automatic configuration - please wait constantly rises

Similar Questions

• Configuration automatic please wait blinks on the screen every few seconds, why?

  Whenever I start my computer a small window with the text "Auto Config please wait" flashes in the center of the screen every two seconds. This continues for a few minutes. After that he produced intermittently, but each time that it the screen dims and for a few seconds, I am unable to do anything either, no key or mouse fills it. Any suggestions? I scanned and repair errors and defragmented

  Hi YvetteBarnes,

  1. did you of recent changes on the computer?

  2. What is the version of Windows installed on the computer?

  3. What is the number of brand and model of the computer graphics card?

  The error message occurs generally if there is a problem with the monitor adapter or graphics on the computer.

  Method 1

  I suggest that you change the resolution of the screen on the computer and check if the problem persists.

  Change your screen resolution

  http://Windows.Microsoft.com/en-us/Windows7/change-your-screen-resolution

  Method 2

  If the previous step fails, then you need to update drivers graphics card on the computer manually by visiting the card manufacturer's Web site and check if it works.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  If the problem persists, then connect another monitor to the computer and check if it works.

  I hope this helps!

  Halima S - Microsoft technical support.

• Error: "Please wait while Windows configures Microsoft Office 2000 Professional.

  How can I get rid of the message "Please wait while Windows configures Microsoft Office 2000 Professional".  Apparently, the system does not find a valid source for this.  To my knowledge, I have not downloaded this software even though I must admit that it does not appear in my list of software.  I tried to remove the screws of the Panel control, but to no avail.

  Thank you for your response.  I have now solved the problem by deleting the installation, using the cleanup utility.

  However, I appreciate you trying to help me.

  Annie876

• When opening Legacy Family tree, I received a message "Please wait while windows configures DAO. Then "error 1706. No valid sources were found for the DAO product.

  "Error 1706.

  When opening Legacy Family tree, I received a message "Please wait while windows configures DAO.  Then the message "the feature you are trying to use is on a network resourse which is not available. Then "error 1706. No valid sources were found for DAO product. "  I uninstalled Legacy and reinstalled, but the problem persists.

  Heritage it's a windows problem.

  try to run a file system Checker

  Start-> Run-> cmd
  In the prompt, type: SFC/scannow
  The scanner

  Reinstall the product

• Please wait while Windows configures FAX"... this process stops and I get another message that says:"the component you are trying to use is on a CD-ROM or another removable disk that is not available. "

  Original title: widows installation problem

  I have Windows XP Professional running on a desktop older.  I cleaned the disk and I would use it only as a 'internet '.  It works well and response times are pretty fast, but when I connect I get a box that says "Please wait while Windows configures FAX"... this process stops and I get another message that says "the component you are trying to use is on a CD-ROM or another removable disk that is not available", "put the 'FAX' disk and click OK. , "" Use Source: '1' "»

  The first question is I do not use a fax application and never did, I have tried every disk I can think of to complete the process, but I get the same message with each one 'the path '1' is not found. "Make sure you have access to this place and try gain or find the installation 'FAX, MSI' package in a folder from which you can install the FAX product." .. then "error 1706 - FAX." Valid any source not found for the FAX product.  Windows Installer cannot continue. »

  This will take place two or three times at the beginning upward.  How can I prevent Windows Setup tries to install something that I do not use or do not seem to have?  I deleted any fax program, that I could find on the computer, and nothing seems to work.

  Hello

  1. have you done any change in software on the computer lately?
  2. are you able to install other applications and programs successfully?

  Check to see if the problem exists in Safe Mode, if the computer works as expected in mode without failure, then we can solve the problem in the clean boot state. There is an application which is set to start when you start the computer and which launches the installer of Windows.
  a. refer to the article below for the procedure safe mode in Windows XP
  A description of the options to start in Windows XP Mode
  http://support.Microsoft.com/kb/315222

  b. you need to perform a clean boot to find the program that is causing and then disable or remove.
  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353/en-us
  Note: When you are finished troubleshooting, follow the steps as explained in the article to reset the computer to start as usual.

  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Please wait while windows configures the microsoft broadband network

  Whenever I turn my laptop on a Microsoft Broadband Networking window appears saying "Please wait while windows configures microsoft broadband networking" and then the green status bar stops about 1/3 of the way and if I try to open any programs that everything freezes.  Can anyone help!

  (Moved from other/unknown)

  Please provide more information.

  1. what version of windows is installed on your laptop?

  2. is there an error message that you receive after the failure of the MSBBN Setup?

  I suggest to update the firmware of the Device MSBBN, follow the steps in this link.

  https://support.Microsoft.com/kb/814445?WA=wsignin1.0

• RVL200 displays "system busy! Please wait... ' when loging in to the configuration page.

  Had an IPSec tunnel with a RVL200 at each end for well over a year.  Lately the problems started with one of them.  Attempts to open a session configuration pages (locally or remotely) or a VPN translates the message "system busy! Please wait a minute for re-login RVL200".  Finally the RVL200 lock.  Cycling the power unit is the only way to restore normal operation.  Any ideas what can cause this?

  I think the firmware may be corrupted. Try to reflash the firmware. Then do a hard reset and reconfigure the device.

• Receive message "Please wait while windows configures the status" and then "the component that you are trying to use is on a CD Rom, please insert". I don't have the CD. How can I stop this?

  Windows Setup status

  Whenever I start my computer, I get a series of pop-up boxes that talk about "Please wait while windows configures the State" and then the one that says "the component that you are trying to use is on a CD Rom, please insert".  I have no idea what it is, and I have no disc to put on this line?  If I hit the buttons cancel these boxes enough times to go, but it's annoying and there is notihing badly with the operation of the computer, after I get rid of the boxes.  No idea how to stop this from happening again?  I did all the steps that have been mentioned earlier and no results.  I even did a system recovery.  I don't know what to delete.  Please help thanks

  Hello

  These messages usually mean that you have a problem with the HP printing software

  Contact HP

  http://welcome.HP.com/country/us/en/contact_us.html

  Contact HP options at the link above.

  http://h30434.www3.HP.com/

  HP's Support Forums at the link above.

• Get a message saying "Please wait while windows configures spare back upward.

  Attempt to add a new "all in one". Get a message saying "Please wait while windows configures spare back upward. When I hit OK it gives another box saying "the component you are trying to use on a network resource that is unavailable, type a different path to the folder containing the installation package in the box below". It was certainly around in circles. What should I do? The two boxes are subtitled "backup alternatives."

  Hello

  "all in one"? Printer?

  Contact the manufacturer of the printer for assistance with this

  their Web sites usually have available installation instructions

• "operations are underway. Please wait. The machine switches off automatically '-system never stops.

  Sometimes, when to stop Vista, instead of a normal shutdown, I get quite common background and a message reading: "operations are underway. Please wait. The machine switches off automatically. "The system then continues to run indefinitely, and I finally have to do an emergency stop. After the reboot, I then most of the time have to do a restore to an earlier point; Once in a great while, he'll tell me the test stops abnormally and charge really. Tried to figure what could be causing it and can't find a logical reason. Diagnosis never found anything, but there is not really anything in the windows which diagnosed something as a shutdown of the system.  Help.  It's boring.

  Hi Baron Stewart,

  (1) since when are you facing this problem?

  (2) remember to make changes?

  Method 1: Disconnect all external devices (printers, scanner, USB (universal serial bus) readers, etc...)  Except the mouse and keyboard and then try to stop

  If this solves the problem, then add back devices at a time until you discover the piece of hardware causing the issue.  Then get any drivers\software update for the device.

  Method 2:  Select the boot and then check if the problem persists

  Follow step 1 in the link below,
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  If everything works well after a clean boot, you can deduce that some third-party services are at the origin of the problem.

  Continue with the remaining steps to pin-point on the third party service.

  After find you the program that is causing the problem, you will have to perhaps to update or install a newer version of the program, if you rarely use that you should consider uninstalling the software.

  
  Important: n ' forget not to put the computer to a normal startup follow step 7 in the link.

  Method 3: check the logs in Event Viewer for more information on this problem

  Open event viewer

  What are the information in event logs? (Event Viewer)

• Please wait while Windows configures your computer every time at startup

  Hi guys,.

  I was recently infected by a virus, it has been removed and it corrupted the registry beyond repair, I backed up my files and re-installed my Windows Vista Ultimate 32 - bit edition, everything is all back and work, with the exception of this little problem...

  Whenever I start my count, after the green bar loading screen, it is a black screen saying

  "Please wait while Windows configures your computer...". »

  It takes about 5 minutes, then continues to the desktop very well, it's just that I prefer there not to go to the black screen and take 5 minutes every time I start up.  I have installed all updates, including Service Pack 2 and still no joy. Anyone know what is this problem and how to fix it?

  Thank you

  Chris

  Hi temple3188,.

  Try the troubleshooting steps in this thread, described by Michael, to solve your problem.

  Dena
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• On startup, I get the message: Please wait while Wilndows configure installation package 'Destination' Destinations.msi.

  Original title: Windows Installer

  Whenever I reboot Windows Vista Home Premium, I get the following events:

  Windows Installer opens and then I get the following

  Please wait while Wilndows configure installation package 'Destination' Destinations.msi.  I have no idea of what is Destinations.msi and that you have never installed such a program.  He asks me to put in the cd disk that comes with the program.

  Any suggestions on how to stop this very annoying interference every time I restart my computer.

  Thanks in advance for your suggestions and help.  HankL

  Hello
   
  Method 1.
  Let us run Disk Cleanup and then reregister the Windows Installer service and check.
  Stage I.
  a. open Disk Cleanup by clicking the Start button. In the search box, type and then disk cleanup in the list of results, click Disk Cleanup.
  b. in the drives list, click the drive you want to clean, and then click OK.
  (c) in the dialog box disk cleanup, on the Disk Cleanup tab, select the check boxes for the types of files that you want to remove, and then click OK.
  d. in the message that appears, click on delete files.
  For more information see the link below:
  http://Windows.Microsoft.com/en-us/Windows7/delete-files-using-disk-cleanup
  
  Stage II.
  Unregister Windows Installer and then reregister Windows Installer. To do this, follow these steps:
  a. in the menu 'Start', click on ' execute:.»
  b. in the "Open" box type "msiexec /unreg" and then press ENTER.
  c. on the menu 'Start', click 'run '.
  d. in the "Open" box type "msiexec/regserver" and then press ENTER.
   
  Method 2.
  At startup, there is a request pending to be updated or installed. We can perform the boot minimum troubleshooting to find this application.
  See the article below for instructions on how to start your computer in a clean boot state.
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  Note: When the diagnosis is complete, don't forget to reset your computer to normal startup. Follow step 7 in the above article.
  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• "Please wait while windows configures your computer."

  Hey guys, I was stuck on the screen saying "Please wait while windows configures your computer" for about an hour. I'm running on a hybrid of studio 140 g and eject my disk is defective, so I can "eject the disc. Is it possible to restore the computer settings to factory through the start menu or anything that does not require access to the office.

  Thanks in advance

  My warranty is over, then Dell will be in charge of me, and I think they're going to charge me a price pretty hefty for a minor problem.

  We cannot help that your warranty has expired.

  Hardware issues are beyond the scope of these Forums.

  And report problems with the DELL for DELL recovery process, NOT Microsoft...

  http://support.Dell.com/support/topics/global.aspx/support/DellCare/contact_technical_support

  Contact Dell at the above address

  Good luck with it.

  Mick Murphy - Microsoft partner

• Product configuration... Please wait and then nothing!

  Hello

  I had my HP LaserJet MFP M175 np 100 for nearly two years.  It has been implemented for almost the same two years without problem.  Recently, I tried to add two new laptops to wireless and the majority of wireless laptops connected started having problems printing.  In addition, all the IPAD is connected to the wireless printer could no longer find the AirPrinters printer.

  So I tried to uninstall the driver of any PC laptop, so that I could start over completely.  Now I'm trying to place the main laptop on the connection and when I install the driver with the CD for the printer comes with, it goes through all the steps up to 'Install '.  When he arrives to install and has written to connect to the printer and the PC, I connect the laptop via USB, and then the login step 100%.  The next screen says "configuration...". Please wait "."   Then the meter never passes 15% and wrote the error message that appears: "unable to communicate lease to ensure that your PC and the product are connected via the USB cable and that the product is on and ready."

  Many times I reinstalled the software I've never had this constant message.  I tried on another laptop and it still gave me the same message on that one.  Can someone help with this error message?

  Help, please!

  Thank you!

  Hi @ChristiC ,

  I understand that you cannot set up the printer on the wireless again. I can help you today.

  If the printer is in an error state, it will not be recognized on the computer.

  Power cycle the printer.

  Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector) This ensures that the printer is full on and can help this situation.

  Restore the default settings of the network printer.

  • Press the Setup button. (key)
  • Select the network configuration Menu.
  • Then select default settings.

  Print a configuration report to ensure that the IP address is 0.0.0.0 and the SSID is disabled.

  Go to the install button (key) on the printer, arrow to the reports on the right, select config report.

  Check Device Manager to see if the USB printing support has been installed for the printer or with the name of the printer, under Bus USB controllers. How to make in the Windows Device Manager?

  Let me know how the printer is listed, or if you have exclamation points.

  If you have an exclamation point on the printer, right click and update the printer drivers.

  If the pilot will not be updated or you have a composite USB or an unknown device, try and update the driver, if it will not, right-click and delete the entry.

  If the printer is not listed, or would not be updated, unplug the USB cable and run the uninstaller from the CD.

  I disable all the start up programs and temporarily disable the Antivirus software to see if there is a program to interfere in the background. How to use MSCONFIG. Click the Startup tab and click Disable all.

  Then download, save and run the latest drivers. Drivers HP LaserJet Pro 100 color MFP M175nw.

  Test the printer.

  Then you need to go back and enable startup programs and turn on the Antivirus software.

  What operating system you use on computers? How to find the Windows Edition and the Version on your computer.

  Please provide detailed results if you're still having problems.

  Good day!
  Thank you.

• UCS 200 M1 power Hang @ 'configuration and test of memory, please wait... »

  Hi all

  I am new to the solution of the UCS and tried recently updated the BIOS via the host update utility and MMIC. There were a few warnings version that prevented the upgrade, but I was able to update the firmware of the NETWORK adapter.

  CIMC is at version 1.0.2 and BIOS at C200.1.4.1.0.071320110702.

  I'm not sure how to read the version of the BIOS however.

  When the server is turned on, there are 3 long beeps and it crashes to the configuration and memory test, please wait...

  In any case, I am tired of the BIOS recovery procedure using the J1E5 jumper without success.

  If anyone has experienced this?

  Thank you in advance.

  Calvin.

  Host upgrade utility is not supported until version 1.2.

  This may have been the cause of some of your upgrade issues.

  You run a BIOS of 1.4 to what I see. You will need to update your version MMIC for version 1.2 and the. Use the HUU to 1.4

  Sent by Cisco Support technique iPhone App