bad connection RV042

Similar Questions

• Tecra Z50-A-14 t - bad connection WiFi signal

  In short.

  Absolutely the same problem with my new Tecra.
  Stable connection by cable.

  Bad connection same 3 5 meters from the router. If the distance is longer, or I use the laptop in another room sometimes it s no link at all.
  The card is Intel (R) Dual Band Wireless AC-3160 and that article how I found the link above.

  All electronic in the work of the House with no problem, but this piece of garbage to Wi - Fi only the same has even after 3 visits in the repair shop. And that s for new out of the box laptop.

  I really disappointed me.

  + The message was edited: link has been removed - forum rules +.

  Hmm. have you noticed the same problem of weak signal using the laptop to the power of the battery as well as connected to the adapter?

  My signal low similar knowledge questions may seem due BOF WiFi enabled power saving settings. This setting can be found in the current power plant? Advanced settings

  On the other hand, it might be possible that there is something wrong with the WiFi antenna cable. Maybe it is not properly connected to the mini PCI module

  In the case of changing the settings would not help you and if your already updated the Wlan to the latest version available, I think that the Toshiba certified maintainer should check the antenna.

• bad connect to Sql * more via command and cannot log on to the designer (need for connection string)

  I installed Oracle Developer with success, but having bad connect to Sql more than command line, also unable to connect via the developer tools, I get a TNS: Connect timeout occurred. This happens also for the "Plus" Sql for Windows.

  

  
  

  However, I can connect via the Sql Plus command window when it is executed from "Start-> all programs", but not when I first run the command window:

  

  
  

  I have a good Oracle 11 g install on Windows 7 and a good developer Sql install so I can connect to databases, but something does not work when you try to connect through these tools. Although Sql Plus works when called from 'Start-> all programs'
  

  sqlplus scott/tiger - don't use SQL * Net, you can connect like this even with the listener is stopped.

  Developer SQL can ONLY connect using SQL * Net & can be blocked by the firewall

  to connect using sqlplus & SQL * Net, you need to invoke it as below

  sqlplus scott/tiger@orcl

• INSTEAD, error PLS-00049: bad connection variable

  I try to use a PLACE for me to enter data in a table of bridge. Thanks in advance
  
  I get the following error:
  
  Error on line 4: PLS 00049: bad connection variable ' NEW. MEMBER_ID'
  
  2 INSTEAD OF THE INSERT OR UPDATE OR DELETE
  3 ON VI_Member_Talent_VW making REFERENCE AGAIN AS NINE OLD and OLD
  4. FOR EACH LINE
  5. START TO
  6. IF THE INSERTION
  
  Here is the code:
  
  
  
  CREATE OR REPLACE TRIGGER VI_INSERT_UPDATE_MT
  INSTEAD OF INSERT OR UPDATE OR DELETE
  ON VI_Member_Talent_VW REFERENCING NEW AS NEW as OLD OLD
  FOR EACH LINE
  BEGIN
  IF THE INSERTION
  THEN
  INSERT INTO VI_Member_Talent (Member_ID, Talent_ID) VALUES (: NEW.) Member_ID,: NEW. Talent_ID);
  END IF;
  IF THE UPDATE
  THEN
  UPDATE VI_Member_Talent SET Member_ID =: NEW. Member_ID, Talent_ID =: NEW. Talent_ID
  WHERE ROWID =: OLD.ID;
  END IF;
  IF THE REMOVAL
  THEN
  DELETE FROM VI_Member_Talent WHERE ROWID =: OLD.ID;
  END IF;
  END;
  
  Edited by: user13003575 may 2, 2010 08:53

  user13003575 wrote:
  It's the view

  CREATE OR REPLACE FORCE VIEW  "VI_MEMBER_TALENT_VW" ("ID", "Member_ID", "Talent_ID") AS
  SELECT rowid id, Member_ID, Talent_ID
  FROM VI_Member_Talent
  /
  

  and there is the problem.

  The view was created with quotes around column names, so that they are case-sensitive. You need to either modify your trigger double quote column names, or rebuild the view without the quotes. Personally, I'd go with changing the display.

  John

• Bad connection variable

  Hi friend
  
  I don't want to use a trigger to update a value of varchar2:
  
  create or replace trigger WORK_STITCH_NAME_TRIG
  after insert or update on ASS_WORK_STITCH
  for each line
  declare
  NAME VARCHAR2 (100);
  Start
  If the insertion
  Select ENAME in the NAME of UAMRIS. WORDER where OID =: new. OID;
  Update UAMRIS. WORDER
  Set ENAME =(:new.NAME)
  where OID =: new. OID;
  end if;
  end;
  /
  
  but it gives me error like ': New.Name' variable of bad connection.
  
  Can someone help me with this please!
  
  Thank you
  
  Zitouni

  : OLD /: NEW applies only to the trigger of the columns of the table. Your relaxation is on table WORK_STITCH and the NAME is variable PL/SQL. Simply remove: NEW:

  create or replace trigger WORK_STITCH_NAME_TRIG
  after insert or update on ***_WORK_STITCH
  for each row
  declare
  NAME VARCHAR2(100);
  begin
  if inserting then
  select ENAME into NAME from UAMRIS.WORDER where OID=:new.OID;
  update UAMRIS.WORDER
  set ENAME=NAME
  where OID=:new.OID;
  end if;
  end ;
  /
  

  SY.

• Troubleshoot the bad connection with router (WRT350N) and Point (WAP4400N) wireless access

  Hi all

  I have a problem and will apprecaite all the help I can get. I think I will find an answer here.

  I have a small network, Linksys WRT350N (wireless router) attached to a modem and then connected to a desktop computer and with 3 wireless laptops connected to the router. All 3 are really great to work and access the internet very well.

  Currently, I have the need to expand the network to 3 floors, so I bought 3 Points of access wireless of Linksys (WAP4400N).

  I ran 3 cables CAT5e cable from the router and which ends individually all 3 floors, the top floor is less than the router 40meters. With the cables that came in their boxes, I connected the APs to the router and I have correctly set up the 3 Access Points with them attached to the router, all 3 works perfectly (I can access wireless internet via 3-point). However when I take the points of access to the upper floors and connect cables cat5e APs no longer work but connect after some time with the message "limited connectivity".

  Why can I connect when the APs are connected to the ground floor via a short cable that came in the box and not when it is connected to put cables from the ground floor to the upper floors but rather make the "LIMITED SERVICE" message and cannot connect to the internet.

  Also if I connect the cat5e cables directly to a laptop computer on all the floors, I can connect to the internet (the work of cables fine when connected directly to a laptop computer), but when it is connected to the connection of the APs has failed and I begin to see strange IP addresses from the APs.

  Oh, one more piece of important information: when I connect cables CAT5e cable on all floors direct to a laptop I can connect to the internet (the work of cables very well when it is connected directly to a laptop) but when connected to the failed to connect APs and I begin to see strange IP addresses from the APs.

  HEPL!

  I think I have the forum a status report on my post. As I mentioned in my last post, the problem has been as a result of lower cable at my provider. The network is running smoothly. Has been in place since last week when I replaced the lower quality cat5e cable cat5e cable.

  A Board here please be careful and make sure you complete the cable. A bad end can lead to connection problems I discovered in this case when my team confidence terminated cable incorrectly.

  Network up to & operational: Linksys WRT350N router without wire + 3 Linksys Wireless Access Points WAP4400N + Modem providing access to (1 computer (cable), 6 workstations (wireless), & 5 laptops (wireless).) Network to grow shortly.

  Thanks to everyone who helped make this project a reality.

• Unable connect RV042

  HII,

  I borrowed a rv042 router to a different branch of my office. I couldn't with 192.168.1.1.

  need help

  Good afternoon...

  Go to start-run, type "cmd", and then in the window type ipconfig and lookout for the default gateway.

  Use the defauly gateway to connect.

  Sometimes there could be problems with the browser you are using. Then try to connect from chrome, safari or firefox.

  Thank you

  Marwa

• Bad connection WWAN H5321 GW with TMobile on a carbon X 1

  First off, I installed a version of Windows 7 OEM, then grabbed all updates. I used the Lenovo driver for the card WWAN (downloaded the last one yesterday). I bought a TMobile, installed data SIM card and got a connection I can connect to and get data... for awhile. After about 5 minutes, the connection is very reliable, to the point that I can't get a page of results on Google. Coverage in my area is almost perfect, so TMobile swear that it is the laptop. Seeing that the driver is up to date, I have no other ideas.

  Thanks for sharing.

  Yes, these screenshots saying I'm right - your modem connects to the GPRS/EDGE network and you need to install a tool (for example logins) in order to define the type of network manually. If you decide to do the version after installation of AC, 5.93, as 5.97 is very bad.

  To be more comfortable - ask your operator support team for their 3g network APN. Currently, we see epc.tmobile.com, but some carriers may have different APNs for types of different network and data plans. But the Web says that your APN is correct.

  You can even check is type network T - Mobile 3g in your cocation or not using certain built-in OS commands.

• That means "bad connections" warning to the average of the Mail account setup?

  The Mail account setup dialog box, the works of autodetect IMAP, but after clicking "Done", a warning is displayed (see image), declaring "Thunderbird may allow you to get your mail using the supplied configurations." However, you must contact your administrator or your e-mail provider about these incorrect connections. See the Thunderbird FAQ for more information. ».
  I checked the Thunderbird FAQ (or what is the information that I found) but there is no explanation of this warning.

  On the connection used:

  -C' is a working IMAP with STARTTLS on port 143

  -the server is using a self-signed certificate (not expired), which Thunderbird complains not in the warning

  -with the help of a Setup from another existing SMTP account (no control in the Mail account setup dialog box)

  So I ask myself, what this warning is really all.
  Best regards

  Watch dialog box seems to occur only if:

  • There is an e-mail account, SMTP outgoing self-signed certificate
  • The new e-mail account uses the only existing outgoing SMTP Protocol

  This could be a default in Thunderbird 31.7.0, because there is only one such warning dialog to the configuration of the e-mail account that is used for reporting several different problems. The code (source Thunderbird: mailnews/base/prefs/content/accountcreation/emailWizard.js) power switches of the incoming and outgoing messages, but in this particular case, it seems to turn off all messages - which leaves just the text displayed in the screenshot - compare to https://support.mozilla.org/en-US/kb/server-doesn ' t-use-encryption

  When you use a new profile without all accounts in Thunderbird 31.7.0, new account creation work without such a warning.

• bad connection of the iPhone

  Hey, so I just got a new iPhone off of Ebay and everything was working fine until I decided to use wifi,

  my iPhone cannot connect to the wifi connection when I'm in my room and cannot keep a stable connection in my living room where my router is located in

  So far, IV ' e tried solutions like restart my router, then by restarting the phone etc.

  Other home devices can connect to the internet very well except for my iPhone

  So what is someone having the same problem as me, or at least have a solution to solve this annoying problem?

  I would be very grateful

  Hello, you can try these steps to resolve the problem. If your iPhone, iPad or iPod touch connects to a Wi-Fi - Apple Support Network

• Warning about bad connections contains no option "I understand the risks", I can't move on

  I install Thunderbird on Windows 8.1. I am trying to add 3 accounts. When adding the second account that Thunderbird has warned by transmitting unsecured password. I clicked on "I understand the risks". No problem. When I tried to add my third account, I received the warning again, but this time there was no other choice, "I understand the risks". I can't click on 'Done', if I change the parameter that TB can not find servers. I'm stuck and unable to add my last story.

  I installed on my laptop that runs Windows 7 TB and had no problems. I use the same settings as in my version of TB on my laptop. The version of TB is 24.4 on both machines. Of course, the version of TB was younger, when I installed on the laptop.

  Thank you, in advance, for any advice.

  Bill Halteman

  If I wanted to get the certificate warning when connecting to my email provider's e-mail server, I would like to seriously check the offered certificate. There should be no exceptions to this need in the first place.

  Certificates are there for a purpose, and is not simply to add an exception when it does not work.

• Satellite C660 - two USB Ports without function (bad connection)

  Hello, sorry for the worst English.
  Historically, the touchpad of my Satellite C660-220 used without operation, worked with a mouse of radio. Now, two usb ports can only be used under certain conditions. Can I replace the connections for this part (motherboard / motherboard) for example, a computer used toshiba laptop? Where can I read, one of which models the parts required are the same as well?

  Best regards from the Germany

  Bert

  Hi Bert

  I guess for you that it is quite simple. Problem is that this repair is not supported, and all we can try it on its own, including all the risks of damaging something.
  > Where can I read, one of which models the parts required are the same as well?
  This kind of document is not and if it has information that is not for public use, but for only authorized services.

  Theoretically, you can find the same mainboard with damage CPU or GPU and use parts from there.
  Believe me it is not easy to give you some good advice on this subject.
  Out of curiosity, but you have some experience with these things?

• Bad connection WiFi on my Portege R930-15E

  Hello

  I have a strange problem on my R930 which I tried to solve already for several months, but could not succeed.

  As I recently replaced the WLAN router and the problem remained to the laptop, I know now that it's really the Toshiba which hurts.

  Question: The WiFi is on the 2, 4 GHz WLAN and there are only two local wireless networks here in the neighborhood. The intensity of the signal is supperb (5), but the speed of the network status changes in a few seconds between the 26 and 130 MBit according to the diagnostic tool for Windows 7 (without doing anything with Notepad). I would not care about it if WiFi would work well, but it's not.

  Download videos from YouTube makes sometimes troubled (videos are stuck) but the most important problem is that access to the data to our NAS is really bad.

  I know it can work much, much better that I have also two other laptops that work well, both HP, older than 7 years, shows no such a question, signal WiFi is still at 54Mbps or, on the new, with 150 MB / sec. Other tablets and smartphones also do not have these issues.

  I tried already to have different channels, but does not help. I've updated also the WLAN, the last driver of Toshiba seems to be: Intel Centrino Advanced - N 6235 Version 13.03.2012 15.1.0.21. Is this really the last being?

  In addition, I found around many problems of WiFi in the Toshiba Internet, but so far, none really match my situation.

  But I found that Toshiba seems to have bad WiFi antenna, but I sat just 5 meters from the router, so I don't think that it's a software problem (driver). Operating system is Windows 7 Professional 64 bit.

  Do you have recommendations for me what to do?

  Thank you

  Volker

  Hello
  Indeed, Portege R930-15E was equipped with the Intel Centrino Advanced-N 6235 WLan/BT combo card that supports the 802.11 A/G/N standards.

  The latest driver should be available on the Intel page:
  http://www.Intel.com/p/en_US/support/highlights/wireless/can-6235

  It seems that the latest driver (at that time) was published at 29/12/2014 and its v15.14.0.1 for Windows 8.1
  Anyway, as you can see, this WLan module supports the 802.11A/G/N standards.

  I think you should check in the Device Manager-> properties-> Advanced tab WLan card which WLan standard was chosen. Probably, you could change cela a/g or just N

  Last but not least, I would recommend allows you to check the WLan Card power saving option.
  Option for WLan module energy savings are in the advanced power settings and I recommend you to choose for two profiles (dough/adapter) the performance of the value

• Envy by dint of bad connection Ralink Rt3290 m6

  I hope someone here can help me with a problem I have experienced with my computer. My adapter (ralink rt3290) wireless worked fine out of the box for some time now, but all of a sudden I feel a drop of signal strength on the 2nd level of my house. This has caused drops frequent internet connectivity. I've been browsing google and some of the HP support the forum topics to see if I could give all the answers and tried many solutions with little improvement.

  HP envy m6 - 1184ca

  Model no. C2L94UA

  Wireless LAN adapter model: rt3290, last Ralink driver installed 5.025

  Updated BIOS updated to F.32

  Operating system: Windows 8

  -Another active wifi devices work fine on the 2nd floor. I don't think it has to do with the router. I will restart it after that I have post this thread.

  -J' fiddled with several revisions of driver without end I had similar problems with a card atheros on a Toshiba laptop that has been repaired with a 3rd driver. Currently, I'm on the latest driver 5.025 and fiddled with the settings of wireless network without success. I'll try to run a windows update to see if that fixes the problem.

  -J' opened compartments accessible user on the bottom of my computer (and nothing else) and made sure the antennas are well seated in the card, no luck. Fortunately, I did affect all the components in the process

  -I did not fell, spilled something or manhandled this laptop since I bought it.

  Everybody don't think that the network card is defective, at this point? I sure hope not, but I'm starting to get suspicious: [if I can fix it at home somehow I would prefer that.] I understand that the card itself is not the 'higher end '; I got what I paid for. I have a repair pending for a defective LCD for this specific model, so I would also like to know if I can ask HP to replace the network adapter as well before I send, with the hope that it improves the issue? The laptop is fairly new and I'm still covered by the limited warranty. Otherwise, I would like to know what would be the other alternative and more stable network adapters is compatible with my motherboard, OS and wlan slot (I'm not too familiar with computer hardware) because the issue is now beyond my knowledge! Any help would be greatly appreciated :)

  OK, I was using the default windows driver and while my connection is always to 2 bars, my connection has been constant and school drop-outs were not held. So far, it has been difficult to my problem as the ralink drivers seem to cause more problems than they fix. If my connection is still not great... it's there, and so far it works great. I'll check with this topic to see if I put a permanent end to my problem...

• Bad connection to laptops only

  I have a Nighthawk AC1900 router a few months back. Everything has worked great so far. Laptops in the House have lost connection with it. We came back for a short period while after I turned off the router and then restarted, but it loses then in a few minutes. IPad and mobile are connected as usual without problem.

  Is this a known problem with a known solution? Any help is appreciated.

  Thanks for your reply. In fact, it is now ok. I have reset the router which was then also updated and implemented again that fixed the problem with one of the laptops. The other laptop was fixed by quenching with its network setting after resetting the router.

  Now, I just hope that this weird problem does not return. : )