Bad display of the printer

Similar Questions

• "Printer properties cannot be displayed. The print spooler service is not running. "(even when it works)

  When I click with the right button on a particular printer and try to view the properties of it, I get the following message:

  Printer properties cannot be displayed.  The print spooler service is not running

  It is, it is run as go to-> Services administrative tools in the Control Panel checks.

  One of the 'printers', I installed is "send to OneNote 2007".  I can click right on this very well - just not this another printer. I'd be able to do if the print spooler is not running?

  Indeed, if I turn off the print spooler, * all * printer in "Printers and faxes" disappear.  So the fact that I'm still see them first place suggests to me that the printer spooler is running.

  I posted this on Microsoft.public.windowsxp.general a while ago and someone suggested that I visit this site .  Problem is C:\WINDOWS\system32\spool\PRINTERS is empty.  It is empty when the print spooler is running and it is empty when it is not.

  Also, I was unable to install KB896423 since I am running SP3.  Try to install he did the following:

  Setup has detected that the version of Service Pack for this system is newer than the update you are applying.

  There is no need to install this update.

  The printer is a "local printer attached to this computer" connected via a "Standard TCP/IP Port".  Personally, I think such a printer should be called "a network printer or a printer attached to another computer", but that is the terminology used by the "Add Printer Wizard".

  Hello terrafrost,.

  Thank you for visiting the Microsoft answers community.

  What is the model number of the printer that you are using?

  Printing a "Standard TCP/IP Port, is used for a printer that is directly connected to a network, not on your local system.

  I would try to uninstall your printer and reinstall your printer.

  Hope this helps Chris.H
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Computer not found displayed on the printer control panel. ?

  Computer not found displayed on the printer control panel. It analyzes not but prints ok. Running the utility HP scanner Diagnostic 4.2 says service Windows Imaging does not. If you ignore this message says the Twain service does not work because it is used by another service?

  Problem solved. I managed to get Windows Imaging served running afetr a lot of the research and this scanner enabled to work. Thanks, but does not need your help after all!

• Check if the page is displayed in the printer friendly mode

  I have a page with a button that loads the page even, but in fun mode of the printer. However, I have a button I want to be displayed if the page is in friendly print mode (a button to launch the print dialog box) however I want not displayed in normal mode.
  
  Y at - it a variable session or another way to determine if a page is displayed in the printer friendly mode?

  Hello

  Change your button and go to the Conditions section. There, you will have 2 options that will solve your problem:

  "Current page is printer friendly Mode"

  and

  "Current page is NOT in Mode friendly printer.

  --
  Paulo Vale
  http://Apex-notes.blogspot.com

• Printer properties cannot be displayed. The print spooler is not running.

  I followed the MS KB "file sharing and printers with different versions of Windows" for instructions on connecting my new Win 7 PC to several domestic XP PC in my network. However, once that I had on the right by clicking on the printer for XP to share, popup message "printer properties cannot be displayed. The coil of the printer does not work. This has happened even when clicking on the properties of the printer. I'm stuck now and need guidance on what to do. Thank you!

  Here are the steps of general network troubleshooting. Just cannot apply to your situation, so just take the bits that are. It may seem daunting, but if you follow the steps in the links and suggestions below calmly and consistently, you will have no difficulty to implement your sharing.

  Problems sharing files between computers on a network are usually caused by 1) a misconfigured firewall or a firewall neglected (including a dynamic firewall in a virtual private network); or (2) inadvertently run two firewalls such as the firewall of Windows and a third-party firewall. and/or (3) do not have accounts to the same users and passwords on all computers in the workgroup. (4) tries to create actions where the operating system does not.

  In Windows 7, go to control panel > everything in Control Panel > network and sharing Center. Click on "change the advanced sharing settings. You don't want to use the residential group unless you have all Windows 7 machines. If you do and you want to use the homegroup, see Windows 7 Help & Support. Otherwise, in sharing advanced:

  Discovery of plug in the network
  Open the files and printers sharing
  Turn on the sharing section Public folder sharing
  Plug the password protected sharing

  A. configure the firewall on all machines to allow traffic to local area network (LAN) as being approved. With the Windows Firewall, turning on window file sharing and printer as the above will take care of that for you. If you are not running a third-party firewall or you have an antivirus/security with its own firewall component program, then you're fine.  With a third-party firewall, I usually set up the allocation of LAN with an IP address range. E.g. would be 192.168.1.0 - 192.168.1.254. Obviously you would substitute your correct subnet. Refer to the safety of any third party program or the user forums for how to correctly configure its firewall. Do not run more than one firewall. DON'T STOP FIREWALLS; CONFIGURE THEM CORRECTLY.

  (B) to facilitate the Organization, put all computers in the same workgroup. This is done from the System applet in Control Panel, the computer name tab.

  C. create the counterpart of the user accounts and passwords on all machines. You do not need to be logged into the same account on all machines and assigned to each user account passwords can be different; accounts/passwords just need to exist and to match on all machines. DO NOT NEGLECT TO CREATE PASSWORDS, EVEN IF ONLY OF SIMPLE. If you want a machine to boot directly to the desktop (a particular user account) for convenience, you can do this:

  Start > Search box > type: netplwiz [Enter]
  Click continue (or provide an administrator password) when you are prompted by UAC

  Uncheck "users must enter a user name and password to use this computer". Select a user account to connect automatically by clicking on the account you want to highlight and press OK. Enter the password for this user account (when it exists) when you are prompted. Leave blank if there is no password (null).

  XP - set up Windows to automatically connect (MVP Ramesh) - http://windowsxp.mvps.org/Autologon.htm

  D. Si one or more of the computers on your network are XP Pro or Media Center, turn off Simple file sharing (Folder Options > view tab).

  E. create share as you wish. In Windows 7 I usually share the Desktop of the user and the Public directory.

  F. you have the job of file sharing (and tested by exchanging a file between machines), if you want to share a printer connected locally to one of your computers, share of this machine. Then go to the printer mftr Web site. and download the latest drivers for the correct system. Install them on the target machines. The printer must be collected during the installation procedure. If this isn't the case, install the drivers and then use the Add Printer Wizard. In some cases, printers must be installed as local printers, but it is outside this response. MS - MVP - Elephant Boy computers - don't panic!

• Solution no display of the print options Center

  I have a photosmart C309a and if she was well for several years. Recently, I've lost the solution Center printing options on my main pc (it's just to show the scan options).

  I can print programs or emails using the menu program or the Explorer using the right menu of the mouse, but do not have the options in the center of the solution. I had been using a wireless network for my PC in a network, but because I couldn't solve printing problems I uninstalled and installed the latest version of the software and am now using a USB to my main PC - network computers use the printer on my main PC rather than directly in network. This has not solved the problem.

  I tried to run Hp print & scan doctor and utility Diagnostic equipment, who say that the software and drivers are all to date and working correctly.

  I don't know if the fact that the print options do not appear in the Solution Center is a problem or just a function of recent software, although I have these options on a PC in network. Comments or help appreciated.

  Hi alad26,

  I understand that you have updated the Solution Center is not all the features he had done previously for your Photosmart C309A printer. I will do my best to shed some light on that for you.

  With updates of our printing software that these options have been deleted because none of the printers HP product have the same characteristics as your Photosmart done, such as printing on CD. So there is nothing wrong with the Solution Center, these functions have just been deleted.

  If you are wanting to the solution center with your options of origin, that can be done. You must have your original software CD because it would have the old version of the HP Solution Center on it that has the features that you are now missing.

  Hope this helps, have a nice day!

• Is this a bad display or the inverter? Or could it be something else?

  Pavilion dv4-1225dx Entertainment Notebook PC

  It is a LED display? State record: 14,1 "Diagonal WXGA high-definition HP BrightView Widescreen Display (1280 x 800)

   

  Original forum post with the video of the screen of the problem:

  http://h30434.www3.HP.com/T5/notebook-display-and-video/flickering-display-at-startup-but-stops-jump...

  15 f009wm 8.1 WIN 64 bit
  Office Jet 2540
  P2-1113w WIN 7 64 bit
  G71-340US WIN 7 64 bit
  dv4-1225dx VIsta 64-bit
  zd7000 WIN XP Pro
  xv886 Millennium WIN / WIN XP Pro
  HP deskjet 6980xi
  HP pavilion xt236 / ze4200 WIN XP Media Edition

  SOLVED

  First tried the best route, new inverter $4.89, but the problem persisted.

  Replace the LCD ($65,75) and the problem is solved.

• Bad display of the description of the object

  Hi all

  I have page responsibility Iprocurement page name and path is:

  / Oracle/Apps/ICX/por/reqmgmt/WebUI/ReqDetailsPG

  
  

  This is the request page and it contains two-piece 1 is part of the history of requisition and part 2 detail belongs to...

  
  

  In the detail part there is a table that contains the number of columns as line, description, by necessity, delevery - to and so on.

  In my case this special request to have 5 folders... In the detail table, that means show 5 lines, 5 description and so forth...

  
  

  
  

  My problem is with the Description column of the table in this detail

  This page after "ReqDetailsVO" and ItemDescription is the value of the attribute of this description column...

  "ReqDetailsCO" is this page CO...

  
  

  Now the question is when I click on copy on the shopping cart button, it goes to another page... / Oracle/Apps/FND/Framework/WebUI/OADialogPage

  This OADialodPage contains 3 buttons Cancle, add to cart and wagon again... In fact, it's a warning page

  
  

  When I click on new button basket, then it goes to the shopping cart page... This page contains a table that contains items in the shop...

  table contains columns like line, the item description, special info, unit and so on...

  Here she also have a record 5, but in the description of the article show other values... his watch is not the same value or description as my previous on the previous page ReqDetailsPG
  

  shows item description...

  
  

  This page shopping cart shoppingcartpg/oracle/apps/icx/por/req/webui/ShoppingCartPG the page number and the access path.

  Co: ShoppingCartCO

  VO:PoRequisitionLinesVO and view attribute: ItemDescription

  
  

  Now how to display the same description of the object on the page of ShoppingCartPG ?

  Can I track the CO extension method or what? and how?

  
  

  
  

  Thank you...
  

  
  

  
  

  Hi Sandeep... Actually I changed method to solve it... requirement is the same but the method has been changed...

  I close this and I raise thread for new requirement...

  Thanks for your help...

• ERROR MESSAGE HP6700 - PROBLEM WITH THE PRINTER OR INK SYSTEM CONTACT HP

  I JUST BOUGHT A HP OFFICEJET 6700 (LESS THAN 1 WEEK), THE PROBLEM OF PRINTER OR INK SYSTEM MESSAGE, TURN PRINTER OFF THEN WE IF THE PROBLEM CONTINUES CONTACT HP. IS DISPLAYED ON THE PRINTER SCREEN. I DID EVERYTHING SUGGESTED, AND MORE MORE, BUT THIS CUSTOM MESSAGE CLEARLY.  ALL DIAGNOSES OF THE PRINTER THE PRINTER IS FINE.  THE OPERATING SYSTEM IS WINDOWS 7.

  Mahamoud,
  Your article made a walkthrough basic troubleshooting, ending with the question if the print head is repairable. Because it is not on the 6700, the article isn't really the problem.
  
  Here is the solution I found to this problem:
  I discovered that eliminating all ink cartridges allows the printer at startup (although there is a message saying the missing print cartridges).
  Putting the cartridges in a binary regression revealed that the ink has been bad. (In my case, I only got the message of failure/printer ink when the yellow cartridge was in the printer).
  Replacement of the restored cartridge the printer functionality.
  That's the good news.
  Now the bad news: for HP.
  The generic error message indicates a failure with the printer or the ink system. No differentiation. With the electronics in the cartridges (that the client pays a high price for), looks that HP could not understand how to indicate a cartridge problem. This error message is not only unnecessary, but misleading. The printer indicates only a power reset and then contact HP. There is no indication that he might be a cartridge problem, not to mention what cartridge has failed. By the way, my customer encountered this problem when you replace the color cartridges. The cartridge failed was a new replacement.
  All of the web enabled features, fax, scanning features, print included with this printer are not very useful if the user can't get the dang thing to print.
  Another problem with this printer, is that, even when you only print in b & W, the printer uses little color (ostensibly make Blacks more "BOLD"). Then, finally, a color cartridge will go low or empty, even if only B & W printing. And guess what, you can't continue to print n & B if one of the color cartridges are out of ink. Thus, HP... How is this useful printer in an office environment, where most print tends to be B & W?

  (I would add; the solution in the message of failure/printer ink cartridge cannot fix your problem if, in fact, there are a few default printer. But if the problem is in the ink system, then the troubleshooting cartridge can help you).
  I have posted similar comments on Amazon, for this printer, in the subject line: shame on you, HP.

• How stop "low on ink to the printer" error message on ipad

  HP Officejet 5470 continues to send a low on ink error message to my IPad. I don't know my printer settings to disable these messagets, help!

  You won't find any printer or the printer settings. AirPrint is a diffuse wifi printing system, so that these messages are actually sent by your printer and simply displayed on your iPad.  Stop messages, to bad draw on the printer itself.  If it is low on ink, then replace cartridges.  If this is not the case, check the printer manual or online support on erasing the incorrect error messages or status.

• How to cancel the print job with HP8610 Control Panel

  Is it possible to cancel a job using the control panel of the HP8610 instead of using the Task Manager?

  @LucyRicky,

  If a print job is in progress, you should see an option 'Cancel' on the display on the printer. Press Cancel to stop the print job.

  I hope that helps!

• How can I remove the documents from the print queue?

  I can't get my printer to print as says the error message "cannot print due to a bad configuration of the printer".  I updated the drivers and reset the default printer...

  Once I opened the box of the print queue and tried to cancel all documents.  They would not go far!  Help, please.

  Hello

  This should help:

  View, pause, or cancel printing
  http://Windows.Microsoft.com/en-us/Windows7/view-pause-or-cancel-printing

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• HP Office Jet Pro 8600 help how do I enlarge the print on an original when it is in copy mode?

  I find it on my help screen how do I enlarge the print on a copy of an original document that I want to copy. I have Windows 7 on my computer and printer is HP Office Jet Pro 8600 wireless. I have a printer HP (3 in 1 officejet) before and it was much more user friendly. Is to use the online mode?

  Here is a link to the user manual. To get the possibility to enlarge the copies, press this option on the display of the printer, then tap SETTINGS and then select resize, use the right arrow key to scroll through the sizing options on the printer. Changing the settings of copy is covered on page 59 and 60 in the manual. I hope this helps.

• get error ul 101-8200 cannot uninstall the printer

  This message keeps coming up so I can't uninstall the printer software

  Hello

  ·         What is the brand and model of the printer?

  Method 1:

  Follow these steps and check if that helps

  (a) click on your "Start menu", then "settings", then "printers and faxes" menu. This will show all of the printers and faxes currently associated with your computer.

  (b) if it is currently associated with your computer, delete the printer from your computer. Right-click on the printer icon and select 'delete '. Confirm the deletion by selecting "Yes" in the pop-up window.

  (c) access the "Server Properties" menu in the menu drop down "File" at the top of the window. Select the 'Drivers' tab at the top of the window. This will display all the printer drivers installed on your computer.

  (d) highlight the printer driver that you want to delete by clicking on it once. Click on the button "Delete" under the list of drivers. Click 'Yes' in the context menu to remove the driver. Repeat this step to remove drivers that are additional, if necessary.

  Method 2:

  To resolve this error, upgrade your printer software to the latest version.

  How to download and install the latest printer driver from your printer manufacturer's Web site

  http://support.Microsoft.com/kb/2677141/en-us

  Method 3:

  If you have the latest version of the software and the error persists, this could be due to malicious software on the computer. Run an anti-malware program to identify and remove malicious software.

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

• HP Officejet Pro 6830: Get the printer and the message "the printer into an error state" will not be printed

  Just received this printer refurbished HP 2 weeks ago to replace the one who had a problem with printhead.  Printing worked initially, but now I get the message "the printer into an error state" when I try to print.  The screen at the front of the printer automatically turns off as well, as he is extinguished.

  Hi @M45,

  Thank you for joining the Forums of HP Support!

  I see that you are unable to print because the printer is in an error state. I will definitely do my best to help you and don't forget to come back to this thread and mark "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I would like to do a hard reset to see if that will solve the problem.

  1. Let the printer and disconnect the printer cable and the wall socket for 60 seconds.
  2. Reconnect the power cable to the output of the printer and the wall, and not a surge protector. This ensures that the printer is full on and can help this situation.
  3. Make sure that the printer is connected directly to a wall outlet (do not use a bar or a surge protector).

  If there's an error message displayed in the menu on the front panel, before the display of the printer turns off?

  Please download and run the print and Scan of the doctor, it will be probably diagnose and fix the problem you are experiencing.

  • What were the results when you ran the printing and scanning doctor (she print or scan, error messages)?
  • Click here to update the firmware of the printer with a USB connection.

  If you have completed all the above steps and your product still has a problem, service the product.

  Check the warranty status: http://h20564.www2.hp.com/hpsc/wc/public/home
  Cost of repair out-of-warranty printers may apply.
  What you can do, is to use the following link to create yourself a file number, then call and it can help to expedite the appeal process:
  Step 1. Open the link: http://support.hp.com/us-en/contact-hp
  Step 2. Enter the product number or select Auto detection
  Step 3. Scroll up to "still need help? Fill out the form to select your contact options.
  Step 4. Scroll down and click on options contact HP - click Get phone number
  File number and phone number are displayed.

  I hope this helps. Please respond if you have any questions. I wish you a nice day!