BB 10 next Jam?

Similar Questions

• HP LaserJet 1022: Reset fails to kill orange light after the paper jam. I try next?

  I followed the instructions to reset this (quite old) printer after he picked up several sheets at once and it reported a paper jam. He was not in fact any paper left inside, but I gave it a clean anyway.  By pressing the two buttons for reset, I get three lights in unison, but when I release, it goes back to flashing orange and still think there is a jam. Never had a problem persisting like this before. A packed his little brain?

  JDH49,

  If you've been through the steps listed above the printer risk requires troubleshooting. You can reach the support - to the 800-474-6836. If you do not live in the United States / Canada region please click the link below to get help from your region number. http://www.hp.com/cgi-bin/hpsupport/index.pl - for the maintenance options.

  Good luck!

• OfficeJet Pro 6230: Officejet Pro 6230 continous (not of paper) paper jam error

  As soon as the printer powers on it the ink carrier Wizz backward real quick (as he struggles to move) and then gives me a paper jam error (the resume light flashes and error appears on my screen). He did the same thing when I try to print anything (including the status report page).

  When I up the access panel upward (power on), the carrier of ink isn't even move to ink cartridges which can be changed. I try to move with force, but it does not move (if I use more strength, somethings will break). Ink is a bit new, so I don't know it still has ink in there.

  The steps I've tried:

  plugged the power supply into the wall outlet

  roller cleaning

  THERE IS NO PAPER or PAPER PIECES BETWEEN ROLLERS (I checked like 20 times)

  reset the printer

  There is a large black gear coupled to a white average speed on the left side near the bottom of the printer. I manually drove the speed by pressing (rotation) of North (or forward or to the rear of the printer) for a few seconds and once I did that. the ink carrier was able to move as it's supposed to, and I could see the ink. but once the power is back on, the carrier of ink was in the locked position and fights again and gives me the paper jam error.

  I don't have really any troubleshooting documents on the CV online on how to fix a jammed media of ink and clearing paper jams, so I'm out of options.

  It is plugged into USB

  The main problem is the paper jam error.

  I don't know if the stuck carrier of ink is the cause.

  Hi @Comp-Tech.

  Thank you for joining the HP Forums!

  I noticed your post that your printer HP Officejet pro 6230 receives a constant paper jam error. I'm happy to help you!

  Since you did all the steps already to troubleshooting in this guide, A 'transport Jam' Error Messageand this guide, "Problem of tray or paper jam" Error Message appears, as well as the reset of the printer. The next step is to fix the printer / or replaced.

  Please Contact HP phone support for assistance. (After you fill out the information, you will receive a phone number.) If you do not live in the United States / Canada region, please click the link below to get help from your region number. Language-country selector.

  If you are unable to reach a resolution, please click on accept solution. If you appreciate my help, please click on the thumbs up icon. The two icons are below this post.

  Best regards!

• OfficeJet 6600: Paper jam resulted in ink system failure

  Paper jam resulted in the failure of the inkjet system. Error 0 x 61000016 is reported.

  I tried troubleshooting basic procedures, but the track of the cartridge seems to be poorly aligned, that is, when I opened the door, only the black cartridge is available. This is definitely not normal.

  The above error messages persist after stopping and restarting. Replace cartridges results in the same error.

  The jam massive caused many, many problems. I had to fish out bits and bits of paper of all nooks and crannies.

  Too boot, when it was all cleared up I had to cold start the printer, remove and reinstall all the cartridges (because the printer is no longer recognized an any of them) and go through a three step routine cleaning print head.

  Very messy.

  But the good news is that everything is all right work

  My next gripe is about the ongong with cartridges properly filled with Staples, Costco, and al that so-called re - define the chip in the cartridges.

  That never works.

  The result is that the printer does not recognize an original HP cartridge when it is filled again and then starts the everlong question when a cartridge is empty actually.

  Of course, I know when a cartridge is empty, it weighs about 19 grams.

  But we should not do that math.

  I understand that HP would love everyone to buy their cartridges, but they cost way too new.

  Seems average spririted. I could be wrong, but we are all in this together.

  The ink is ink. I think HP should be a little more forgiving for us "little guys" who need to pinch pennies.

  Just saying '

  Rainman

  P.S.: And Yes, I agree the continuous message on 'counterfeit cartridges' when I plug a Costco filled HP cartridge. They are not counterfeit, they are actual filled HP cartridges of actual real RGB ink! And, of course, I accept the responsibility addressed by the messages of ad nauseam when I insert these original re-filled HP cartridges. They seem to work well. Perhaps there could be a happy medium where HP could give a little and the moniter ink levels. Of course, I can continue to weigh the cartridges when the print head cleaning routine fails to get good results. But again, HP should be a little more friendly and less motivated in this respect of profit.

  But having said that, the disorder shoot works great, and I appreciate it!

• Photosmart HP 6520 series: paper paper jam?

  I got the series HP Photosmart 6520 for Christmas.  While I'm still not sure how to get my Macbook pro to recognize it... my daughter was able to use it with an application on his phone.  We test printed a few things and it works beautifully.  So the next time he said a paper jam.  We removed the paper does nto seem to be stuck.  Always says paper jam.  Don't know how to fix a paper jam, when there is no paper in it.  Can someone please advise?

  Hi Aziz,.

  I'm sorry that you are having a problem with your Photosmart 6520 new.  Please see this document for assistance.

  Sometimes there is no jammed paper and the printer just needs to be reset.  Other times it IS paper stuck somewhere that is not visible.  The document that I joined you through all these instances and should get you operational return!

  I hope this helps!

• HP officejet 8500: jam on fax error message

  My printer gives me a paper jam error message everytime I try to fax on the set of the car. But he fine Fax out of the glass. Also, it prints multiple copies of auto tray.   Amy ssuggestions before buying a new machine.  It is 5 years old.

  Hi @Horseshoer,

  Welcome to the Forums of HP Support!

  I see that you are not able to communicate by fax using the ADF on your HP Officejet 8500 printer. I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I understand that you are able to fax using the scanner, which is nice to hear. I also see that you mentioned that you are able to copy of the set 'auto '. Are you referring to the ADF (automatic document feeder) or the feeder?

  If you are able to copy multiple pages using the ADF, fax should also work. The printer may have a little problem, that can solve a reset.

  I would like to do a hard reset to see if that will solve the problem.
  Let the printer and disconnect the printer cable and the wall socket for 60 seconds.
  Reconnect the power cable to the output of the printer and the wall, and not a surge protector.
  This ensures that the printer is full on and can help this situation.

  • Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector) This ensures that the printer is full on and can help this situation.

  If you have a computer that is running Windows 7 or an earlier version, I would update to the firmware of the printer. Clickherefor the download page.

  If you are unable to update the firmware of the printer, I suggest to try partial reset or Semi - full Reset. I can send you this information in a private message. In the forum next to your handle name simply click on the envelope to see.

  Please reply to this message with the result of your troubleshooting. I can't wait to hear strings attached good luck!

• HP psc 2210: clear jam on my hp psc 2210 all-in-one printer

  The lights on my printer and the message says: "open the door.  "Clear carriage jam, and then press ENTER.  I do not see a "jam", opened the door and press enter several times.  I still can not reset unplugged machine from one day to the next.

  I think the cartridges are "stuck" on the side of the machine and they are unable to drag in the middle.  Can someone tell me how to fix this jam?

  Would be very grateful for the help!

  Renee'

  Hi @sreneecesand welcome to the Forums of HP!

  I see that you are having problems with jam.  I would like to help!

  I recommend starting by remove (if possible) ink cartridges and perform a power reset the printer.  Unplug the power cord from the printer and the power outlet, then wait 60 seconds. After 60 seconds, plug back in the printer. Make sure that you connect the printer directly to a wall outlet. Make sure to bypass any surge protector or power bar.
  
  I would also say to following the steps outlined in this document:

  A display of the Error Message of "open door, clear transport jam, and then press enter" for HP PSC 2170 2100 and 2210 all-in-One Series Printer "

  Good luck and please let me know the results of your troubleshooting operations. Thanks for posting on the HP Forums!

• transport paper jam in the printer

  How can I pay for carriage jam in my HP printer {removed privacy} 6310xi. I triied every step of troubleshooting according to the tune

  There is a document with steps to help solve a problem of paper jam carriage in a 6310xi. The document can be accessed here.

  If the steps in the document does not erase the question, the next step will be to replace the printer as a hardware problem has developed. I hope this helps.

• Printer stopped working after I removed a paper jam - Deskjet 6988

  I removed a paper jam today, according to the instructions. But since I did it, it will not be printed. The power light is, as if it's OK, but he absolutely refuses to print.

  My printer is a HP Deskjet 6988 and I am on Windows 7, 64 bit.

  Whenever I try to print, the print queue displays the print job for about a second, then he faints. I try to print again, it disappears. Then, if I do it a third time, it appears in the list and stays there, but the printer does nothing.

  After two minutes the queue no longer mentions it as the "impression". Instead, it says, "error printing". I try to delete the print job, but it just sits there, saying "error printing". It will not erase. The only way to remove it is by the printer stop or restart the computer.

  If I try to print after that stuff all over again.

  I tried closing the printer and reboot, restart the computer, power cycling (stopping the printer, unplug the cables, waiting..., plug again and restart).  I ran the Diagnostic Utility and it tells me that it works very well - well, very good for a very large paperweight.  I used troubleshooting via the Control Panel, and he said: "a print job in the print queue prevents other printing of print." But as I have already said, delete the print job does not solve the problem.  I am stuck in a loop of the removal of print jobs and nothing works.

  Help, please!

  Hey Tigger,

  It may have been stuck in the diagnostic mode - not able to move forward or backward for a time very long.

  Next time, if this never happens again, you can try a Reset of the printer:

  Here are two types of reset the base printer:

  (1) if there is a keyboard, turn it off, then on and press on # and 6 (press and hold while turning on the printer).

  (2) without a keyboard?  So unplug that LEAVE unplugged for 30 seconds to a minute.  Reconnect it.  (Be careful with this one - will not shock).

  It can become a little more complicated than that, but a basic reset sometimes "will have the printer attention" if it's just "spinning" and nothing else will not physically.

  I'm glad it works again.

  Maybe printers receive loners.   The smile.

• HP PSC 1410: Nonexistent jam

  My printer has taken several pages using both and they stuck at half way through.  I released these carefully and open at the front and the back of the printer to make sure that no paper was blocked. All the lights on the printer are green so printer looks good to go.

  I watched the video to help to ensure that I did as stated and held the 2 keys on the printer to print a test page.  The test page printed without problems.  However when I then tried to print a word document that I had created it would not print, always advised paper jam.  Print pages of test OK but no document.  Strange ideas?

  I agree that it looks like a glitch in communication between the printer and the computer. I suggest to use the following steps to remove the printer from the device and printers and the driver from the properties of the server.

  1. in the folder "devices and printers".

  2. choose "print server properties.

  • Win XP - with no printer selected, click 'File' then 'server properties '.
  • Windows Vista - with no printer selected, press 'Alt' and then click 'file' then 'server properties '.
  • Windows 7/8 and 8.1 - Select any printer in the "Devices and printers" folder and click on "Print server properties" above.

  3. click on the "Drivers" tab at the top of the window "properties of the print server.

  4. choose the printer that you want to uninstall, and then click 'remove '.

  5. choose "Remove driver only.

  6. the next screen will give a warning, letting you know that the removal of the driver package will remove it from the system. Click 'Yes' to say are you sure you want to do.

  If documents are stuck in the spooler to print, you see an error, cancel all documents waiting in the print queue or try restart the spooler to print, and then try to delete the driver from 'Print server properties' again. If she will not always remove the sachet, restart the computer and the printer should correct this error "in use" and allow the driver to be removed.

   

  • If him you continue to get an "in use" message followed the steps in the document here. The specified printer driver is currently in use

  Once the driver is then deleted, open start > all programs > HP folder > folder printer > HP Setup and software (or the icon of the printer).

  The installation screen and the software opens and you can click on connect a new printer.

  

  Thanks, I look forward to hear back from you again.

• OfficeJet 6700 gear grinding noise and paper jam

  When turned on, our 6700 OfficeJet 6 - months, goes through the boot process, makes a gear grinding noise and finally stops with an error message of paper jam.  I went through all the steps to remove a paper jam (there was no paper to clear) except the cleaning rollers.  It of as if the gear in the duplex unit is not quite the tail with his partner in the printer, but not sure.  I checked to make sure that the rollers turn freeling.  The duplexer gear is a little tight, but it does not move.  Any ideas?

  It seems that this printer has developed an internal problem.  From the sounds of it, the issue is the release mechanism for the transport of the print head.

  There is a document to help out the noisy operation found printer here.  This can have a few extra steps for troubleshooting paper jam you have already done.

  I would also try re-allocation of places the duplexer if she appears out of alignment.  However, if the problem persists, then it will be a hardware problem that the next step is replacement of the product.

  If you are still in warranty, HP can replace the printer without cost to you. I'll link the information to get in touch with them below. The link takes you to a form to fill out. Once you fill it and she is treated, it will give you the printers warranty information, a file number and the phone number to call.

  Technical Support case HP formula call: https://h10025.www1.hp.com/ewfrf/wc/phoneInput?cc=us&dlc=en&lc=en&product=5061082

• LaserJet 1300 paper jam

  LaserJet 3100 C3946A USBF021323 Mfg October 13, 1999

  Use of the history/primary

  A fed not location of several page for years. Only OK food for my purposes. Is not used for fax or printing from the computer. Use main scan and copy.

  Malfunction

  To replace the empty toner cartridge. First scan and copy effort leads to a paper jam in the copy with part of page rest phase in the feeder (don't remember if used not simple or multi bin for food). Page fired back with normal resistance (no tear or missing corners). First 1/3 of page was released folded in the second 1/3. Toner deposited as expected the first 1/3 and 1 inch in 1/3 second. Toner condition dry dust, unheated. Deposited toner clear and distinct than original scan. Next effort of scanning and copying. Sheet inserted in the tray sheet to the statement "Bin is empty please add paper." This resulted in "printer paper Jam check paper" Path message when paper is inserted. Can't see any piece of paper inside. Restart by pressing the "Stop/Clear".  Also turned off by unplugging the power cord for several minutes reconnect. 'Jam' same message when paper is inserted. Reinserted previous (almost empty) cartridge with results of same message "insert a paper and jam." Also tried the two reboot methods thanks to this previous cartridge.

  I would appreciate any advice that may fix this problem.

  Larry Strayhorn

  lstrayho@email. UNC.edu

  Thank you for your help.

  I guess I have nothing to lose by using the maintenance manual for the test of unity of fusion/heater.

  Larry

• you plan repair xp Pro-fichier asms download of service pack 2 reinstallation disk computer jams _

  Repair Windows xp

  Hello

  ·        What is the exact error you receive and message in what phase?

  ·        What do you mean by computer jams?

  ·        You are able to start to start on the desktop?

  It could be that the files that are present in the disk are damaged. I suggest using another drive and check if you are able to repair. You can use your product key even if you use another disc.

  If you are able to boot to the desktop then, I suggest you follow the steps mentioned below.

   

  Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following link.

  http://support.Microsoft.com/kb/322756

   

  Step 1: Open command prompt, and then type regedit into the registry editor. Go to HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318} and see if there are keys Upperfilters or LowerFilters. If they do, save the key and delete upper and lower filters components.

  Step 2: Close the registry editor and open Device Manager by typing devmgmt.msc. The CD ROM drive will always have an exclamation point. Right click on the drive (one by one if necessary) and go to delete. Right-click on the name of the computer at the top and go to "Scan for hardware changes". This should list the disks again. You should now be able to see the installation.

  Step 3: Type notepad on the command prompt and press to enter. This will bring up a Notepad window.

  When Notepad opens, click on file and go to open. The open dialog box is displayed. Switch the selection of the type of file to all files. Go to the CD ROM drive through the icon my computer on the left side of the dialog box. When you get the content of the CD-ROM drive, you will find the i386 folder.

  Step 4: Right-click on the folder and go to "copy". Go to the root of drive C by using the icon workstation. Right-click in the window of C and go paste. This should start the copy of the files from the CD ROM drive on drive C.

  Step 5: Wait for the files to be copied. When it is finished, close the dialog box, close Notepad and the command prompt. When the next mistake of copy of file occurs, you can navigate to the i386 on the C drive folder. You will have to do with each copy of file error that occurs.

  This obviously won't work if the disc is damaged. If the client gets errors in copy of file during this process as well, consider that the CD may be damaged in some way.

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit ourMicrosoft answers feedback Forum and let us know what you think.

• HP all-in-one C310 with a message "clear jam of transport."

  I have a C310 with a message "clear jam of transport."  I followed all the instructions on the website of HP, but get the same message.  The transport is really moving, so I don't understand why I get this message and how to fix!

  Did you check with a flashlight inside the printer if ensure there is no small paper completely left or all the way inside the printer?  The transport may be able to move, but if she can't move along the transport route, then it will produce a carriage jam error.

  There is also a document with the steps to resolve this error, but I see that you say you've done most of them, which can be found here.

  If you perform all of the troubleshooting steps, and the error will not disappear, then the next step will be the replacement of the product.  If you are still in warranty, HP can replace the printer without cost to you. I'll link the information to get in touch with them below. The link takes you to a form to fill out. Once you fill it and she is treated, it will give you the printers warranty information, a file number and the phone number to call.

  Technical Support case HP formula call: https://h10025.www1.hp.com/ewfrf/wc/phoneInput?cc=us&dlc=en&lc=en&product=5061082

• HP photosmart c4280 issue transport jam

  Tried the hard reset as suggested, still getting the same message. "Jam, jam clear transport transport. Press OK. Any suggestions? Like new, used one summer in my truck. Cheaper to buy a new one and it crash?

  There are a few things I would do in this case.  I remove all paper from the paper tray and make sure that it is no that whatever it is taken in the rollers that would block the way of transport.  Also, look inside the printer on the right side of the cart and make sure there is nothing blocking the movement of the cart here.

  Have you tried to raise transportation and trying to move gently by hand?  Can it go all the way to the left and all the way into the printer?

  There is also a document with more troubleshooting for a jam carriage found here.

  If all the troubleshooting steps are carried out and the error continues to be present on the screen of the printer, then the next step will be the replacement of the product.  If you are still in warranty, HP can replace the printer without cost to you. I'll link the information to get in touch with them below. The link takes you to a form to fill out. Once you fill it and she is treated, it will give you the printers warranty information, a file number and the phone number to call.

  Technical Support case HP formula call: https://h10025.www1.hp.com/ewfrf/wc/phoneInput?cc=us&dlc=en&lc=en&product=5061082