Black screen after turning on computer for Vista...

Similar Questions

• Black screen after leaving the computer idle for some time.

  Original title: Black screen

  Laptop screen starts to turn black every few seconds so I don't use it to take a short break.  The only way to get back the screen is to move a finger on the mouse pad, otherwise, it is just black.  The only way to stop what is happening is to switch off the laptop, wait a few moments and then turn on laptop.  But if I take another short break, this cycle repeats.  Any ideas please.

  Hello

  To provide the proper resolution, I would need more information on your side.

  (1) did you last changes made on the computer prior to this problem?
  (2) did you put the screensaver in a vacuum?
  (3) do you have any particular power on your computer(sleep/hibernate) model?
  This problem can occur if the screen saver is put under vacuum.
   
   

  I suggest you to set the screen saver because none and check if it helps. To configure the screensaver to zero, follow the steps described in the article.

  Change your screen saver
  http://Windows.Microsoft.com/en-us/Windows7/change-screen-saver

  Hope this information helps. Answer the post with an up-to-date issue report to help you further.

• iPad black screen after turning on the voiceover

  I turned voiceover on and then when I locked my ipad. I tried pressing the locking button and button "home" together and that has not fixed my problems, the apple logo appears when booting up, then briefly the lock screen. Any ideas as to what I should try?

  A black screen with Voice over on East to reduce the screen. Triple, tap the screen with three fingers to remove the screen.

  Or

  Siri say politely, 'Vouceover Turn off.'

• Black screen after BIOS windows computer acer laptop 10

  Hello

  While I was watching a movie, when I watched, my webcam from nothing.

  I watched the movie again. then a box of AVG showed, I didn't know what he was saying.

  then my screen went black, I put my laptop, I did it again. the screen acrer showed, after that, there was a screen with this:

  _

  logo: _ flickered, I can go in F2 and F12 only nothing more.

  Now, my laptop makes weird beep is HEARD after 5 seconds

  Please help me!

  error?

  Uh, it says this:

  Cannot transfer recorded messages to the event log with status 50

• Get an error message when turning on the computer, then just get a black screen after the message saying cannont find script file c:/windows/run.vbs

  Original title: windows does not

  I have windows 7 and get an error message when turning on the computer, then just get a black screen after the message say cannont find script file c:/windows/run.vbs

  What can I do?

  Enter your bios usually with keys F2 or delete to the first powered

  Use default Optimize can be the F5 key and save and exit,

  Insert your installation disc or flash media and press F8 or F12 to boot on it

  Then use the recovery tools to run the Startup Repair tool.

  http://Windows.Microsoft.com/en-us/Windows/Startup-Repair-FAQ#1TC=Windows-7

• At the end of the factory restore, but black screen after "Windows has set up the computer.

  The model in question is VC863AA #UUW

  I want to get back the computer to the factory condition, so I rebooted and you press F11. Everything went exactly like this: http://support.hp.com/us-en/document/c00814731#N72 (chapter "Start a restore from the hard drive and the computer is off")...

  .. until step 10, which States:

  "The computer restarts and continues in the installation of Windows. Complete the configuration screens and wait until the computer finishes the installation program. "Then turn off the computer, reconnect all devices and turn on the computer.

  Yes, the computer restarts. She continues in the Windows installation (it says "medan windows konfigurerar datorn Vanta", which means roughly "Please wait while Windows configures the computer"). After that which was for about 5-10 minutes, the text disappears and the computer restarts by itself.

  After that, he gives a normal load Windows Vista bar and after that black screen. It seems to be a little bit alive but jammed somehow. If I let it be for several hours, he goes to the standby mode. If I wake up, he still won't. I can plug a USB another keyboard and he will make some access to hard drive (load a driver probably). I can press the sleep button and it will go into sleep mode. But if I press the power button / stop briefly, it will NOT stop.

  So finally, after several hours I forced to shut down (by pressing the power button / stop longer). When I start it, it goes back to behave as explained in the previous paragraph.

  If I press F8 during startup and select Safe mode, it goes in safe mode and I get dialogue indicating in Finnish:

  «Asenna Windows: Windows ei voi suorittaa vikasietotilassa asennusta.» See devam fenetresdans asennusta uudelleen tietokoneen kaynnistamalla. »

  Rough translation:

  "Installation of Windows: Windows cannot complete installation in safe mode." "You can continue the installation by restarting the computer.

  If I restart the computer, it goes back to the black screen after the windows loading bar.

  This suggests that there is something in the installation of Windows who jams it.

  I can install Windows Vista from a Vista DVD, but then I can't use the software included with the computer. (App States installation cannot install on a machine that is unauthorized, then of course they are looking for some OEM HP things.)

  Any suggestions on how to fix jam that continues with installing Recovery Windows or how to install the software on a normal Vista would be very appreciated.

  I solved the problem. Good thing I didn't order the restore disks, because that would not have solved the problem.

  I decided to post it because I don't know there will be others who have HP Pavilion Elite m9754sc and will have to face this problem of a black screen after the restoration.

  The fact is that the restore worked perfectly, but in this display card driver is buggy and it causes the screen to go black.

  I thought that what I installed fresh Vista which worked until I installed the driver from the recovery partition display. I tried VGA, outputs HDMI and DVI on the factory installed GeForce GT220 and none worked.

  A defective display driver should normally be no problem we could go in safe mode and fix it to the it. But as with the recovery goes to pre install state (ask what language to use etc.), safe mode does not work.

  So the solution is to unlock the display of the motherboard connectors and remove the factory installed GeForce GT220. Once the recovery and installation of Windows is finished using the graphics card integrated motherboards, you can reconnect the GeForce GT220 and get a updated driver with safe mode.

• Black screen after startup for 30 sec as if my network is enabled.

  So my problem is that I mentioned above. If I disable my router with its button to completely close and bad to start the computer, my PC starts in 5-7 seconds.

  If I turn on my router my PC goes black screen after the loading screen logo of blue windows and wait like 30 sec or sometimes 1 min, before sharing the login screen.
  I tried to make my static rather than dynamic, same IP occur.

  Hello

  Thanks for the updates.

  Did you check with the router manufacturer to see if the firmware updates are available for the same?

  Since the problem started once you have this connection, you must get in touch with the ISP or router manufacturer to check the issue.

  Hope the helps of information. Let us know if you need help with Windows related issues. We will be happy to help you.

• Black screen after entering the password to open Windows Vista

  I need help for vista windows Desktop to appear. All I get is the black screen after I get my password

  Aziz I apologize not responding earlier! In fact, I had to do was reboot the pc! I wish I knew exactly what it was that I did!

• computer only blinked a cursor in the corner of a black screen after that it shuts down. Was it an accident?

  Original title: was it an accident?

  My computer only blinked a cursor in the corner of a black screen after that it shuts down. then the fan stopped running current and the screen went blank, but I could still hear the hard drive running. Was it an accident?

  Yep, especially if she does not return.

• Pavilion 15 - p065tx: Pavilion 15 - p065tx, black screen after BIOS update recommended by HP assistant

  System reboot with black screen after accepting the update of the BIOS recommended by HP assistant this morning. AC power on at least three hours of waiting after the process completed successfully with auto update reboots always.

  Power light is on. Wired broadband light is turned on. Light CAP LOCK keyboard and led speaker hold noway.

  Hard reset has been tried 3 times with no improvement.

  External monitor is connected but no signal has been out of the laptop, screen is black.

  Done a few times this page to reset the BIOS setting blindly:

  http://support.HP.com/us-en/document/c02217843

  BEEPS heard when you press F10 or F5 during procedures. But still black screen.

  What can I try again?  Please advice kindly!

  Hi @ sokw,

  I have read and reviewed the post. Thanks for your reply. It seems that bios is damaged, and that is why the computer does not start. As it cannot be fixed by any software troubleshooting, you will need to contact the HP support by phone for the machine.

  HP technical support are available by clicking on the following link:
  
  http://h22207.www2.HP.com/us-en/?openCLC=true
  
  (1) once the page opens, please select the country in which you are located. Then enter your model of HP on the right number.
  
  (2) then choose "Contact the Support" tab at the top and scroll to the bottom of the page "HP Support - contact" to fill out the form with your details.
  
  (3) Once finished, click the "Show Options" at the bottom right.
  
  (4) Finally, scroll to the bottom of the page and select "Get a phone number." A file number and telephone number will now fill for you.

  I hope this helps. I would like to know how this happens. I really hope that the problem is solved without hassle and the unit works very well. Believe me, I've done everything I can to help by keeping your interests in mind. Please reach out for questions and I'll be there for you help.

  Just to say thank youPlease click the ' Thumbs Up 'button to give a Kudos to appreciate my efforts to help me. If it helps, Please mark this "accepted Solution" because it will help many other people with the same problem to get it resolved without hassle.

  Now carefully and have a wonderful week ahead.

• Re: Satellite L675-10 t black screen after disassembly problem

  Hi all

  I recently had some problems with my L675-10T overheating, even when I was with a big fan of cooling for the games.

  I realized that the problem resulted from blocked exhaust and dust and it is why, after reading and watching the many tutorials, I opened my laptop computer successfully and all cleaned up.

  The temperature dropped to 20 c and I was happy.

  The next night, however, took my laptop and headed for the living room, and it will stop.
  Black screen and nothing passed. So I ran to the internet and found this solution, it worked btw.

  1. turn off your computer
  2. unplug all wires (including energy)
  3. disconnect the battery from the bottom of the computer.
  4 re - connect the power cable. (the battery should not be in the computer)
  5. turn power on. The screen works. Choose start windows normally. (if you get this screen)

  The thing is, the same thing happened to me this morning as well.
  Twice in 2 days and im a little worried I did something wrong during Assembly of the laptop or something. Any ideas? Or do I keep accountant with the above solution?
  Looks like a mess of power upwards of sorts.

  Thank you in advance.

  Hello

  I assume that this question has not happened before you have disassembled the laptop. Right?
  To be honest this similar issue happened to me to. The portable light not (black screen) after I'm entered in the mode 'sleep'. However, this happened only once

  It s hard to tell why this happened to you it of not impossible that you have damaged something for disassembled the procedure.

  However, the fact is that the warranty is not valid more because you opened the laptop. That is why any approach (especially parts replacement) to solve this problem would cost money.
  So ultimately it s your decision: a technician visit to downtown to see the pieces of equipment or keep your stay with the workaround mentioned above.

• Black screen after the attempt to upgrade to windows 10

  I was trying to upgrade windows 7 on a laptop HP Windows 10. The first attempt was via the white windows logo in the taskbar. This attempt was interrupted, probably accidentally turned off the button wifi trying to move the computer. The second time I tried to use windows ten upgraded Installer. I did the usual download and installed up to 99%. He remained on the installation of 99% during the night and the next morning without change. I turned off the computer and he made a series of updates before shutting down for good. When it starts again, it has a black screen but the cursor is there and movable. I tried in safe mode for the repair and restoration of the system, but it did not work. I tried to reset the BIOS to default, but does not. I try to leave the computer turned off for an extended period of time disconnected from the internet to see if that helps. The last attempt to start, windows 7 seems to start but then ends up on the black screen and I held down the power button to stop it. I'd rather upgrade to windows 10 if possible, but if cannot then if can go back to windows 7 will be enough. It worked great on Windows 7 before trying to upgrade, so there is no problems with the computer.

  Hi Chris,

  I'll be happy to help you with the problem you have with black screen.

  The problem may occur if the video drivers are not updated.

  What is the model of your HP computer?

  I suggest you follow the suggestions by Sharath Srinivasan replied on August 7, 2015, the link below:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_10-hardware/black-screen-after-upgrading-to-Windows-10/cf3b4559-67d8-40E0-9cf2-ebf4528e1e78

  Please reply with the results, we are happy to help you.

  Thank you.

• Satellite M70 - black screen after the installation of recovery

  So far, what I did is put in the Recovery DVD - ROM product. Then when my computer restarts I was invited to restore my computer failing and said. After that he went through this process, that he told me to remove the disc that I did. Now he only get a black screen after the Toshiba screen that gives me options f2 for Setup and f12 for options.

  I don't know what to do now to make my laptop works again. Help, please.

  Hi Zach_1,

  Have you tried to launch the installation of recovery again? Maybe that something was wrong during the first installation, it might have arrived
  Then retry the recovery facility and see what happens.

  If it doesn't work you should try a normal Microsoft disk so determine if the problem is related to hardware or recovery disk.

• Corrupt BIOS V5 531 Acer black screen after startup, f2 and f12 also. Repairable?

  Hello

  Yesterday I tried to install Win 7 if I could play D & D Neverwinter on Arc after using * nix systems study (looking to start a career as an administrator). I had plugged into a power strip that was, unbeknownst to me, turned off and I went to make coffee and watch some news. When I came back to check the progress of my laptop was powered off and since then I havn't been avle start without being blocked at a black screen after the start page of the bios. The f2 and f12 also leads to a black screen, I can not change the boot device or enter the bios Setup.

  Is - fixable at all? For example, is the a key-combo, I can use it to restore from a backup bios? Or, do I have to bring in a technician who can install a new chip bios or flash this old some how? Or did I brick pemanently my device?

  V1.22 is what you want to be part of a unit of Windows 7.

  The problem is if it crashed during the upgrade process, it will take some special tools clearly on the chip on the MB and recharge it with a new BIOS. I would contact your local support team to see what options are available.

• Pavilion 15-243cl after automatic update of windows 8.1 I get a black screen after the home page.

  recently installed an automatic update of windows 8.1. Now, I get a black screen after the home page. I can load the Task Manager and access the internet. tried to go to the SafeMode to start with f8, but several attempts failed. I updated my graphics driver from AMD today and same black screen. I've also restored sytem to an earlier date using the HP utility with results screen - black even after the home page.

  Hello

  Try the following.

  Boot the computer normally and log.

  Black screen, old the ctrl and alt keys and press delete.

  Select Task Manager.

  Click on file and select the new task.

  Type rstrui - also enter a tick in the box for "create this task with administrative privileges" - and click on Ok.

  When the system restore interface is loaded, choose a restore point at least 48 hours before the opening of session question (IE before the last batch of Windows updates have been applied) occurred initially and then proceed to the system restore.

  Kind regards

  DP - K