Behavior of the ASA

Similar Questions

• Go back to the previous behavior in the address bar

  Just upgraded to Firefox 31.2 and I find that the new behavior of the address bar is in conflict with how I work. I often copy / paste URL, I type directly into the address bar, I use a current to go to about.config tab and none of these work. I found a reference to the evolution of the gfx.xrender.enabled false, but this did not help. Clues on how to revert to the old behavior?

  It's about: config with a colon...

• Behavior of the filter action "stop filter execution.

  What is the intended behavior of the filter action "stop filter execution"? I can't find any recent documentation on this issue. When part of the filters manually execution, "Stop filter execution" is intended to stop all other filters for all messages if the filter that contains both matches? This seems to be the behavior for me. When included in the first several filters filter, only the first filter matches and the log only shows instances of correspondence of the first filter, although several other subsequent filters must correspond to several messages that don't match not the first filter.

  I appreciate the functionality of Thunderbird filters, but I try to find a solution to implement more complex logical Boolean to move messages from my Inbox with the help of manually run filters. I have several filters put in place to classify the messages, but I want to implement filters such that they are not applied to tracked messages. Currently I have the logic in most filters do not match a favorite message using the option 'Match all the following', however this prevents the use of the logic of the GOLD in the filter and led to an increase in the number of filters. I want to set up the filters as a first filter messages from games played and prevents other filters running only for messages that match the filter first.

  Maybe the behavior I see is a bug specific to my system, but I would like to get a confirmation on the expected behavior and see if others have encountered this problem. I work under the assumption that the behavior of "Stop filter execution" must stop subsequent treatment only for messages on which a filter containing is as indicated in the old post to https://groups.google.com/forum/#! topic/mozilla.feedback.thunderbird.prerelease/rUXaQ0NdZvM, but this assumption may be wrong.

  Any help or suggestions are appreciated.

  OK, it seems that this is a bug documented, for example to https://bugzilla.mozilla.org/show_bug.cgi?id=552936. I should have searched for bug reports before posting here. I follow things with bug reports. Thank you.

• I get a strange behavior of the bar tabs and the address bar in Firefox 29,0 for Mac.

  I just installed Firefox 29,0 for Mac.
  I have a strange behavior of the bar tabs and the address bar with this new version.
  Instead of the address bar, I get two rows of symbols. And it is impossible to write anything in the address bar.
  (I add a screenshot, but I can't find a way to do it).

  Firefox has an RSS icon in the palette of the toolbar that you can drag a toolbar (but not on the location bar container).

  • Firefox menu button > Options/Preferences > toolbars
  • View > toolbars > customize

• FF13 different behavior on the two machines home page

  FF gives different results than "Home Page" on both machines.

  On the desktop, I get my set (the former google/firefox one) homepage.

  On laptop, I have two tabs, the first of about: at home, the second is my fixed home page (the same old google/firefox one).

  On the desktop when I press home, page becomes whole-home page.

  On laptop when I press home, new tab is launched to give me my whole-home page.

  The behavior on the desktop is what I expect and what I want. Which continues with Notepad and how do I do the same thing as the Office?

  Check your settings on the laptop home page, you have inadvertently defined two pages as your home page...

  See - How to set the home page

• change in behavior of the button home and end

  Hello
  I have a problem with the behavior of the home, end, PG. PREC, PG. next and arrow keys. After that I have upgraded to version 6, they do not work as expected.
  I disabled each extension and the behavior is always the same...

  They work as intended in IE8.

  I hope someone has a solution.

  Make sure that NUMLOCK is not engaged, as the keys Home, End, PgUp and PgDn are often superimposed on the numeric keypad. There should be fire of keyboard for Numlock.

  Press F7 to activate the navigation with the keyboard on or off, you want it out. Test after changing.

  To reduce the problems of caret navigation, see

  http://dmcritchie.MVPs.org/Firefox/Firefox-problems.htm#caret

• Behavior of the modified mice

  I have an Ideapad Y560 with a mouse Bluetooth Lenovo A - 300 M. Normally, when I click on a folder, the folder opens. When I place my cursor in Google, I am allowed to write. I can browse using my mouse.

  But today, everything 'glue' to my cursor.

  When I click on a folder, the folder stick (as I am dragging the file) to my cursor.

  If you go to Google and put my cursor in the search box, the url of the Web site 'glue' to my cursor and 'glue' in the search box.

  If I click on a white spot on my screen, the cursor created a blue indicated selection box that changes size when I move my cursor.

  I press 'ESC' to take off everything that is glued to my cursor. I have to click several times to close a window or make a selection on a Web page. For the most part, I can't use my mouse because it does not work properly.

  I have updated flash and run windows update. I restarted. I put new batteries in my mouse. I ran a virus check. I downloaded the latest driver of Lenovo mouse (from 2010!), but I get a message that my current driver is more current than to Lenovo. I deleted my mouse device and reinstalled. I changed browsers. I'm out of ideas.

  Help?

  It seems that your mouse broke down. Recently, I threw on a mouse who showed similar behavior. The problem is that the switch within the mouse gets stuck.

• Unexpected behavior with the Option "record in the result.

  Hello

  I have unexpected behavior with the Option "record in the result.

  I have a few steps in the subsequence 'X', this subsequence passes a Boolean parameter. According to the value of the parameter I change the "Recorgind results" Option to report it or not. The thing is that if 'result Recorgind' set at race time I modofy by changing the value of Step.ResultRecordingOption to "Enable" and "Disable", the step is not reported until the same sous-suite 'X' is called for the second time (without changing the parameter passed).

  For example: (Preconditon: result Recorgind Option of all value sous-suite x are defined as Disable)

  1 CallSubsequenceX(Parameter: Enable)

  2 CallSubsequenceX(Parameter: Enable)

  3 CallSubsequenceX(Parameter: Disable)

  4 CallSubsequenceX(Parameter: Disable)

  Expected result:

  1. measures have been reported.

  2. measures have been reported.

  3. measures have not been reported.

  4. measures have not been reported.

  Result:

  1. measures would not same value Step.ResultRecordingOption has been changed to 'enable '. (Not Ok)

  2. measures have been reported. (Ok)

  3. measures reported same value Step.ResultRecordingOption has been changed to 'disable '. (Not Ok)

  4. measures have not been reported. (Ok)

  I use TestStand 2013 (5.1.0.226)

  Thanks in advance.

  -Josymar.

  Hi josymar_guzman,

  I just review the sequence and indeed we´re experience unexpected behavior with the Step.ResultRecordingOption callback. By a reason when you run the callback in the expression before each step section, the statement runs only until the next sequence is called, which is not what we want.

  To avoid this, you can place a statement before each step of the sequence, so you can change the State of the Option "record result" for the sequence running (and it is only the following). You can try something like this

  

  where the expression of the statement will be the recall "RunState.NextStep.ResultRecordingOption is YourCondition". With this, we guarantee that the results of the next step will be saved or not. I also remove the expression in the expression prior to each step section, because the condition is now on the statement before each step.

  I tried and it works fine. I´ll set the sequence that you share with me, with the changes. I hope this will help you and solve your problem.

• Strange behavior of the WHILE loop

  Dear experts LabVIEW

  I would ask you to give me an explanation of the behavior of the very simple VI as an attachment. This VI contains a WHILE loop with three parameters, input and STEP. The table of RESULTS shows the calculated values. Considering the input parameters OF = 0 TO = 1 LEVEL = 0.1, then the RESULTS table contains the values 0, 0.1, 0.2,..., 0.9, 1. Considering the input settings ON = 1, TO = 2, STEP = 0.1, then RESULT table contains values 1, 1.1, 1.2,..., 1.8, 1.9. The question is, why the number 2 is missing?  (I also tried to use different types of data, but without success). Thanks for your thoughts.

  Juraj

  Because you compare floating point numbers.

  For example, 0.1 cannot be represented in exactly in binary, cela repetitive additions probably will not end in an exact integer later.

  Since the three entries, you can calculate the number of values exactly and use a loop FOR. Do not use the convoluted code...

  Why not just use ramp model?

• PCI-6221 behavior off the power

  Hello

  A card PCI-6221, tension of the PC is out of snap-ins:

  When I inject a voltage (5V) input ana on the map, this tension is copied on the other analogue channels.

  Room I turn on the PC, and 6s after, injected tension is more copied on the other tracks of ana.

  What is the normal behavior of the map?

  Thank you pour your answers

  Hello Cedric,

  The behavior of the card when it is turned off is not defined. What is it you have a problem in your application?

  When you area PC, this one seems to provide power to the bus PCI 6 seconds after it starts, which explains why the map then adopts its operation.

  The best advice I can give you is to respect the configuration/connection of analog input (manual page 58 Chapter 4-14 M-series cards). About the card, if it works properly when the PC is turned on, and that the connection am well the guide, there is every reason to be reassured.

  I wish you a good day,

  Marc-Junior

• How to open the port 161 on the ASA and Cisco switches for monitoring of BB

  Dear all,

  I want to install BB to monitor snmptraps suffering of failure.

  The newspaper shows BB cannot connect to all ports of the switch 161, and I even can't telnet to 161 XXX_17f for example.

  My switches are Cisco C3550, C2950, etc. of the ASA.

  Mon 7 Nov 15:43:03 2011 bbnet cannot connect to the server XXX_17f on port 161

  Mon 7 Nov 15:43:03 2011 bbnet cannot connect to the server XXX_9f on port 161

  Mon 7 Nov 15:43:03 2011 bbnet can't connect to XXX server on port 161

  Thank you

  Anson

  no need to adjust anything in bb-hosts. If you have added setings in bb-hosts, delete them. Also remove associated in bbvar/logs log files. (otherwise, you'll have purple when you delete the SNMP, trap tags bb-hosts)

  A column of trap will be that no show until the device sends a trap to BB.

• No access to the interface of the ASA by behind the other is

  Hello

  I am faced with the issue of not being able to access the interface of "dmz" behind the interface 'internet '.

  Here is a brief description of the topology:

  

  List entry on the internet access "," allows for 1xx.xxx.172.1 traffic.

  No nat is configured between these interfaces.

  The routing is OK because hosts on the DMZ network are accessible from the Internet.

  The software version is 9.1 (3).

  Security level of the interfaces is the same.

  Security-same interface inter traffic is allowed.

  Here's what packet trace says:

  tracer # package - entry internet udp 7x.xxx.224.140 30467 1xx.xxx.172.1 det 500

  Phase: 1
  Type:-ROUTE SEARCH
  Subtype: entry
  Result: ALLOW
  Config:
  Additional information:
  identity of the 255.255.255.255 1xx.xxx.172.1

  Phase: 2
  Type:-ROUTE SEARCH
  Subtype: entry
  Result: ALLOW
  Config:
  Additional information:
  identity of the 255.255.255.255 1xx.xxx.172.1

  Result:
  input interface: internet
  entry status: to the top
  entry-line-status: to the top
  the output interface: NP identity Ifc
  the status of the output: to the top
  output-line-status: to the top
  Action: drop
  Drop-reason: (headwall) No. road to host

  Please help me find the cause why asa is unable to find the path to its own interface.

  Thank you in advance.

  Hello

  You will not be able to connect to an IP address of an interface ASA behind another ASA interface. It is a limit that has been there for Cisco firewalls as long as I can remember.

  The only exception is when you have a VPN connection that is connected to an ASA interface, then you can connect through this VPN connection to another interface of the ASA. In this case the ASA will also require that you have the following command

  access to the administration

  Where is the name of the interface to which you are connected.

  -Jouni

• Strange behavior of NAT ASA 5505

  Hello

  We have an ASA 5505 version 9.1 (5) and we need to open port TCP 55055 firewall that redirect to TCP port 80 on ip QNAP Viostor 192.168.11.254

  I added a network object in this way:

  The Viostor object network

  Home 192.168.11.54

  Description QNAP_Viostor

  NAT rule:

  NAT (inside, outside) interface static service tcp 80 55055

  Firewall rule:

  access-list outside_access_in line 8 Note Viostor

  allowed to Access-list outside_access_in line 9 extended tcp any Viostor eq 55055 object

  When I try to connect with the application Android Vmobile I see that notify the journal of the ASA:

  Request TCP and eliminated from MY_EXTERNAL_IP to outside:X.Y:Z.W/55055

  The ASA has no server UDP which serves the UDP request

  I don't understand why UDP instead of TCP.

  Please help me!

  Thank you

  Ahmed, thanks for your replies... However're missing you something important (sw ASA version). Tracer package shows THAT NAT is not affected; and on this sw version ACL does not use external_IP or mapped IP, but the real_IP instead.

  s.be00001, follow these steps:

  object service 55055 service tcp source eq 55055object service www service tcp source www!nat (inside,outside) 1 source static Viostor interface service www 55055!access-list outside_access_in line 9 extended permit tcp any object Viostor eq www

  Run the packet - trace and send us the results:

  packet-tracer input outside tcp 8.8.8.8 1025 [outside interface IP] 55055 detailed

• How to block ping the ASA 5506 outside interface?

  I configured a Cisco ASA VPN configuration and Setup. Everything works fine. The SAA outside interface is to pings (on the internet) which is a threat to security. How to only block ping to the external interface without interrupting the functions of the ASA. I tried what follows, but does not seem to work.

  outside the IP = 169.215.243.X

  ASA 2.0000 Version 2

  Access list BLOCK_PING refuse icmp any host 169.251.243.X echo-reply

  Access-group BLOCK_PING in interface outside

  You have set up the ACL is only for traffic that gets sent through the ASA, ASA traffic is controlled in different ways. For ICMP, you can refuse the rattling of the SAA and that allows all other ICMP with the following configuration:

  icmp deny any echo outsideicmp permit any outside

  It is also possible to ban all ICMP:

  icmp deny any outside

  The 'truth' is probably somewhere between these two options. It's your choice.

• Licenses of the ASA, a license or two for a failover pair

  I had two units ASA firewall configured as a failover pair.  Now I need increases the SSL VPN license, do I need a licence for the ASA pair or two licenses, one for each unit.  Can use a key of activation on both units?

  One thing I know for sure, put the key on the Active unit, cannot synchronize the license to the standby unit.

  Thank you very much in advance.

  It depends on the version. The ASA 8.3 and later versions, you can share a single license through an HA pair.