. I would like to delete this IP address and assign one in the range 10.10.1.x for VLAN 1. But this is NOT possible.

  Can someone please help me to remove this preconfigured IP, so that I can attribute my interest?

  Thanking you,

  Sam

  
  

• CM500 and CM600 public or private IP assigned to the router?

  I would like to use my router port forwarding for remote access to devices on my local network such as IP cameras. I know that with a built-in modem/router, that this can be done - I have it working now.

  Will be working with a router and a separate modem transfer port? The reason I ask, is that, in my opinion, most modems assign a private attached router IP address and not the public IP address. What I want to know is:
  1 - CM500/600 modems have the ability to assign the public IP address to a router?
  2 - port forwarding will still work when a router has been assigned an IP address private? I'm not a network expert, but conceptually the modem converts public IP + port x private IP + port x?
  3. when a router is configured to send the WAN IP of a dynamic DNS service address to send it assigns a private IP address or does it have the ability to determine the public IP address and send it?

  Thank you

  If you are on the network from Time-warner, they should assign a public IP address and for example if you connect CM500 Cable modem with a router R7000, thr router will receive the public IP address and you won't have a double NAT situation.

  I didn't know what ISP you had service with. some ISPS in Asia provides private users IP addresses, and it will create double NAT situation.

  I have not seen any ISP so far providing US with private IP addresses, but I've only worked with Time Warner and Comcasts. Not sure about smaller players.

• How to view the last element in a dynamic table 1 d

  Hello..

  I want to display the value of the last element in a dynamic array 1 d... / I mean... If I stop the vi race, I need to display the last element of the array... How can I do this?

  and is it possible to use a button to start the vi... instead of using the Run button on the face before of the vi?

  An array of index!.  Size of table allows to determine the size of your array, subtract 1, that feed into the terminal array of Index index.

  You start the VI running somehow.  It can be assigned to run when opening.  Assuming that what you want is a way to type values in a front panel, press a GO button you created on the front panel, then have the real part of the VI to run.  You can use a structure of the event.  Or put a while loop at the beginning with a small wait next statement which basically just asks the GO button.  When you press this button, the Boolean value true stops the whole loop and allows the program to move on the main body of your program.

• The ACS authentication

  We have ACS running without any problem. We have a special VLAN to a public kiosk that clients can use to surf the internet. The kiosk is wireless and is configured for automatic connection with a specific account. The access point uses the vlan 1 and vlan 40 terminal wireless. When the kiosk machine authenticates to ACS running on our domain controller (who resides on the vlan 10)-is the kiosk machine communicates with the domain controller or the kiosk machine communicates with the access point, which, in turn, communicates with the ACS server? I would like to block 40 access vlan in the vlan 10 but if the kiosk machine must communicate with the domain controller, I don't think I can. Any help is appreciated. Thank you.

  Unreliable kiosk machine only communicates with the AP. The AP will send credentials on the ACS server, which in turn, will try to authenticate them on the Windows domain controller.

• Ensure the redundancy of the ACS

  Salvation;

  What happens if my ACS only breaks down? ACS is active on my access switches.

  What deployment scenario are we talking about here? For example, with 802.1 X deployments there a function (called inaccessible Authentication Bypass) that allows you to access a VLAN specific in the scenario where connectivity to the ACS server is compromised. Is that something can help you?

• Secondary ACS authenticates not to dynamic users

  Hi all

  I have two ACS server for windows with version 4.2. My problem is that, if the primary ACS server is down, dynamic users from the database windows in unable to authenticate with the ACS secondary. Please note that if a user is added to the ACS, this user can authenticate with the windows database. Only the dynamic mapping is not the case with the second ACS server.

  A quick response will be appreciated.

  What is in the database of Windows in both the points of the unknown user policy? Dynamic users are active under the unknown user policy?

  Are these servers ACS for Windows or the ACS SE with a Remote Agent installed on a member of the AD Server?

  If they are remote Agents, see the external database > Windows Configuration > selection of the Remote Agent. The same remote Agent is selected on both ACS servers?

  Please be aware that if you change the order of the RA he would remove all your group mappings.

• Level of privilege of the ACS and sets of commands

  Hi all

  I was in charge of the implementation of 5.6 ACS in order to allow members of the groups of domain security MS Access of specific order to our equipment. I the area association and groups added, I have an access policy with a rule that works so my field trial account can connect to the switch and perform only the commands in my command set.

  The problem is that when I assign a Shell profile with privilege level 7 min/max to the rule and the user logs on with this level, they are unable to see the commands that I welcomed in the Set command. Is it possible to have the ACS to say IOS to automatically change the visible commands to a specific privilege level when the user connects, even if they are not at this level of privilege?

  Any help greatly appreciated,

  Chris Menuey

  Because you're using command authorization and restrict the user to some orders, why do we use privilege 7 and not 15?

  ~ Jousset

• Change IP of a device of the ACS

  What will break if I change the IP address of the device TO 4.2? I need a few of them to assume the IP addresses of our existing production boxes. Apart from the re-manual setting the IP SE through the console, reconfigure the AAA/replication server and the ACS Agent Config provider IPs, is there something that is "lost" permanentnly broken when you reset the IP address?

  Thank you!

  Yes, dynamic mapping is created when the user connects, but this will be a default mapping. All users will be mapped to the default group.

  Incase you have permission set up on the basis of the group, it will not run.

  If you have all the users that are not mapped to the default group, then no need to worry.

  Kind regards

  ~ JG

  Note the useful messages

• Why the ACS is blocking my connection to the Console?

  I have aaa to my SWs one routers, but wen my server goes down that I can't have access to the console port.

  My config is attached and debug aaa authorization.

  These are debugs it for each access: Telnet user, consoling Ganymede user Ganymede and testing of Pentecost the local user.

  Telnet access

  Oct 15 01:03:09: AAA: analyze name = tty2 BID type =-1 ATS = - 1

  Oct 15 01:03:09: AAA: name = tty2 flags = 0 x 11 type = 5 shelf = 0 = 0 = 0 = channel 2 = 0 port adapter slot

  Oct 15 01:03:09: AAA/MEMORY: create_user (0x2778E84) user = ruser 'NULL' = 'NULL' ds0 = 0 port = 'tty2' rem_addr'10.10.10.23 = 'authen_type = ASCII service = CONNECTION priv = 1 initial_task_id = ' 0', vrf = (id = 0)

  Oct 15 01:03:10: CDP-4-NATIVE_VLAN_MISMATCH %: incompatibility of VLAN native on GigabitEthernet0/37 (102), was discovered with tst1-s2 GigabitEthernet0/1 (1).

  Oct 15 01:03:11: AAA/MEMORY: free_user (0x28E1BFC) user = ruser 'ACS-USER' = 'NULL' port = 'tty2' rem_addr = '10.10.10.23' authen_type = ENABLE priv = 15 = ASCII service

  Oct 15 01:03:13: AAA/MEMORY: free_user (0x2778E84) user = ruser 'ACS-USER' = 'NULL' port = 'tty2' rem_addr = '10.10.10.23' authen_type = ASCII = priv = 1 CONNECTION service

  Access to consoles (work of Pentecost the ACS user)

  Oct 15 01:08:57: AAA: analyze name = tty0 BID type =-1 ATS = - 1

  Oct 15 01:08:57: AAA: name = tty0 flags = 0 x 11 type = 4 shelf = 0 = 0 = 0 = 0 = 0 channel port adapter slot

  Oct 15 01:08:57: AAA/MEMORY: create_user (0x28AA8E4) user = ruser 'NULL' = 'NULL' ds0 = 0 port = "tty0" rem_addr = "async" authen_type = service ASCII = CONNECTION priv = 1 initial_task_id = '0', vrf = (id = 0)

  Oct 15 01:09:11: AAA/MEMORY: free_user (0x27C0DC4) = user tweak "ACS-USER" = "NULL" port = "tty0" rem_addr = "async" authen_type = ASCII service = ENABLE priv = 15

  Oct 15 01:09:18: AAA/MEMORY: free_user (0x28AA8E4) = user tweak "ACS-USER" = "NULL" port = "tty0" rem_addr = "async" authen_type = ASCII = priv = 1 CONNECTION service

  Access console (not working whit the local user)

  Oct 15 01:05:24: AAA: analyze name = tty0 BID type =-1 ATS = - 1

  Oct 15 01:05:24: AAA: name = tty0 flags = 0 x 11 type = 4 shelf = 0 = 0 = 0 = 0 = 0 channel port adapter slot

  Oct 15 01:05:24: AAA/MEMORY: create_user (0x27C1310) user = ruser 'NULL' = 'NULL' ds0 = 0 port = "tty0" rem_addr = "async" authen_type = service ASCII = CONNECTION priv = 1 initial_task_id = '0', vrf = (id = 0)

  Oct 15 01:05:36: AAA/MEMORY: free_user_quiet (0x27C1310) = user tweak "LOCAL_USER" = "NULL" port = "tty0" rem_addr = "async" authen_type = 1 = 1 = 1 private service

  Oct 15 01:05:36: AAA: analyze name = tty0 BID type =-1 ATS = - 1

  Oct 15 01:05:36: AAA: name = tty0 flags = 0 x 11 type = 4 shelf = 0 = 0 = 0 = 0 = 0 channel port adapter slot

  Oct 15 01:05:36: AAA/MEMORY: create_user (0x28D201C) user = ruser 'NULL' = 'NULL' ds0 = 0 port = "tty0" rem_addr = "async" authen_type = service ASCII = CONNECTION priv = 1 initial_task_id = '0', vrf = (id = 0)

  Oct 15 01:06:09: AAA/MEMORY: free_user_quiet (0x28D201C) = user tweak "NULL" = "NULL" port = "tty0" rem_addr = "async" authen_type = 1 = 1 = 1 private service

  Oct 15 01:06:09: AAA: analyze name = tty0 BID type =-1 ATS = - 1

  Oct 15 01:06:09: AAA: name = tty0 flags = 0 x 11 type = 4 shelf = 0 = 0 = 0 = 0 = 0 channel port adapter slot

  Oct 15 01:06:09: AAA/MEMORY: create_user (0 x 2773004) = user tweak 'NULL' = 'NULL' ds0 = 0 port = "tty0" rem_addr = "async" authen_type = service ASCII = CONNECTION priv = 1 initial_task_id = '0', vrf = (id = 0)

  Oct 15 01:06:41: AAA/MEMORY: free_user (0 x 2773004) = user tweak "NULL" = "NULL" port = "tty0" rem_addr = "async" authen_type = ASCII = priv = 1 CONNECTION service

  Thanks for your help.

  Change your orders

  AAA of default login authentication group Ganymede + activate

  the AAA authentication enable default group Ganymede +.

  TO

  AAA authentication login default group Ganymede + local

  the AAA authentication enable default group Ganymede + activate

  Kind regards

  Prem

  Please if it helps!

• Strategy of the ISE, DACL and VLAN change together

  So I had a hard time finding consistency in a policy that changes the VLAN and applies to a DACL. Originally, I discovered that the remarks were causing to ruin. But I can't find any consistency. Can I use vanilla ' oermit all ' DACL to ISE, as well as a change VLAN and it just doesn't work. My AuthZ is very simple... If you are wired_MAB and your point of endpoints in a particular group, then apply a policy that changes the VLAN and applies to a DACL. This seems like it was originally what ISE is supposed to do, but it seems so buggy. Strange thing is that if I change VLAN by itself, it works. But when I add to the DACL does not work either. Anyone have any ideas why this is?

  Your main problem, will probably be with assignment of DACL, which requires the switch to know the ip address of the client, before any list DACL will apply, at least in host multi-auth mode, I know a "bug", where analysis of device does not work yet once you change your local network virtual access initial port to another virtual LAN and try to apply a DACL using the validation of the MAB When this fails, try to check your schedule of ip device, and see if you hit the same "bug" is I've touched before. You should see this device analysis think that your device still has the original investigation period vlan or none at all. Remember that DHCP Snooping is also used to fill the device-tracking table, so make sure you use it also. Other than that, you could try mode closed, but that if them run could not be suitable for your environment.

• Whence the ACS server get the DNS Info for the IP pools?

  I'm changing the DNS servers that my VPN users are assigned from the pools of IP on the ACS server. Where IP pools Gets the DNS server information. I changed the IP addresses of the DNS on windows server and rebooted. But VPN clients are always assigned the old DNS servers.

  ACS ip pools do not grow the DNS server information

  It is either transmitted from the setup of group for the VPN concentrator or

  It is to be send to the setup of the user/group ACS > attributes Radius (VPN 3000) > [026/3076/005] primary DNS.

  I hope this helps.

  Concerning

  Rohit

• Assignment of the task to its users and groups

  Hi Experts,

  We have a requirement for the assignment of the task to its users and groups. What are the different options we have to achieve this goal.

  (1) considers that I have 6 groups, 6 groups, I need to take a group and itinerary of the task to a dynamic group.

  Each group contains also 15 users when a task is routed to the Group A then all users in Group A should get the job. How can I achieve this. Can u send me please step by step procedure.

  We use Jdev 11.1.1.6

  (2) I have confusion about the roles of Parametic what exactly it is? And what is the difference between parametric and Management Chain.

  Thanks in advance.

  Pavan

  Dan, thank you so much for the post and the explanation...

  But today, I just mention its only 6 groups... but if the groups continues to increase as groups of 100 or more so how can we achieve...

  Kind regards

  Pavan

• Skillbuilders Super LOV, refresh the list of SLOV values dynamically

  Hi, another question.
  
  I have 2 SLOVs. 1 is a relative of the 2nd.
  
  The first has its value dynamically for a reason any.
  I can not then dynamically change the value of the 2nd until the cascading effect is triggered by the opening of the 2nd SLOV via the button.
  
  If the page has LOV1 with value 'A' with LOV2 have child values "A1", "A2", "A3" available and I then proceed as follows
  
  $('#P1_LOV1).apex_super_lov ('setValuesByReturn', 'B'); (where B is a valid value)
  
  followed by
  $('#P1_LOV2').apex_super_lov ('setValuesByReturn', 'B1'); (assuming that B1, B2 and B3 are values of child for B)
  
  Then, it does not work.
  
  In fact
  $('#P1_LOV2').apex_super_lov ('setValuesByReturn', 'A1');
  $('#P1_LOV2').apex_super_lov ('setValuesByReturn', 'A2');
  $('#P1_LOV2').apex_super_lov ('setValuesByReturn', 'A3'); Still work, even if the parent is now wrong.
  
  So, basically, it seems that dynamically change the SLOV parent value is not triggering of the ripple effect that manually the SLOV itself chosen.
  
  Is it possible to force the list of values for updated after change dynamically children parent cascading?
  
  Concerning
  Mark

  Hi Mark,

  Some problems with the State of session here! Your lov EMP is limited to documents that match the DEPT value in session state. Initially this will be null and no value. Suppose you select a Department and send the page, so that the values are stored in session state. When you open the lov, employees would be only those for the Department which the value is stored in session state. Understand the State of Session, Oracle docs

  You were on the right track with cascading lists, but it breaks your choice by default features. So I've ignored this output, I don't want the default functionality. We need to do our own for this. Don't worry, not too!

  Off, when dept in the default settings or dept lovs changes because of a choice, the selected Department must first go to session state. This is necessary for the lov emp can find the correct records. So I added a dynamic action to fire on the change of P14_CHOOSE_DEFAULTS and P14_DEPT. The real action is a PLSQL code execution. PLSQL is always on the server side, and we can provide items to submit to the session state. The executed code is simply

  NULL;
  

  because we don't need to run anything, but P14_DEPT has the value that will be submitted to the session state when the call is made.

  With these changes, everything works. But EMP must be blanked when DEPT changes. Otherwise, you could spend DEPT autour but are not yet in a bad EMP.
  So I added another dynamic action that fires on the evolution of the DEPT and blanks in the EMP. No worries about default values, picking, because that won't change due to values only being edited
  javascript change events that are not performed.

  PS: don't forget to assign the answer useful/correct labels to messages that are :-)