Battery switch

Similar Questions

• Error message, unbalanced power supplies, battery switch, cisco 3750 x

  Hello

  A new Member switch has been added. There seems to be a power supply problem as alerted in the newspapers of the switch, as shown.

  Journal:

  % PLATFORM_STACKPOWER-4-UNBALANCED_PS: electric battery switch 3A unbalanced power supplies

  When I watched this show, research has pointed out this bug; CSCtg20513. The bug suggested orders, below;

  You can enable or disable ports (stop/no closed) battery on the unit which incorrectly reports this error.
  config t
  battery-switch
  Standalone
  no autonomous

  However, these commands have been ineffective.

  See the Version

  Version 12.2 (55) SE3,.

  Any other suggestions to help, is very much appreciated!

  Thank you

  JoBee

  That fix is an earlier version, SE2, SE3 is not down like 1 of the service version that is why he can not work

  12.2 (55) SE3 is almost to the State deferred as well as I would upgrade to a more recent image which now has 4 years of

  Have you tried to manually reposition the power stacks

• Satellite A200 - loses the battery, switch off the power

  I have a relatively old Satellite A200, yet almost all inside is new except the battery. The battery has a very short life, but that's because its old. Recently the computer started to suddenly lose the battery, so the charge light stays on, the battery light turns off and the battery icon said "plugged in, not charging." However, the computer still work on battery power. If I see it at the time, then by removing and replacing the charger repeatedly, I can start it load again, but if I am not it switches off without warning. Since the battery life is now less than a minute which often.

  I don't think that the problem is with the charger because it always shows the charger is plugged in, and when the computer is off the battery light is always on when it is plugged. I had a problem with the power connector, but if the motherboard was recently replaced so I don't think that's it either.

  If someone could help it would save me a lot of frustration, thank you.

  Hello

  At first, I must say that you should not be frustrated. Problems with consumer products are normal, and each of us has problems with laptops, televisions or other electronic product.

  Let's see what you can do about it.
  Your description is OK, but what I want to know is follow:
  When you remove the battery can work on your laptop with no problems (start work, cut)?

  I also think that the battery is too old and I presume it's troublemaker in the history. It is not easy to explain what behavior flashing if you have a defective hardware or old coin inside.

  Maybe, you need to buy the replacement of the battery and check the features for laptop and the battery, just to see if everything will be OK again. If you will be faced with the same problem again then we can discuss what may be the problem.
  In my opinion only a reason for this could be electronic power supply.

  What do you think?

• Alpha 12 battery switch

  Since i ' v decides to keep what I was looking for programs to stop or remove that increases the battery life.  41/2 hours is quite ridiculous.  No matter what success there in the extension of the battery?

  I have an alpha 12 switch. I need a powerbank for her. I saw your energizer powerbank. Can you give me more information on this subject. Where I can buy it?

• should I battery switches

  Hello

  I was wondering if dell considers it more practical stacking iscsi switches (e.g. 6224) or to keep separate them with aggregated uplinks.

  Dear,.

  Huw

  Stacking is better than the chutes.  Less general, more low-latency, higher throughput.

  Also make sure you have the latest firmware for the 6224.  If using frames, place the iSCSI in their own VIRTUAL local area network ports.  (Ports of server and EQL table).   Value size MTU 9216.

• Switch 10 battery health

  I got a Switch 10 for about three months now, and it dawned on me that I don't give much thought to the maintenance of the battery. I use mostly my switch for reading, browsing the Web and a few games that does not require much memory or horesepower. Some days, I drain the battery down to AB. 10%, but other days I plug in the charger when it is only 80% or more.

  So what is the best strategy to maintain the battery switch 10 for the long term?

  TIA

  The user guide has information on the functioning of the battery and how to optimize your battery life. I included a link to this guide below. See the battery section in the user guide.

  http://global-download.Acer.com/GDFiles/document/user%20Manual/user%20Manual_Acer_1.0_A_A.zip?acerid...

• HP pavilion dm4: removing the battery / output switch problem

  MY hp dm4 Clubhouse has a switch relese battery does not move and so I can't remove the battery.

  What can I do to take out the battery?

  I was able to remove my battery, even if the trigger will not move

  I have read the documents under the next heading

  "Laptop battery seems to be stuck.

  He pointed out that my problem was very common

  BATTERY REMOVAL PROCEDURE

  As suggested-

  I inserted a piece of thin stiff plastic

  (for example on the size of a credit card but a little thinner)

  in the crack between the battery and the output switch

  I pushed the upper part of the plastic down

  and then I pushed up in the direction of the battery

  up until the crack of batttery widened to the point where I could use

  my nails in the battery of crack to pull the battery.

  I don't have to much force to make

  The angled battery to easily

  BATTERY INSERTION PROCEDURE

  As suggested-

  To avoid the problem of gel battery switch

  Move the latch of the battery in the middle of its sliding range

  When reinserting the battery first tilting the battery

  so that the side of the battery to the side of the computer case

  is first inserted into the battery compartment

  Then push down the other side of the battery in its compartment

  in the end, release the battery button while he spingngs to its normal resting position.

  I hope that this explanation is useful

• 1xPS4000 and 1xPS6000 switch between 2 x 6224 battery plugged wth LAG to be able to do a fw update

  Hello

  I'm about to failover of iSCSI traffic connecting 6 Esx 4.0 host and 1xPS4000 and 1xPS6000.

  My problem is that the version of Esx do not allow me to change the connection timeout iSCSI from 5 seconds to 60 dry such as recommended in the EQL docs. If it would work it would not be a problem to make a switch of the controller, but with this problem I'm unsure if I'll lose iSCSI - connections causing some or all of the vm:s to go down when the passive controller became active in the stack of the 'new '.

  I tried to do a "manual failover' taking a cable both of the active controller and its connection to the new"stack", but this was done on 1xPS6100 and 1xPS4100 who have not havie any connection iSCSI in their regard.

  My question is if it is an appropriate option, even when the iSCSI connections are on members or are there better options?

  We greatly appreciate your advice

  Cree

  Hello, are you talking about the upgrade of the firmware of the switch or the EQL firmware?  I assume that the switch.

  If you have two LAG'd batteries with connections between them, and then restart each battery switch should cause no problems.

  You can move a cable at a time.  Put an end to all connections on this link and the iSCSI initiator to reconnect.  Make sure this link is always accessible.  That is, if you move a port of the Bay, ping the IP address of the port of connections to the server on both switches.  You want to make sure that the links between switches working properly.

• IPhone 5 sec stops randomly after a battery replacement

  Hello!

  My battery of my iphone started to disappear after 1.5 years and I decided that it needed a new spare battery and maybe he could fix it. So I bought one and the tools and made myself, I changed the battery and the phone worked. Now the problem, first, the battery is still hurt like the old, it drains toward the low real fast, and on the other hand, the most annoying problem ever. My iphone just randomly turns off completely without any warning or error, it's just black. Sometimes like all the days of 15 times. I use, put it in my pocket, pick up after like 5 minutes and its judgment. Sometimes even when I use it, it just goes off like that. Its so annoying!

  10 minutes earlier before, I was in bed and listen to music using my iphone, it's just off. I can not even use my phone to alarm more because he died during the night.

  Can I do to solve this problem? Help, please

  (I tried factory reset the phone did not work)

  Hello Ogen98,

  You probably expect this response, so don't let it get to you.  It is ok.   It is certain that it's your own battery switch that is behind your problem of 99%.   I suggest you enter your phone into an Apple store, but I'm afraid that they will not touch it after a third of repair.   Of course, we can't imagine what you did and you wouldn't get much help here because most people have no idea of the innards of a phone.

  I think you have to bite the bullet and replace it.   You need reliability.

• My 157 A60 loses power and cheated on battery

  A few weeks ago my power adapter A60 stopped working so I replaced it with a universal adapter. I checked if it was compatible with Toshiba laptops and plugged.

  When I use my dvd player, or burn videos to dvd the power of the adapter to the battery switches and I only have a battery installed in my laptop. It's weird because as soon as I remove the disc it switches back on current alternative.

  I'm assuming that the AC adapter is defective somehow because I never had this problem with the original Liteon power supply that came with the laptop.

  Does anyone have any ideas or ways to cure the problem? I'm fairly certain that the adapter is defective and cut the power off when the drive is in use, but it's a strange thing happens.

  Just to add - if your laptop goes off (as mine did!) blow through the grill and fan and remove dust. A straw is usually the case. It is solved the problem of disabling for me.

  Hello

  I suspect that your 'universal' adapter is not able to provide enough current when your laptop is important on this issue, for example when you use your optical drive. It is likely that your adapter has an overload protection system that cuts the power when a too heavy load is placed on it.

  Kind regards

• Add new N3048 to current stack of switch

  Hello

  I have a new N3048 switch to add to our current stack of 2 N3048 to provide more capacity. Before lighting for the first time, that I would like to know if I need to run through the initial configuration or can I just connect the new battery switch and power, it will then get the config of the switch?

  The firmware must also update on the battery, can I do this first or when all 3 switches are in the stack?

  Thank you very much.

  Since the existing battery and the new, we can have different firmware revisions, generally the best route is updating the firmware on the existing stack, and then on the new switch to add before attaching it to the battery. You should not need to do any initial configuration before attaching. As always recommended is to use a ring topology when stacking to avoid "split brain" IP address and duplicate problems are common with chain failures.

  B

• Configuration of the L3 Switch to send the traffic to Palo Alto

  

  Please forgive my ignorance when it comes to Palo Alto. This is the first time that I do business with them. We need to ensure one VLAN located behind the Palo Alto. I am including a diagram to show a simulation of what we seek to do. We have by default VLAN1 which is our default data VLAN. We have 19 VLAN is VLAN we want it secure. The VLAN1 SVI IP is 10.1.1.1 and VLAN19 SVI IP is 10.1.2.1. On the Palo Alto, we have an IP interface was like 10.1.1.2 for default data VLAN and 10.1.2.2 for the VLAN secure. There are also a pair of HA with IPS 10.1.1.3 and 10.1.2.3 respectively. We have EIGRP that announces the network default VLAN1. Here's what we want to do. Anything from the 10.1.1.x network, go to the 10.1.2.x network, must pass through the Palo Alto. Whatever either from the 10.1.2.x network, must go through the Palo Alto as well. Nothing to any other network 10.1.1.x, takes the route by default (and), and anything from 10.1.2.x to anything else on 10.1.2.x should stay local to the LAN (not pass through Palo Alto. Need just for the MAC address arp). My question is, how do I tell my L3 switch to send all traffic created in the 10.1.2.x, through the Palestinian Authority? I can't do an IP route because from the local network VIRTUAL lives on these L3 switches and is a directly connected route. Really, I can't do the ACB on the switch, because that is really meant to routers. I can put a long match, for everything on the 10.1.2.x network (i.e. the route ip 10.1.2.7 255.255.255.255 10.1.1.2), but for some reason when do whatsoever of 10.1.2.x another thing goes on 10.1.2.x through the palo alto so. Anyone have any suggestions on what would be the best practice, from a network perspective, on how to do this? Thanks for any help!

  Looks like you want all traffic to and from the secure virtual local network to pass through the firewall of your description?

  I'm not familiar with Palo Alto firewall is so I don't know how they work in HA, IE. with other devices do you want to simply talk to a VIP which is responsible for two firewalls?

  In your example the two firewalls have an IP address per vlan, but always just use you one IP addresses for the end-end connectivity. I'll assume that you do, you may need to change, but when I say that I mean the one that reminds you of the devices for routing etc..

  So for all the traffic to and from the network 10.1.2.0/24 to go through the firewall, you must-

  (1) remove the battery switch the IVR for vlan 19. You need the firewall to be routing vlan not secure the 3750 s. You leave vlan 19 in the database for vlan.

  (2) point them vlan 19 customers as default gateway

  (3) addition of a route on the stack of 3750 for the network 10.1.2.0/24-

  IP route 10.1.2.0 255.255.255.0

  (4) if the 10.1.2.0/24 network needs to talk to other that 10.1.1.0/24 remote subnets, then for each of these networks the firewall should be a route. The syntax will not be IOS, but this should give you an idea-

  IP 10.1.1.1 road

  etc... for each remote network

  That means foregoing is all the traffic going and coming from 10.1.2.x customers to other subnets must go through the firewall. The customer traffic in the vlan secured to other clients in the vlan safe doesn't have to go the firewalls.

  Jon

• Ring operating in half of the battery

  Hello world

  I have 2 battery switches

  HS switch stack-ring speed

  Stack Ring speed: 16G
  Configuration of the stack ring: half
  The ring protocol stack: StackWise

  HS switch stack-ring activity

  SW frames sent to (approximate) ring of the battery
  ------------------------------------------------
  1 16864205185
  2 3894031560

  Total frames sent to the ring of the battery: 20758236745

  They have only cable single battery connected right now.

  Need to confirm if there is any advantage in speed if I connect another cable battery also. ?

  It will increase the performance of switch?

  Thank you

  MAhesh

  Disclaimer

  The author of this announcement offers the information in this publication without compensation and with the understanding of the reader that there is no implicit or explicit adequacy or adaptation to any purpose.  Information provided is for information purposes only and should not be interpreted as making the professional advice of any kind. Use information from this announcement is only at risk of the reader.

  RESPONSIBILITY

  Any author will be responsible for any damage that it (including, without limitation, damages for loss of use, data or profits) arising out of the use or inability to use the information in the view even if author has been advised of the possibility of such damages.

  Poster

  In theory, yes connect the other battery cable provides superior performance, as you will have two stack active links between your two units.

• Electric battery query 3750 / 3850

  Hi all

  I'm putting together some 3850 different batteries. Exceeded a bit about installation, as well as the priorities of the POE / PowerStacks etc.

  I then decided to take a look at one of our production (5 x 3750 X) batteries, we have in place that has been a part 3 earlier. I see the following. Can you think of a reason why it's set up like (2 separate power batteries) this or they forget turn on the power in aid of the

  battery-switch x x port turn on some of the power ports? I can't think of any other reason, it's like this.

  SH battery-power supply Details
  Power battery battery battery Total Rsvd Alloc unused Num Num
  The Mode name topology Pwr (W) (W) Pwr Pwr (W) (W) Pwr SW PS
  --------------------  ------  -------  ------  ------  ------  ------  ---  ---
  Ring PowerStack-5 SP - 2480 1000 796 684 4 5 PS
  PowerStack-4 SP - PS 1430 520 332 578 1 2 Stndaln

  Name of battery power: Powerstack-5
  Stacking mode: power-sharing
  Battery topology: Ring
  Switch 1:
  Power budget: 190
  Allocated power: 190
  Low-value priority port: 21
  The priority value high port: 12
  Change the priority value: 3
  1 table of port: Shut
  2 port State: connected
  Neighbor on port 1: 0000.0000.0000
  Neighbor on port 2: 3 switch - b0fa.ebad.dc00

  Switch 3:
  Power budget: 190
  Allocated power: 190
  Low-value priority port: 22
  The priority value high port: 13
  Change the priority value: 4
  Port 1 status: connected
  2 port State: connected
  Neighbor on port 1: switch 1 - b0fa.eb7c.c780
  Neighbor on port 2: 5 switch - b0fa.eb7c.c280

  Switch 5:
  Power budget: 190
  Allocated power: 190
  Low port priority value: 20
  The priority value high port: 11
  Change the priority value: 2
  Port 1 status: connected
  2 port State: connected
  Neighbor on port 1: switch 2 - 0006.f6bb.e380
  Neighbor on port 2: 3 switch - b0fa.ebad.dc00

  Switch 2:
  Power budget: 910
  Power allocated: 226
  Low port priority value: 19
  The priority value high port: 10
  Change the priority value: 1
  Port 1 status: connected
  2 port State: not connected
  Neighbor on port 1: 5 Switch - b0fa.eb7c.c280
  Neighbor on port 2: 0000.0000.0000

  Name of battery power: Powerstack-4
  Stacking mode: power-sharing
  Topology of the battery: autonomous
  Switch 4:
  Power budget: 910
  Allocated power: 332
  Low-value priority port: 22
  The priority value high port: 13
  Change the priority value: 4
  1 table of port: Shut
  2 port State: not connected
  Neighbor on port 1: 0000.0000.0000
  Neighbor on port 2: 0000.0000.0000

  Thank you

  Disclaimer

  The author of this announcement offers the information in this publication without compensation and with the understanding of the reader that there is no implicit or explicit adequacy or adaptation to any purpose. Information provided is for information purposes only and should not be interpreted as making the professional advice of any kind. Use information from this announcement is only at risk of the reader.

  RESPONSIBILITY

  Any author will be responsible for any damage that it (including, without limitation, damages for loss of use, data or profits) arising out of the use or inability to use the information in the view even if author has been advised of the possibility of such damages.

  Poster

  3750-X batteries, using cable between switches of members, are limited to four units.  What is this battery?

• Why isn't the Thinkpad X100e no battery, HDD, wifi, power light?

  Can anyone help?

  Hello

  My ThinkPad X100e (Type 3508-CTO) has the following three indicators:

  1. Power - solid Green around power button when the system is running
  2. Sleep - solid Green if standby (standby), flashes when entering or coming out of sleep
  3. Battery - switch between solids,-flashing slow and fast-flashing Green and solid, flashing slow and fast-flashing orange according to the load

  The other lights are probably not present because of the space, power and cost reasons, but access to Microsoft Windows 7 and Lenovo connections indicate the status of the connection Wireless on the screen and you can use a program like HddLed indicator, DriveGLEAM or DKHardDrive-light to see the situation of activity for the hard drive. on the screen.

  Kind regards

  Aryeh Goretsky