B209a-m not connected via USB - but it is! Grrrr

Similar Questions

• HP officejet 6500 e709n NOT connected via usb to a pc running windows xp

  I have a hp officejet 6500 e709n connected via usb to a pc running windows xp.  It has stopped printing.  I tried to uninstall and reinstall the printer software.  Now, when you try to install, I get the screen of "connect your device now' which indicates that the printer is not connected.  I've tried different USB ports on the pc with the same result.  Has anyone else encountered this situation?

  Uninstalled and reinstalled several times and finally got running again.  This can be closed.

• Printer will not connect via USB

  HP lj1022 printer will not connect not not via the USB port after the installation of the new driver upgrade hp lj1020/1022 for Windows 7 (64-bit). Driver seems to install properly until the moment where he is asked to connect the USB cable. Then he hangs up. HP lj 1020 printer appears in the display to the dashboard as the default printer. Computer recognizes the printer as hp printer lj1022 but in another "device not specified Panel when and only when the printer is on and the USB cable is connected." When printing, nothing ever comes from queue.

  Diagnosis is only that something is stuck in the queue and remove the task from the queue, but does not. Diagnostic shows no problem.

  The lj1022 printer accepts data from two other computers, as well on Windows xP and using the same cables. Three other USB ports have been tested on the new Windows 7 computer without results. The USB ports on the Windows 7 computer accept keyboards, mouse and flash memories wireless dongle without problem. The Windows 7 computer also sends data to a printer wireless with no problems.

  Hi Rmhodgson,

  Run the following utility below.

  http://support.HP.com/us-en/document/c02073861

• Printer will not connect via WIFI

  I'm continually offered an update for my CANON MG3250 printer, I've now had 8 in the past two months, and all were successful. Now my printer doesn't work! that is, it does not connect via WIFI, but will work on cable? All ideas/solutions please.

  Hello Nigel,

  Thank you for your response.

  I'm sorry for the late reply.

  I appreciate your time.

  I suggest you to refer to this article and check.
  Reference:
  Solve printer problems
  http://Windows.Microsoft.com/en-us/Windows/printer-problems-in-Windows-help#fix-printer-problems=Windows-8&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1

  Please keep us updated.

  Thank you

• The airport will connect to the brother 2270DW via USB but not ethernet

  Apple replaced my Airport Extreme after only 9 months and it has been quite a challenge to get back to square one.

  On the older airport, I connected to my printer wireless Brother via an Ethernet port on the router, but now it does not detect the printer. I changed the cables without result. I have finally connected via USB to the airport and wireless printing is restored, but why didn't he see my ethernet port.  The port works because I am connected via a cable to my laptop and it lights up. I have a problem with the port or printer?

  He does not see my printer via ethernet. What gives?

  Thank you

  Alexander

  You have entered the system preferences in printers and Scanners and added to the printer?

• D1370 "Scan type not the Remote Scan value... "Why this error when connected via USB

  Printer D1370 MF w / usb on win7 x 64 machine connection.

  I understand that when networked, I owe to the printer and manually press , then then before you scan using the software MF Toolbox on my PC and then must go to the printer once the scan is complete and cancel this setting manually before I can print or use other functions. What is total pain BTW...

  However, I also have a MF6530 and can scan directly from MF Toolbox without manually change the setting of the printer when connected via USB.

  So, I would like to connect one of my PC via USB for scanning to eliminate the requirement to manually configure the printer for the mode. But, when I do this I always get the error "type of analysis is not defined for [Remote scanner] on the device" even though I am connected via usb.

  1. I do something wrong when I try to scan via a usb connection that causes the error "remote scanner?

  2. that this has something to do with D1370 being a network printer. My MF6530 isn't a network printer.

  3 is there a manual for the software MF Toolbox? The manual on the installation disc is for 'Send email' and 'Store to Shared Folder. The manuals provided in the box do not address MF Toolbox. There must be a detailed operating manual provided by Canon for this program?

  4. What is the error Code 162,0,0?

  5. where is the complete list of the error codes for MF Toolbox.

  6 help!

  Hi monza.

  I know that this issue is frustrating and I'll be happy to help you.

  The new imageCLASS machines are designed so that you can select an option to scan the machine.  There is no way to set a default scan on this computer option.  You will need to select [Remote scanner] or [computer].  This is to ensure that your device correctly handles the scan project.  For this reason, the ability to program a specific mode is not available.

  Although an extra step to make, an advantage to choose the mode desired for a respective scanning can ensure that poor communication of scanner does not occur if it was programmed to a different mode.

  The 162,0,0, the error indicates the Toolbox does not detect the scanner mode "Remote Scanner.  Scanning is not supported with a connection on the USB hub, as the hubs can cause communication problems, trying to transmit data to the computer.  We recommend a direct connect between the printer and the computer.  Once you have connected the printer directly, perform the following steps and check if you receive the same error 162,0,0:

  1. Check that the MF Toolbox is closed on the computer and press the [SCAN] button on the printer.
  2. Select [Remote scanner], then press [OK].  The display reads, "remote scanner. Waiting in line... ».
  3. On the computer, open the MF Toolbox and select [PDF].
  4. Click the [START] button green on the window [PDF].  The machine begins to deal with the scan.

  Then I recommend to download and install the e-manual for the device to your computer.  It gives very detailed instructions on each of the functions of the machine.  The e-manual should be included in the manual on CD-ROM supplied with the machine.  If you are unable to access it from there, please click the link below to download the electronic Handbook:

  imageCLASS D1370 - Brochures & manuals

  I hope this information is useful for you.  However, if you need more assistance, please contact us at 1-800-OK-CANON (1-800-652-2666).

• Trident video capture card connected via USB 2 not working not properly under XP

  I use a Trident card connected via USB 2.0 video capture and I had a weird behavior:

  -sometimes not detected (not included in the list of devices)

  -sometimes not recognized (unknown device)

  -sometimes not start (Code 10)

  -sometimes works very well

  I used a USB Tracker to study the issue and found out that the usbehci driver is not able to activate the USB port.

  The message sequence is as follows (when it works):

  Get the status of the Port (4) - success

  Serial Port (4) feature, Reset - success

  Get the status of the Port (4) - success

  | - Port is enabled

  This is when it does not work:

  Get the status of the Port (4) - success

  Serial Port (4) feature, Reset - success

  Get the status of the Port (4) - success

  | - Port is NOT enabled

  Function Clear (4) Port, connect to state change - success

  Get the status of the Port (4) - success

  Serial Port (4) feature, reset the change - success

  I have more tracks, but I don't know if this is the right place to post.

  Thank you in advance to anyone willing to help me.

  Sincerely

  Andrea

  * original title - device USB not recognized or not started or sometimes work *.

  This link might be useful for:

  Advanced troubleshooting tips for General USB for Windows XP problems

• HP LaserJet 1200: HP LaserJet 1200 connected via USB to the PC with Windows 7 is not redirected in DRC

  Hello.

  HP LaserJet 1200 connected via USB to the PC with Windows 7 (32 bit) and works fine (latest drivers via Windows Update installed).

  But when I have connected via RDC (Remote Desktop Connection) for PC with Windows XP and try to print from this PC to LJ1200 - it is not redirected in a remote desktop session and I did not see in printers and Faxes folder.

  Other printers from PC with Win7 works fine via DRC (XPS Document Writer and PDFCreator).

  During this time when I do the same thing from another PC with Windows XP, LJ1200 (connected via USB to the PC) works very well through the DRC.

  Anyone know how to make LJ1200 to be redirected in a remote desktop session?

  Thanks in advance.

  For more information, here are 2 possible solutions:

  1. put two computers in the same workgroup and then share the printer and install from the remote computer.

  2. best solution: install on PC with Windows 7 drivers for Windows XP (PCL6) - it works very well as a redirected local printer via DRC!

• Windows 7 will not recognize or sync Pocket PC which is connected via usb

  Hello

  I am trying to sync my Pocket PC data (Pal my ASUS a686) on my computer (Windows 7 Enterprise). I think that if you had Windows XP, we would use Active Sync. However, it's windows 7, so I think that I use Windows Mobile Device Center. In fact, I used the center of the device before, but it has been a week to try to download the data again and it no longer works. He is very picky. But we need our data and cannot wait for the day that he decided to download.
  So I uninstalled the center of the device (the tip of a chat room) and now I can not re - load it. However, before I even uninstalled, the problem returning to the top, it was my computer does not recognize the device connected via usb.
  Code 43 continues to come does not recognize this device. And yet it is plugged. I keep trying to restart, plug the unit in different orders, send good energy, etc.
  I did a soft reboot of the pocket pc the last time, but that makes you lose all data on the pocket pc and we cannot lose this data. Finally, it is for the eco-counter software. When it worked, I hit the sync button and the data were downloaded. Now... He says just connect me please my pocket pc when it is connected. Why!
  Thank you
  Cole

  On the Pocket PC, try going to "start |" Settings | Connections | USB to PC"and unchecking the checkbox"Enable advanced network functionality. "

  HAL

  --

  HAL Hostetler, TCE

  Engineer senior/UPDATED--MS MVP-Print/Imaging - WA7BGX

  www.kvoa.com - KVOA television, Tucson, AZ.

  Live Hot Licks -www.badnewsbluesband.com

• I'm trying to use a printer that connects via USB and he always tells me that it is not a driver?

  Hello

  I'm trying to use a printer that connects via USB and he always tells me that it is not a driver? I don't understand what is happening and I think it's a setting that I have on my computer. Can anyone help? Ive went on the website of the printer to download the driver and the im unable too.

  Hello

  OEM for the printer manufacturer is responsible for the proper functioning of the printer
  and their drivers. Check with the manufacturer of the printer support, their online
  documentation and drivers and ask in their forums.

  Good luck, you need to update or reinstall the latest driver.

  ================================================

  The main issue is probably the drivers, but these can help:

  Add or remove a printer
  http://Windows.Microsoft.com/en-us/Windows-Vista/add-or-remove-a-printer

  Solve printer problems (Vista)
  http://Windows.Microsoft.com/en-us/Windows/printer-problems-in-Windows-help#fix-printer-problems=Windows-Vista&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Solve printer problems (Vista)
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems

  Solve printer problems (Windows 7)
  http://Windows.Microsoft.com/en-us/Windows/printer-problems-in-Windows-help#fix-printer-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Open the printer (Windows 7) Troubleshooter
  http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

  Find the manufacturer's Web site
  http://Windows.Microsoft.com/en-us/Windows-Vista/find-a-printer-manufacturers-website

  Find and install printer drivers in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/find-and-install-printer-drivers

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• HP Officejet Pro 8500 has 910 a, Vista 32-bit, does not connect via the usb port on my PC!

  I used to have it all in one connected to my pc, until I lived some printing problems, so I decided to uninstall it!  When I tried to reinstall, the pc will not connect it.  I tried different ports and have replaced the cable, have also downloaded the latest software and drivers all to nothing does not.  I can connect wireless to my laptop, but unfortunately is not a solution for my office because it is not wireless, so it must be connected via USB.  At my wit's end, please help me!

  Hello

  Can you try to insert a flash drive into one of the USB ports on the printer, to make sure she reads it?

  The printer port may be what gives you the question. In addition, you can try the USB printer connected to another PC?

  Let me know the results.

• Unable to a WiFi but wireless cannot connect via usb

  original title: WiFi wireless connection, but connect via usb
  Hello

  Windows 7 does not respond to a wireless wi - fi connection, but connect via usb

  Hello

  1. What is the brand and model of the computer?

  2. use a USB dongle?

  3. do you get an error message when you try to connect through USB?

  Please provide us with more information to help us more.

  For more information, see this article

  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows 

• Try to synchronize a mobile laptop and it connects via bluetooth, but will not be synchronized

  try to synchronize a mobile laptop and it connects via bluetooth but will not synchronize what I am doing wrong

   
  Moved from feedback
  Original title: device

  "You run a form any of sync on the PC software, usually supplied with the ' phone or available for download on the ' phone manufacturers site.

  As you do not tell us that "phone and helps OS it runs there is little more we can give."

• To connect to the PC - tab 8W - not seen when connected via USB - Help!

  My new 8W tab is not seen by the PC connected via USB. Both are Windows 10. Help!

  Out of curiosity I will pick up an OTG cable and let you know the result!

• drive external hard connected via usb hub powered Time Capsule guard fall...

  Hello.

  Try using a player external 3.5 "connected via USB hub powered to my Time Capsule to serve as a backup Time Machine secondary.

  When I connect the external hard drive, it turns out, and everything seems good (Yes it is correctly formatted). I see the external hard drive in my time machine preferences panel and also the desktop browser window, etc..

  After selecting the drive hard as the second backup TM, I start TM. After a few minutes the backup fruitbodies. Audit of airport utility, the drive no longer appears in the profile of Time Capsule. I can't turn back the drive without unplugging / plugging the USB cord. I went to HD (WD green 4to) and HGST 4to - deleted both.

  What is the speaker (the box is powered)? Can you have a USB hub between the external hard drive and time capsuls? Something else?

  Just seems like something somewhere that expire, causing it to drop the connection...

  Thanks for your useful suggestions to fix this!

  Is your TC the Gen5, model AC?

  I must say that your experience is not uncommon. I tested it myself recently and was disappointed in how the poor reliability has been... Although not as bad as yours... in fact cutting in a few minutes to start a backup is ridiculous.

  What is the speaker (the box is powered)?

  Quality of the envelope varies a lot... What is it??

  If this is the typical brand X... Plug it into your Mac. is it reliable?

  Go to your control panel and dig up the actual USB chip used... I don't know if we can help on type a lot. But it helps us determine the fleas are a problem.

  I found the hard drive in the finder to mount helped... not the sparsebundle that must be mounted by Time Machine... but the disk must be mounted in the finder so that you can copy files back to him.

  I start TM. After a few minutes the backup fruitbodies.

  Check in the finder, it has created the sparsebundle and works.

  Can you have a USB hub between the external hard drive and time capsuls?

  It's our usual recommendation... but he won't always help... especially if the USB hub is another brand X...

  Note that all societies are changing USB tokens at the drop of a hat... some seller of a rival company arrives and offers them 1 c off the coast of 1 million chips it is common to spend even in the middle of a race. Even the tenors have no satisfactory fixed hardware...

  The computer has loads of memory... and may contain drivers for hundreds of different USB tokens... but the TC is a very limited amount of space and with questions if the driver is not fair.

  I started a thread for a database just now... has not progressed much.

  https://discussions.Apple.com/thread/5912861?TSTART=0