ASUS Wifi Go! Will not connect to the wireless router

Similar Questions

• HP 7520: HP 7520 will not connect to the wireless network

  There is some additional information to

  http://forums.Xfinity.com/T5/home-networking-router-WiFi/HP-7520-will-not-connect-to-wireless-networ...

  on this issue.

  Have several APs for a single wireless network allows the printer foolish law.  (Not a Repeater, a second AP connected to the local network with the same configuration of network for security, etc.).

  I solved this problem.  In accordance with the discussion on the link, the problem is that the printer cannot connect to a wireless network if there is greater than 1 for a wireless network (SSID) name wireless access point.

  This thread has had several useful suggestions, but what finally solved the problem, it's the second point has access to a mode where I can create a 'virtual' access point and, above all, a SSID associated.

  Note that not all access points or routers support virtual APs, but this function seems to be more common over time.  Older models is not able to do that.  However, a new access point is sometimes cheaper than a new printer.

  If you do not understand the jargon in the procedure below, I recommend that you find someone who does, then they can do it for you.

  Solution:

  1. On one of the wireless access on the network, create an a new virtual AP with a slightly different name SSID (for example < name of the network - > _1), on the same VLAN (usually VLAN 1).  You may need to put the AP in "multiple AP mode" or something similar, and then restart the AP.  All other settings (DHCP, security, mixed mode b/g/n, etc.) must be the same for the new SSID.
  2. Run the printer Wireless Setup and connect it to this new SSID
  3. Confirm that the printer can be seen by other devices on the network

  Tips:

  • Check the security is the same as the original SSID, Alternatively you can create a vector of insecurity in your network.  Do not WEP-128 when the other SSID uses WPA2 AES, for example.
  • The AP I had had several resets to make it work because of the mode and parameter changes.
  • If you connect the SSID but cannot connect to or be seen by anything on your network, check the new SSID/AP is in the same VLAN as the original.
  • Because the printer is not roaming, and the speed is not a problem for me, I used the access point that could support this solution, which is deeper and slower than my primary AP.  I have not noticed any problems.

  The printer has been reliable on the wireless now on the new SSID, 48 hours.

  I have not upgraded any software on a client of the printer (PC, Mac, phones).

  I think that it is a positive confirmation that the problem is with the implementation of the printer of the stack of network and not with the driver or client software on remote devices.  The 802.11 protocols provide for a network name (SSID) wireless with several access points using different MAC addresses.  I suggest this HP look into this as a potential bug with their network printer for the 7520 protocols stack.

• HP Officejet 6500 a: printer will not connect to the wireless network.

  I got this HP printer for a while and it worked fine.  Our old router is out and we had to get a new one.  Installed perfectly and printer continued to work properly.  The password for the router was ridiculous, that's why I changed it to something much more simple to remember.  Since then, my printer will not connect to wireless internet.  I have a ~ and reinstalled the printer but still have the same problem.  I thought maybe to try the former password would, but who does not work either.

  Anyone has any ideas that might help before chuck it and go and get a new one altogether?

  Thank you.

  Easy things first.  Turn off the router and the printer.  Turn on the router and wait 3 minutes.  Turn on the printer and see if it connects to your router.  Status?

  If no joy, temporarily disable all security in the router.  Now try to connect the printer to your SSID not guaranteed without password.  Status now?

  If OK, go back and add WPA2-AES with your simple password.  Status now?

• no internet but not connected to the wireless router

  I have 400 SL with windows vista installed.
  Everything worked well for years, until a few days ago.
  It is the symptom, and what I've done:
  1. the laptop CAN connect to the wireless network, no problem, very strong, just signal has no internet.
  cannot ping google.ca.
  In network and sharing Center:
  Computer---> network---> Internet
  ^                   ^
  |                     |
  Red Cross OK
  2. all other devices (iphone, ipad, other laptops) can connect to the network and internet.
  3 did a system restore on the eve of this stoppped working. always the same.
  4A bought a wireless adapter, always the same. but it works fine on the other laptop
  5 tried to set a static IP, subnet mask, gateway, still the same problem.
  6. any other device can ping each other with the exception of this laptop...
  7. the seller cordless tool is uninstalled (Lenovo connection management tool)
  8 rebooted a million times between all the steps
  9 safe mode with network has the same problem.
  10 tried to use other wireless, still the same problem...
  need help...
  Thank you
  -Virginia

  Hi Virginia,

  Thanks for posting your query in the Microsoft Community Forums.

  After the description of the problem, I understand that you can not connect to a wireless network on windows vista computer.

  I appreciate your efforts on this issue, however no need for you to worry we are here to help and guide you in the right direction.

  Help me with the information below.

  -Don't you make changes on the computer before this problem?

  I suggest you to disable temporarily security software and then check if you are able to connect.

  Method 1

  You can also temporarily disable the security software and check if it works.

  http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-Firewall-on-or-off

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  If disabling the security software solves the problem, then contact the manufacturer of the specific security software to fix the problem.

  Important: These steps may increase your security risk. These steps may also make the computer or the network more vulnerable to attack from malicious users or malicious software such as viruses. We recommend the process that this article describes to enable programs to operate as they are designed for, or to implement specific program features. Before you make these changes, we recommend that you evaluate the risks that are associated with implementing this process in your particular environment. If you decide to implement this process, take additional measures to protect the system. We recommend that you use this process only if you really need this process.

  Method 2

  Reset the router and see if that helps.

  Note: to help you reset the router, you can consult the manual that came with the router or the router contact manufacturer.

  You can see this help article.

  Wireless and wired network problems

  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-Vista&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Hope this information is useful.

  Let us know if you encounter problems under windows in the future. We will be happy to help you.

• B210A Photosmart - server connection error and does not connect to the wireless router

  I have problems setting up and to connect my router to my new printer b210A. Everything goes well with the initial configuration, and when asked to connect to the network at the start, it works. Then he said that the printer requires updates, downloads of updates, reboots, asks me if I want to activate eprint and as soon as I said 'Ok', I get a "the server connection error" and it is then no longer connected to the network. When I get out of the "server connection error" screen and attempt to reconnect to the network, he says 'Success', prints a Test report wireless, but never connects.

  It's the 2nd printer that I have had in a week, given that the person of HP online chatting told me my first printer had problems of "hardware", after experiencing the same problems and I'll be recommended. So - I did, and now I'm running into the same issues. The number of 800 was NO HELP - after recommended I have unplug and reconnect, then telling me there were server errors (when the printer was not connected to the network).

  We will set an IP address of the printer with a special focus on DNS domains:

  -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
  -Enter the IP address in a browser to reveal the internal settings of the printer.
  -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). You can find the beach DHCP from the router using its internal settings page or in its manual. Use the CD that came with your router or type the IP address of the router (ends para.1) in a browser.
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Enter the IP of your router (on the Page of the Network Config) for the gateway

  -For the first DNS 8.8.8.8 and 8.8.4.4 for the second use.
  -Click 'apply '.

  Now, stop the router and printer, start the router, wait, and then start printing.

  After that, you will have to redo 'Add printer' using the new IP address.

• Laptop will not connect to the wireless network

  I have a Toshiba laptop with windows Vista, and it does not connect to wireless internet at my father's House. My father and my sister have the same exact computer, and both of their computers work perfectly well. Mine will work with an ethernet cable plugged in, but when I try to connect wirelessly, it does not work. I've never had this problem in my mom's house or anywhere else. Can someone help me please?

  Hello

  This is a security feature of each wireless router I've ever seen, although I wouldn't be surprised to discover that some router didn't do it. You need to check your router admin pages to see if mac address filtering is in effect. Address filtering Mac prohibits access to the router by any unauthorized network device. All network devices have a unique mac address which you can find through opening a command prompt (click Start, then type cmd and press enter) and then typing ipconfig/all. The output refers to your device Wireless 'physical address' (mac address) and will be in the format hh-hh-hh-hh-hh-hh, where hh is a hexadecimal number (A - F and numbers 0-9), dashes are not important and may not be required when you enter your mac address in the router configuration.

  Tricky

• Photosmart 5524: Photosmart 5524 will not connect to the wireless network

  I recently moved house, and since the move does not connect the printer to the network.

  The router and the parameters are the same as before the move, and appliances are on opposite sides of the same coin.

  Initially, he sees the network, but does not connect when you press the WPS button or the password.

  After the first attempt he cannot see all networks at all until the settings are reset, even if the network name is entered manually.

  Printed on the test result to get a 'Pass' for YOU wireless and WIRE WORKS, a "failed" to FIND NAME of NETWORK and "Not run" on all other tests. The proposed solution is not useful, as it suggests using the Wireless Setup Wizard to set up the printer, which I already do.

  No other device has problems see the network or connection to it. MAC filtering is not lit. Some devices have a static IP (required to stop Ipad wife being a tyrant of intellectual property), but the router DHCP is still active for most devices.

  Temporarily remove your SSID of your router password. Now try to connect to your SSID unsecured. Are you successful? If so, go back and add WA2 - AES with a password and try again.

• ENVY 4520: printer will not connect to the wireless network

  with wireless on Printer Setup Wizard, printer detects the network but when I enter the key to encryption (correctly), he comes back with a message "Unable to connect to the network".  The printed report suggests the address filtering MAC can be activated.  But I checked and it is specifically DISABLED.    The printed report indicates a FAILURE on "no filtering."

  Please notify.

  After struggling with this for two days and after the announcement of this question and all by downloading the HP doctor, I noticed that the printer had suddenly cured himself. I'm not sure what I should credit this miraculous healing. Thank you I guess?

• NB300 will not connect to my wireless router

  Can someone help me please?

  I have an old week NB300 laptop computer that has a built in Atheros AR9285 wireless network adapter.
  I have problems connecting to my D-Link wireless router/AP.

  None of my other wireless products have connection problems, and it is only this laptop that won't.
  I have reset the modem/router, I unplugged the adapter wireless in Device Manager and updated drivers.

  We can see broadcasting and all other my neighbours routers, but just used to connect.

  Any suggestions out there?

  Hello

  You mean NB300 can see your WLan and other WLan in the neighborhood, but cannot connect?

  This would mean that the WLan is enabled correctly because the WiFi network around you are visible
  In any case, check if you have enabled the WLAN using the FN + F8 key.

  In addition, you should go to the properties of the wireless network and need to check the TCP/IP protocol. Disable the IPV6 Protocol and use only IP v4

  In the properties of the TCP/IP Protocol, you should check if all options are set to automatic.
  MAC address filtering, no encryption, encryption password must be checked as well!

  By the way; Here you will find the latest Wlan drivers:
  http://APS2.toshiba-tro.de/WLAN/

  Welcome them

• Aspire laptop will not connect to the wireless printer, he said: he can't communicate with the printer

  I have a laptop sucks and when we first put in place it would print to the printer wireless, but now he says that he cannot communicate with the printer. I know just enough to get me in trouble with computers. Any suggestions?

  Hello

  I imagine the inconvenience that you are experiencing. I'll certainly try and help you in the matter of fixing.

  To help you to propose measures to solve the problem, I would appreciate if you could answer the following questions:

  1. which version of the Windows operating system is installed in the computer?

  2. you have any security program installed on the computer?

  3 are you aware of any changes made to the computer before the show?

  If you use Windows 7, then I suggest you to go through the steps in the link and check.

  Hope this information was helpful and let us know if you need more assistance. We will be happy to help you.

• Satellite L40 - 14N does not connect to the WLan router

  Bought two portable Satellite L40 - 14N as Christmas gifts and one of them does not connect to the wireless router.
  Is the error that says "error message unknown" try please login again.

  The wireless network appears in the list of networks available with a strong signal. Notepad attempts to connect but the error 'wireless link failed for an unknown reason. " Made a comparison with the other laptop that works very well and the configurations appear to be identical!

  Tried it on wireless network from a friend with the same result. All suggestions, am pulling out my hair at this point.

  Seems to be a Vista issue.

  I found this article Ms knowledge base:
  http://support.Microsoft.com/kb/928233/en-us

  You need to add a value in the Windows registry.

  1. Click Start, type regedit in the search box, and then click regedit
  list programs.

  2. Locate and then click the following registry subkey:
  HKEY_LOCAL_MACHINE es\Tcpip\Parameters\Interfaces\ {GUID}
  This registry path, click the (GUID) subkey that corresponds to the
  Network adapter that is connected to the network.

  3. on the Edit menu, point to new, and then click DWORD (32-bit) value.

  4 new value #1, enter DhcpConnEnableBcastFlagToggle, then
  Press ENTER.

  5. right click on DhcpConnEnableBcastFlagToggle, then click on modify.

  6. in the value data box, type 1 and then click OK.

  7. close the registry editor.

  concerning

• I received a message on my laptop computer that says not able to connect to the wireless router.

  I received a message on my laptop that says could not connect to the wireless router and it make reference to section of the knowledge base Microsoft 87112 for more information.

  I think you have transcribed the number incorrectly.  I think that the article you want is this one: http://support.microsoft.com/kb/871122

• SK2061: The wireless keyboard will not connect when the PC is turned on.

  My problem is, when I start the PC, (HPK-15 500, 319NA), wireless (SK2061) keyboard, does not connect. I have to shut down the PC so he can connect (no restart, you must stop it).  Have had the PC for 5 months and it has been published. Not changed the battery makes no difference.

  The internet statement States I shoud push the blue button until the USB receiver flashes. This PC does not have an external USB receiver, I guess it's built in! The mouse works OK.

  Hello @JimCar82,

  I read your post on how the wireless keyboard will not connect when the computer is turned on, and I'd be happy to help you in this case!

  Re-connect your keyboard to your desktop computer wireless, I advise you to follow the steps described in this document on the keyboard and wireless mouse troubleshooting. The USB receiver should be found at the back of the tower.

  Please re-post with the results of your troubleshooting, and I look forward to your response!

  Concerning

• Lexmark printer will not connect to the router

  Original title: HELP

  I switched to Fios and now have a new modem/router and I don't know how to get my Lexmark printer to recognize. How can I solve this problem?

  Hello

  Thanks for posting the question in the Microsoft Community!

  The Lexmark printer will not connect to the router/modem.

  Because the problem is with the Lexmark printer cannot connect to the router, I suggest contact you the Lexmark support team in order to get help with this question.

  You can try to get help on the site:

  http://support.Lexmark.com/index?page=productSelection&channel=supportAndDownloads&locale=en&UserLocale=en_US

  If you need any help or if you encounter problems with Windows in the future, let us know and we would be happy to help you.

• Why Vista will not connect to the internet wherever I'm connected with my XP machine?

  Why my computer won't get online wherever I like Xp only

  Why Vista will not connect to the internet wherever I am?  I thought what to see that there is a link to a site to repair this, but when I found the site the link had disappeared.  Thank you

  Hello

  1 are you facing issue while trying to connect to public Wi - Fi hotspots or private home network?

  2 have you tried all of the suggestions of Fahimulla K?

  I suggest you to go through the steps mentioned in the link and the Coachman.

  Solve problems, find wireless networks

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-finding-wireless-networks

  See also:

  Wireless network card: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows-Vista/wireless-networking-frequently-asked-questions